Engine Control System - System Description

In this manual: Engine Control System - System Description
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
18steps
~108min
5/5difficulty
Done 0 of 18

Component Parts ➤ Nissan Pathfinder 2026

Structure and Operation Nissan Pathfinder R53

Positive Crankcase Ventilation

Blow-by gas in the crank case is returned to the intake manifold to improve ventilation efficiency. This allows the intervals of engine oil change to be extended.

When the engine is in the low-middle load condition as shown in the figure , the blow-by gas goes to the intake manifold via the PCV valve.

In the general driving conditions, the capacity of the PCV valve is sufficient for treating the blow-by gas and a little amount of the fresh air.

The fresh air enters to the rocker cover from the air duct via a hose, and is guided to the crankcase.

When the engine is in the high load condition as shown in the figure , blow-by gas flows backward in the blow-by hose and gets sucked into air duct.

On Board Refueling Vapor Recovery (ORVR)

From the beginning of refueling, the air and vapor inside the fuel tank go through refueling EVAP vapor cut valve and EVAP/ORVR line to the EVAP canister. The vapor is absorbed by the EVAP canister and the air is released to the atmosphere.

When the refueling has reached the full level of the fuel tank, the refueling EVAP vapor cut valve is closed and refueling is stopped because of auto shut-off. The vapor which was absorbed by the EVAP canister is purged during driving.

  • Put a “CAUTION: FLAMMABLE” sign in workshop.

  • Never smoke while servicing fuel system. Keep open flames and sparks away from work area.

  • Always furnish the workshop with a CO2 fire extinguisher.

System ➤ Nissan Pathfinder 5th Gen

Operation Nissan Pathfinder SUV

Autmatic Speed Control Device (ascd)

Switch Name and Function

SWITCHES AND INDICATORS

CRUISE indicator CANCEL switch RES/+ switch
SET/- switch ASCD MAIN switch
On the combination meter (Information display) On the steering wheel

SET SPEED RANGE

ASCD system can be set the following vehicle speed.

Minimum speed (Approx.)Maximum speed (Approx.)
40 km/h 144 km/h

SWITCH OPERATION

ItemFunction
CANCEL switch Cancels the cruise control driving.
RES/+ switch
  • Resumes the set speed.

  • Increases speed incrementally during cruise control driving.

SET/- switch
  • Sets desired cruise speed.

  • Decreases speed incrementally during cruise control driving.

ASCD MAIN switch Master switch to activate the ASCD system.

CANCEL OPERATION

When any of following conditions exist, cruise operation will be canceled.

  • CANCEL switch is pressed

  • More than 2 switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)

  • Brake pedal is depressed

  • Selector lever is in the N, P, R position

  • Nissan Pathfinder Vehicle speed decreased to 13 km/h lower than the set speed

  • TCS system is operated

When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform the driver by blinking indicator lamp.

  • Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE lamp may blink slowly.

    When the engine coolant temperature decreases to the normal operating temperature, CRUISE lamp will stop blinking and the cruise operation will be able to work by pressing COAST/SET switch or ACCEL/RES switch.

  • Malfunction for some self-diagnoses regarding ASCD control: SET indicator will blink quickly.

If MAIN switch is turned to OFF while ASCD is activated, all of ASCD operations will be canceled and Nissan Pathfinder vehicle speed memory will be erased.

Stop/start System

Switch Name and Function

SWITCHES AND INDICATORS

1. Stop/start indicator 2. Stop/start OFF switch
A. On the information display B. Lower instrument panel (driver side)

SYSTEM CONTROL CONDITION DISPLAY

Stop/start Indicator Lamp Status

System conditionConditionStop/start indicator lampWarning chime
Operate Normal Illuminate —
Hood open* High speed blinking Sound
Normal operation: Stop/Start system inhibited state

System conditions excluded failure are not satisfied.

(Battery state of charge, A/C steering operation, driver′s seat belt is unbuckled etc)

Illuminate

—
Fail-Safe Starter motor operation counter: too much Slow speed blinking —
Malfunction of stop/start system Slow speed blinking —

*: Engine is stalled after alert for 1.5 seconds.

Stop/start Indicator Status (Information Display)

System conditionNissan Pathfinder Vehicle conditionWarning chimeStop/start indicator
Operate Normal —
The engine does not restart With intelligent key system Hood open*1 Sound
The stop/start system is OFF When the stop/start OFF switch is ON.*2 —
When the brake pedal is not enough pressure. —
When A/C is prioritized. —
When the steering wheel is being operated. —
Others — —
The stop/start system is ON. When the stop/start OFF switch is OFF.*3 —
Fail-Safe Starter motor operation counter: too much —
Malfunction of stop/start system —

*1: Engine is stalled after alert for 1.5 seconds.

*2: This is indicated only for 1.5 seconds after the stop/start OFF switch is turned from OFF to ON.

*3: This is indicated only for 1.5 seconds after the stop/start OFF switch is turned from ON to OFF.

On Board Diagnostic (obd) System Nissan Pathfinder R53

Diagnosis Description

This system is an on board diagnostic system that records exhaust emission-related diagnostic information and detects a sensors/actuator-related malfunction. A malfunction is indicated by the malfunction indicator lamp (MIL) and stored in ECU memory as a DTC. The diagnostic information can be obtained with the diagnostic tool (GST: Generic Scan Tool).

GST (Generic Scan Tool)

When GST is connected with a data link connector equipped on the vehicle side, it will communicate with the control unit equipped in the Nissan Pathfinder vehicle and then enable various kinds of diagnostic tests. Refer to Diagnosis Description.

Diagnosis System (ecm) Nissan Pathfinder

Diagnosis Description

1st Trip Detection Logic and Two Trip Detection Logic

When a malfunction is detected for the first time, 1st trip DTC and 1st trip Freeze Frame data are stored in the ECM memory. The MIL will not illuminate at this stage. <1st trip>

If the same malfunction is detected again during the next drive, the DTC and Freeze Frame data are stored in the ECM memory, and the MIL illuminates. The MIL illuminates at the same time when the DTC is stored. <2nd trip> The “trip” in the “Two Trip Detection Logic” means a driving mode in which self-diagnosis is performed during Nissan Pathfinder vehicle operation. Specific on board diagnostic items will cause the ECM to illuminate or blink the MIL, and store DTC and Freeze Frame data, even in the 1st trip, as shown below.

×: Applicable —: Not applicable

ItemsMILDTC1st trip DTC
1st trip2nd trip1st trip displaying2nd trip displaying1st trip displaying2nd trip displaying
BlinkingIlluminateBlinkingIlluminate
Misfire (Possible three way catalyst damage) — DTC: P0300 - P0308 is being detected × — — — — — × —
Misfire (Possible three way catalyst damage) — DTC: P0300 - P0308 is being detected — — × — — × — —
One trip detection diagnoses. Refer to DTC Index. — × — — × — — —
Except above — — — × — × × —

DTC and Freeze Frame Data

DTC AND 1ST TRIP DTC

The 1st trip DTC (whose number is the same as the DTC number) is displayed for the latest self-diagnostic result obtained. If the ECM memory was cleared previously, and the 1st trip DTC did not recur, the 1st trip DTC will not be displayed.

