Brake Control System - Basic Inspection

In this manual: Brake Control System - Basic Inspection
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
75steps
~450min
5/5difficulty
Done 0 of 75
  • Diagnosis and Repair Work Flow
  • Additional Service When Replacing Abs Actuator and Electric Unit (control Unit)
  • Configuration
  • Adjustment of Steering Angle Sensor Neutral Position
  • Calibration of Decel G Sensor
  • Adjustment of Brake Caliper Initial Position
  • Removal/replacement of Rear Brake Pad or Rear Brake Caliper
  • Change of System Mode

Diagnosis and Repair Work Flow Nissan Pathfinder R53

Work Flow

DETAILED FLOW

INTERVIEW FROM THE CUSTOMER

Clarify customer complaints before inspection. First of all, perform an interview utilizing Diagnostic Work Sheet and reproduce the symptom as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by driving Nissan Pathfinder vehicle with customer, if necessary.

>>

GO TO 2.

CHECK SYMPTOM

Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by interview. Also check that the symptom is not caused by fail-safe mode. Refer to Fail-Safe.

>>

GO TO 3.

PERFORM THE SELF-DIAGNOSIS

CONSULT

  1. Ignition OFF (Auto ACC function OFF) to ON.

  2. Select self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Record or print self-diagnosis results and freeze frame data (FFD). GO TO 4.

NO>>

GO TO 6.

RECHECK THE SYMPTOM

CONSULT

  1. Erase self-diagnostic results for “ABS”.

  2. Ignition OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  3. Perform DTC confirmation procedures for the error-detected system.

Is DTC detected?

YES>>

GO TO 5.

NO>>

Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.

REPAIR OR REPLACE ERROR-DETECTED PART

CONSULT

  1. Disconnect 12V battery negative terminal.

  2. Repair or replace error-detected parts.

  3. Reconnect part or connector after repairing or replacing.

  4. Connect 12V battery negative terminal.

  5. When DTC is detected, erase self-diagnostic result for “ABS”.

>>

GO TO 7.

IDENTIFY ERROR-DETECTED SYSTEM BY SYMPTOM DIAGNOSIS

Estimate error-detected system based on symptom diagnosis and perform inspection.

Can the error-detected system be identified?

YES>>

GO TO 7.

NO>>

Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.

FINAL CHECK

CONSULT

  1. Check the reference value for “ABS”.

  2. Recheck the symptom and check that the symptom is not reproduced on the same conditions.

Is the symptom reproduced?

YES>>

GO TO 3.

NO>>

Inspection End.

Diagnostic Work Sheet

DESCRIPTION

  • In general, customers have their own criteria for a problem. Therefore, it is important to understand the symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.

  • In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.

INTERVIEW SHEET SAMPLE

Interview sheet
Customer nameMR/MSRegistration numberInitial year registration
Nissan Pathfinder Vehicle typeVIN
Storage dateEngine/traction MotorMileageMile (km)
Symptom □ Does not operate ( ) function

□ Warning lamp turns ON.

□ □ □ □

□ Other (
)
□ Noise (Location: ) □ Vibration (Location: )
□ Other ( )
First occurrence □ Recently □ Other ( )
Frequency of occurrence □ Always □ Under a certain conditions of □ Sometimes ( time(s)/day)
Climate conditions □ Irrelevant
Weather □ Fine □ Cloud □ Rain □Snow □ Others ( )
Temperature □ Hot □Warm □ Cool □ Cold □ Temperature [Approx. °F (°C)]
Relative humidity □ High □ Moderate □ Low
Road conditions □ Ordinary road □ Highway □ Mountainous road (uphill or downhill) □ Rough road
Operating condition, etc.

□ Irrelevant

□ When engine/traction motor starts □ During idling

□ During driving □ During acceleration □ At constant speed driving

□ During deceleration

□ Immediately before stop [Nissan Pathfinder Vehicle speed: Approx.MPH (km/h)]

□ During cornering (right curve or left curve)

□ When steering wheel is steered (to right or to left)
Other conditions VDC setting □ On □ Off

Use of other functions

(ex. ICC)
□ Yes □ No ( )
Presence of non-genuine parts installation □ Yes □ No ( )
Memo

Additional Service When Replacing Abs Actuator and Electric Unit (control Unit) Nissan Pathfinder 5th Gen

Work Procedure

Description

When replacing the ABS actuator and electric unit (control unit), the procedures of BEFORE REPLACEMENT and AFTER REPLACEMENT must be performed.

BEFORE REPLACEMENT

When replacing the ABS actuator and electric unit (control unit), save “Operation log”.

