Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function)

In this manual: Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
127steps
~762min
5/5difficulty
Done 0 of 127
  • P1575 Brake Switch
  • P159f Active Grille Shutter
  • P1603 Ecm
  • P161d Immobilizer
  • P1650 Starter Motor Relay 2
  • P1800 Vias Control Solenoid Valve 1
  • P1805 Stop Lamp Switch
  • P1a10 Ecm Initial Learning Incomplete
  • P2100 Throttle Control Motor Relay
  • P2101 Electric Throttle Control Function

P1575 Brake Switch Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detecting condition
P1575 00

BRAKE SW

(BRAKE SW)
Diagnosis condition —
Signal (terminal) CAN communication signal
Threshold Stop lamp switch signal is sent to ECM for extremely long time while the Nissan Pathfinder vehicle is being driven.
Diagnosis delay time —

POSSIBLE CAUSE

Stop lamp switch (BCM)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

COMPONENT FUNCTION CHECK

With CONSULT

  1. Turn ignition switch ON.

  2. Select “DATA MONITOR” mode of “ENGINE” with CONSULT.

  3. Check that the “BRAKE SW 2” indication as per the following condition.

    Monitor itemConditionIndication
    BRAKE SW 2 Brake pedal Fully released OFF
    Slightly depressed ON

Without CONSULT

  1. Turn ignition switch OFF.

  2. Check the stop lamp when depressing and releasing the brake pedal.

    Brake pedalStop lamp
    Fully released Not illuminated
    Slightly depressed Illuminated

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO-2>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

Diagnosis Procedure

PERFORM BCM DIAGNOSIS

Perform BCM diagnosis. Refer to DTC Index.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

P159f Active Grille Shutter Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

Active grille shutter normally stops within zone which is defined by zone (90°±10°).

If the active grille shutter stops within zone stuck error is detected, and if the active grille shutter stops at position beyond zone overrun error is detected.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P159F 00

ACTIVE GRILLE AIR SHUTTER A

(Active grille air shutter A)
Diagnosis condition —
Signal (terminal) —
Threshold Detects the malfunction of initial position learning or operational malfunctions for specified times.
Diagnosis delay time —

POSSIBLE CAUSE

Foreign objects interferes with active grille shutter

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P159F is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If another DTC Confirmation Procedure is conducted just before this procedure, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is between 11V and 16V with ignition switch ON.

With CONSULT >>

GO TO 3.

Without CONSULT>>

GO TO 5.

DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch OFF and wait 10 seconds or more.

  2. Turn ignition switch ON.

  3. Select “ACTIVE GRILLE SHUTTER” in “ACTIVE TEST”of “ENGINE” using CONSULT.

  4. Touch “CALIBRTN” and wait at least 30 seconds.

  5. Check the 1st trip DTC.

Is 1st trip DTC is detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

GO TO 4.

CHECK THE OPERATION OF ACTIVE GRILLE SHUTTER

After the calibration completes, check the operation of active grille shutter as follows.

ConditionActive grille shutter
Select "CLOSE" Open → Close
Select "OPEN" Close→ Open

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Proceed to DTC Diagnosis Procedure.

DTC CONFIRMATION PROCEDURE

  1. Drive the Nissan Pathfinder vehicle at 30 km/h or more for at least 30 seconds.

  2. Check DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P159F is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ACTIVE GRILL SHUTTER

  1. Turn ignition switch OFF.

  2. Check if any foreign objects interferes with active grille shutter.

  3. Check the installation condition of active grille shutter.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace the error-detected parts.

P1603 Ecm Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1603 00

CONTROL MODULE

(CONTROL MODULE)
Diagnosis condition —
Signal (terminal) —
Threshold EEPROM (built-in microcomputer) system internal ECM does not function properly
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

Perform the following procedure before performing DTC Confirmation Procedure.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and wait at least 10 seconds.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Repeat steps 1 and 2 for 4 times.

