Lan System - Dtc/circuit Diagnosis

In this manual: Lan System - Dtc/circuit Diagnosis
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
201steps
~1206min
5/5difficulty
Done 0 of 201
  • Malfunction Area Chart
  • Main Line Between Hvac and a-Bag Circuit
  • Main Line Between M&a and Pwbd Circuit
  • Main Line Between Sonar and Avm Circuit
  • Main Line Between Tcm and E-Shift Circuit
  • Main Line Between Wl Chg and Av Circuit
  • Main Line Between Av and a-Amp. Circuit
  • Hfm Branch Line Circuit
  • A-Bag Branch Line Circuit
  • M&a Branch Line Circuit
  • Adp Branch Line Circuit
  • Avm Branch Line Circuit (its Can Communication 1 Circuit)
  • Lane Branch Line Circuit
  • E-Hud Branch Line Circuit
  • Strg Branch Line Circuit
  • Abs Branch Line Circuit
  • E-Shift Branch Line Circuit
  • Av Branch Line Circuit
  • Wl Chg Branch Line Circuit
  • Dlc Branch Line Circuit
  • Vehicle Can Communication 2 Circuit
  • Vehicle Can Communication 3 Circuit
  • Its Can Communication 3 Circuit
  • Its Can Communication 4 Circuit
  • Its Can Communication 5 Circuit
  • Chassis Can Communication 2 Circuit
  • Drivetrain Can Communication 1 Circuit
  • Diagnostic Can Communication Circuit

Malfunction Area Chart Nissan Pathfinder

Vehicle CAN Communication Circuit

MAIN LINE

Malfunction areaReference
Main line between A/C auto amp. and air bag diagnosis sensor unit circuit Diagnosis Procedure
Main line between combination meter and automatic back door control unit circuit Diagnosis Procedure

BRANCH LINE

Malfunction areaReference
Intelligent key unit branch line circuit Diagnosis Procedure
A/C auto amp. branch line circuit Diagnosis Procedure
Air bag diagnosis sensor unit branch line circuit Diagnosis Procedure
IPDM E/R branch line circuit Diagnosis Procedure
Combination meter branch line circuit Diagnosis Procedure
Automatic drive positioner control unit branch line circuit Diagnosis Procedure
Automatic back door control unit branch line circuit Diagnosis Procedure
Driver seat control unit branch line circuit Diagnosis Procedure

SHORT CIRCUIT OR OPEN CIRCUIT

Malfunction areaReference
Nissan Pathfinder Vehicle CAN communication 1 circuit Diagnosis Procedure
Vehicle CAN communication 2 circuit Diagnosis Procedure
Nissan Pathfinder Vehicle CAN communication 3 circuit Diagnosis Procedure

ITS CAN Communication Circuit

MAIN LINE

Malfunction areaReference
Main line between sonar control unit and around view monitor control unit circuit Diagnosis Procedure

BRANCH LINE

Malfunction areaReference
Around view monitor control unit branch line circuit (ITS CAN communication 1 circuit) Diagnosis Procedure
ADAS control unit 2 branch line circuit (ITS CAN communication 1 circuit) Diagnosis Procedure
Front camera unit branch line circuit Diagnosis Procedure
Distance sensor branch line circuit Diagnosis Procedure
Side radar LH branch line circuit Diagnosis Procedure
Side radar RH branch line circuit Diagnosis Procedure
Around view monitor control unit branch line circuit (ITS CAN communication 4 circuit) Diagnosis Procedure
Sonar control unit branch line circuit Diagnosis Procedure
ADAS control unit 2 branch line circuit (ITS CAN communication 4 circuit) Diagnosis Procedure

SHORT CIRCUIT OR OPEN CIRCUIT

Malfunction areaReference
ITS CAN communication 1 circuit Diagnosis Procedure
ITS CAN communication 2 circuit Diagnosis Procedure
ITS CAN communication 3 circuit Diagnosis Procedure
ITS CAN communication 4 circuit Diagnosis Procedure
ITS CAN communication 5 circuit Diagnosis Procedure

