Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature)

In this manual: Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
143steps
~858min
5/5difficulty
Done 0 of 143
  • P06da Engine Oil Pressure Control Solenoid Valve
  • P06dd Variable Oil Pressure Valve
  • P06e6 Internal Control Module
  • P0719 Brake Pedal Switch B
  • P0850 Pnp Switch
  • P1140 Intake Camshaft Position Sensor
  • P1148 Closed Loop Control
  • P1197 Out of Gas
  • P119a Fuel Rail Pressure Sensor
  • P1217 Engine Over Temperature

P06da Engine Oil Pressure Control Solenoid Valve Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P06DA 00

ENGINE OIL PRESSURE CONTROL

(Engine oil pressure control circuit/open)
Diagnosis condition —
Signal (terminal) Engine oil pressure control solenoid valve signal
Threshold A voltage signal from engine oil pressure control solenoid valve is around 0 V or more and less than normal operating voltage
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Harness or connectors (Engine oil pressure control solenoid valve circuit is open or shorted.)

  • Engine oil pressure control solenoid valve

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Maintain engine speed at 4,500 rpm or more for at least 5 seconds.

  3. Check DTC.

Is DTC P06DA detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect engine oil pressure control solenoid valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between engine oil pressure control solenoid valve harness connector and ground.

    +−Voltage
    Engine oil pressure control solenoid valve
    ConnectorTerminal
    F90 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between engine oil pressure control solenoid valve harness connector and ECM harness connector.

    Engine oil pressure control solenoid valveECMContinuity
    ConnectorTerminalConnectorTerminal
    F90 2 F79 142 Existed
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE

Check the engine oil pressure control solenoid valve. Refer to Component Inspection (Engine Oil Pressure Control Solenoid Valve).

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace engine oil pressure control solenoid valve. Refer to Exploded View.

Component Inspection (Engine Oil Pressure Control Solenoid Valve)

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE-I

  1. Turn ignition switch OFF.

  2. Disconnect engine oil pressure control solenoid valve harness connector.

  3. Check resistance between engine oil pressure control solenoid valve terminals as follows.

    Engine oil pressure control solenoid valveConditionResistance
    Terminal
    1 2 Temperature [°C (°F)] 20 (68) 19.44 – 23.76 Ω
    1 Ground

    ∞Ω

    (Continuity should not exist)
    2

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace engine oil pressure control solenoid valve. Refer to Exploded View.

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE-II

  1. Remove engine oil pressure control solenoid valve. Refer to Exploded View.

  2. Provide 12 V DC between engine oil pressure control solenoid valve terminals 1 and 2, and then interrupt it. Make sure that the plunger moves as shown in the figure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace engine oil pressure control solenoid valve. Refer to Exploded View.

P06dd Variable Oil Pressure Valve Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P06DD 00

Engine oil pressure control

(High pressure stuck diagnosis)
Diagnosis condition
  • Engine running (At 4000 rpm or less at low load)

  • low oil pressure control

A. Engine speed 1450 - 3000 rpm [engine oil temperature 30 °C ]

B. Engine speed 2050 - 3000 rpm [engine oil temperature 50 °C ]

C. Engine speed 2550 - 3000 rpm [engine oil temperature 80 °C ]
Signal (terminal) —
Threshold More than 2.1 V
Diagnosis delay time 9 seconds

POSSIBLE CAUSE

  • Engine oil pressure control solenoid valve

  • Foreign matter caughtat engine oil pressure control solenoid valve

  • Decrease in engine oil pressure

  • Decrease in engine oil level

  • Engine oil condition

  • EOP sensor

  • Cause of engine oil consumption

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Others Fixes engine oil pressure control solenoid valve in the high oil pressure control position

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  3. Maintain the following conditions for at least 9 consecutive seconds.

ENG SPEED

A. Engine speed 1450 - 3000 rpm [engine oil temperature 30 °C ]

B. Engine speed 2050 - 3000 rpm [engine oil temperature 50 °C ]

C. Engine speed 2550 - 3000 rpm [engine oil temperature 80 °C ]
COOLAN TEMP/S

A. 30 °C

B. 50 °C

C. 80 °C
Selector lever P or N position
Driving location Under low load

Is DTC P06DD detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

INSPECTION END

DTC Diagnosis Procedure

CHECK ENGINE OIL LEVEL

Check engine oil level. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE

Check the engine oil pressure control solenoid valve. Refer to Component Inspection (Engine Oil Pressure Control Solenoid Valve).