If a malfunction is detected during the 1st trip, the 1st trip DTC is saved in the ECM memory. The MIL will not light up (two trip detection logic). If the same malfunction is not detected in the 2nd trip (meeting the required driving pattern), the 1st trip DTC is cleared from the ECM memory. If the same malfunction is detected in the 2nd trip, both the 1st trip DTC and DTC are saved in the ECM memory and the MIL lights up. In other words, the DTC is stored in the ECM memory and the MIL lights up when the same malfunction occurs in two consecutive trips. If a 1st trip DTC is stored and a non-diagnostic operation is performed between the 1st and 2nd trips, only the 1st trip DTC will continue to be stored. For malfunctions that blink or light up the MIL during the 1st trip, the DTC and 1st trip DTC are stored in the ECM memory.

For malfunctions in which 1st trip DTCs are displayed, refer to DTC Index. These items are required by legal regulations to continuously monitor the system/component. In addition, the items monitored non-continuously are also displayed on CONSULT.

1st trip DTC is specified in Service $07 of SAE J1979/ISO 15031-5. 1st trip DTC detection occurs without illuminating the MIL and therefore does not warn the driver of a malfunction.

When a 1st trip DTC is detected, check, print out or write down and erase (1st trip) DTC and Freeze Frame data as specified in Work Flow procedure Step 2, refer to Work Flow. Then perform DTC Confirmation Procedure or Component Function Check to try to duplicate the malfunction. If the malfunction is duplicated, the item requires repair.

FREEZE FRAME DATA AND 1ST TRIP FREEZE FRAME DATA

The ECM records the driving conditions such as fuel system status, calculated load value, engine coolant temperature, short term fuel trim, long term fuel trim, engine speed, Nissan Pathfinder vehicle speed, absolute throttle position, base fuel schedule and intake air temperature at the moment a malfunction is detected.

Data which are stored in the ECM memory, along with the 1st trip DTC, are called 1st trip freeze frame data. The data, stored together with the DTC data, are called freeze frame data and displayed on CONSULT or GST. The 1st trip freeze frame data can only be displayed on the CONSULT screen.

Only one set of freeze frame data (either 1st trip freeze frame data or freeze frame data) can be stored in the ECM. 1st trip freeze frame data is stored in the ECM memory along with the 1st trip DTC. There is no priority for 1st trip freeze frame data and it is updated each time a different 1st trip DTC is detected. However, once freeze frame data (2nd trip detection/MIL on) is stored in the ECM memory, 1st trip freeze frame data is no longer stored. Remember, only one set of freeze frame data can be stored in the ECM. The ECM has the following priorities to update the data.

PriorityItems
1 Freeze frame data

Misfire — DTC: P0300 - P0308

Fuel Injection System Function — DTC: P0171, P0172, P0174, P0175
2 Except the above items
3 1st trip freeze frame data

For example, the EGR malfunction (Priority: 2) was detected and the freeze frame data was saved in the 2nd trip. After that when the misfire (Priority: 1) is detected in another trip, the freeze frame data will be updated from the EGR malfunction to the misfire. The 1st trip freeze frame data is updated each time a different malfunction is detected. There is no priority for 1st trip freeze frame data. However, once freeze frame data is stored in the ECM memory, 1st trip freeze data is no longer stored (because only one freeze frame data or 1st trip freeze frame data can be stored in the ECM). If freeze frame data is stored in the ECM memory and freeze frame data with the same priority occurs later, the first (original) freeze frame data remains unchanged in the ECM memory.

Both 1st trip freeze frame data and freeze frame data (along with the DTCs) are cleared when the ECM memory is erased.

Counter System

RELATIONSHIP BETWEEN MIL, 1ST TRIP DTC, DTC, AND DETECTABLE ITEMS

  • When a malfunction is detected for the first time, the 1st trip DTC and the 1st trip freeze frame data are stored in the ECM memory.

  • When the same malfunction is detected in two consecutive trips, the DTC and the freeze frame data are stored in the ECM memory, and the MIL will come on.

  • The MIL will turn OFF after the Nissan Pathfinder vehicle is driven 3 times (driving pattern B) with no malfunction. The drive is counted only when the recorded driving pattern is met (as stored in the ECM). If another malfunction occurs while counting, the counter will reset.

  • The DTC and the freeze frame data will be stored until the Nissan Pathfinder vehicle is driven 40 times (driving pattern A) without the same malfunction recurring (except for Misfire and Fuel Injection System). For Misfire and Fuel Injection System, the DTC and freeze frame data will be stored until the Nissan Pathfinder vehicle is driven 80 times (driving pattern C) without the same malfunction recurring. The “TIME” in “SELF-DIAGNOSTIC RESULTS” mode of CONSULT will count the number of times the Nissan Pathfinder vehicle is driven.

  • The 1st trip DTC is not displayed when the self-diagnosis results in OK for the 2nd trip.

COUNTER SYSTEM CHART

ItemsFuel Injection SystemMisfireOther
MIL (turns OFF) 3 (pattern B) 3 (pattern B) 3 (pattern B)
DTC, Freeze Frame Data (no display) 80 (pattern C) 80 (pattern C) 40 (pattern A)
1st Trip DTC (clear) 1 (pattern C), *1 1 (pattern C), *1 1 (pattern B)
1st Trip Freeze Frame Data (clear) *1, *2 *1, *2 1 (pattern B)

For details about patterns B and C under “Fuel Injection System” and “Misfire”, see “EXPLANATION FOR DRIVING PATTERNS FOR “MISFIRE <EXHAUST QUALITY DETERIORATION>”, “FUEL INJECTION SYSTEM”.

For details about patterns A and B under Other, see “EXPLANATION FOR DRIVING PATTERNS FOR “MISFIRE <EXHAUST QUALITY DETERIORATION>”, “FUEL INJECTION SYSTEM”.

  • *1: Clear timing is at the moment OK is detected.

  • *2: Clear timing is when the same malfunction is detected in the 2nd trip.

Relationship Between MIL, DTC, 1st Trip DTC and Driving Patterns for “Misfire <Exhaust Quality Deterioration>”, “Fuel Injection System”

*1: When the same malfunction is detected in two consecutive trips, MIL will light up. *2: MIL will turn OFF after Nissan Pathfinder vehicle is driven 3 times (pattern B) without any malfunctions. *3: When the same malfunction is detected in two consecutive trips, the DTC and the freeze frame data will be stored in ECM.
*4: The DTC and the freeze frame data will not be displayed any longer after Nissan Pathfinder vehicle is driven 80 times (pattern C) without the same malfunction. (The DTC and the freeze frame data still remain in ECM.) *5: When a malfunction is detected for the first time, the 1st trip DTC and the 1st trip freeze frame data will be stored in ECM. *6: The 1st trip DTC and the 1st trip freeze frame data will be cleared at the moment OK is detected.
*7: When the same malfunction is detected in the 2nd trip, the 1st trip freeze frame data will be cleared. *8: 1st trip DTC will be cleared when Nissan Pathfinder vehicle is driven once (pattern C) without the same malfunction after DTC is stored in ECM.

Explanation for Driving Patterns for “Misfire <Exhaust Quality Deterioration>”, “Fuel Injection System”

Driving Pattern B

Refer to Driving Pattern.

Driving Pattern C

Refer to Driving Pattern.

Example:

If the stored freeze frame data is as per the following:

Engine speed: 850 rpm, Calculated load value: 30%, Engine coolant temperature: 80 °C

To be satisfied with driving pattern C, the vehicle should run under the following conditions:

Engine speed: 475 – 1,225 rpm, Calculated load value: 27 – 33%, Engine coolant temperature: more than 70 °C

Relationship Between MIL, DTC, 1st Trip DTC and Driving Patterns Except For “Misfire <Exhaust Quality Deterioration>”, “Fuel Injection System”

*1: When the same malfunction is detected in two consecutive trips, MIL will light up. *2: MIL will turn OFF after Nissan Pathfinder vehicle is driven 3 times (pattern B) without any malfunctions. *3: When the same malfunction is detected in two consecutive trips, the DTC and the freeze frame data will be stored in ECM.
*4:

The DTC and the freeze frame data will not be displayed any longer after Nissan Pathfinder vehicle is driven 40 times (pattern A) without the same malfunction.