  4. Turn ignition switch ON.

  5. Erase DTC.

  6. Turn ignition switch OFF and wait at least 10 seconds.

  7. Start the engine and wait for 10 seconds.

  8. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

INSPECTION START

Check that the battery negative terminal is not disconnected during ignition switch ON.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

ERASE DTC

  1. Start the engine and let it idle at least 10 seconds.

  2. Turn ignition switch OFF.

  3. Repeat steps 1 and 2 for 4 times.

  4. Erase DTC.

  5. Turn ignition switch OFF and wait at least 10 seconds.

  6. Start the engine and let it idle for 10 seconds.

  7. Check 1st trip DTC.

Is DTC P1603 detected again?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Check ECM power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

Is the DTC P1603 detected again?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

P161d Immobilizer Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

Perform the trouble diagnosis for the corresponding DTC of another ECU. Refer to DTC Description.

FAIL-SAFE

Not applicable

P1650 Starter Motor Relay 2 Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1650 00

STR MTR RELAY 2

(Starter relay circuit)
A Diagnosis condition —
Signal (terminal) CAN communication signal
Threshold Starter relay is stuck ON.
Diagnosis delay time —
B Diagnosis condition —
Signal (terminal) CAN communication signal
Threshold Starter relay power supply circuit is excessively high voltage.
Diagnosis delay time —
C Diagnosis condition —
Signal (terminal) CAN communication signal
Threshold Starter relay circuit is excessively low voltage
Diagnosis delay time —

POSSIBLE CAUSE A

  • Starter relay

  • IPDM E/R

POSSIBLE CAUSE B

  • Harness and connectors

    (Between IPDM E/R harness connector and battery is open.)

  • IPDM E/R

POSSIBLE CAUSE C

  • Harness and connectors

    (Starter relay circuit is open or shorted.)

  • IPDM E/R

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

When ECM detects error, ECM detects DTC, prohibits the start/stop system operation, and display the stop/start warning indicator.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1650 is displayed with DTC U1000 or P0607, first perform the confirmation procedure (trouble diagnosis) for DTC U1000 or P0607.

Is DTC U1000 or P0607 detected?

YES>>

Perform diagnosis of applicable.

  • DTC U1000: Refer to DTC Description.

  • DTC P0607: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If the other DTC Confirmation Procedure is performed right before this procedure, the ignition switch must be turned OFF and wait for 10 seconds or more to start this procedure.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-1

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON and wait at least 30 seconds

  3. Turn ignition switch OFF, wait at least 10 seconds and then turn ON.

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE-2

With CONSULT

  1. Start the engine and warm it up to normal operating temperature.

  2. Select “AUTO STOP START” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.

  3. Touch “START” and operate stop/start system. (engine stop.)

  4. Touch “CANCEL” and restart the engine.

Without CONSULT

Activate stop/start system. Refer to System Description.

Is stop/start system activated normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1650 is displayed with DTC U1000 or P0607, first perform the confirmation procedure (trouble diagnosis) for DTC U1000 or P0607.

Is DTC U1000 or P0607 detected?

YES>>

Perform diagnosis of applicable.

  • DTC U1000: Refer to DTC Description.

  • DTC P0607: Refer to DTC Description.

NO>>

GO TO 2.

CHECK IPDM E/R POWER SUPPLY CIRCUIT

Check IPDM E/R power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

REPLACE IPDM E/R

Replace IPDM E/R. Refer to Removal and Installation.

>>

INSPECTION END

P1800 Vias Control Solenoid Valve 1 Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1800 00

VIAS S/V CIRC-B1

(VIAS solenoid valve circuit bank 1)
Diagnosis condition Ignition switch ON
Signal (terminal) VIAS control solenoid valve 1 signal
Threshold An excessively low or high voltage signal is sent to ECM through the VIAS control solenoid valve 1
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (VIAS control solenoid valve 1 circuit is open or shorted.)

  • VIAS control solenoid valve 1

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 5 seconds.