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace engine oil pressure control solenoid valve. Refer to Removal and Installation.

CHECK EOP SENSOR

Check EOP sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

P06e6 Internal Control Module Nissan Pathfinder

DTC Description

DESCRIPTION

ECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the short-circuited sensor.

Sensor power supply 1

  • APP sensor 1

  • Crankshaft position sensor 1

  • Exhaust camshaft position sensor (bank 1)

  • Throttle position sensor

  • Mass air flow sensor

  • Intake camshaft position sensor (bank 1)

  • Engine oil pressure sensor

Sensor power supply 2

  • APP sensor 2

  • Intake camshaft position sensor (bank2)

  • Refrigerant pressure sensor

  • Crankshaft position sensor 2

  • Exhaust camshaft position sensor (bank 2)

  • Fuel rail pressure sensor

Sensor power supply 3

  • EVAP control system pressure sensor

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P06E6 11

Internal control module

(Internal Control Module Knock/Combustion Vibration Sensor Processor 1 Performance)
Diagnosis condition Ignition switch ON
Signal ―
12 Threshold Malfunction in the sensor power supply voltage of ECM internal circuit
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Harness or connectors (EVAP control system pressure sensor is shorted. )

  • EVAP control system pressure sensor

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 second.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Repeat step 1 and 2 for 2 times.

  4. Turn ignition switch ON.

  5. Check the DTC.

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Perform trouble diagnosis for ECM power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT-1

  1. Turn ignition switch OFF.

  2. Disconnect EVAP control system pressure sensor harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between EVAP control system pressure sensor harness connector and ground.

    +-

    Voltage

    (Approx.)
    EVAP control system pressure sensor
    ConnectorTerminal
    B36 3 Ground 5V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 3.

CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR SUPPLY CIRCUIT-2

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.

    ++Continuity
    EVAP control system pressure sensorECM
    ConnectorTerminalConnectorTerminal
    B36 3 E32 177 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair open circuit.

CHECK SENSOR POWER SUPPLY 3 CIRCUIT

  1. Disconnect following sensors harness connector.

  2. Check harness for short to power and short to ground, between the following terminals.

ECMSensor
ConnectorTerminalNameConnectorTerminal
B36 3 EVAP control system pressure sensor E32 177

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair short to ground or short to power in harness or connectors.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

Is the 1st trip DTC P06E6 displayed again?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

P0719 Brake Pedal Switch B Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0719 00

Brake pedal switch B

(Brake Switch "B" Circuit Low)
Diagnosis condition
  • When a deceleration G of -0.13 G or more occurs after the Nissan Pathfinder vehicle speed exceeds 30 km/h.

  • When the brake normal close switch (Brake pedal position switch) is pressed.

Signal (terminal) CAN communication signal
Threshold The stop lamp switch is released until 2 seconds have passed after the Nissan Pathfinder vehicle has stopped when the diagnosis condition is established. Malfunction is confirmed when the above condition is established 5 times.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Stop lamp switch circuit is open.)

  • Stop lamp switch (BCM)

FAIL-SAFE

Not applicable

CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 2 seconds.

  2. Repeat the following step 5 times.

    1. Drive the Nissan Pathfinder vehicle and accelerate to 48 km/h.

    2. Decelerate from 48 km/h to 0 km/h within 7 seconds.

    3. Stop the Nissan Pathfinder vehicle for 2 seconds or more.

  3. Check DTC.

Is DTC P0719 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM BCM DIAGNOSIS

Perform BCM diagnosis. Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

REPLACE ECM

Replace ECM. Refer to Removal and Installation.

>>

INSPECTION END

P0850 Pnp Switch Nissan Pathfinder SUV

DTC Description

When the selector lever position is P or N, park/neutral position (PNP) signal from the TCM is sent to ECM.