(The DTC and the freeze frame data still remain in ECM.)
*5: When a malfunction is detected for the first time, the 1st trip DTC and the 1st trip freeze frame data will be stored in ECM. *6: 1st trip DTC will be cleared after Nissan Pathfinder vehicle is driven once (pattern B) without the same malfunction.
*7: When the same malfunction is detected in the 2nd trip, the 1st trip freeze frame data will be cleared.

Explanation for Driving Patterns Except for “Misfire <Exhaust Quality Deterioration>”, “Fuel Injection System”

Driving Pattern A

Refer to Driving Pattern.

Driving Pattern B

Refer to Driving Pattern.

Driving Pattern

DRIVING PATTERN A

Driving pattern A means a trip satisfying the following conditions.

  • Engine speed reaches 400 rpm or more.

  • Engine coolant temperature rises by 20 °C or more after starting the engine.

  • Engine coolant temperature reaches 70 °C or more.

  • The ignition switch is turned from ON to OFF.

DRIVING PATTERN B

Driving pattern B means a trip satisfying the following conditions.

  • Engine speed reaches 400 rpm or more.

  • Engine coolant temperature reaches 70 °C or more.

  • Nissan Pathfinder Vehicle speed of 70 – 120 km/h is maintained for 60 seconds or more under the control of closed loop.

  • Nissan Pathfinder Vehicle speed of 30 – 60 km/h is maintained for 10 seconds or more under the control of closed loop.

  • Under the closed loop control condition, the following state reaches 12 seconds or more in total: Nissan Pathfinder Vehicle speed of 4 km/h or less with idling condition.

  • The state of driving at 10 km/h or more reaches 10 minutes or more in total.

  • A lapse of 22 minutes or more after engine start.

DRIVING PATTERN C

Driving pattern C means operating vehicle as per the following:

The following conditions should be satisfied at the same time:

Engine speed: (Engine speed in the freeze frame data) ±375 rpm

Calculated load value: (Calculated load value in the freeze frame data) x (1±0.1) [%]

Engine coolant temperature condition:

  • When the freeze frame data shows lower than 70 °C, engine coolant temperature should be lower than 70 °C.

  • When the freeze frame data shows higher than or equal to 70 °C, engine coolant temperature should be higher than or equal to 70 °C.

DRIVING PATTERN D

Driving pattern D means a trip satisfying the following conditions.

  • The state of driving at 40 km/h reaches 300 seconds or more in total.

  • Idle speed lasts 30 seconds or more.

  • A lapse of 600 seconds or more after engine start.

System Readiness Test (SRT) Code

System Readiness Test (SRT) code is specified in Service $01 of SAE J1979/ISO 15031-5.

As part of an enhanced emissions test for Inspection & Maintenance (I/M), certain states require the status of SRT be used to indicate whether the ECM has completed self-diagnosis of major emission systems and components. Completion must be verified in order for the emissions inspection to proceed.

If a vehicle is rejected for a State emissions inspection due to one or more SRT items indicating “INCMP”, use the information in this Service Manual to set the SRT to “CMPLT”.

In most cases the ECM will automatically complete its self-diagnosis cycle during normal usage, and the SRT status will indicate “CMPLT” for each application system. Once set as “CMPLT”, the SRT status remains “CMPLT” until the self-diagnosis memory is erased.

Occasionally, certain portions of the self-diagnostic test may not be completed as a result of the customer's normal driving pattern; the SRT will indicate “INCMP” for these items.

If, during the state emissions inspection, the SRT indicates “CMPLT” for all test items, the inspector will continue with the emissions test. However, if the SRT indicates “INCMP” for one or more of the SRT items the Nissan Pathfinder vehicle is returned to the customer untested.

SRT SET TIMING

SRT is set as “CMPLT” after self-diagnosis has been performed one or more times. Completion of SRT is done regardless of whether the result is OK or NG. The set timing is different between OK and NG results and is shown in the table below.

Self-diagnosis resultExample
Diagnosis

Ignition cycle

← ON → OFF ← ON → OFF ← ON → OFF ← ON →
All OK Case 1 P0400 OK (1) — (1) OK (2) — (2)
P0402 OK (1) — (1) — (1) OK (2)
P1402 OK (1) OK (2) — (2) — (2)
SRT of EGR “CMPLT” “CMPLT” “CMPLT” “CMPLT”
Case 2 P0400 OK (1) — (1) — (1) — (1)
P0402 — (0) — (0) OK (1) — (1)
P1402 OK (1) OK (2) — (2) — (2)
SRT of EGR “INCMP” “INCMP” “CMPLT” “CMPLT”
NG exists Case 3 P0400 OK OK — —
P0402 — — — —
P1402 NG — NG

NG

(Consecutive NG)

(1st trip)

DTC
1st trip DTC — 1st trip DTC

DTC

(= MIL ON)
SRT of EGR “INCMP” “INCMP” “INCMP” “CMPLT”

OK: Self-diagnosis is carried out and the result is OK.

NG: Self-diagnosis is carried out and the result is NG.

—: Self-diagnosis is not carried out.

When all SRT related self-diagnoses show OK results in a single cycle (Ignition OFF-ON-OFF), the SRT will indicate “CMPLT”. → Case 1 above

When all SRT related self-diagnoses show OK results through several different cycles, the SRT will indicate “CMPLT” at the time the respective self-diagnoses have at least one OK result. → Case 2 above

If one or more SRT related self-diagnoses show NG results in 2 consecutive cycles, the SRT will also indicate “CMPLT”. → Case 3 above

The table above shows that the minimum number of cycles for setting SRT as “INCMP” is the number one (1) for each self-diagnosis (Case 1 & 2) or the number two (2) for one of self-diagnoses (Case 3). However, in preparation for the state emissions inspection, it is unnecessary for each self-diagnosis to be executed twice (Case 3) for the following reasons:

  • The SRT will indicate “CMPLT” at the time the respective self-diagnoses have one (1) OK result.

  • The emissions inspection requires “CMPLT” of the SRT only with OK self-diagnosis results.

  • During SRT driving pattern, the 1st trip DTC (NG) is detected prior to “CMPLT” of SRT and the self-diagnosis memory must be erased from the ECM after repair.

  • If the 1st trip DTC is erased, all the SRT will indicate “INCMP”.

Permanent Diagnostic Trouble Code (Permanent DTC)

Permanent DTC is defined in SAE J1979/ISO 15031-5 Service $0A.

ECM stores a DTC issuing a command of turning on MIL as a permanent DTC and keeps storing the DTC as a permanent DTC until ECM judges that there is no presence of malfunction.

Permanent DTCs cannot be erased by using the Erase function of CONSULT or Generic Scan Tool (GST) and by disconnecting the battery to shut off power to ECM. This prevents a Nissan Pathfinder vehicle from passing the state emission inspection without repairing a malfunctioning part.

When not passing the state emission inspection due to more than one permanent DTC, permanent DTCs should be erased, referring to this manual.

PERMANENT DTC SET TIMING

The setting timing of permanent DTC is stored in ECM with the lighting of MIL when a DTC is confirmed.

Malfunction Indicator Lamp (MIL)

  • When detecting a DTC that affects exhaust gas, the exhaust emission-related control module transmits a malfunction indicator lamp signal to ECM via CAN communication line.

