Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm))

In this manual: Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm))
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
89steps
~534min
4/5difficulty
Done 0 of 89
  • B24a6-15 in-Vehicle Sensor
  • B24b4-02 A/c Control Comm
  • B24c6-12 Blower Motor Control
  • B24f5-93 Mode Door Motor
  • U1ca1-08 A/c Switch Assembly Communication
  • U1ca2-08 Door Motor Communication
  • U1caa-02 Mode Door Motor
  • U2140-87 Can Comm Err (ecm)

B24a6-15 in-Vehicle Sensor Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B24A6-15

IN-Nissan Pathfinder Vehicle SENSOR

(In-vehicle sensor)
Diagnosis condition Ignition switch ON
Signal (Terminal) In-Nissan Pathfinder vehicle sensor signal
Threshold The in-Nissan Pathfinder vehicle sensor recognition temperature is too low [less than -44°F (-42°C)]
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Front in-vehicle sensor

  • A/C auto amp.

  • Harness or connectors (the sensor circuit is open or shorted to battery)

FAIL-SAFE

In-vehicle temperature is calculated as 77°F (25°C) and air conditioning system is controlled.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK FRONT IN-VEHICLE SENSOR SIGNAL

  1. Ignition switch ON.

  2. Check voltage between A/C auto amp. harness connector.

    A/C auto amp.

    Voltage

    (Approx.)
    ConnectorTerminals
    +-
    M60 48 78

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK FRONT IN-Nissan Pathfinder Vehicle SENSOR POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect front in-vehicle sensor connector.

  3. Ignition switch ON.

  4. Check voltage between front in-Nissan Pathfinder vehicle sensor harness connector and ground.

    +-

    Voltage

    (Approx.)
    Front in-Nissan Pathfinder vehicle sensor
    ConnectorTerminal
    M102 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 5.

CHECK FRONT IN-Nissan Pathfinder Vehicle SENSOR GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect A/C auto amp. connector.

  3. Check continuity between front in-Nissan Pathfinder vehicle sensor harness connector and A/C auto amp. harness connector.

    Front in-Nissan Pathfinder vehicle sensorA/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M102 2 M60 78 Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair harness or connector.

CHECK FRONT IN-Nissan Pathfinder Vehicle SENSOR

Check front in-vehicle sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

Replace front in-Nissan Pathfinder vehicle sensor. Refer to Removal and Installation.

CHECK FRONT IN-Nissan Pathfinder Vehicle SENSOR POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect A/C auto amp. connector.

  3. Check continuity between front in-Nissan Pathfinder vehicle sensor harness connector and A/C auto amp. harness connector.

    Front in-Nissan Pathfinder vehicle sensorA/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M102 1 M60 48 Yes

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair harness or connector.

CHECK FRONT IN-Nissan Pathfinder Vehicle SENSOR POWER SUPPLY CIRCUIT FOR SHORT

Check voltage between front in-vehicle sensor harness connector and ground.

+-

Voltage

(Approx.)
Front in-Nissan Pathfinder vehicle sensor
ConnectorTerminal
M102 1 Ground 0 V

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

Component Inspection

CHECK FRONT IN-VEHICLE SENSOR

  1. Ignition switch OFF.

  2. Remove front in-Nissan Pathfinder vehicle sensor. Refer to Removal and Installation.

  3. Check resistance between front in-vehicle sensor terminals. Refer to applicable table for the normal value.

    Front in-Nissan Pathfinder vehicle sensorConditionResistance: kΩ
    TerminalsTemperature: °F (°C)
    1 2 −4 (−20) 16.50
    14 (−10) 9.92
    32 (0) 6.19
    50 (10) 3.99
    68 (20) 2.65
    77 (25) 2.19
    86 (30) 1.81
    104 (40) 1.27

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace front in-Nissan Pathfinder vehicle sensor. Refer to Removal and Installation.

B24b4-02 A/c Control Comm Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B24B4-02

A/C CONTROL COMM

(Air conditioning control communication)
Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (A/C switch assembly) signal
Threshold Receive internal circuit error message via front A/C switch assembly to LIN communication
Diagnosis delay time 30 second or more

POSSIBLE CAUSE

Front A/C switch assembly (internal circuit malfunction)

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Select “ERASE”.

  4. Ignition switch OFF.

  5. Ignition switch ON.

  6. Perform “DTC CONFIRMATION PROCEDURE”. Refer to DTC Description.

Is DTC detected again?

