Driveline - Dtc/circuit Diagnosis

In this manual: Driveline - Dtc/circuit Diagnosis
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
65steps
~390min
5/5difficulty
Done 0 of 65
  • C1201-46 Controller
  • C1201-4b Controller
  • C1203-86 Abs System
  • C1210-97 Engine Signal
  • C1213-A2 Battery Voltage
  • C1215-12 Oil Temperature Sensor
  • C1220-54 Incomplete Air Bleeding
  • U3d02-06 Incomplete Programming
  • Power Supply and Ground Circuit
  • Awd Warning Icon/display
  • Transfer Oil Temperature Sensor

C1201-46 Controller Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1201-46

CONTROLLER

(Controller)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold Malfunction has occurred inside 4WD control unit
Diagnosis delay time 1 seconds or less

POSSIBLE CAUSE

Internal malfunction of 4WD control unit

FAIL-SAFE

Although 4WD control is canceled, the vehicle can drive at 2WD condition.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Wait for 15 seconds or more.

  3. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “C1201-46” detected?

YES>>

Proceed to diagnosis procedure: Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

  2. Ignition switch OFF, and wait for 10 seconds or more.

  3. Ignition switch ON, and wait for 15 seconds or more.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Which DTC is detected?

Including other DTC>>

Perform the trouble diagnosis for detected other DTC. Refer to DTC Index.

C1201-46 only>>

GO TO 2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check 4WD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1201-46” is detected, replace actuator assembly due to the malfunction of the 4WD control unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

C1201-4b Controller Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1201-4B

CONTROLLER

(Controller)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold 4WD control unit temperature value is too high
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

Internal malfunction of 4WD control unit

FAIL-SAFE

Although 4WD control is canceled, the vehicle can drive at 2WD condition.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Pathfinder vehicle.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “C1201-4B” detected?

YES>>

Proceed to diagnosis procedure: Refer toDTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Erase self diagnostic results for “ALL MODE AWD/4WD”.

  2. Ignition switch OFF, and wait for 10 seconds or more.

  3. Ignition switch ON, and wait for 15 seconds or more.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “C1201-4B” detected?

YES>>

Replace actuator assembly due to the malfunction of the 4WD control unit. Refer to Removal and Installation.

NO>>

Inspection End.

C1203-86 Abs System Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1203-86

ABS SYSTEM

(ABS system)
Diagnosis condition With ignition switch ON and Nissan Pathfinder vehicle running.
Signal (terminal) Wheel speed signals
Threshold 4WD control unit cannot receive the wheel speed signal.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

ABS malfunction (wheel speed signal error)

FAIL-SAFE

Although 4WD control is canceled, the vehicle can drive at 2WD condition.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Pathfinder vehicle.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “C1203-86” detected?

YES>>

Proceed to diagnosis procedure: Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

CONSULT

Select "Self Diagnostic Result" mode of “ABS”.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check 4WD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1203–86” is detected, replace actuator assembly due to the malfunction of the 4WD control unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

C1210-97 Engine Signal Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1210-97

ENGINE SIGNAL

(Engine signal)
Diagnosis condition When ignition switch is ON and engine is running.
Signal (terminal) Torque down impossible signal
Threshold Detected the signal malfunction related protection for 4WD system.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

The signal error related to 4WD system protection

FAIL-SAFE

Although 4WD control is canceled, the vehicle can drive at 2WD condition.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Pathfinder vehicle.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “C1210-97” detected?

YES>>

Proceed to diagnosis procedure: Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF 4WD CONTROL UNIT

CONSULT

  1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

  2. Start the engine, and wait for 15 seconds or more.

  3. Stop the engine.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Which DTC is detected?

C1210-97>>

GO TO 2.

Except C1210-97>>

Perform the trouble diagnosis for detected DTC. Refer to DTC Index.

No DTC>>

Inspection End.

PERFORM SELF-DIAGNOSIS OF ECM

CONSULT

Select "Self Diagnostic Result" mode of “ENGINE”.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

PERFORM SELF-DIAGNOSIS OF TCM

CONSULT

Select "Self Diagnostic Result" mode of “TRANSMISSION”.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 4.