    ECM prioritizes (MIL: ON/blink) the signal received from the exhaust emission-related control module and the ECM-stored DTC that affects exhaust gas and transmits a malfunction indicator lamp signal to the combination meter via CAN communication line.

    The combination meter turns ON or blinks the MIL, according to the signal transmitted from ECM, and alerts the driver of malfunction detection.

  • Control modules that a DTC of MIL ON/Blink is stored (Control module varies among DTCs.):

    • ECM

    • TCM

  1. The MIL illuminates when ignition switch is turned ON (engine is not running).

  2. When the engine is started, the MIL should go off.

On Board Diagnosis Function

ON BOARD DIAGNOSIS ITEM

The on board diagnostic system has the following functions.

Diagnostic test modeFunction
Bulb check MIL can be checked.
SRT status ECM can read if SRT codes are set.
Malfunction warning If ECM detects a malfunction, it illuminates or blinks MIL to inform the driver that a malfunction has been detected.
Accelerator pedal released position learning ECM can learn the accelerator pedal released position. Refer to Description.
Throttle valve closed position learning ECM can learn the throttle valve closed position. Refer to Description.
Electric intake valve timing control learning The initial position of the electric intake valve timing control actuator can be adjusted. Refer to Description.

BLUB CHECK MODE

Description

This function allows damage inspection in the MIL bulb (blown, open circuit, etc.).

Operation Procedure

  1. Turn ignition switch ON.

  2. The MIL on the instrument panel should stay ON.

    If it remains OFF, check MIL circuit. Refer to Diagnosis Procedure.

SRT STATUS MODE

Description

This function allows to read if ECM has completed the self-diagnoses of major emission control systems and components. For SRT, refer to System Readiness Test (SRT) Code.

Operation Procedure

  1. Turn ignition switch ON and wait 20 seconds.

  2. SRT status is indicated as shown blow.

    • ECM continues to illuminate MIL if all SRT codes are set.

    • ECM blinks MIL for about 10 seconds if all SRT codes are not set.

MALFUNCTION WARNING MODE

Description

In this function ECM turns on or blinks MIL when it detects a malfunction in the emission control system components and/or the powertrain control components (which affect Nissan Pathfinder vehicle emissions) to inform the driver that a malfunction has been detected.

Operation Procedure

  1. Turn ignition switch ON.

  2. Check that MIL illuminates.

    If it remains OFF, check MIL circuit. Refer to Diagnosis Procedure.

  3. Start engine and let it idle.

    • For two trip detection logic diagnoses, ECM turns on MIL when it detects the same malfunction twice in the two consecutive driving cycles.

    • For 1st trip detection logic diagnoses, ECM turns on MIL when it detects a malfunction in one driving cycle.

    • ECM blinks MIL when it detects a malfunction that may damage the three way catalyst (misfire).

CONSULT Function

FUNCTION

Diagnostic test modeCGW StatusFunction
Restricted ModeDiag Test ModeOpen Mode
Self Diagnostic Result Display Display Display Self-diagnostic results such as 1st trip DTC, DTCs and 1st trip freeze frame data or freeze frame data can be read and erased quickly.*1 Display non-network DTC which ECM memorizes.
CGW Information*2 Display*2 Display*2 Display*2
  • Display the current CGW mode*2

  • Enables CGW to switch mode*2

Data Monitor Display Display Display Input/Output data in the ECM can be read.
Work Support*2 Non-display*2 Non-display*2 Display*2 This mode enables a technician to adjust some devices faster and more accurately by following the indications on the CONSULT unit.
Active Test*2 Non-display*2 Display*2 Display*2 Diagnostic Test Mode in which CONSULT drives some actuators apart from the ECMs and also shifts some parameters in a specified range.
ECU Identification Display Display Display ECM part number can be read.
DTC Work Support Non-display Display Display SRT and operating condition to check DTC can be confirmed.
MAC Diagnosis*3 Display Display Display

Display MAC diagnosis result divided into the following two inspection priorities.

  • Inspection Priority 1: Root cause

  • Inspection Priority 2

CAN Diag Support Monitor*3 Display Display Display
Network DTC*3 Display Display Display Display network DTC which ECM memorizes when performing "Diagnosis (All System)".

*1: The following emission-related diagnostic information is cleared when the ECM memory is erased.

  • DTC (Diagnostic trouble codes)

  • 1st trip diagnostic trouble codes

  • Freeze frame data

  • 1st trip freeze frame data

  • System readiness test (SRT) codes

  • Test values

*2: In some vehicles, it is not malfunctioning in case of no display of "CGW Information". In this case, it is not necessary to switch the CGW status. In Nissan Pathfinder vehicles where "CGW information" is not displayed, "Work Support" and "Active Test" are always displayed.

*3: Displays when performing "Diagnosis (All System)".

CGW INFORMATION

Display the diagnosis mode which a user can perform in Diag Test mode/Open Mode by switching the CGW status form Restricted mode to Diag Test Mode/Open Mode.

For the method of switching CAN Gateway status, Refer to CONSULT Function.

SELF DIAGNOSTIC RESULT MODE

Self Diagnostic Item

Regarding items of DTC and 1st trip DTC, refer to DTC Index.

How to Read DTC and 1st Trip DTC

DTCs and 1st trip DTCs related to the malfunction are displayed in “Self-diag results”.

  • When ECM detects a 1st trip DTC, “1t” is displayed for “TIME”.

  • When ECM has detected a current DTC, “0” is displayed for “TIME”.

  • If “TIME” is neither “0” nor “1t”, the DTC occurred in the past and ECM shows the number of times the Nissan Pathfinder vehicle has been driven since the last detection of the DTC.

How to Erase DTC and 1st Trip DTC

Freeze Frame Data and 1st Trip Freeze Frame Data

Freeze frame data item*Description
DIAG TROUBLE CODE [PXXXX] The engine control component part/control system has a trouble code that is displayed as PXXXX. Refer to DTC Index.
CAL/LD VALUE [%] The calculated load value at the moment a malfunction is detected is displayed.
COOLANT TEMP [°C] or [°F] The engine coolant temperature at the moment a malfunction is detected is displayed.
L-FUEL TRM-B1 [%]
  • “Long-term fuel trim” at the moment a malfunction is detected is displayed.

  • The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule than short-term fuel trim.

L-FUEL TRM-B2 [%]
S-FUEL TRM-B1 [%]
  • “Short-term fuel trim” at the moment a malfunction is detected is displayed.

  • The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel schedule.

S-FUEL TRM-B2 [%]
ENGINE SPEED [rpm] The engine speed at the moment a malfunction is detected is displayed
VEHICL SPEED [km/h] or [mph] The Nissan Pathfinder vehicle speed at the moment a malfunction is detected is displayed
ABSOL TH·P/S [%] The throttle valve opening angle at the moment a malfunction is detected is displayed
B/FUEL SCHDL [msec] The base fuel schedule at the moment a malfunction is detected is displayed
INT/A TEMP SE [°C] or [°F] The intake air temperature at the moment a malfunction is detected is displayed
FUEL SYS-B1
  • “Fuel injection system status” at the moment a malfunction is detected is displayed.

  • One of the following mode is displayed.