Chassis Communication Circuit

BRANCH LINE

Malfunction areaReference
4WD control unit branch line circuit Diagnosis Procedure
EPS control unit branch line circuit Diagnosis Procedure
Head up display unit branch line circuit Diagnosis Procedure
Steering angle sensor branch line circuit Diagnosis Procedure
ABS actuator and electric unit (control unit) branch line circuit Diagnosis Procedure

SHORT CIRCUIT

Malfunction areaReference
Chassis CAN communication 1 circuit Diagnosis Procedure
Chassis CAN communication 2 circuit Diagnosis Procedure
Chassis CAN communication 3 circuit Diagnosis Procedure
Chassis CAN communication 4 circuit Diagnosis Procedure

Drivetrain CAN Communication Circuit

MAIN LINE

Malfunction areaReference
Main line between TCM and electric shift control module circuit Diagnosis Procedure

BRANCH LINE

Malfunction areaReference
TCM branch line circuit (Drivetrain CAN communication 1 circuit) Diagnosis Procedure
Electric shift control module branch line circuit Diagnosis Procedure
Chassis control module branch line circuit Diagnosis Procedure
TCM branch line circuit (Drivetrain CAN communication 2 circuit) Diagnosis Procedure
ECM branch line circuit Diagnosis Procedure

SHORT CIRCUIT OR OPEN CIRCUIT

Malfunction areaReference
Drivetrain CAN communication 1 circuit Diagnosis Procedure
Drivetrain CAN communication 2 circuit Diagnosis Procedure

IT CAN Communication Circuit

MAIN LINE

Malfunction areaReference
Main line between wireless charger unit and AV control unit circuit Diagnosis Procedure
Main line between AV control unit and BOSE speaker amp. circuit Diagnosis Procedure

BRANCH LINE

Malfunction areaReference
AV control unit branch line circuit Diagnosis Procedure
TCU branch line circuit Diagnosis Procedure
Wireless charger unit branch line circuit Diagnosis Procedure
BOSE speaker amp. branch line circuit Diagnosis Procedure

SHORT CIRCUIT OR OPEN CIRCUIT

Malfunction areaReference
IT CAN communication circuit Diagnosis Procedure

Engine CAN Communication Circuit

SHORT CIRCUIT OR OPEN CIRCUIT

Malfunction areaReference
Engine CAN communication circuit Diagnosis Procedure

Diagnostic CAN Communication Circuit

BRANCH LINE

Malfunction areaReference
Data link connector branch line circuit Diagnosis Procedure

SHORT CIRCUIT OR OPEN CIRCUIT

Malfunction areaReference
Diagnostic CAN communication circuit Diagnosis Procedure

Main Line Between Hvac and a-Bag Circuit Nissan Pathfinder 2022

Diagnosis Procedure

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect the following harness connectors.

    • A/C auto amp.

    • Harness connectors M31 and E152

  4. Check the continuity between the A/C auto amp. harness connector and the harness connector.

    A/C auto amp. harness connector Harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    M60 50 M31 47G Existed
    70 46G Existed

Is the inspection result normal?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the main line between the A/C auto amp. and the air bag diagnosis sensor unit.

NO>>

Repair the main line between the A/C auto amp. and the air bag diagnosis sensor unit harness connector.

Main Line Between M&a and Pwbd Circuit Nissan Pathfinder 2026

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).

    • Harness connector M40

    • Harness connector B69

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the following harness connectors.

    • Combination meter

    • Harness connectors M40 and B69

  2. Check the continuity between the combination meter harness connector and the harness connector.

    • With full TFT meter

      Combination meter harness connector Harness connector Continuity
      Connector No. Terminal No. Connector No. Terminal No.
      M44 18 M40 50A Existed
      19 49A Existed
    • With 7 inch information display meter

      Combination meter harness connector Harness connector Continuity
      Connector No. Terminal No. Connector No. Terminal No.
      M24 18 M40 50A Existed
      19 49A Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the main line between the combination meter and the harness connector M40.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of automatic back door control unit.

  2. Check the continuity between the harness connector and the automatic back door control unit harness connector.

Harness connector Automatic back door control unit harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
B69 50A B55 32 Existed
49A 16 Existed

Is the inspection result normal?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the main line between the combination meter and the automatic back door control unit.

NO>>

Repair the main line between the harness connector B69 and the automatic back door control unit.