CHECK TERMINALS AND HARNESS CONNECTORS

Check 4WD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1210-97” is detected, replace actuator assembly due to the malfunction of the 4WD control unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

C1213-A2 Battery Voltage Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1213-A2

BATTERY VOLTAGE

(Battery voltage)
Diagnosis condition When ignition switch is ON>
Signal (terminal) Battery power supply signal (terminal #6)
Threshold Battery power supply signal < 9 V
Diagnosis delay time 15 seconds or more

POSSIBLE CAUSE

The power supply in the system is too low.

FAIL-SAFE

Although 4WD control is canceled, the vehicle can drive at 2WD condition.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Pathfinder vehicle.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “C1213-A2” detected?

YES>>

Proceed to diagnosis procedure: Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis of the power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK TERMINALS AND HARNESS CONNECTORS

Check 4WD control unit pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

After ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1213-A2” is detected, replace actuator assembly due to the malfunction of the 4WD control unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

C1215-12 Oil Temperature Sensor Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1215-12

OIL TEMPERATURE SENSOR

(Oil temperature sensor)
Diagnosis condition When ignition switch is on and engine is running.
Signal (terminal) Transfer oil temperature signal (terminal #2)
Threshold Transfer oil temperature value is too high
Diagnosis delay time —

POSSIBLE CAUSE

  • Malfunction of transfer oil temperature sensor

  • Transfer oil temperature sensor circuit. (Sensor circuit is shorted)

FAIL-SAFE

Although 4WD control is canceled, the vehicle can drive at 2WD condition.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Pathfinder vehicle.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “C1215-12” detected?

YES>>

Proceed to diagnosis procedure: Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK TRANSFER OIL TEMPERATURE SENSOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect transfer oil temperature sensor harness connector.

  3. Check the continuity between transfer oil temperature sensor harness connector and ground.

    Transfer oil temperature sensor—Continuity
    ConnectorTerminal
    F2 2 Ground Yes

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace malfunctioning parts.

CHECK TRANSFER OIL TEMPERATURE SENSOR SIGNAL CIRCUIT

  1. Disconnect 4WD control unit harness connector.

  2. Check the continuity between 4WD control unit harness connector and transfer oil temperature sensor harness connector.

    4WD control unitTransfer oil temperature sensorContinuity
    ConnectorTerminalConnectorTerminal
    C1 2 F2 1 Yes
  3. Check the continuity between 4WD control unit harness connector and ground.

    4WD control unit—Continuity
    ConnectorTerminal
    C1 2 Ground No

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace malfunctioning parts.

CHECK TRANSFER OIL TEMPERATURE SENSOR SIGNAL

  1. Connect 4WD control unit harness connector.

  2. Ignition switch ON.

  3. Check the voltage between transfer oil temperature sensor harness connector and ground.

(+)(–)

Voltage

(Approx.)
Transfer oil temperature sensor
ConnectorTerminal
F2 2 Ground 4.75 – 5.25 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace malfunctioning parts.

CHECK TRANSFER OIL TEMPERATURE SENSOR

Check transfer oil temperature sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace transfer oil temperature sensor. Refer to Removal and Installation.

CHECK TERMINALS AND HARNESS CONNECTORS

  • Check 4WD control unit pin terminals for damage or loose connection with harness connector.

  • Check transfer oil temperature sensor pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

After ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1215-12” is detected, replace the 4WD control unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

C1220-54 Incomplete Air Bleeding Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1220-54

INCOMP AIR BLEEDING

(Incomplete air bleeding)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold Air bleeding of electro-hydraulic coupling oil was incomplete
Diagnosis delay time —

POSSIBLE CAUSE

  • Incomplete air bleeding of electro-hydraulic coupling oil

  • Electro-hydraulic coupling

FAIL-SAFE

Although 4WD control is canceled, the vehicle can drive at 2WD condition.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

  2. Ignition switch OFF, and wait for 10 seconds or more.

  3. Ignition switch ON, and wait for 15 seconds or more.

  4. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “C1220-54” detected?

YES>>

Proceed to diagnosis procedure: Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Perform air bleeding and initialize oil deterioration level. Refer to Description.

