4014 C1078-55 Not Configuration

In this manual: 4014 C1078-55 Not Configuration
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
146steps
~876min
5/5difficulty
Done 0 of 146
  • C1078-55 Not Configuration
  • C1082-86 Can Comm Err (tcm)
  • C1083 Steering Angle Sensor
  • C1085-86 Combination Meter
  • C10aa-63 Pump Motor
  • C10ac-54 Calibration Incomplete
  • C10af-01 Pressure Sensor
  • C10b1 Parking Brake Actuator (lh)
  • C10b2 Parking Brake Switch
  • C10b3 Parking Brake Control Module

C1078-55 Not Configuration Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1078–55

Not configuration

(Not configuration)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) -
Threshold When configuration is not complete.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
Configuration is not complete
  • Configuration is not complete

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1078-55” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

PROGRAMMING OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Perform programming of ABS actuator and electric unit (control unit). Refer to Work Procedure.

>>

GO TO 2.

CHECK SELF-DIAGNOSIS

CONSULT

Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1078-55” in self-diagnosis for “ABS”.

>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

C1082-86 Can Comm Err (tcm) Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1082–86

CAN comm err (TCM)

[Controller area network communication error (transmission control module)]
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in TCM system.
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • CAN communication line

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Harness or connector

  • CAN communication line

  • TCM

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1082-86” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK TCM SYSTEM

CONSULT

Perform self-diagnosis for “TRANSMISSION”

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK CONNECTOR AND TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect TCM harness connector.

  3. Disconnect ABS actuator and electric unit (control unit) harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect TCM harness connector.

  2. Connect ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

Inspection End

C1083 Steering Angle Sensor Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1083–86

Steering angle sensor

(Steering angle sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in steering angle sensor system.
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • CAN communication line

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Harness or connector

  • CAN communication line

  • Steering angle sensor

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1083-86” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK STEERING ANGLE SENSOR SYSTEM

CONSULT

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK CONNECTOR AND TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect steering angle sensor harness connector.

  3. Disconnect ABS actuator and electric unit (control unit) harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 3.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect steering angle sensor harness connector.

  2. Connect ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

Inspection End

C1085-86 Combination Meter Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1085–86

Combination meter

(Combination meter)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in combination meter system.
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • CAN communication line

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Harness or connector

  • CAN communication line

  • Combination meter

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1085-86” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK COMBINATION METER SYSTEM

CONSULT

Perform self-diagnosis for “METER/M&A”.

Is DTC detected?

YES>>

Check the DTC.

  • 7 inch information display: Refer to DTC Index.

NO>>

GO TO 2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK CONNECTOR AND TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect combination meter harness connector.

  3. Disconnect ABS actuator and electric unit (control unit) harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect combination meter harness connector.

  2. Connect ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

Inspection End

C10aa-63 Pump Motor Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C10AA-63

Pump motor

(Pump motor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) -
Threshold When a malfunction is detected in motor or motor relay.
Diagnosis delay time 12 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON, and wait 30 seconds.

  2. Drive the Nissan Pathfinder vehicle at approximately 50 km/h or more for approximately 2 minutes.

  3. Stop the vehicle.

  4. Ignition switch OFF (Auto ACC function OFF).

  5. Start the engine.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C10AA-63” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK CONNECTOR

  1. Disconnect 12 V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 2.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect 12 V battery negative terminal, and wait 30 seconds.

  2. Drive the Nissan Pathfinder vehicle at approximately 50 km/h or more for approximately 2 minutes.

  3. Stop the Nissan Pathfinder vehicle.

  4. Ignition switch OFF (Auto ACC function OFF).

  5. Start the engine.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C10AA-63” detected?

YES>>

GO TO 3.

NO>>

Inspection End

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT (1)

CONSULT

  1. Drive the Nissan Pathfinder vehicle at approximately 50 km/h or more for approximately 2 minutes.

  2. Stop the Nissan Pathfinder vehicle.

  3. Erase self-diagnosis result for “ABS”.

  4. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

>>

Inspection End

CHECK TERMINAL

  1. Disconnect 12 V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Repair / replace harness or connector. GO TO 6.

ERASE SELF-DIAGNOSIS RESULT (2)

CONSULT

  1. Connect 12 V battery negative terminal.

  2. Drive the Nissan Pathfinder vehicle at approximately 50 km/h or more for approximately 2 minutes.

  3. Stop the Nissan Pathfinder vehicle.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

>>

Inspection End

C10ac-54 Calibration Incomplete Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C10AC-54

Calibration incomplete

(Calibration incomplete)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) -
Threshold When calibration of yaw rate/side/decel G sensor is not complete.
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
Incomplete calibration of G sensor/yaw rate sensor
  • Incomplete calibration of G sensor/yaw rate sensor

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C10AC-54” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CALIBRATION OF DECEL G SENSOR

Perform calibration of decel G sensor. Refer to Work Procedure.