ECM detects the position because the continuity of the line (the ON signal) exists.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0850 00

P-N POS SW/CIRCUIT

(Park/Neutral switch input circuit)
Diagnosis condition —
Signal (terminal) Park/neutral position (PNP) signal
Threshold The signal of the park/neutral position (PNP) signal does not change during driving after the engine is started
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

  • Transmission range switch

  • TCM

  • Electric shift control module

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0850 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

CHECK PNP SIGNAL

With CONSULT

  1. Turn ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”>>“P/N POSI SW”.

  3. Check the “P/N POSI SW” signal under the following conditions.

    Position (Selector lever)Known-good signal
    N or P position ON
    Except above position OFF

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Proceed to Diagnosis Procedure.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  2. Start engine and warm it up to normal operating temperature.

  3. Maintain the following conditions for at least 50 consecutive seconds.

    ENG SPEED 950 – 6,375 rpm
    COOLAN TEMP/S More than 66 °C
    B/FUEL SCHDL 3.0 – 31.8 msec
    VHCL SPEED SE More than 64 km/h
    Selector lever Suitable position
  4. Check 1st trip DTC.

Is DTC P0850 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0850 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index

NO>>

GO TO 2.

CHECK DTC WITH TCM

Check DTC with TCM. Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform trouble shooting relevant to DTC indicated.

CHECK DTC WITH ELECTRIC SHIFT CONTROL MODULE

Check DTC with electric shift control module. Refer to DTC Index.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Perform trouble shooting relevant to DTC indicated.

P1140 Intake Camshaft Position Sensor Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1140 00

INTK TIM S/CIRC-B1

(Intake timing sensor circuit bank 1)
A Diagnosis condition Engine running at idle
Signal (terminal) Intake camshaft position sensor (bank 1) signal
Threshold Intake camshaft position sensor signal is not inputted to ECM
Diagnosis delay time 1 second or more
B Diagnosis condition Engine running at idle
Signal (terminal) Intake camshaft position sensor (bank 1) signal
Threshold Intake camshaft position sensor signal is inappropriate or partly missing
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Harness or connectors [Intake camshaft position sensor (bank 1) circuit is open or shorted.]

  • Intake camshaft position sensor (bank 1)

  • Intake camshaft (bank 1) (sensor rotor)

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle at least 10 seconds.

  2. Check DTC.

Is DTC P1140 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK INTAKE CAMSHAFT POSITION (CMP) SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect CMP sensor (bank 1) harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between intake CMP sensor (bank 1) harness connector and ground.

    +−

    Voltage

    (Approx.)
    Intake CMP sensor (bank 1)
    ConnectorTerminal
    F113 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK INTAKE CMP SENSOR (BANK 1) POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect ECM harness connector.

  3. Check the continuity between intake CMP sensor (bank 1) harness connector and ECM harness connector.

    Intake CMP sensor (bank 1)ECMContinuity
    ConnectorTerminalConnectorTerminal
    F113 1 F78 40 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK INTAKE CMP SENSOR (BANK 1) GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between intake CMP sensor (bank 1) harness connector and ECM harness connector.

    Intake CMP sensor (bank 1)ECMContinuity
    ConnectorTerminalConnectorTerminal
    F113 2 F78 27 Existed
  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK INTAKE CMP SENSOR (BANK 1) INPUT SIGNAL CIRCUIT

  1. Check the continuity between intake CMP sensor (bank 1) harness connector and ECM harness connector.

    Intake CMP sensor (bank 1)ECMContinuity
    ConnectorTerminalConnectorTerminal
    F113 3 F78 36 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK INTAKE CMP SENSOR (BANK 1)

Check intake CMP sensor (bank 1). Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace intake CMP sensor (bank 1). Refer to Exploded View.

CHECK INTAKE CAMSHAFT (BANK 1)

Check the following items:

  • Accumulation of debris to the signal plate intake camshaft (bank 1) rear end

  • Chipping signal plate of camshaft rear end

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Remove debris and clean the signal plate of the camshaft rear end or replace the camshaft. Refer to Exploded View.

P1148 Closed Loop Control Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1148 00

CLOSED LOOP-B1

(Closed loop bank 1)
Diagnosis condition —
Signal (terminal) —
Threshold The closed loop control function for bank 1 does not operate even when Nissan Pathfinder vehicle is being driven in the specified condition
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors [A/F sensor 1 (bank1) circuit is open or shorted.]