  2. Ignition switch OFF.

  3. Perform the “DTC CONFIRMATION PROCEDURE”. Refer to DTC Description.

Is DTC “C1220-54” detected?

YES>>

Replace electro-hydraulic coupling assembly. Refer to Removal and Installation.

NO>>

Inspection End.

U3d02-06 Incomplete Programming Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U3D02-06

INCOMP PROGRAMMING

(Incomplete programming)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold When programming to 4WD control unit is not complete.
Diagnosis delay time —

POSSIBLE CAUSE

  • Incomplete programming of 4WD control unit

  • 4WD control unit

FAIL-SAFE

Although 4WD control is canceled, the vehicle can drive at 2WD condition.

DTC Confirmation Procedure

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Wait for 15 seconds or more.

  3. Select "Self Diagnostic Result" mode of “ALL MODE AWD/4WD”.

Is DTC “U3D02-06” detected?

YES>>

Proceed to diagnosis procedure: Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM 4WD CONTROL UNIT PROGRAMMING

CONSULT

  1. Erase "Self Diagnostic Result" of “ALL MODE AWD/4WD”.

  2. Perform 4WD control unit programming. Refer to Description.

    • Suppose the 4WD control unit has been replaced.

  3. Ignition switch OFF.

  4. Perform the “DTC CONFIRMATION PROCEDURE”. Refer to DTC Confirmation Procedure.

Is DTC “U3D02-06” detected?

YES>>

GO TO 2.

NO>>

Inspection End.

CHECK TERMINALS AND HARNESS CONNECTORS

Check 4WD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After ignition switch OFF, perform DTC confirmation procedure again. If DTC “U3D02-06” is detected, replace actuator assembly due to the malfunction of the 4WD control unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

Power Supply and Ground Circuit Nissan Pathfinder Fifth generation

Diagnosis Procedure

CHECK FUSES

Check that the following fuses are not blown:

UnitPower sourceFuse No.Capacity
4WD control unit Battery 22 20 A
Ignition switch ON or START 9 10 A

Is the fuse blown?

YES>>

Replace the blown fuse after repairing the affected circuit.

NO>>

GO TO 2.

CHECK POWER SUPPLY CIRCUIT

  1. Disconnect 4WD control unit harness connector.

  2. Check voltage between 4WD control unit harness connector and ground.

    (+)(–)Ignition switch position
    4WD control unit
    ConnectorTerminalOFFONSTART
    C1 6 Ground Battery voltage Battery voltage Battery voltage
    5 0 V Battery voltage Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connector.

CHECK GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between 4WD control unit harness connector and ground.

    4WD control unit—Continuity
    ConnectorTerminal
    C1 1 Ground Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace harness or connector.

Awd Warning Icon/display Nissan Pathfinder R53

Diagnosis Procedure

CHECK POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis for power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the error-detected parts.

PERFORM SELF DIAGNOSTIC RESULT (4WD CONTROL UNIT)

CONSULT

Select “Self Diagnostic Result” mode of “ALL MODE AWD/4WD”.

Is any detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

PERFORM SELF DIAGNOSTIC RESULT (COMBINATION METER)

CONSULT

Select “Self Diagnostic Result” mode of “METER/M&A”.

Is any detected?

YES>>

Check the DTC. Refer to DTC Index (Full TFT Meter) or DTC Index (7 Inch Information Display).

NO>>

Perform the trouble diagnosis for combination meter power supply circuit. Refer to Diagnosis Procedure (Full TFT Meter) or Diagnosis Procedure (7 Inch Information Display).

Transfer Oil Temperature Sensor Nissan Pathfinder 2026

Component Inspection

CHECK TRANSFER OIL TEMPERATURE SENSOR

  1. Ignition switch OFF.

  2. Remove transfer oil temperature sensor. Refer to Exploded View.

  3. Check the resistance between transfer oil temperature sensor connector terminals.

    • Make measuring condition using burning hot water.

    Transfer oil temperature sensorCondition

    Resistance

    (Approx.)
    Terminals
    1 2 212°F (100°C) 5.563 – 6.997 kΩ

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace transfer oil temperature sensor. Refer to Exploded View.