>>

GO TO 2.

CALIBRATION OF SIDE G SENSOR

Perform calibration of side G sensor. Refer to Work Procedure.

>>

GO TO 3.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C10AC-54” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

C10af-01 Pressure Sensor Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C10AF-01

Pressure sensor

(Pressure sensor)
Diagnosis condition
  • During driving below 15 km/h (no braking)

  • When the power supply voltage is normal.

Signal (terminal) Pressure sensor signal
Threshold When a malfunction is detected in pressure sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • Stop lamp switch system

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Harness or connector

  • Stop lamp switch system

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto switch OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C10AF-01” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

STOP LAMP SWITCH SYSTEM

Check the stop lamp switch system. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace stop lamp switch system.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Erase self-diagnosis result for “ABS”.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Start the engine and drive the Nissan Pathfinder vehicle for a short period of time.

  5. Stop the Nissan Pathfinder vehicle.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C10AF-01” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.

C10b1 Parking Brake Actuator (lh) Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C10B1–01

Parking brake actuator (LH)

[Parking brake actuator (left)]
Diagnosis condition When parking brake is apply or release
Signal (terminal) —
Threshold When an open circuit is detected in circuit motor of parking brake actuator (LH).
Diagnosis delay time 1 second or less
C10B1–09

Parking brake actuator (LH)

[Parking brake actuator (left)]
Diagnosis condition When parking brake is apply or release
Signal (terminal) —
Threshold When a motor of the parking brake actuator (RH) is not rotating.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • Parking brake actuator (LH)

  • Rear brake caliper assembly (LH)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • Parking brake actuator (LH)

  • Rear brake caliper assembly (LH)

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended:

Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON.

  2. Push the parking brake switch.

  3. Pull the parking brake switch.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C10B1” detected?

YES>>

"C1B1-01" only is displayed by "CRNT": Refer to DTC Diagnosis Procedure.

YES>>

"C10B1-01" and "C10B1-09" are displayed by "CRNT": Refer to DTC Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK CONNECTOR

  1. Disconnect 12 V battery negative terminal.

  2. Check the parking brake actuator (LH) harness connector for disconnection or looseness.

  3. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness or connector. GO TO 2.

CHECK PARKING BRAKE ACTUATOR CIRCUIT (1)

  1. Disconnect the ABS actuator and electric unit (control unit) harness connector.

  2. Check the continuity between ABS actuator and electric unit (control unit) harness connector terminals.

    ABS actuator and electric unit (control unit)Continuity
    ConnectorTerminals
    E125 13 12 Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK PARKING BRAKE ACTUATOR CIRCUIT (2)

Check the continuity between parking brake actuator (LH) harness connector terminals.

TerminalsContinuity
1 2 Yes

Is the inspection result normal?

YES>>

Repair/replace harness or connector.

NO>>

Replace the rear brake caliper assembly (LH). Refer to Removal and Installation.

CHECK MOTOR POWER SUPPLY

  1. Connect 12V battery negative terminal.

  2. Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.

    (+)(–)Voltage
    ABS actuator and electric unit (control unit)
    ConnectorTerminal
    E125 1 Ground Approx. 10 − 16 V

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 5.

CHECK MOTOR POWER SUPPLY CIRCUIT

  1. Disconnect 12 V battery negative terminal.

  2. Check the 60 A fuse (C).

  3. Check the continuity and short circuit between ABS actuator and electric unit (control unit) harness connector terminal (1) and 60 A fuse (C).

Is the inspection result normal?

YES>>

Perform trouble diagnosis for 12 V battery power supply.

NO>>

Repair/replace harness, connector or fuse.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT

  1. Disconnect 12 V battery negative terminal.

  2. Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.

    ABS actuator and electric unit (control unit)(–)Continuity
    ConnectorTerminal
    E125 46 Ground Yes
    14

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector. GO TO 7.

CHECK TERMINAL

  1. Check parking brake actuator (LH) terminals for damage or loose connection with harness connector.

  2. Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair/replace harness, connector or terminal. GO TO 8.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect the parking brake actuator (LH) harness connector.

  2. Connect the ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12 V battery negative terminal.

  4. Ignition switch ON.

  5. Apply and release the parking brake five times.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C10B1-01” detected?

YES>>

"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

YES>>

"PAST" is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

Inspection End

C10b2 Parking Brake Switch Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C10B2–01

Parking brake switch

(Parking brake switch)
Diagnosis condition When ignition switch is ON
Signal (terminal) Paring brake switch
Threshold When a malfunctioning in the parking brake switch circuit.
Diagnosis delay time 1 second or less
C10B2–64

Parking brake switch

(Parking brake switch)
Diagnosis condition When ignition switch is ON
Signal (terminal) Paring brake switch
Threshold When a malfunctioning in the parking brake switch circuit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • Parking brake switch

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • Parking brake switch

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON.