  2. Check 1st trip DTC.

Is DTC P1800 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK VIAS CONTROL SOLENOID VALVE 1 POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect VIAS control solenoid valve 1 harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between VIAS control solenoid valve 1 harness connector and ground.

    +−Voltage
    VIAS control solenoid valve 1
    ConnectorTerminal
    F66 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK VIAS CONTROL SOLENOID VALVE 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between VIAS control solenoid valve 1 harness connector and IPDM E/R harness connector.

    VIAS control solenoid valve 1IPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    F66 1 F24 78 Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK VIAS CONTROL SOLENOID VALVE 1 OUTPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between VIAS control solenoid valve 1 harness connector and ECM harness connector.

    VIAS control solenoid valve 1ECMContinuity
    ConnectorTerminalConnectorTerminal
    F66 2 F79 163 Existed
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK VIAS CONTROL SOLENOID VALVE 1

Check VIAS control solenoid valve 1. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace VIAS control solenoid valve 1. Refer to Exploded View.

Component Inspection

CHECK VIAS CONTROL SOLENOID VALVE 1

With CONSULT

  1. Turn ignition switch OFF.

  2. Reconnect all harness connectors disconnected.

  3. Disconnect vacuum hoses connected to VIAS control solenoid valve 1.

  4. Turn ignition switch ON.

  5. On CONSULT screen, select “ENGINE”>>“Active Test”>>“VIAS S/V-1”.

  6. Check air passage continuity and operation delay time under the following conditions.

Condition

(VIAS S/V-1)
Air passage continuity between and

Air passage continuity

between and
ON Existed Not existed
OFF Not existed Existed

Without CONSULT

  1. Turn ignition switch OFF.

  2. Disconnect VIAS control solenoid valve 1 harness connector.

  3. Disconnect vacuum hoses connected to VIAS volume control solenoid valve 1.

  4. Check air passage continuity and operation delay time under the following conditions.

ConditionAir passage continuity between and

Air passage continuity

between and
12 V direct current supply between terminals 1 and 2 Existed Not existed
No supply Not existed Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace VIAS control solenoid valve 1. Refer to Exploded View.

P1805 Stop Lamp Switch Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1805 00

BRAKE SW/CIRCUIT

(Brake switch/circuit)
Diagnosis condition —
Signal (terminal) CAN communication signal
Threshold A stop lamp switch signal is not sent to ECM while the Nissan Pathfinder vehicle is driving
Diagnosis delay time —

POSSIBLE CAUSE

Stop lamp switch (BCM)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Fully depress the brake pedal for at least 5 seconds.

  3. Erase the DTC.

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM BCM DIAGNOSIS

Perform BCM diagnosis. Refer to DTC Index.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

P1a10 Ecm Initial Learning Incomplete Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1A10 00

ECM initial learning Incomplete

(ECM initial learning Incomplete)
Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold When drive distance will be less than 96 km (60 miles) and ECM keeps initial state to replace ECM will indicate DTC.
Diagnosis delay time —

POSSIBLE CAUSE

ECM initial learning not complete

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM ECM INITIAL LEARNING

  1. Turn ignition switch ON. (Do not start the engine.)

  2. Set selector lever to P position and apply parking brake.

  3. Accelerator pedal is fully depressed and erase DTC.

  4. Turn ignition switch OFF.

  5. Check that no DTC is detected.

>>

INSPECTION END

P2100 Throttle Control Motor Relay Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2100 00

ETC MOT PWR-B1

(Throttle control motor relay circuit open)
Diagnosis condition Engine running at idle
Signal (terminal) Throttle control motor relay signal
Threshold A voltage of power source for throttle control motor is excessively low
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (Throttle control motor relay circuit is open)

  • Throttle control motor relay

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V.

Which DTC is detected?