AFTER REPLACEMENT

After replacing the ABS actuator and electric unit (control unit), the following items must be performed:

  • ABS actuator and electric unit (control unit) programming

  • ABS actuator and electric unit (control unit) configuration

  • Air bleeding of brake fluid

  • Adjust the neutral position of steering angle sensor

  • Calibration of the decel G sensor

  • Calibration of side G sensor

  • Adjustment of rear brake caliper initialization position

  • Change of system mode

  • Actual driving 3 km or more

Work Procedure [Before Replace ABS actuator and electric unit (control unit)]

SAVE “OPERATION LOG”

CONSULT

Save “Operation Log”, according to the procedure of “Programming” in CONSULT Operation Manual.

>>
  • Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

  • After replacing the ABS actuator and electric unit (control unit), perform necessary work.

Work Procedure [After Replace ABS actuator and electric unit (control unit)]

CHECK “OPERATION LOG”

CONSULT

Check “Operation Log” saved before replacing the ABS actuator and electric unit (control unit), according to the procedure of “Programming” in CONSULT Operation Manual.

Is there an applicable Operation Log in the Saved Data List?

YES>>

GO TO 2.

NO>>

GO TO 3.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) PROGRAMMING

CONSULT

Perform ABC actuator and electric unit (control unit) programming, according to “Programming” of CONSULT Operation Manual. Refer to CONSULT Operation Manual.

  • Ignition switch: ON

  • Electric parking brake: Apply

  • Electric load: OFF

  • Brake pedal: Not depressed

  • 12V battery voltage: 12 – 13.5 V (Check the value displayed on the CONSULT screen.)

>>

GO TO 5.

READ IN ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) PART NUMBER BY “EPC LINKED”

Obtain ABS actuator and electric unit (control unit) part number by EPC (service parts catalog), according to the procedure of EPC linked in CONSULT Operation Manual. Refer to CONSULT Operation Manual.

>>

GO TO 4.

PERFORM PROGRAMMING (EPC LINKED)

CONSULT

Perform ABS actuator and electric unit (control unit) programming according to the procedure of EPC linked in CONSULT Operation Manual. Refer to CONSULT Operation Manual.

  • Ignition switch: ON

  • Electric parking brake: Apply

  • Electric load: OFF

  • Brake pedal: Not depressed

  • 12V battery voltage: 12 – 13.5 V (Check the value displayed on the CONSULT screen.)

>>

GO TO 5.

PERFORM NECESSARY WORK

  1. Perform configuration. Refer to Description.

  2. Perform air bleeding. Refer to Bleeding Brake System.

  3. Perform adjustment of steering angle sensor neutral position. Refer to Description.

  4. Perform calibration of decel G sensor. Refer to Work Procedure.

  5. Calibration of side G sensor. Refer to Work Procedure.

  6. Adjustment of rear brake caliper initialization position. Refer to Work Procedure.

  7. Perform the change of system mode. Refer to Work Procedure.

  8. Select self-diagnosis for “All DTC Reading”.

  9. Erase the memory of self-diagnosis results.

>>

End of work.

Configuration Nissan Pathfinder 2022

Description

Vehicle specification needs to be written with CONSULT because it is not written after replacing the ABS actuator and electric unit (control unit).

The configuration requires network connection. CONSULT connects to network and then it downloads the configuration data from the server. Then CONSULT writes the Nissan Pathfinder vehicle specification to the ABS actuator and electric unit (control unit).

Refer to Work Procedure.

The configuration no need to “save” configuration data from the ABS actuator and electric unit (control unit). The configuration data is always generated freshly at the server and then downloaded to the CONSULT.

Work Procedure

WRITING VEHICLE SPECIFICATION

CONSULT

Perform writing Nissan Pathfinder vehicle specification to ABS actuator and electric unit (control unit) following "Automatic Configuration" procedure of "Configuration" according to CONSULT Operation Manual.

>>

Work End.

Adjustment of Steering Angle Sensor Neutral Position Nissan Pathfinder SUV

Description

Always adjust the neutral position of steering angle sensor before driving when the following operation is performed. Refer to Work Procedure.

×: Required —: Not required

ProcedureAdjust the neutral position of steering angle sensor
Removing/ installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) ×
Removing/installing steering angle sensor ×
Replacing steering angle sensor ×
Removing/installing steering components ×
Replacing steering components ×
Removing/installing front suspension components ×
Replacing front suspension components ×
Removing/installing tire —
Replacing tire —
Tire rotation —
Adjusting front wheel alignment. ×

Work Procedure

CHECK THE VEHICLE STATUS (1)

Stop vehicle with front wheels in the straight-ahead position.