  2. Push the parking brake switch.

  3. Pull the parking brake switch.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C10B2” detected?

YES>>

“CRNT” is displayed: Refer to DTC Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK DATA MONITOR

CONSULT

  1. Ignition switch ON.

  2. Select “ABS”, “Data Monitor” and “PB SW” according to this order. Check that data monitor displays when parking brake switch is pull, neutral or push. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 2.

CHECK CONNECTOR

  1. Disconnect 12 V battery negative terminal.

  2. Check the parking brake switch harness connector for disconnection or looseness.

  3. Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector. GO TO 3.

CHECK PARKING BRAKE SWITCH CIRCUIT

  1. Disconnect the parking brake switch harness connector.

  2. Disconnect the ABS actuator and electric unit (control unit) harness connector.

  3. Check the continuity between ABS actuator and electric unit (control unit) harness connector and parking brake switch harness connector.

    ABS actuator and electric unit (control unit)Parking brake switchContinuity
    ConnectorTerminalConnectorTerminal
    E125 34 M210 9 Yes
    31 7
    16 6
    32 5
    15 3

  4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.

    ABS actuator and electric unit (control unit)(–)Continuity
    ConnectorTerminal
    E125 34 Ground No
    31
    16
    32
    15

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness or connector. GO TO 4.

CHECK PARKING BRAKE SWITCH

Check the parking brake switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace the parking brake switch. Refer to Removal and Installation.

CHECK TERMINAL

  1. Check parking brake switch terminals for damage or loose connection with harness connector.

  2. Check ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair/replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Connect the parking brake switch harness connector.

  2. Connect the ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12 V battery negative terminal.

  4. Ignition switch ON.

  5. Apply and release the parking brake five times.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C10B2-01” detected?

YES>>

"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

Inspection End

Component Inspection

CHECK PARKING BRAKE SWITCH

  1. Disconnect 12V battery negative terminal.

  2. Disconnect the parking brake switch harness connector.

  3. Check the continuity when parking brake switch is operated.

    ConditionTerminalsContinuity
    When parking brake switch is neutral 3 5 Yes
    6 7 Yes
    3 6 No
    5 7 No
    When parking brake switch is pull 3 5 Yes
    5 7 Yes
    3 6 No
    6 7 No
    When parking brake switch is push 3 6 Yes
    6 7 Yes
    3 5 No
    5 7 No

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the parking brake switch. Refer to Removal and Installation.

CHECK PARKING BRAKE SWITCH INDICATOR

Apply 12 V between parking brake switch connector terminals, and check the parking brake switch indicator lamp.

Parking brake switchConditionParking brake switch indicator
Terminal
(+)(–)
2 9 Apply 12 V between parking brake switch connector terminals (2 and 9). ON

Is the inspection result normal?

YES>>

Inspection End

NO>>

Replace the parking brake switch. Refer to Removal and Installation.

C10b3 Parking Brake Control Module Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C10B3–44

Parking brake control module

(Parking brake control module)
Diagnosis condition When power switch is ON
Signal (terminal) —
Threshold When an internal malfunctioning in the ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less
C10B3–49

Parking brake control module

(Parking brake control module)
Diagnosis condition When power switch is ON
Signal (terminal) —
Threshold When an internal malfunctioning in the ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less
C10B3–53

Parking brake control module

(Parking brake control module)
Diagnosis condition When power switch is ON
Signal (terminal) —
Threshold When an internal malfunctioning in the ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less
C10B3–55

Parking brake control module

(Parking brake control module)
Diagnosis condition When power switch is ON
Signal (terminal) —
Threshold When an internal malfunctioning in the ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less
C10B3–68

Parking brake control module

(Parking brake control module)
Diagnosis condition When power switch is ON
Signal (terminal) —
Threshold When an internal malfunctioning in the ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less
C10B3–98

Parking brake control module

(Parking brake control module)
Diagnosis condition When power switch is ON
Signal (terminal) —
Threshold When an internal malfunctioning in the ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • Parking brake actuator

  • Rear brake caliper assembly

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • Parking brake actuator

  • Rear brake caliper assembly

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended:

Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON.

  2. Push the parking brake switch.

  3. Pull the parking brake switch.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C10B3” detected?

YES>>

“CRNT” is displayed: Refer to DTC Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Ignition switch ON.

  3. Operate parking brake switch (apply/release) five times.

  4. Ignition switch OFF (Auto ACC function OFF).

  5. Ignition switch ON.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C10B3-44” detected?

YES>>

"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

Inspection End