    Mode2: Open loop due to detected system malfunction

    Mode3: Open loop due to driving conditions (power enrichment, deceleration enleanment)

    Mode4: Closed loop - using oxygen sensor(s) as feedback for fuel control

    Mode5: Open loop - has not yet satisfied condition to go to closed loop

FUEL SYS-B2
INT MANI PRES [kPa] These items are displayed but are not applicable to this model.
COMBUST CONDITION
FUEL RAIL PRESSURE [MPa] The fuel rail pressure at the moment a malfunction is detected is displayed.
TARGET FUEL RAIL PRESSURE [MPa] The target fuel rail pressure at the moment a malfunction is detected is displayed.
BATTERY VOLTAGE [V] The battery voltage at the moment a malfunction is detected is displayed.
FUEL LEVEL [%] The fuel level at the moment a malfunction is detected is displayed.
ODO/TRIP METER [km] The ODO/TRIP at the moment a malfunction is detected is displayed.
DTC count The engine control component part/control system has a trouble code the is displayed

*: The items are the same as those of 1st trip freeze frame data.

DATA MONITOR MODE

Monitored Item

Monitored itemUnitMonitor Item SelectionDescriptionRemarks
ECU INPUT SIGNALSMAINSIGNALSStop/Start error
COOLANT TEMP/S °C or °F × × The engine coolant temperature (determined by the signal voltage of the engine coolant temperature sensor) is displayed. When the engine coolant temperature sensor is open or short-circuited, ECM enters fail-safe mode. The engine coolant temperature determined by the ECM is displayed.
VHCL SPEED SE km/h or mph × × The Nissan Pathfinder vehicle speed computed from the vehicle speed signal sent from combination meter is displayed.
BATTERY VOLT V The power supply voltage of ECM is displayed.
INT/A TEMP SE °C or °F × × The intake air temperature (determined by the signal voltage of the intake air temperature sensor) is indicated.
PURG VOL C/V %
  • Indicates the EVAP canister purge volume control solenoid valve control value computed by the ECM according to the input signals.

  • The opening becomes larger as the value increases.

FUEL T/TMP SE °C or °F The fuel temperature (determined by the signal voltage of the fuel tank temperature sensor) is displayed.
FUEL LEVEL SE V × The signal voltage of the fuel level sensor is displayed.
EVAP SYS PRES V The signal voltage of EVAP control system pressure sensor is displayed.
CAL/LD VALUE % “Calculated load value” indicates the value of the current air flow divided by peak air flow.
HO2S2 (B1) V × × The signal voltage of the heated oxygen sensor 2 is displayed.
HO2S2 (B2)
ENG OIL TEMP °C or °F The engine oil temperature (determined by the signal voltage of the engine oil temperature sensor) is displayed.
A/F ALPHA-B1 % The mean value of the air-fuel ratio feedback correction factor per cycle is indicated.
  • When the engine is stopped, a certain value is indicated.

  • This data also includes the data for the air-fuel ratio learning control.

  • Specification value is indicated on monitor screen under the following conditions.

    • Reference: Select

    • Display type: Line graph

A/F ALPHA-B2
A/F S1 HTR (B1)

%

  • Air fuel ratio (A/F) sensor 1 heater control value computed by ECM according to the input signals.

  • The current flow to the heater becomes larger as the value increases.

A/F S1 HTR (B2)
EXH/V TIM B1 °CA Indicates [°CA] of exhaust camshaft retard angle.
EXH/V TIM B2
Ignition timing deg × ×

Indicates the ignition timing computed by ECM according to the input signals.

  • When the engine is stopped, a certain value is indicated.

FAN DUTY % Indicates a command value for cooling fan. The value is calculated by ECM based on input signals.
FUEL PUMP DUTY — The control condition of the fuel pump control module (FPCM) (determined by ECM according to the input signals) is indicated.
THRTL STK CNT B1 —
ENG SPEED rpm × × Indicates the engine speed computed from the signal of the crankshaft position sensor (POS) and camshaft position sensor (PHASE).
  • Accuracy becomes poor if engine speed drops below the idle rpm.

  • If the signal is interrupted while the engine is running, an abnormal value may be indicated.

TRVL AFTER MIL km or mile Distance traveled while MIL is activated.
B/FUEL SCHDL ms × × “Base fuel schedule” indicates the fuel injection pulse width programmed into ECM, prior to any learned on board correction.

Specification value is indicated on monitor screen under the following conditions.

  • Reference: Select

  • Display type: Line graph

MASS AIRFLOW g/s Indicates the mass air flow computed by ECM according to the signal voltage of the mass air flow sensor.
FUEL PRES SEN MPa Indicates the fuel rail pressure computed by ECM according to the input signals.
ACCEL SEN 1 V The accelerator pedal position sensor signal voltage is displayed. ACCEL SEN 2 signal is converted by ECM internally. Thus, they differs from ECM terminal voltage signal.
ACCEL SEN 2
TP SEN 1-B1 V × × The throttle position sensor signal voltage is displayed. TP SEN 2-B1 signal is converted by ECM internally. Thus, they differs from ECM terminal voltage signal.
TP SEN 2-B1
FUEL INJ B1 msec ECM-calculated injection pulse width of the fuel injector on the Bank 1 side.
FUEL INJ B2
I/P PULLY SPD rpm Indicates the engine speed computed from the input speed sensor signal.
Nissan Pathfinder Vehicle SPEED km/h or mph The vehicle speed computed from the Nissan Pathfinder vehicle speed signal sent from TCM is displayed.
AC PRESS SEN V The signal voltage from the refrigerant pressure sensor is displayed.
A/F SEN1 (B1) V × × The A/F signal computed from the input signal of the air fuel ratio (A/F) sensor 1 is displayed.
A/F SEN1 (B2)
VHCL SPEED SE km/h or mph The Nissan Pathfinder vehicle speed computed from the vehicle speed signal sent from combination meter is displayed.
VTC DTY EX B1 % The control condition of the exhaust valve timing control solenoid valve (determined by ECM according to the input signals) is indicated.
VTC DTY EX B2
A/F ADJ-B1 — Indicates the correction of factor stored in ECM. The factor is calculated from the difference between the target air-fuel ratio stored in ECM and the air-fuel ratio calculated from A/F sensor 1 signal.
A/F ADJ-B2
INT/V TIM (B1) °CA Indicates [°CA] of intake camshaft advance angle.
INT/V TIM (B2)
H/P FUEL PUMP DEG deg Displays ECM-calculated fuel discharge position of the high pressure fuel pump.
FUEL PRES SEN V V The signal voltage of FRP sensor is displayed.
EOP SENSOR V The signal voltage of EOP sensor is displayed.
ECM TEMP 1 °C The ECM temperature is indicated.
ECM TEMP 2
Mass air flow sensor (HZ) B1 Hz The signal frequency of the mass air flow sensor is displayed.
LOAD SIGNAL On/Off × ×

Indicates [On/Off] condition from the electrical load signal.

  • On: Rear window defogger switch is ON and/or lighting switch is in 2nd position.

  • Off: Both rear window defogger switch and lighting switch are OFF.

AIR COND SIG On/Off × × Indicates [On/Off] condition of the air conditioner switch as determined by the air conditioner signal.
PW/ST SIGNAL On/Off × × [On/Off] condition of the power steering system (determined by the signal voltage of the power steering pressure sensor signal) is indicated.
P/N POSI SW On/Off × × Indicates [On/Off] condition from the park/neutral position (PNP) signal.
START SIGNAL On/Off Indicates start signal status [On/Off] computed by the ECM according to the signals of engine speed and battery voltage. After starting the engine, [Off] is displayed regardless of the starter signal.
CLSD THL POS On/Off × × Indicates idle position [On/Off] computed by ECM according to the accelerator pedal position sensor signal.
HO2S2 MNTR (B1) RICH/LEAN ×

Display of heated oxygen sensor 2 signal:

  • RICH: means the amount of oxygen after three way catalyst is relatively small.