  • A/F sensor 1 (bank 1)

  • A/F sensor 1 (bank 1) heater

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1148 is displayed with DTC for A/F sensor 1, first perform the confirmation procedure (trouble diagnosis) of DTC corresponding to A/F sensor 1.

Is applicable DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1148 is displayed with DTC for A/F sensor 1, first perform the confirmation procedure (trouble diagnosis) of DTC corresponding to A/F sensor 1.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

INSPECTION END

P1197 Out of Gas Nissan Pathfinder R53

DTC Description

This diagnosis result is detected when the fuel level of the fuel tank is extremely low and the engine does not run normally.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1197 00

FUEL RUN OUT

(Out of gas)
Diagnosis condition —
Signal (terminal) —
Threshold
  • Fuel rail pressure remains at 1.1 MPa (11.2 kg/cm2, 159.5 psi) or less with the fuel level too low

  • Fuel rail pressure remains 2.7 MPa (27.5 kg/cm2, 392 psi) lower than a target fuel pressure with the fuel level too low

Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Out of gas

  • Harness or connectors (Low pressure fuel pump circuit is open or shorted.)

  • Low pressure fuel pump

  • Harness or connectors (High pressure fuel pump circuit is shorted.)

  • Fuel pressure regulator

  • Low pressure fuel system

  • High pressure fuel pump

  • High pressure fuel pump power supply circuit

  • High pressure fuel system

  • Fuel rail pressure sensor

  • Disconnection of the fuel hose

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

DTC Confirmation Procedure

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE-I

Start the engine.

Does the engine start?

YES>>

GO TO 3.

NO>>

Proceed to Diagnosis Procedure.

PERFORM DTC CONFIRMATION PROCEDURE-II

  1. Warm up the engine to the normal operating temperature.

  2. Keep the engine speed at 3,500 rpm for 5 seconds and let it idle at least 60 seconds.

  3. Check the 1st trip DTC.

Is DTC P1197 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REFUEL THE VEHICLE

  1. Refuel 10 liter (10 US qt, 8 imp qt).

  2. Start the engine and keep the engine speed at 3,000 rpm for 30 seconds.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Turn ignition switch ON.

  5. Turn ignition switch OFF and wait at least 10 seconds.

  6. Turn ignition switch ON.

  7. Erase the DTC.

  8. Start the engine and let it idle at least 60 seconds.

  9. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC P1197 detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK LOW PRESSURE FUEL PUMP

Check low pressure fuel pump. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK HIGH PRESSURE FUEL PUMP CONTROL CIRCUIT

Check high pressure fuel pump control circuit. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK ECM POWER SUPPLY CIRCUIT

Check ECM power supply circuit. Refer to Diagnosis Procedure.

Is inspection result normal?

YES>>

Check the fuel hose for disconnection and looseness.

NO>>

Repair or replace error-detected parts.

P119a Fuel Rail Pressure Sensor Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P119A 00

FUEL PRESSURE SENSOR

(Fuel pressure sensor)
Diagnosis condition
  • Battery voltage: 8 V or more

  • Under engine start condition

  • Engine coolant temperature at previous ignition switch OFF: 65 °C or more

  • Engine coolant temperature: 35 °C or less

  • Temperature difference between engine coolant and intake air: Less than 6 °C

  • Fuel system monitor: Excessively RICH

Signal (terminal) Fuel rail pressure sensor signal
Threshold Fuel rail pressure is less than 1.0 MPa (10.2 kg/cm2, 145 psi) (calculated by ECM)
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    • The fuel rail pressure sensor circuit is open or shorted.

    • Sensor power supply 2 is shorted.

  • Fuel rail pressure sensor

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

DTC Confirmation Procedure

PRECONDITIONING-I

If DTC Confirmation Procedure is previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, check that battery voltage is 9 V or more with ignition switch ON.

>>

GO TO 2.

PRECONDITIONING-II

  1. Start the engine and warm it up until engine coolant temperature reaches 70 °C or more.

  2. Stop the engine and leave the Nissan Pathfinder vehicle in a cool place (soak the engine) until the engine coolant temperature reaches 35 °C or less.