YES>>

Replace front A/C switch assembly. Refer to Removal and Installation.

NO>>

Inspection End.

B24c6-12 Blower Motor Control Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B24C6-12

BLOWER MOTOR CONTROL

(Blower motor control)
[CIRCUIT SHORT TO GROUND] Diagnosis condition When ignition switch is ON
Signal (Terminal) Blower motor control signal
Threshold Blower motor control signal circuit has a short to ground
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (blower motor control signal circuit is shorted to ground)

  • A/C auto amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK FRONT BLOWER MOTOR CONTROL SIGNAL

  1. Ignition switch ON.

  2. Check duty ratios between front blower motor harness connector and ground by using an oscilloscope.

    (+)(–)Condition

    Output waveform

    (Approx.)
    Front blower motor
    ConnectorTerminal
    M187 2 Ground Front blower motor: OFF Battery voltage
    Front blower motor: 1st speed (manual)
    Front blower motor: 7th speed (manual)

Is the inspection result normal?

YES>>

Replace front blower motor. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK FRONT BLOWER MOTOR CONTROL SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect front blower motor connector and A/C auto amp. connector.

  3. Check continuity between front blower motor harness connector and A/C auto amp. harness connector.

    Front blower motorA/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M187 2 M50 34 Yes
  4. Check continuity between front blower motor harness connector and ground.

    Front blower motor(–)Continuity
    ConnectorTerminal
    M187 2 Ground No

Is the inspection result normal?

YES>>

Replace the A/C auto amp. Refer to Removal and Installation.

NO>>

Repair the harnesses or connectors.

B24f5-93 Mode Door Motor Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B24F5-93

Mode door motor

(Mode door motor)
Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (door motor) signal
Threshold Drive error of mode door motor (front) is detected
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Harness and connector [mode door motor (front) circuit is open or shorted to ground]

  • Mode door motor (front) installation condition

  • Mode door motor (front)

  • A/C auto amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Start the engine.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK MODE DOOR MOTOR (FRONT) POWER SUPPLY

  1. Ignition switch ON.

  2. Check voltage between mode door motor (front) harness connector and ground.

+−

Voltage

(Approx.)
Mode door motor (front)
ConnectorTerminal
M129 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK MODE DOOR MOTOR (FRONT) GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect mode door motor (front) connector and A/C auto amp. connector.

  3. Check continuity between mode door motor (front) harness connector and A/C auto amp. harness connector.

    Mode door motor (front)A/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M129 2 M50 27 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK MODE DOOR MOTOR (FRONT) LIN SIGNAL CIRCUIT

  1. Connect mode door motor (front) connector and A/C auto amp. connector.

  2. Ignition switch ON.

  3. Confirm output waveform between mode door motor (front) harness connector and ground with oscilloscope.

    +−Output waveform
    Mode door motor
    ConnectorTerminal
    M129 3 Ground

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 6.

CHECK INSTALLATION OF MODE DOOR MOTOR (FRONT)

Check mode door motor (front) is properly installed. Refer to Exploded View.

Is the inspection result normal?

YES>>

Replace mode door motor (front). Refer to Removal and Installation - Mode Door Motor (Front).

NO>>

Repair or replace malfunctioning part.

CHECK MODE DOOR MOTOR (FRONT) POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect mode door motor (front) connector and A/C auto amp. connector.

  3. Check continuity between mode door motor (front) harness connector and A/C auto amp. harness connector.

    Mode door motor (front)A/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M129 1 M50 1 Yes

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

CHECK MODE DOOR MOTOR (FRONT) LIN SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect mode door motor (front) connector and A/C auto amp. connector.

  3. Check continuity between mode door motor (front) harness connector and A/C auto amp. harness connector.

    Mode door motor (front)A/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M129 3 M50 2 Yes

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

U1ca1-08 A/c Switch Assembly Communication Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1CA1-08

LIN communication 2

(Local interconnect network communication 2)
Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (A/C control) signal
Threshold A/C auto amp. is not transmitting or receiving LIN communication with front A/C switch assembly or rear A/C switch assembly
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Front A/C switch assembly

  • Rear A/C switch assembly

  • A/C auto amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK DTC

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check following DTC:

    DTC

    Items

    (CONSULT screen terms)
    Reference
    B24B4-02 A/C CONTROL COMM DTC Description
    U1CB1-02 A/C control 2 communication DTC Description

Is DTC detected?