  • LEAN: means the amount of oxygen after three way catalyst is relatively large.

When the engine is stopped, a certain value is indicated.
HO2S2 MNTR (B2) ×
IGNITION SW On/Off × × Indicates [On/Off] condition from ignition switch signal.
HEATER FAN SW On/Off × Indicates [On/Off] condition from the heater fan switch signal.
IDL A/V LEARN YET/CMPLT

Displays the condition of Idle Air Volume Learning

  • Yet: Idle air volume learning has not been performed yet.

  • CMPLT: Idle air volume learning has already been performed successfully.

BRAKE SW On/Off Indicates [On/Off] condition from the stop lamp switch signal.
COMBUSTION — These items are displayed but are not applicable to this model.
VIAS S/V-1 On/Off ×

The control condition of the VIAS control solenoid valve 1 (determined by ECM according to the input sig-nals) is indicated.

  • On: VIAS control solenoid valve 1 is operating

  • Off: VIAS control solenoid valve 1 is not operating

ENGINE MOUNT IDLE/TRVL

The control condition of the electronic controlled engine mount (determined by ECM according to the input signals) is indicated.

  • IDLE: Engine speed is below 950 rpm

  • TRVL: Engine speed is above 950 rpm

FUEL PUMP RLY On/Off Indicates the fuel pump relay control condition determined by ECM according to the input signals.
FPCM Hi/Mid/Low/Off The control condition of the fuel pump control module (FPCM) (determined by ECM according to the input signals) is indicated.
VENT CONT/V On/Off

The control condition of the EVAP canister vent control valve (determined by ECM according to the input signals) is indicated.

  • On: Closed

  • Off: Open

THRTL RELAY On/Off Indicates the throttle control motor relay control condition determined by the ECM according to the input signals.
HO2S2 HTR (B1) On/Off Indicates [On/Off] condition of heated oxygen sensor 2 heater determined by ECM according to the input signals.
HO2S2 HTR (B2)
DIST SW On/Off Indicates [On/Off] condition from DISTANCE switch signal.
BRAKE SW2 On/Off Indicates [On/Off] condition of stop lamp switch signal.
BRAKE SW1 On/Off Indicates [On/Off] condition from brake pedal position switch signal.
SET SW On/Off Indicates [On/Off] condition from COAST/SET switch signal.
RESUME/ACC SW On/Off Indicates [On/Off] condition from ACCEL/RES switch signal.
CANCEL SW On/Off Indicates [On/Off] condition from CANCEL switch signal.
MAIN SW On/Off Indicates [On/Off] condition from MAIN switch signal.
CRUISE LAMP On/Off Indicates [On/Off] condition of CRUISE lamp determined by the ECM according to the input signals.
VIAS S/V-2 On/Off

The control condition of the VIAS control solenoid valve 2 (determined by ECM according to the input sig-nals) is indicated.

  • On: VIAS control solenoid valve 2 is operating

  • Off: VIAS control solenoid valve 2 is not operating

HO2 S2 DIAG1 (B2) INCMP/CMPLT

Indicates DTC P0159 self-diagnosis (delayed response) condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

HO2 S2 DIAG1 (B1) INCMP/CMPLT

Indicates DTC P0139 self-diagnosis (delayed response) condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

HO2 S2 DIAG2 (B2) INCMP/CMPLT

Indicates DTC P0159 self-diagnosis (slow response) condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

HO2 S2 DIAG2 (B1) INCMP/CMPLT

Indicates DTC P0139 self-diagnosis (slow response) condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

EVAP LEAK DIAG YET/CMPLT

Indicates the condition of EVAP leak diagnosis.

  • Yet: EVAP leak diagnosis has not been performed yet.

  • CMPLT: EVAP leak diagnosis has been performed successfully.

EVAP DIAG READY On/Off

Indicates the ready condition of EVAP leak diagnosis.

  • On: Diagnosis has been ready condition.

  • Off: Diagnosis has not been ready condition.

SYSTEM 1 DIAGNOSIS A B2 INCMP/CMPLT

Indicates DTC P219B self-diagnosis condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

SYSTEM 1 DIAGNOSIS A B1 INCMP/CMPLT

Indicates DTC P219A self-diagnosis condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

A/F SEN1 DIAG1 (B2) INCMP/CMPLT

Indicates DTC P015C or P015D self-diagnosis condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

A/F SEN1 DIAG1 (B1) INCMP/CMPLT

Indicates DTC P015A or P015B self-diagnosis condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

A/F SEN1 DIAG2 (B2) INCMP/CMPLT

Indicates DTC P014E or P014F self-diagnosis condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

A/F SEN1 DIAG2 (B1) INCMP/CMPLT

Indicates DTC P014C or P014D self-diagnosis condition.

  • INCMP: Self-diagnosis is incomplete.

  • CMPLT: Self-diagnosis is complete.

SYSTEM 1 DIAGNOSIS B B2 ABSNT/PRSNT

Indicates DTC P219B self-diagnosis condition.

  • ABSNT: Self-diagnosis standby

  • PRSNT: Under self-diagnosis

SYSTEM 1 DIAGNOSIS B B1 ABSNT/PRSNT

Indicates DTC P219A self-diagnosis condition.

  • ABSNT: Self-diagnosis standby

  • PRSNT: Under self-diagnosis

A/F SEN1 DIAG3 (B2) ABSNT/PRSNT

Indicates DTC P014C, P014D, P015A or P015B self-diagnosis condition.

  • ABSNT: The Nissan Pathfinder vehicle condition is not within the diagnosis range.

  • PRSNT: The vehicle condition is within the diagnosis range.

A/F SEN1 DIAG3 (B1) ABSNT/PRSNT

Indicates DTC P014E, P014F, P015C or P015D self-diagnosis condition.

  • ABSNT: The Nissan Pathfinder vehicle condition is not within the diagnosis range.

  • PRSNT: The vehicle condition is within the diagnosis range.

ATOM PRES SEN 2 V The signal voltage from the manifold absolute pressure (MAP) sensor is displayed.
A/GRLL SHTTR POSITION F/CLOSE MOVING F/OPEN UNIDTF

Indicates the status of active grille shutter.

  • F/CLOSE: Active grille shutter is fully closed.

  • MOVING: Active grille shutter is in motion.

  • F/OPEN: Active grille shutter is fully opened.

  • UNIDTF: Unable to specify the shutter position.

STRT OPR TN CNTR count Starter motor operation counter is displayed. Indicated multiplication value of the starter motor operation of key switch operation and restart.
A/F LRN CNTR B2 —
A/F LRN CNTR B1 —
TOTAL DISTNC-OCS RST 1 km The Multi-way Control Valve position detected by the position sensor is displayed.
TOTAL DISTNC-OCS RST 2 km Total travel distance of odd meter when Oil Control System is reset.
TOTAL DISTNC-OCS RST 3 km Total travel distance of odd meter when Oil Control System is reset. (two times ago)
DETERIORTN VL-OCS RT 1 — Total travel distance of odd meter when Oil Control System is reset. (three times ago)
DETERIORTN VL-OCS RT 2 — Insicates deterioration condition of the engine oil when Oil Control System is reset.
DETERIORTN VL-OCS RT 3 — Insicates deterioration condition of the engine oil when Oil Control System is reset. (three times ago)
TOTAL DISTNC-OCS WRN 1 km Total travel distance of odd meter when Oil Control System remaining distance is zero.
TOTAL DISTNC-OCS WRN 2 km Total travel distance of odd meter when Oil Control System remaining distance is zero. (two times ago)
TOTAL DISTNC-OCS WRN 3 km Total travel distance of odd meter when Oil Control System remaining distance is zero. (two times ago)
DETERIORTN VL-OCS WRN 1 — Insicates deterioration condition of the engine oil when Oil Control System remaining distance is zero.
DETERIORTN VL-OCS WRN 2 — Insicates deterioration condition of the engine oil when Oil Control System remaining distance is zero. (two times ago)
DETERIORTN VL-OCS WRN 3 — Insicates deterioration condition of the engine oil when Oil Control System remaining distance is zero. (three times ago)
CURRENT DETERIORATN VAL — Insicates deterioration condition of the engine oil.
Brake operation judgment On/Off Indicates [On/Off] condition of Brake operation judgment.
A/GRLL SHTTR CALIBRATION INCMP/ CMPLT

Indicates initial position learning status of active grille shutter.