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P2100

  1. Ignition switch ON and wait at least 2 seconds.

  2. Start engine and let it idle for 5 seconds.

  3. Check DTC.

Is DTC P2100 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

INSPECTION END

Diagnosis Procedure

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY

  1. Ignition switch ON.

  2. Check the voltage between ECM harness connector and ground.

    +−Voltage
    ECM
    ConnectorTerminalConnectorTerminal
    F79 139 E32 204 Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT

  1. Disconnect ECM harness connector.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between ECM harness connector and IPDM E/R harness connector.

    ECMIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    F79 139 F24 67 Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blowing.

    LocationFuse No.Capacity
    IPDM E/R #80 15A

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

GO TO 4.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL

Check the voltage between ECM harness connector and ground as per the following conditions.

ECMCondition

Voltage

(Approx.)
+−
ConnectorTerminalConnectorTerminal
F79 95 E32 204 Ignition switch: OFF 0 V
Ignition switch: ON Battery voltage

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 5.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect IPDM E/R harness connector.

  4. Check the continuity between ECM harness connector and IPDM E/R harness connector.

    ECMIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    F79 95 F24 72 Existed
  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

P2101 Electric Throttle Control Function Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2101 00

ETC FNCTN/CIRC-B1

(Electric throttle control performance)
Diagnosis condition Engine running at idle
Signal (terminal) Throttle control motor signal
Threshold Electric throttle control function does not operate properly
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (Throttle control motor circuit is open or shorted)

  • Electric throttle control actuator

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P2101 is displayed with DTC P2100 or P2119, first perform the confirmation procedure (trouble diagnosis) for DTC P2100 or P2119.

Is DTC P2100 or P2119 detected?

YES>>

Perform diagnosis of applicable.

  • DTC P2100: Refer to DTC Description.

  • DTC P2119: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V when engine is running.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 2 seconds.

  2. Start engine and let it idle for 5 seconds.

  3. Check DTC.

Is DTC P2101 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P2101 is displayed with DTC P2100 or P2119, first perform the confirmation procedure for DTC P2100 or P2119.

Is DTC P2100 or P2119 detected?

YES>>

Perform diagnosis of applicable.

  • DTC P2100: Refer to DTC Description.

  • DTC P2119: Refer to DTC Description.

NO>>

GO TO 2.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL

Check the voltage between ECM harness connector terminals as per the following conditions.

ECM Condition

Voltage

(Approx.)
+ −
Connector Terminal Connector Terminal
F79 139 E32 204 Ignition switch: OFF 0 V
Ignition switch: ON Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 3.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect IPDM E/R harness connector.

  4. Check the continuity between ECM harness connector and IPDM E/R harness connector.

    ECM IPDM E/R Continuity
    Connector Terminal Connector Terminal
    F79 139 F24 67 Existed
  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT

  1. Check the continuity between ECM harness connector and IPDM E/R harness connector.

    ECM IPDM E/R Continuity
    Connector Terminal Connector Terminal
    F79 95 F24 72 Existed
  2. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect electric throttle control actuator harness connector.

  3. Disconnect ECM harness connector.

  4. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

    Electric throttle control actuator ECM Continuity
    Connector Terminal Connector Terminal
    F50 2 F79 148 Existed
    147 Not existed
    1 148 Not existed
    147 Existed
  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

  1. Remove air duct hose and resonator assembly. Refer to Exploded View.

  2. Check if foreign matter is caught between the throttle valve and the housing.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Remove the foreign matter and clean the electric throttle control actuator inside, then perform throttle valve closed position learning. Refer to Description.

CHECK THROTTLE CONTROL MOTOR

Check the throttle control motor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace electric throttle control actuator. Refer to Exploded View.

Component Inspection

CHECK THROTTLE CONTROL MOTOR

  1. Turn ignition switch OFF.

  2. Disconnect electric throttle control actuator harness connector.

  3. Check the resistance between electric throttle control actuator terminals as per the following.

    Electric throttle control actuator Condition Resistance
    Terminal
    1 2 Temperature [°C (°F)] 25 (77) 1 – 15 Ω

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace electric throttle control actuator. Refer to Exploded View.