Main Line Between Sonar and Avm Circuit Nissan Pathfinder Fifth generation

Diagnosis Procedure

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect the following harness connectors.

    • Sonar control unit

    • Around view monitor control unit

    • 8CH CAN gateway

  4. Check the continuity between the sonar control unit harness connector and the around view monitor control unit harness connector.

    Sonar control unit harness connector Around view monitor control unit harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    M70 5 M96 6 Existed
    6 23 Existed

Is the inspection result normal?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the main line between the sonar control unit and the around view monitor control unit.

NO>>

Repair the main line between the sonar control unit and the around view monitor control unit.

Main Line Between Tcm and E-Shift Circuit Nissan Pathfinder

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).

    • Harness connector F32

    • Harness connector E2

    • Harness connector E152

    • Harness connector M31

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the following harness connectors.

    • TCM

    • Harness connectors F32 and E2

  2. Check the continuity between the TCM harness connector and the harness connector.

    TCM harness connector Harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    F15 34 F32 20 Existed
    47 21 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the main line between the TCM and the harness connector F32.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the following harness connectors E152 and M31.

  2. Check the continuity between the harness connector terminals.

    Harness connector Harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    E2 20 E152 23G Existed
    21 22G Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the main line between the harness connector E2 and E152.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the harness connector terminals.

Harness connector Continuity
Connector No. Terminal No. Terminal No.
M31 23G 84G Existed
22G 83G Existed

Is the inspection result normal?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the main line between the TCM and the electric shift control module.

NO>>

Repair the main line between the harness connector M31 terminals.

Main Line Between Wl Chg and Av Circuit Nissan Pathfinder Fifth generation

Diagnosis Procedure

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect the following harness connectors.

    • Wireless charger unit

    • AV control unit

    • 8CH CAN gateway

  4. Check the continuity between the wireless charger unit harness connector and the AV control unit harness connector.

    Wireless charger unit harness connector AV control unit harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    M63 1 M160 21 Existed
    2 41 Existed

Is the inspection result normal?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the main line between the wireless charger unit and the AV control unit.

NO>>

Repair the main line between the wireless charger unit and the AV control unit.

Main Line Between Av and a-Amp. Circuit Nissan Pathfinder R53

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).

    • Harness connector M84

    • Harness connector B101

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the following harness connectors.

    • AV control unit

    • Harness connectors M84 and B101

  2. Check the continuity between the AV control unit harness connector and the harness connector.

    AV control unit harness connector Harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    M160 21 M84 50M Existed
    41 49M Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the main line between the AV control unit and the harness connector M84.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of BOSE speaker amp..

  2. Check the continuity between the harness connector and the BOSE speaker amp. harness connector.

    Harness connector BOSE speaker amp. harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    B101 50M B129 10 Existed
    49M 11 Existed

Is the inspection result normal?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the main line between the AV control unit and the BOSE speaker amp.

NO>>

Repair the main line between the harness connector B101 and the BOSE speaker amp.

Hfm Branch Line Circuit Nissan Pathfinder

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the terminals and connectors of the Intelligent Key unit for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of Intelligent Key unit.

  2. Check the resistance between the Intelligent Key unit harness connector terminals.

    Intelligent Key unit harness connector Resistance (Ω)
    Connector No. Terminal No.
    M38 6 7 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 3.

NO>>

Repair the Intelligent Key unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the Intelligent Key unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the Intelligent Key unit. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the Intelligent Key unit branch line.

NO>>

Repair the power supply and the ground circuit.

A-Bag Branch Line Circuit Nissan Pathfinder Fifth generation

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the terminals and connectors of the air bag diagnosis sensor unit for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the main harness.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Check the air bag diagnosis sensor unit. Refer to Work Flow.

Is the inspection result normal?

YES>>

Replace the main harness.

NO>>

Replace parts whose air bag system has a malfunction.

M&a Branch Line Circuit Nissan Pathfinder 2022

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Combination meter

    • BCM

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of BCM.

  2. Check the continuity between the BCM harness connector terminals.

BCM harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
M80 118 B59 87 Existed
117 86 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair the root cause (Nissan Pathfinder vehicle CAN communication 2 circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Connect the connector of BCM.