  • CMPLT: The leaning is complete.

  • INCOMP: The learning is incomplete.

A/GRLL SHTTR CIRCUIT DiAG OK/NG

Indicates the diagnosis result of active grille shutter circuit.

  • OK: Normal

  • NG: Malfunction detected.

A/GRLL SHTTR TEMP DIAG OK/NG

Indicates the diagnosis result of active grille shutter actuator temperature status.

  • OK: Normal

  • NG: Abnormal temperature detected.

A/GRLL SHTTR OVER RUN OK/NG

Indicates active grille shutter moves beyond normal moving limit.

  • OK: Normal

  • NG: Malfunction detected.

A/GRLL SHTTR STUCK OK/NG

Indicates the diagnosis result of active grille shutter stuck or the operation range less than normal.

  • OK: Normal

  • NG: Malfunction detected.

A/GRLL SHTTR CALIB DIAG OK/NG

Indicates the diagnosis result of initial position learning of active grille shutter.

  • OK: Normal

  • NG: Deficiency detected.

Starter motor (Counter) OK/NG × When the starter motor exceeds the specified No. of starting operation, NG is displayed.
Driver's seat belt switch OK/NG × When the malfunction of the Driver's seat belt switch is judged, OK or NG is displayed.
Engine parts OK/NG × When the malfunction of engine parts related to the stop/start system is judged, OK or NG is displayed.
ABS error OK/NG × When an ABS abnormality is received from the ABS actuator and electric unit, NG is displayed.
TCM error OK/NG × When an CVT abnormality is received from the TCM, NG is displayed.
TCM error B OK/NG × When an DTC abnormality is received from the TCM, NG is displayed.
VDC error OK/NG × When an VDC abnormality is received from the ABS actuator and electric unit, NG is displayed.
IPDM error OK/NG × When an abnormal voltage status is received from the IPDM E/R, NG is displayed.
CAN comm (VDC) A OK/NG × When the communication status with the ABS actuator and electric unit is judged, OK or NG is displayed.
CAN comm (VDC) B OK/NG × When the communication status with the ABS actuator and electric unit is judged, OK or NG is displayed.
CAN comm (VDC) C OK/NG × When VDC is judged based on the communication status with the ABS actuator and electric unit, OK or NG is displayed.
CAN comm (VDC) D OK/NG × When VDC is judged based on the communication status with the ABS actuator and electric unit, OK or NG is displayed.
CAN comm (VDC) E OK/NG × When VDC is judged based on the communication status with the ABS actuator and electric unit, OK or NG is displayed.
CAN comm (VDC) F OK/NG × When VDC is judged based on the communication status with the ABS actuator and electric unit, OK or NG is displayed.
CAN comm (VDC) G OK/NG × When VDC is judged based on the communication status with the ABS actuator and electric unit, OK or NG is displayed.
CAN comm (VDC) H OK/NG × When VDC is judged based on the communication status with the ABS actuator and electric unit, OK or NG is displayed.
CAN comm (TCM) A OK/NG × When A/T is judged based on the communication status with the TCM, OK or NG is displayed.
CAN comm (TCM) B OK/NG × When CVT is judged based on the communication status with the TCM, OK or NG is displayed.
CAN comm (TCM) C OK/NG × When A/T is judged based on the communication status with the TCM, OK or NG is displayed.
CAN comm (TCM) D OK/NG × When CVT is judged based on the communication status with the TCM, OK or NG is displayed.
CAN comm (TCM) E OK/NG × When A/T is judged based on the communication status with the TCM, OK or NG is displayed.
CAN comm (BCM) A OK/NG × When the communication status with the BCM is judged, OK or NG is displayed.
CAN comm (BCM) B OK/NG × When the communication status with the BCM is judged, OK or NG is displayed.
CAN comm (BCM) C OK/NG × When the communication status with the BCM is judged, OK or NG is displayed.
CAN comm (BCM) D OK/NG × When the communication status with the BCM is judged, OK or NG is displayed.
CAN comm (BCM) E OK/NG × When the communication status with the BCM is judged, OK or NG is displayed.
CAN comm (IPDM) A OK/NG × When the communication status with the IPDM E/R is judged, OK or NG is displayed.
CAN comm (IPDM) B OK/NG × When the communication status with the IPDM E/R is judged, OK or NG is displayed.
CAN comm (IPDM) C OK/NG × When the communication status with the IPDM E/R is judged, OK or NG is displayed.
CAN comm (IPDM) D OK/NG × When the communication status with the IPDM E/R is judged, OK or NG is displayed.
CAN comm (IPDM) E OK/NG × When the communication status with the IPDM E/R is judged, OK or NG is displayed.
Starter motor relay OK/NG × When the malfunction of the ST/IS relay is judged, OK or NG is displayed.
Neutral switch OK/NG × When the malfunction of the neutral switch is judged, OK or NG is displayed.
Clutch switch (Lower) OK/NG × When the malfunction of the Clutch switch (Lower) is judged, OK or NG is displayed.
Clutch switch (Upper) OK/NG × When the malfunction of the Clutch switch (Upper) is judged, OK or NG is displayed.
CAN comm (EPS) OK/NG × When the communication status with the steering control module is judged, OK or NG is displayed.
LIN comm (DC/DC) OK/NG × When the malfunction of DC/DC converter is received from LIN communication status, OK or NG is displayed.
Negative pressure OK/NG × When the brake booster pressure sensor status is judged, OK or NG is displayed.

WORK SUPPORT MODE

Work Item

WORK ITEMCONDITIONUSAGE
VIN REGISTRATION In this mode, VIN is registered in ECM. When registering VIN in ECM
EVAP SYSTEM CLOSE

Close the EVAP canister vent control valve in order to make EVAP system close under the following conditions.

  • Ignition switch ON

  • Engine not running

  • Ambient temperature is above 0 °C.

  • No vacuum and no high pressure in EVAP system

  • Fuel tank temp. is more than 0 °C.

  • Within 10 minutes after starting “EVAP SYSTEM CLOSE”

  • When trying to execute “EVAP SYSTEM CLOSE” Under the condition except above, CONSULT will discontinue it and display appropriate instruction.

When detecting EVAP vapor leak in the EVAP system
IDLE AIR VOL LEARN The idle air volume that keeps the engine within the specified range is memorized in ECM. When learning the idle air volume
SELF-LEARNING CONT The coefficient of self-learning control mixture ratio returns to the original coefficient. When clearing mixture ratio self-learning value
CLSD THL POS LEARN Ignition switch ON and engine stopped. When learning the throttle valve closed position
A/F INITIAL LEARNING Air fuel ratio learning frequency is low while idling, learning the air fuel ratio of the idling domain in ECM. When learning the air fuel ratio.
TARGET IGN TIM ADJ* Idle condition When adjusting target ignition timing
TARGET IDLE RPM ADJ* Idle condition When setting target idle speed
STRT OPRTN CNTR CLEAR — —
SAVING DATA FOR REPLC CPU In this mode, save data that is in ECM. When ECM is replaced.
WRITING DATA FOR REPLC CPU In this mode, write data stored by “SAVE DATA FOR CPU REPLC” in work support mode to ECM. When ECM is replaced.
ELECTRIC INTAKE VALVE TIMING CONTROL LEARNING Ignition switch ON and engine stopped.

