Rear Axle - Rear Drive Shaft
Exploded View

| 1. | Circular clip | 2. | Dust shield | 3. | Housing |
| 4. | Snap ring | 5. | Spider assembly | 6. | Boot band |
| 7. | Boot | 8. | Shaft | 9. | Circular clip |
| 10. | Joint sub-assembly | 11. | Dust shield | Wheel side | |
| : Fill NISSAN genuine grease or an equivalent. | |||||
| : Always replace after every disassembly. | |||||
Disassembly and Assembly
DISASSEMBLY
Final Drive Side
Fix shaft with a vise.
Remove boot bands, and then remove boot from housing.
Put matching marks on housing and shaft.
Put matching marks (A) on the spider assembly and shaft.

Remove snap ring (1), and then remove spider assembly from shaft.

Remove boot from shaft.
Remove circular clip housing.
Remove dust shield to housing.
Remove old grease on housing with paper towels.
Perform inspection after disassembly. Refer to Inspection.
Wheel Side
Fix shaft with a vise.
Remove boot bands. Then remove boot from joint sub-assembly.
Screw drive shaft puller (A) (commercial service tool) into joint sub-assembly screw part to a length 30 mm (1.18 in) or more. Support drive shaft with one hand and pull out joint sub-assembly from shaft.

Remove circular clip from shaft.
Remove boot from shaft.
Remove old grease on joint sub-assembly with paper towels.
Perform inspection after disassembly. Refer to Inspection.
ASSEMBLY
Final drive Side
Wrap serration on shaft with tape (A) to protect boot from damage. Install new boot and boot band to shaft.

Remove the tape wrapped around the serrated on shaft.
To install the spider assembly (1), align it with the matching marks (A) on the shaft (2) during the removal, and direct the serration mounting surface (B) to the shaft.

Secure spider assembly onto shaft with snap ring (1).

Assemble the housing onto spider assembly, and apply the balance of the specified amount grease.
| Standard | |
| Grease amount | : Refer to Drive Shaft. |
Align matching marks painted when housing were removed.
Install boot securely into grooves (indicated by “*” marks) shown in the figure.

To prevent from deformation of the boot, adjust the boot installation length to the value shown below (L) by inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging inside air.
| Standard | |
| L | : Refer to Drive Shaft. |
Install new boot bands securely.
For low profile type bandPut boot band in the groove on drive shaft boot. Then fit pawls (
) into holes to temporary installation.
Pinch projection on the band with suitable pliers to tighten band.

Insert tip of band below end of the pawl.
Secure the boot bands using the boot band crimping tool (A) (SST: KV40107300).


M : 1.0 - 4.0 mm (0.04 - 0.16)
Secure housing and shaft, and then make sure that they are in the correct position when rotating boot. Install them with new boot band when the mounting positions become incorrect.
Install dust shield to housing.
Install circular clip to housing.
Perform inspection after assembly. Refer to Inspection.
Wheel Side
Fill serration slot joint sub-assembly (1) with NISSAN genuine grease or equivalent until the serration slot and ball groove become full to the brim.

Wrap serrated part of shaft with tape (A). Install boot band and boot to shaft. Be careful not to damage boot.

Remove the tape wrapped around the serrated on shaft.
Position circular clip on groove at the shaft edge.
Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with circular clip joint sub-assembly.
Install joint sub-assembly to shaft using plastic hammer.

Apply the balance of the specified amount of grease into the boot inside from large diameter side of boot.
| Standard | |
| Grease amount | : Refer to Drive Shaft. |
Install the boot securely into grooves (indicated by “*” marks) shown in the figure.

To prevent from deformation of the boot, adjust the boot installation length to the specified value shown below (L) by inserting the suitable tool into inside of the boot from the large diameter side of boot and discharging the inside air.
| Standard | |
| L | : Refer to Drive Shaft. |
Secure large and small ends of boot with new boot bands as shown in the figure.
For low profile type bandSet boot band to the drive shaft boot groove and temporarily fix pawl (A) of boot band to (B) of boot band.

Tighten boot band protrusions (B) with boot band crimping tool (SST: KV40107310) (A) in the direction shown by arrows (
).

Secure the boot bands using the boot band crimping tool (A) (SST: KV40107300).


M : 2.3 mm (0.091 in) max
Secure housing and shaft, and then make sure that they are in the correct position when rotating boot. Install them with new boot band when the mounting positions become incorrect.
Inspection
INSPECTION AFTER REMOVAL
Move joint up/down, left/right, and in the axial direction. Check for motion that is not smooth and for significant looseness.
Check boot for cracks or other damage, and also for grease leakage.

If a malfunction is found, disassemble drive shaft, and then replace with new one.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace if there are any abnormal condition.
Joint Sub-Assembly (Wheel Side)
Check the following:
Joint sub-assembly for rough rotation and excessive axial looseness.
The inside of the joint sub-assembly for entry of foreign material.
Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and Spider assembly (Final Drive Side)
Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider roller contact surface.
INSPECTION AFTER INSTALLATION
Check wheel sensor harness for proper connection. Refer to Exploded View.
If pressing the piston of rear brake caliper assembly, perform "REMOVAL/REPLACEMENT OF REAR BRAKE PAD OR REAR BRAKE CALIPER". Refer to Description.
Check wheel alignment. Refer to Inspection.
Adjust neutral position of steering angle sensor. Refer to Description.