  2. Disconnect the connector of combination meter.

  3. Check the resistance between the combination meter harness connector terminals.

    • With full TFT meter

      Combination meter harness connector Resistance (Ω)
      Connector No. Terminal No.
      M44 18 19 Approx. 54 – 66
    • With 7 inch information display meter

      Combination meter harness connector Resistance (Ω)
      Connector No. Terminal No.
      M24 18 19 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 4.

NO>>

Repair the combination meter branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the combination meter. Refer to the following.

  • Full TFT meter: Diagnosis Procedure

  • 7 inch information display: Diagnosis Procedure

Is the inspection result normal?

YES (Present error)>>

Replace the combination meter. Refer to the following.

  • Full TFT meter: Removal and Installation

  • 7 inch information display: Removal and Installation

YES (Past error)>>

Error was detected in the combination meter branch line.

NO>>

Repair the power supply and the ground circuit.

Adp Branch Line Circuit Nissan Pathfinder R53

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Driver seat control unit

    • Harness connector B220

    • Harness connector B74

    • BCM

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of BCM.

  2. Check the continuity between the BCM harness connector terminals.

BCM harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
M80 118 B59 87 Existed
117 86 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair the root cause (Nissan Pathfinder vehicle CAN communication 2 circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of driver seat control unit.

  2. Check the resistance between the driver seat control unit harness connector terminals.

    Driver seat control unit harness connector Resistance (Ω)
    Connector No. Terminal No.
    B209 20 19 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 4.

NO>>

Repair the driver seat control unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the driver seat control unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the driver seat control unit. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the driver seat control unit branch line.

NO>>

Repair the power supply and the ground circuit.

Avm Branch Line Circuit (its Can Communication 1 Circuit) Nissan Pathfinder

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Around view monitor control unit

    • 8CH CAN gateway

Is the inspection result normal?

YES-1>>

Without Automatic Emergency Braking: GO TO 2.

YES-2>>

With Automatic Emergency Braking: GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M159 44 35 Existed
    43 36 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair the root cause (ITS CAN communication 1 circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of 8CH CAN gateway. (Without Automatic Emergency Braking)

  2. Disconnect the connector of around view monitor control unit.

  3. Check the resistance between the around view monitor control unit harness connector terminals.

    Around view monitor control unit harness connector Resistance (Ω)
    Connector No. Terminal No.
    M96 3 20 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 4.

NO>>

Repair the around view monitor control unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the around view monitor control unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the around view monitor control unit. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the around view monitor control unit branch line.

NO>>

Repair the power supply and the ground circuit.

Lane Branch Line Circuit Nissan Pathfinder 2026

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Front camera unit

    • Harness connector R1

    • Harness connector M1

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of front camera unit.

  2. Check the resistance between the front camera unit harness connector terminals.

    Front camera unit harness connector Resistance (Ω)
    Connector No. Terminal No.
    R17 7 3 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 3.

NO>>

Repair the front camera unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the front camera unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the front camera unit. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the front camera unit branch line.

NO>>

Repair the power supply and the ground circuit.

E-Hud Branch Line Circuit Nissan Pathfinder SUV

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the terminals and connectors of the head up display unit for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of head up display unit.

  2. Check the resistance between the head up display unit harness connector terminals.

    Head up display unit harness connector Resistance (Ω)
    Connector No. Terminal No.
    M107 3 5 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 3.

NO>>

Repair the head up display unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the head up display unit. Refer to the following.

  • Full TFT meter: Diagnosis Procedure

  • 7 inch information display: Diagnosis Procedure

Is the inspection result normal?

YES (Present error)>>

Replace the head up display unit. Refer to the following.

  • Full TFT meter: Removal and Installation

  • 7 inch information display: Removal and Installation

YES (Past error)>>

Error was detected in the head up display unit branch line.

NO>>

Repair the power supply and the ground circuit.

Strg Branch Line Circuit Nissan Pathfinder R53

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the terminals and connectors of the steering angle sensor for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of steering angle sensor.

  2. Check the resistance between the steering angle sensor harness connector terminals.

    Steering angle sensor harness connector Resistance (Ω)
    Connector No. Terminal No.
    M54 6 7 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 3.