Are the conditions satisfied?

YES>>

GO TO 4.

NO>>

GO TO 3.

COMPONENT FUNCTION CHECK

With CONSULT

  1. Turn ignition switch OFF.

  2. Start the engine.

  3. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  4. Check the value of “FUEL PRES SEN V” under the following conditions.

    Monitor Item Condition Values/Status
    FUEL PRES SEN V Engine speed: Idle 1.120 – 1.310 V
    Engine speed: Revving engine from idle to 4,000 rpm quickly 1.120 – 2.900 V

Without CONSULT

  1. Turn ignition switch OFF.

  2. Start the engine.

  3. Check fuel rail pressure sensor signal voltage.

ECM Condition Voltage
Connector + −
Terminal
F78 47 85 Engine speed: Idle 1.12 – 1.31 V
Engine speed: Revving engine from idle to 4,000 rpm quickly 1.12 – 2.90 V

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

PERFORM DTC CONFIRMATION PROCEDURE-I

With CONSULT

  1. Turn ignition switch ON (engine stopped).

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”>>“COOLAN TEMP/S” and “INT/A TEMP SE”.

  3. Check that the indicated value of “COOLAN TEMP/S” is less than 35 °C.

  4. Check that the difference between “INT/A TEMP SE” and “COOLAN TEMP/S” is 5 °C or less.

  5. Check “Self-diagnostic result” of “ENGINE”.

Is DTC P119A detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

Conditions satisfied: GO TO 5.

NO-2>>

Conditions not satisfied: GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE-II

  1. Start the engine (or cranking) at least 1 second.

  2. Check “Self-diagnostic result” of “ENGINE”.

Is DTC P119A detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK FUEL RAIL PRESSURE (FRP) SENSOR POWER SUPPLY-I

  1. Turn ignition switch OFF.

  2. Disconnect FRP sensor connector.

  3. Turn ignition switch ON.

  4. Check the voltage between FRP sensor harness connector terminals.

    FRP sensor

    Voltage

    (Approx.)
    Connector + −
    terminal
    F97 3 1 5 V

Inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 2.

CHECK FRP SENSOR POWER SUPPLY-II

Check the voltage between FRP sensor harness connector and the ground.

+ −

Voltage

(Approx.)
FRP sensor
Connector Terminal
F97 3 Ground 5 V

Is inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 3.

CHECK FRP SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between FRP sensor harness connector and ECM harness connector.

    FRP sensor ECM Continuity
    Connector Terminal Connector Terminal
    F97 3 F78 66 Existed
  4. Also check harness for short to power and short to ground.

Is inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Perform Diagnosis Procedure.

Is inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

CHECK FRP SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between FRP sensor harness connector and ECM harness connector.

    FRP sensor ECM Continuity
    Connector Terminal Connector Terminal
    F97 1 F78 85 Existed
  4. Also check harness for short to power.

Is inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK ECM GROUND CIRCUIT

  1. Check the continuity between ECM harness connector and ground.

    ECM — Continuity
    Connector Terminal
    F78 3 Ground Existed
    F79 87
    E32 199
    201
    204
  2. Also check harness for short to power.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

CHECK FRP SENSOR SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between FRP sensor harness connector and ECM harness connector.

    FRP sensor ECM Continuity
    Connector Terminal Connector Terminal
    F97 2 F78 47 Existed
  4. Also check harness for short to power and short to ground.

Is inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK FRP SENSOR

Check the FRP sensor. Refer to Component Inspection (Fuel Rail Pressure Sensor).

Is inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

Component Inspection (Fuel Rail Pressure Sensor)

CHECK FRP SENSOR

With CONSULT

  1. Turn ignition switch OFF.

  2. Reconnect harness connector disconnected.

  3. Start engine.

  4. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  5. Check that the “FUEL PRES SEN V” indication.

    Monitor Item Condition Values/Status
    FUEL PRES SEN V Engine speed: Idle 1.120 – 1.310 V
    Engine speed: Revving engine from idle to 4,000 rpm quickly 1.120 – 2.900 V

Without CONSULT

  1. Turn ignition switch OFF.

  2. Reconnect harness connector disconnected.

  3. Start the engine.

  4. Check FRP sensor signal voltage.

ECM Condition Voltage
Connector + −
Terminal
F78 47 85 Engine speed: Idle 1.12 – 1.31 V
Engine speed: Revving engine from idle to 4,000 rpm quickly 1.12 – 2.90 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace FRP sensor. Refer to Exploded View.