After the following parts are replaced.

  • Electric intake valve timing control actuator

  • Electric intake valve timing control module

  • camshaft, timing chain, camshaft sprocket

  • piston, connecting rod, crankshaft

  • position sensor

Misfire count (real-time) These items are displayed but not used. —
Misfire count (past) These items are displayed but not used. —
Stop/Start prohibit cause data recorder Ignition switch: ON (Engine stopped) Indicates the reason that stop/start system does not operate when Nissan Pathfinder vehicle is stopped on CONSULT.
Stop/Start engine stall cause data recorder Ignition switch: ON (Engine stopped) Indicates the reason that engine is stalled on CONSULT.
Stop/Start engine restart cause data recorder Ignition switch: ON (Engine stopped) Indicates the reason that engine is restarted when stop/start system operates on CONSULT.
MAC KEY writing Ignition switch: ON Write MAC key to ECM.

*: This function is not necessary in the usual service procedure.

ACTIVE TEST MODE

Test Item

TEST ITEMCONDITIONJUDGEMENTCHECK ITEM (REMEDY)
AUTO STOP START

Engine: After warming up, run engine at idle

  • Selector lever: N or P

  • “Start” and “Cancel” using CONSULT

Check the stop/start system operate and restart.
  • Harness and connectors

  • IPDM E/R

  • Starter motor

  • Engine restart relay

  • Starter control relay

ENG COOLANT TEMP
  • Engine: Return to the original trouble condition

  • Change the engine coolant temperature using CONSULT.

If trouble symptom disappears, see CHECK ITEM.
  • Harness and connectors

  • Engine coolant temperature sensor

  • Fuel injector

FUEL INJECTION
  • Engine: Return to the original trouble condition

  • Change the amount of fuel injection using CONSULT.

If trouble symptom disappears, see CHECK ITEM.
  • Harness and connectors

  • Fuel injector

  • Air fuel ratio (A/F) sensor 1

PURG VOL CONT/V
  • Engine: After warming up, run engine at 1,500 rpm.

  • Change the EVAP canister purge volume control solenoid valve opening percent using CONSULT.

Engine speed changes according to the opening percent.
  • Harness and connectors

  • Solenoid valve

FUEL/T TEMP SEN Change the fuel tank temperature using CONSULT.
POWER BALANCE
  • Engine: After warming up, idle the engine.

  • A/C switch OFF

  • Selector lever: P or N

  • Cut off each injector signal one at a time using CONSULT.

Engine runs rough or dies.
  • Harness and connectors

  • Compression

  • Fuel injector

  • Power transistor

  • Spark plug

  • Ignition coil

EXT V/T ASSIGN ANGLE
  • Engine: Return to the original non-standard condition

  • Change exhaust valve timing using CONSULT.

If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors

  • Exhaust valve timing control solenoid valve

ENGINE MOUNTING
  • Ignition switch: ON

  • Turn electronic controlled engine mount “IDLE” and “TRVL” with CONSULT.

Electronic controlled engine mount makes the operating sound.
  • Harness and connectors

  • Electronic controlled engine mount

VIAS S/V-1
  • Ignition switch: ON (Engine stopped)

  • Turn solenoid valve “ON” and “OFF” using CONSULT and listen to operating sound.

Solenoid valve makes the operating sound
  • Harness and connectors

  • Solenoid valve

ACTIVE GRILLE SHUTTER

To check the operation of the active grille shutter, follow the steps below:

  1. Park the Nissan Pathfinder vehicle in a safe area and apply the parking brake.

  2. Start the engine or bring the vehicle into READY state.

  3. Press the "CALIBRTN" button.

  4. Select the "OPEN" or "CLOSE" button to check the operation.

Active grille shutter fully opens or fully closes.
  • Harness or connector

  • Active grille shutter actuator

  • Active grille shutter

VENT CONTROL/V
  • Ignition switch: ON (Engine stopped)

  • Turn solenoid valve “ON” and “OFF” with the CONSULT and listen to operating sound.

Solenoid valve makes an operating sound.
  • Harness and connectors

  • Solenoid valve

FAN DUTY CONTROL*
  • Ignition switch: ON

  • Change duty ratio using CONSULT.

Cooling fan speed changes.
  • Harness and connectors

  • Cooling fan motor

  • Cooling fan relay

  • Cooling fan control module

  • IPDM E/R

VIAS S/V-2
  • Ignition switch: ON (Engine stopped)

  • Turn solenoid valve “ON” and “OFF” using CONSULT and listen to operating sound.

Solenoid valve makes the operating sound
  • Harness and connectors

  • Solenoid valve

AUTO STOP START

Engine: After warming up, run engine at idle

  • Selector lever: N or P

  • “Start” and “Cancel” using CONSULT

Check the stop/start system operate and restart.
  • Harness and connectors

  • IPDM E/R

  • Starter motor

  • Engine restart relay

  • Starter control relay

FPCM
  • Engine: Return to the original trouble condition

  • Select “LOW”, “MID” and “HI” with CONSULT.

Fuel pump speed changes or stops.
  • Harness and connectors

  • Fuel pump control module (FPCM)

IGNITION TIMING
  • Engine: Return to the original trouble condition

  • Timing light: Set

  • Retard the ignition timing using CONSULT.

If trouble symptom disappears, see CHECK ITEM. Perform Idle Air Volume Learning.

*: Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.

DTC WORK SUPPORT MODE

Test Item
Test modeTest itemCorresponding DTC No.Reference page
A/F SEN1 A/F SEN1 (B1) P1275 — —
A/F SEN1 (B1) P1276 P0130 DTC Description
A/F SEN1 (B2) P1286 P0150 DTC Description
A/F SENSOR1 (B1) P014C/P014D — —
A/F SENSOR1 (B2) P014E/P014F — —
EVAPORATIVE SYSTEM PURG FLOW P0441 P0441 DTC Description
HO2S2 HO2S2 (B1) P1146 P0138 DTC Description
HO2S2 (B1) P1147 P0137 DTC Description
HO2S2 (B1) P0139 P0139 DTC Description
HO2S2 (B2) P1166 P0158 DTC Description
HO2S2 (B2) P1167 P0157 DTC Description
HO2S2 (B2) P0159 P0159 DTC Description

SRT STATUS Mode

  • For items whose SRT codes are set, “CMPLT” is displayed on the CONSULT screen; for items whose SRT codes are not set, “INCMP” is displayed.

  • “SRT STATUS” provides the presence or absence of permanent DTCs stored in ECM memory.

PERMANENT DTC STATUS Mode

How to Display Permanent DTC Status

  1. Turn ignition switch OFF and wait at 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at 10 seconds.

  4. Turn ignition switch ON.

  5. On CONSULT screen, select “SRT & P-DTC”>>“Permanent DTC Status”.

SRT WORK SUPPORT Mode

This mode enables a technician to drive a vehicle to set the SRT while monitoring the SRT status.

PERMANENT DTC WORK SUPPORT Mode

This mode enables a technician to drive a vehicle to complete the driving pattern that is required for erasing permanent DTC.