Does the Nissan Pathfinder vehicle stay in the straight-ahead position?

YES>>

GO TO 2.

NO>>

Steer the steering wheel to the straight-ahead position. Stop the Nissan Pathfinder vehicle.

ADJUST NEUTRAL POSITION OF STEERING ANGLE SENSOR

CONSULT

  1. Ignition switch ON.

  2. Select “ABS”, “Work support” and “ST ANGLE SENSOR ADJUSTMENT” in this order.

  3. Select “START”.

  4. After approximately 10 seconds, select “END”.

  5. Ignition switch OFF (Auto ACC function OFF), and then it ON again.

>>

GO TO 3.

CHECK DATA MONITOR (1)

CONSULT

  1. The Nissan Pathfinder vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  2. Select “ABS”, "Data Monitor", and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 4.

CHECK STEERING COMPONENT PARTS

Check the installation condition of steering component parts. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts. GO TO 5.

CHECK FRONT SUSPENSION COMPONENT PARTS

Check the installation condition of front suspension component parts. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts. GO TO 6.

CHECK FRONT WHEEL ALIGNMENT

Check the front wheel alignment. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Adjust the front wheel alignment. Refer to Adjustment. GO TO 7.

CHECK THE Nissan Pathfinder Vehicle STATUS (2)

Stop vehicle with front wheels in the straight-ahead position.

Does the Nissan Pathfinder vehicle stay in the straight-ahead position?

YES>>

GO TO 8.

NO>>

Steer the steering wheel to the straight-ahead position. GO TO 8.

CHECK DATA MONITOR (2)

CONSULT

  1. The Nissan Pathfinder vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  2. Select “ABS”, "Data Monitor", and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 9.

CHECK DATA MONITOR (3)

CONSULT

  1. The Nissan Pathfinder vehicle is either pointing straight ahead, or the vehicle needs to be moved.

  2. The Nissan Pathfinder vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  3. Select “ABS”, "Data Monitor", and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

CONSULT

  1. Record or print self-diagnosis results and freeze frame data (FFD).

  2. Erase self-diagnosis result of “ABS”.

Are the memories erased?

YES>>

GO TO 11.

NO>>

Check the items indicated by the self-diagnosis.

EPS LEARNING

  1. Pull the parking brake switch.

  2. Ignition switch OFF.

  3. Get out of the Nissan Pathfinder vehicle and close all doors.

  4. Wait 65 seconds.

  5. Start the engine.

>>

End of work.

Calibration of Decel G Sensor Nissan Pathfinder SUV

Description

×: Required —: Not required

ProcedureDecel G sensor calibration
Removing/ installing ABS actuator and electric unit (control unit) ×
Replacing ABS actuator and electric unit (control unit) ×
Removing/installing steering components —
Replacing steering components —
Removing/installing front suspension components —
Replacing front suspension components —
Removing/installing tire —
Replacing tire —
Tire rotation —
Adjusting front wheel alignment. —

Work Procedure

CHECK THE VEHICLE STATUS

  1. Steer the steering wheel to the straight-ahead position. Stop the Nissan Pathfinder vehicle on level surface.

  2. Stop the engine.

  3. Ignition OFF (Auto ACC function OFF).

Is the Nissan Pathfinder vehicle stopped in the straight-ahead position on level surface?

YES>>

GO TO 2.

NO>>

Steer the steering wheel to the straight-ahead position. Stop the Nissan Pathfinder vehicle on level surface.

PERFORM DECEL G SENSOR CALIBRATION

CONSULT

  1. Ignition switch ON.

  2. Select “ABS”, “Work support”, “DECEL G SENSOR CALIBRATION” in this order.

  3. Select “START”.

  4. After approximately 10 seconds, select “END”.

  5. Ignition OFF (Auto ACC function OFF) and then it ON again.

>>

GO TO 3.

CHECK DATA MONITOR

CONSULT

  1. Drive the Nissan Pathfinder vehicle. Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.

  2. Select “ABS”, "Data Monitor", and “Decel G sensor” in this order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

CONSULT

Erase self-diagnosis result of “ABS”.

Are the memories erased?

YES>>

End of work.

NO>>

Check the items indicated by the self-diagnosis.

