Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit)

In this manual: Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
84steps
~504min
4/5difficulty
Done 0 of 84
  • C053c Wheel Speed Sensor
  • U0101 Can Comm Circuit
  • U0122 Vehicle Dynamics Control Module
  • U012e Engine Communication
  • U0155 Can Communication (ipc)
  • U0284 Active Grille Shutter
  • U1000 Can Communication Circuit
  • U1040 Eng Comm Circuit
  • U1327 Mac Key
  • U2118 Can Comm Circuit
  • U2141 Can Comm Circuit

C053c Wheel Speed Sensor Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C053C 00

Wheel speed sensor

(Wheel speed sensor generic range/performance)
Diagnosis condition Engine running
Signal Nissan Pathfinder Vehicle speed signal
Threshold Wheel sensor signal is invalid.
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Wheel sensor

  • ABS actuator and control unit (control unit)

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC C053C is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC C053C is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Check DTC with ABS actuator and electric unit (control unit). Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform trouble shooting relevant to DTC indicated.

CHECK WHEEL SENSOR

Check wheel sensor. Refer to DTC Diagnosis Procedure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace malfunctioning part.

U0101 Can Comm Circuit Nissan Pathfinder Fifth generation

DTC Description

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a Nissan Pathfinder vehicle, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U0101 00

LOST COMM (TCM)

(Lost communication with TCM)
Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold ECM is not transmitting or receiving CAN communication signal of OBD (emission related diagnosis) with TCM
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication line between TCM and ECM (CAN communication line is open or shorted)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 3 seconds.

  2. Check DTC.

Is DTC U0101 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

Proceed to Trouble Diagnosis Flow Chart.

U0122 Vehicle Dynamics Control Module Nissan Pathfinder SUV

DTC Description

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a Nissan Pathfinder vehicle, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detecting condition
U0122 00

VDC MDL

(Lost communication with Nissan Pathfinder vehicle dynamics control module)
Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication
Threshold When ECM is not transmitting or receiving CAN communication signal of OBD (emission related diagnosis) with ABS actuator and electric unit (control unit)
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Harness or connectors (CAN communication line is open or shorted)

FAIL-SAFE

When a DTC is detected, ECM executes a mode (in the Fail-safe mode) applicable to the DTC. The fail-safe mode has the preset traveling control mode (accelerator angle variation and engine output limit) and device fix mode.

Fail safe modeNissan Pathfinder Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 3 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

INSPECTION END

DTC Diagnosis Procedure

Proceed to Trouble Diagnosis Flow Chart.

U012e Engine Communication Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U012E 00

Communication error (lost)

(Lost communication with camshaft position control module)
Diagnosis condition Engine running at idle
Signal (terminal) Engine communication signal
Threshold Internal error of the electric intake valve timing control module is detected
Diagnosis delay time —

POSSIBLE CAUSE

  • Electric intake valve timing control module

  • ECM

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).
Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V when ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is DTC U012E detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ENGINE COMMUNICATION CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector and electric intake valve timing (IVT) control module harness connector.

  3. Check the continuity between ECM harness connector and electric IVT control module harness connector.

    ECMElectric IVT control moduleContinuity
    ConnectorTerminalConnectorTerminal
    E32 189 F99 102 Existed
    190 111
  4. Check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

REPLACE ELECTRIC IVT CONTROL MODULE

  1. Replace electric IVT control module. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Confirmation Procedure.

Is DTC U012E detected again?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

U0155 Can Communication (ipc) Nissan Pathfinder 2022

DTC Description

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent malfunction detection ability. Many electronic control units are equipped onto a Nissan Pathfinder vehicle, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control unit is connected with 2 communication lines (CAN-H and CAN-L) allowing a high rate of information transmission with less wiring. Each control unit communicates data but selectively reads required data only.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U0155 00

LOST COMM (METER)

(Lost communication with instrument panel cluster (IPC) control module)
Diagnosis condition —
Signal (terminal) —
Threshold A DTC is set if ECM cannot receive the CAN communication signals from combination meter.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Harness or connectors

(CAN communication line is open or shorted.)

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If another “DTC CONFIRMATION PROCEDURE” is performed just before the next test, turn the ignition switch OFF and wait for 10 seconds or more, then perform the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Start the engine and wait for 2 seconds or more.

  2. Check “Self Diagnostic Result” of “ENGINE”.

Is DTC U0155 detected?

YES>>

Go to DTC Diagnosis Procedure.

NO>>

Go to Intermittent Incident.

DTC Diagnosis Procedure

CHECK CAN COMMUNICATION CIRCUIT

Refer to Trouble Diagnosis Flow Chart.

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

Repair or replace damaged parts.

U0284 Active Grille Shutter Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

When ECM cannot receive the engine communication signal from active grille shutter.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detecting condition
U0284 00

LOST COMM (A/GRLL SHTTR MDL A)

(Lost communication with active grille air shutter module A)
Diagnosis condition Ignition switch ON
Signal (terminal) Engine communication signal
Threshold ECM cannot receive the engine communication signal from active grille shutter
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness and connectors (Engine communication line is open or circuit shorted.)