YES>>

Perform DTC diagnosis procedure that is detecting.

NO>>

Replace A/C auto amp. Refer to Removal and Installation.

U1ca2-08 Door Motor Communication Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1CA2-08

LIN communication 3

(Local interconnect network communication 3)
Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (door motor) signal
Threshold A/C auto amp. is not transmitting or receiving LIN communication with each door motor
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Harness and connector (door motor circuit is open or shorted to ground)

  • Each door motor

  • A/C auto amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Start the engine.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK DTC

CONSULT

  1. Start the engine.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check following DTC:

    DTC

    Items

    (CONSULT screen terms)
    Reference
    U1CAA-02 Mode door motor DTC Description
    U1CAB-02 Intake door motor DTC Description
    U1CAC-02 Air mix door motor 1 DTC Description
    U1CAD-02 Air mix door motor 2 DTC Description
    U1CAE-02 Rear air mix door motor DTC Description

Is DTC detected?

YES>>

Perform DTC diagnosis procedure that is detecting.

NO>>

Replace A/C auto amp. Refer to Removal and Installation.

U1caa-02 Mode Door Motor Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1CAA-02

Mode door motor

(Mode door motor)
Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (door motor) signal
Threshold A/C auto amp. is not transmitting or receiving LIN communication with mode door motor (front)
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Harness and connector [mode door motor (front) circuit is open or shorted to ground]

  • Mode door motor (front)

  • A/C auto amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Start the engine.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK MODE DOOR MOTOR (FRONT) POWER SUPPLY

  1. Ignition switch ON.

  2. Check voltage between mode door motor (front) harness connector and ground.

+−

Voltage

(Approx.)
Mode door motor (front)
ConnectorTerminal
M129 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK MODE DOOR MOTOR (FRONT) GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect mode door motor (front) connector and A/C auto amp. connector.

  3. Check continuity between mode door motor (front) harness connector and A/C auto amp. harness connector.

    Mode door motor (front)A/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M129 2 M50 27 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK MODE DOOR MOTOR (FRONT) LIN SIGNAL CIRCUIT

  1. Connect mode door motor (front) connector and A/C auto amp. connector.

  2. Ignition switch ON.

  3. Confirm output waveform between mode door motor (front) harness connector and ground with oscilloscope.

    +−Output waveform
    Mode door motor (front)
    ConnectorTerminal
    M129 3 Ground

Is the inspection result normal?

YES>>

Replace mode door motor (front). Refer to Removal and Installation - Mode Door Motor (Front).

NO>>

GO TO 6.

CHECK MODE DOOR MOTOR (FRONT) POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect mode door motor (front) connector and A/C auto amp. connector.

  3. Check continuity between mode door motor (front) harness connector and A/C auto amp. harness connector.

    Mode door motor (front)A/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M129 1 M50 1 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair harness or connector.

CHECK MODE DOOR MOTOR (FRONT) POWER SUPPLY CIRCUIT FOR SHORT

  1. Disconnect following connectors:

    • Air mix door motor LH

    • Air mix door motor RH

    • Air mix door motor (rear)

    • Intake door motor

    • Mode door motor (rear)

  2. Check continuity between mode door motor harness connector and ground.

    Mode door motor (front)—Continuity
    ConnectorTerminal
    M129 1 Ground No

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

CHECK MODE DOOR MOTOR (FRONT) LIN SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect mode door motor (front) connector and A/C auto amp. connector.

  3. Check continuity between mode door motor (front) harness connector and A/C auto amp. harness connector.

    Mode door motor (front)A/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    M129 3 M50 2 Yes

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair harness or connector.

CHECK MODE DOOR MOTOR (FRONT) LIN SIGNAL CIRCUIT FOR SHORT

  1. Disconnect following connectors:

    • Air mix door motor LH

    • Air mix door motor RH

    • Air mix door motor (rear)

    • Intake door motor

    • Mode door motor (rear)

  2. Check continuity between mode door motor (front) harness connector and ground.

    Mode door motor (front)—Continuity
    ConnectorTerminal
    M129 3 Ground No

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

U2140-87 Can Comm Err (ecm) Nissan Pathfinder 2022

DTC Description

DESCRIPTION

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Pathfinder vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
U2140–87

CAN comm err (ECM)

[CAN communication error (ECM)]
Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold A/C auto amp. is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK CAN COMMUNICATION SYSTEM

Check CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

Inspection End.