Adjustment of Brake Caliper Initial Position Nissan Pathfinder SUV

Description

×: Required —: not required

ProcedureINITIALIZATION POSITION ADJUSTMENT
Removing/ installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) ×
Removing/ installing rear brake pad (When not pressing piston of rear brake caliper assembly) —
Removing/ installing rear brake pad (When pressing piston of rear brake caliper assembly) —
Replacing rear brake pad ×
Removing/ installing rear brake caliper assembly —
Replacing rear brake caliper assembly ×
Removing/ installing parking brake switch —
Replacing parking brake switch —

Work Procedure

PERFORM INITIALIZATION POSITION ADJUSTMENT

  1. Select "ABS", "Work support", and "INITIALIZATION POSITION ADJUSTMENT" according to this order.

  2. Press "START".

>>

GO TO 2.

PERFORM THE SELF-DIAGNOSIS

With CONSULT

  1. Ignition OFF (Auto ACC function OFF) to ON.

  2. Erase self-diagnosis results memory of "ABS".

  3. Pull parking brake switch to activate electric parking brake.

  4. Push parking brake switch to release electric parking brake.

  5. Select self-diagnosis for “ABS”.

Is malfunction detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

Inspection End.

Removal/replacement of Rear Brake Pad or Rear Brake Caliper Nissan Pathfinder R53

Description

×: Required —: not required

Procedure
  • START BRAKE PAD REPLACEMENT

  • FINISH BRAKE PAD REPLACEMENT

  • INITIALIZATION POSITION ADJUSTMENT

Removing/installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) —
Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly) —
Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly) ×
Replacing rear brake pad ×
Removing/installing rear brake caliper assembly —
Replacing rear brake caliper assembly ×
Removing/installing parking brake switch —
Replacing parking brake switch —

Work Procedure

BEFORE REMOVAL/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY

CONSULT

  1. Ignition OFF (Auto ACC function OFF) to ON.

  2. Select “ABS”, “Work support”, and “START BRAKE PAD REPLACEMENT” according to this order.

  3. Touch “START”.

>>

GO TO 2.

REMOVAL AND INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR BRAKE CALIPER ASSEMBLY

Replace the rear brake pad or rear brake caliper.

  • Rear brake pad: Refer to Removal and Installation.

  • Rear brake caliper assembly: Refer to Removal and Installation.

>>

GO TO 3.

AFTER INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY

CONSULT

  1. Select “ABS”, “Work support”, and “FINISH BRAKE PAD REPLACEMENT” according to this order.

  2. Touch “START”.

>>

GO TO 4.

PERFORM INITIALIZATION POSITION ADJUSTMENT

CONSULT

  1. Select “ABS”, “Work support”, and “INITIALIZATION POSITION ADJUSTMENT” according to this order.

  2. Touch “START”.

>>

GO TO 5.

PERFORM THE SELF-DIAGNOSIS

CONSULT

  1. Pull parking brake switch to activate electric parking brake.

  2. Push parking brake switch to release electric parking brake.

  3. Select self-diagnosis for “ABS”.

Is malfunction detected?

YES>>

Check the DTC. Refer to DTC Index. GO TO 6.

NO>>

GO TO 6.

CHECK DATA MONITOR

CONSULT

Select “ABS”, “Data Monitor”, “BR FORCE EST (LH)” and “BR FORCE EST (RH)” according to this order. Check that signals are within the specified value. Refer to Reference Value.

Is the check result normal?

YES>>

GO TO 7.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

CONSULT

  1. Ignition OFF (Auto ACC function OFF) to ON.

  2. Erase self-diagnosis results memory of “ABS”.

Is the memory erased?

YES>>

Inspection End.

NO>>

Check the items indicated by the self-diagnosis.

Change of System Mode Nissan Pathfinder 5th Gen

Description

×: Required —: not required

ProcedureSYSTEM MODE CHANGE
Removing/installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) ×
Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly) —
Replacing rear brake caliper assembly —
Removing/installing parking brake switch —
Replacing parking brake switch —

Work Procedure

  • Replacing ABS actuator and electric unit (control unit)

CHANGE OF SYSTEM MODE

CONSULT

  1. Select “ABS”, “WORK SUPPORT”, and “SYSTEM MODE CHANGE” according to this order.

  2. Touch “START”.

  3. Check display item “FACTORY MODE”.

Is the inspection result “Off”?

YES>>

GO TO 2.

NO>>

Perform change of system mode again.

PERFORM THE SELF-DIAGNOSIS

CONSULT

  1. Pull parking brake switch to activate electric parking brake.

  2. Push parking brake switch to release electric parking brake.

  3. Perform self-diagnosis for “ABS”.

Is malfunction detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

Inspection End