  • Active grille shutter

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC U0284 is displayed with another DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If another DTC Confirmation Procedure is conducted just before this procedure, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 10 V or more with ignition switch ON.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC U0284 is displayed with another DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect active grille shutter harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between active grille shutter harness connector and ground as follows.

    +−Condition

    Voltage

    (Approx.)
    Active grille shutter
    ConnectorTerminal
    E202 1 Ground Ignition switch: ON Battery voltage
    Ignition switch: OFF 0 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between active grille shutter harness connector and IPDM E/R harness connector.

    Active grille shutterIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    E202 1 E120 8 Existed

Is the inspection result normal?

YES>>

Perform trouble diagnosis for power supply circuit.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER GROUND CIRCUIT

  1. Turn ignition switch OFF

  2. Check the continuity between active grille shutter harness connector and ground.

    Active grille shutter−Continuity
    ConnectorTerminal
    E202 4 Ground Existed
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK ACTIVE GRILLE SHUTTER INPUT SIGNAL CIRCUIT

  1. Disconnect ECM harness connector.

  2. Check the continuity between ECM harness connector and active grille shutter harness connector.

+–Continuity
ECMActive grille shutter
ConnectorTerminalConnectorTerminal
F79 167 E202 3 Existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER

Check active grille shutter. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace active grille shutter. Refer to Removal and Installation.

U1000 Can Communication Circuit Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1000 01

CAN COMM CIRCUIT

(CAN communication circuit)
Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold Communication signal other than OBD (emission related diagnosis) is not received between electric intake valve timing control module and ECM
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connectors (Engine communication line is open or shorted)

  • ECM

  • Electric intake valve timing control module

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC U1000 is displayed with DTC P0607, first perform the confirmation procedure (trouble diagnosis) for DTC P0607.

Is DTC P0607 detected?

YES>>

Perform diagnosis for P0607. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 3 seconds.

  2. Check 1st trip DTC.

Is DTC U1000 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC U1000 is displayed with DTC P0607, first perform the confirmation procedure (trouble diagnosis) for DTC P0607.

Is DTC P0607 detected?

YES>>

Perform diagnosis of P0607. Refer to DTC Description.

NO>>

GO TO 2.

CHECK ENGINE COMMUNICATION CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect electric intake valve timing control module harness connector.

  4. Check the continuity between ECM harness connector and electric intake valve timing control module harness connector.

    ECMElectric intake valve timing control moduleContinuity
    ConnectorTerminalConnectorTerminal
    E32 189 F99 102 Existed
    190 111
  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

REPLACE ELECTRIC INTAKE VALVE TIMING CONTROL MODULE

Replace electric intake valve timing control module. Refer to Removal and Installation.

>>

GO TO 5.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Reconnect all harness connectors disconnected.

  2. Turn ignition switch ON.

  3. Erase DTC.

  4. Perform DTC Confirmation Procedure.

    See DTC Description.

  5. Check 1st trip DTC.

Is the DTC U1000 displayed again?

YES>>

GO TO 6.

NO>>

INSPECTION END

REPLACE ECM

Replace ECM. Refer to Removal and Installation.

>>

INSPECTION END

U1040 Eng Comm Circuit Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

When ECM unable to transmit engine communication signal.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1040 00

ENG COMM CIRCUIT

(Engine communication circuit)
Diagnosis condition Ignition switch ON
Signal (terminal) Engine communication signal
Threshold ECM unable to transmit engine communication signal to generator
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (LIN communication circuit is open or shorted.)

  • ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If another DTC Confirmation Procedure is conducted just before this procedure, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

DTC Diagnosis Procedure

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ACTIVE GRILLE SHUTTER SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect active grille shutter harness connector.

  4. Check the continuity between ECM harness connector and active grille shutter harness connector.

    +−Continuity
    ECMActive grille shutter
    ConnectorTerminalConnectorTerminal
    F79 167 E202 3 Existed
  5. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

U1327 Mac Key Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1327 52

MAC Key update

(MAC Key update)
Diagnosis condition —
Signal (terminal) —
Threshold MAC key writing is incomplete.
Diagnosis delay time —
54 Diagnosis condition —
Signal (terminal) —
Threshold MAC key is not written after ECM replacement.
Diagnosis delay time —

POSSIBLE CAUSE

U1327–52

  • Network communication error between CONSULT and ECM

  • ECM used in other vehicles is installed in the Nissan Pathfinder vehicle

  • ECM

U1327–54

  • Writing of MAC key has not been executed

  • ECM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

U1327–52

CHECK DTC PRIORITY

If DTC U1327-52 is displayed with DTC U1327-54, first perform the trouble diagnosis for DTC U1327-54

Is DTC U1327-54 detected?

YES>>

Proceed to DTC U1327-54 DTC Description.

NO>>

GO TO 2

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Ignition switch ON.

  2. Perform “MAC key writing”. Refer to Description.

  3. Perform “MAC Diagnosis” of “ENGINE” using CONSULT.

Is DTC U1327-52 detected as the current malfunction?