P1217 Engine Over Temperature Nissan Pathfinder R53

DTC Description

If the cooling fan or another component in the cooling system malfunctions, engine coolant temperature will rise.

When the engine coolant temperature reaches an abnormally high temperature condition, a malfunction is indicated.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1217 00

ENG OVER TEMP

[Engine over temperature (Overheat)]
Diagnosis condition —
Signal (terminal) —
Threshold
  • Cooling fan does not operate properly (Overheat).

  • Cooling fan system does not operate properly (Overheat).

  • Engine coolant was not added to the system using the proper filling method.

  • Engine coolant is not within the specified range.

Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (Cooling fan circuit is open or shorted.)

  • IPDM E/R

  • Cooling fan control module

  • Cooling fan motor

  • Radiator hose

  • Radiator

  • Radiator cap

  • Water pump

  • Thermostat

  • Engine coolant temperature sensor

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1217 is displayed with DTC UXXXX or P0607, first perform the confirmation procedure (trouble diagnosis) for DTC UXXXX or P0607.

Is DTC UXXXX or P0607 detected?

YES>>

Perform diagnosis of applicable.

  • DTC UXXXX: Refer to DTC Index.

  • DTC P0607: Refer to DTC Description.

NO>>

GO TO 2.

PERFORM COMPONENT FUNCTION CHECK-I

Check the coolant level in the reservoir tank and radiator.

Allow engine to cool before checking coolant level.

Is the coolant level in the reservoir tank and/or radiator below the proper range?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM COMPONENT FUNCTION CHECK-II

Confirm whether customer filled the coolant or not.

Did customer fill the coolant?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 4.

PERFORM COMPONENT FUNCTION CHECK-III

With CONSULT

  1. Turn ignition switch ON.

  2. Perform “FAN DUTY CONTROL” in “Active Test” mode of “ENGINE”.

  3. Make sure that cooling fan speed varies according to the percentage.

Without CONSULT

Perform IPDM E/R auto active test and check cooling fan motors operation, refer to CONSULT Function (IPDM E/R).

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1217 is displayed with DTC UXXXX or P0607, first perform the confirmation procedure (trouble diagnosis) for DTC UXXXX or P0607.

Is DTC UXXXX or P0607 detected?

YES>>

Perform diagnosis of applicable.

  • DTC UXXXX: Refer to DTC Index.

  • DTC P0607: Refer to DTC Description.

NO>>

GO TO 2.

CHECK COOLING FAN OPERATION

With CONSULT

  1. Turn ignition switch ON.

  2. Perform “FAN DUTY CONTROL” in “Active Test” mode of “ENGINE”.

  3. Make sure that cooling fan speed varies according to the percentage.

Without CONSULT

  1. Perform IPDM E/R auto active test and check cooling fan motors operation, refer to CONSULT Function (IPDM E/R).

  2. Make sure that cooling fan operates.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Proceed to Diagnosis Procedure (Cooling Fan Motor).

CHECK COOLING SYSTEM FOR LEAK-I

Check cooling system for leak. Refer to System Inspection.

Is leakage detected?

YES>>

GO TO 4.

NO>>

GO TO 5.

CHECK COOLING SYSTEM FOR LEAK-II

Check the following for leak.

  • Hose

  • Radiator

  • Water pump

>>

Repair or replace malfunctioning part.

CHECK RADIATOR CAP

Check radiator cap. Refer to System Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace radiator cap. Refer to Exploded View.

CHECK THERMOSTAT

Check thermostat. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace thermostat assembly. Refer to Removal and Installation.

CHECK ENGINE COOLANT TEMPERATURE SENSOR

Check engine coolant temperature sensor. Refer to Component Inspection (Engine Coolant Temperature Sensor).

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Replace engine coolant temperature sensor. Refer to Exploded View.

OVERHEATING CAUSE ANALYSIS

If the cause cannot be isolated, check the Troubleshooting Chart.

>>

INSPECTION END