YES>>

Refer toDiagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

U1327–54

CHECK DTC PRIORITY

With CONSULT

  1. Ignition switch ON.

  2. Perform “MAC Diagnosis” of “ENGINE” using CONSULT.

Is DTC U1327-54 detected as the current malfunction?

YES>>

Refer toDiagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

U1327–52

CHECK DTC PRIORITY

If DTC U1327-52 is displayed with DTC U1327-54, first perform the trouble diagnosis for DTC U1327-54.

Is DTC U1327 detected?

YES>>

Proceed to DTC Description.

NO>>

GO TO 2

PERFORM MAC KEY WRITING

With CONSULT

  1. Perform “MAC key writing”. Refer to Description.

  2. Perform “MAC Diagnosis” of “ENGINE” using CONSULT.

Is DTC U1327-52 detected?

YES>>

GO TO 3

NO>>

INSPECTION END

REPLACE ECM

Replace ECM. Refer to Removal and Installation.

>>

INSPECTION END

U1327–54

PERFORM MAC KEY WRITING

With CONSULT

  1. Perform “MAC key writing”. Refer to Description.

  2. Perform “MAC Diagnosis” of “ENGINE” using CONSULT.

Is DTC U1327-54 detected as the current malfunction?

YES>>

GO TO 2.

NO>>

INSPECTION END

PERFORM MAC KEY WRITING (SECOND TIMES)

With CONSULT

  1. Restart CONSULT.

  2. Perform “MAC key writing”. Refer to Description.

  3. Perform “MAC Diagnosis” of “ENGINE” using CONSULT.

Is DTC U1327-54 detected as the current malfunction?

YES>>

GO TO 3.

NO>>

INSPECTION END

PERFORM MAC KEY WRITING (THIRD TIMES)

With CONSULT

  1. Restart CONSULT.

  2. Perform “MAC key writing”. Refer to Description.

  3. Perform “MAC Diagnosis” of “ENGINE” using CONSULT.

Is DTC U1327-54 detected as the current malfunction?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

U2118 Can Comm Circuit Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2118 87

CAN comm err (Intelligent Key)

[CAN comm err (Intelligent Key)]
Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold ECM is not transmitting or receiving CAN communication signal other than OBD (emission related diagnosis).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connectors (CAN communication line is open or shorted)

  • ECM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC U2118 is displayed with DTC P0607, first perform the confirmation procedure (trouble diagnosis) for DTC P0607.

Is DTC P0607 detected?

YES>>

Proceed to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 3 seconds.

  2. Check 1st trip DTC.

Is DTC U2118 detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC U2118 is displayed with DTC P0607, first perform the confirmation procedure (trouble diagnosis) for DTC P0607.

Is DTC P0607 detected?

YES>>

Proceed to DTC Description.

NO>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

U2141 Can Comm Circuit Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2141 57

CAN comm err (TCM)

[CAN comm err (TCM)]
Diagnosis condition —
Signal (terminal) —
Threshold MAC communication error
Diagnosis delay time —
87 Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold ECM is not receiving CAN communication signal other than OBD (emission related diagnosis).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

U2141–57

  • MAC communication error

  • ECM used in other vehicles is installed in the Nissan Pathfinder vehicle

  • ECM

U2141–87

  • Harness or connectors (CAN communication line is open or shorted)

  • TCM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

U2141–57

CHECK DTC PRIORITY

If DTC U2141 is displayed with DTC U1327, first perform the trouble diagnosis for DTC U1327.

Is DTC U1327 detected?

YES>>

Proceed to DTC Description.

NO>>

GO TO 2.

CHECK MAC DIAGNOSIS

With CONSULT

  1. Ignition switch ON.

  2. Perform “MAC Diagnosis” mode of “ENGINE” using CONSULT.

Is DTC U2141 detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

U2141–87

CHECK DTC PRIORITY

If DTC U2141 is displayed with DTC P0607, first perform the confirmation procedure (trouble diagnosis) for DTC P0607.

Is DTC P0607 detected?

YES>>

Proceed to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 3 seconds.

  2. Check 1st trip DTC.

Is DTC U2141 detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

U2141–57

CHECK DTC PRIORITY

If DTC U2141 is displayed with DTC U1327, first perform the trouble diagnosis for DTC U1327.

Is DTC U1327 detected?

YES>>

Proceed to DTC Description.

NO>>

GO TO 2.

CHECK MAC DIAGNOSIS

With CONSULT

  1. Ignition switch ON.

  2. Perform “MAC Diagnosis” mode of “ENGINE” using CONSULT.

Is DTC U2141 detected with DTC U214F, U2152(with ProPILOT),U2175 and U2176 at the same time?

YES>>

all DTC codes are detected at the same time: Replace ECM. Refer to Removal and Installation.

NO>>

all DTC codes are not detected at the same time: GO TO 3.

CHECK CAN COMMUNICATION SYSTEM

Perform trouble diagnosis of CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

INSPECTION END

U2141–87

CHECK DTC PRIORITY

If DTC U2141 is displayed with DTC P0607, first perform the confirmation procedure (trouble diagnosis) for DTC P0607.

Is DTC P0607 detected?

YES>>

Proceed to DTC Description.

NO>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.