NO>>

Repair the steering angle sensor branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the steering angle sensor. Refer to Wiring Diagram.

Is the inspection result normal?

YES (Present error)>>

Replace the steering angle sensor. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the steering angle sensor branch line.

NO>>

Repair the power supply and the ground circuit.

Abs Branch Line Circuit Nissan Pathfinder

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the terminals and connectors of the ABS actuator and electric unit (control unit) for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of ABS actuator and electric unit (control unit).

  2. Check the resistance between the ABS actuator and electric unit (control unit) harness connector terminals.

    ABS actuator and electric unit (control unit) harness connector Resistance (Ω)
    Connector No. Terminal No.
    E125 5 19 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 3.

NO>>

Repair the ABS actuator and electric unit (control unit) branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the ABS actuator and electric unit (control unit). Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the ABS actuator and electric unit (control unit) branch line.

NO>>

Repair the power supply and the ground circuit.

E-Shift Branch Line Circuit Nissan Pathfinder SUV

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the terminals and connectors of the electric shift control module for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of electric shift control module.

  2. Check the resistance between the electric shift control module harness connector terminals.

    Electric shift control module harness connector Resistance (Ω)
    Connector No. Terminal No.
    M36 32 16 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 3.

NO>>

Repair the electric shift control module branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the electric shift control module. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the electric shift control module. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the electric shift control module branch line.

NO>>

Repair the power supply and the ground circuit.

Av Branch Line Circuit Nissan Pathfinder

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • AV control unit

    • 8CH CAN gateway

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M5 22 19 Existed
    23 20 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair the root cause (diagnosis CAN communication circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Connect the connector of 8CH CAN gateway.

  2. Disconnect the connector of AV control unit.

  3. Check the resistance between the AV control unit harness connector terminals.

    • Without BOSE audio system

      AV control unit harness connector Resistance (Ω)
      Connector No. Terminal No.
      M123 21 41 Approx. 54 – 66
    • With BOSE audio system

      AV control unit harness connector Resistance (Ω)
      Connector No. Terminal No.
      M160 21 41 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 4.

NO>>

Repair the AV control unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the AV control unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the AV control unit. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the AV control unit branch line.

NO>>

Repair the power supply and the ground circuit.

Wl Chg Branch Line Circuit Nissan Pathfinder 2022

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Wireless charger unit

    • Harness connector M215

    • Harness connector M63

    • 8CH CAN gateway

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M5 22 19 Existed
    23 20 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair the root cause (IT CAN communication circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Connect the connector of 8CH CAN gateway.

  2. Disconnect the connector of wireless charger unit.

  3. Check the resistance between the wireless charger unit harness connector terminals.

    Wireless charger unit harness connector Resistance (Ω)
    Connector No. Terminal No.
    M216 2 6 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 4.

NO>>

Repair the wireless charger unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the wireless charger unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the wireless charger unit. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the wireless charger unit branch line.

NO>>

Repair the power supply and the ground circuit.

Dlc Branch Line Circuit Nissan Pathfinder

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).

    • Data link connector

    • 8CH CAN gateway

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M5 5 3 Existed
    4 2 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair the root cause (diagnosis CAN communication circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Connect the connector of 8CH CAN gateway.

  2. Check the resistance between the data link connector terminals.

    Data link connector Resistance (Ω)
    Connector No. Terminal No.
    M22 6 14 Approx. 54 – 66

Is the measurement value within the specification?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the data link connector branch line circuit.

NO>>

Repair the data link connector branch line.

Vehicle Can Communication 2 Circuit Nissan Pathfinder 2026

Diagnosis Procedure

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the unit connectors on Nissan Pathfinder vehicle CAN communication 2 circuit.

  4. Check the terminals and connectors for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the BCM harness connector terminals.

BCM harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
B59 87 M80 118 Existed
86 117 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the BCM harness connector terminals.

BCM harness connector Continuity
Connector No. Terminal No.
B59 87 86 Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the BCM and the ground.

BCM harness connector Ground Continuity
Connector No. Terminal No.
B59 87 Not existed
86 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace the root cause.

CHECK BCM TERMINATION CIRCUIT

  1. Remove the BCM.

  2. Check the resistance between the BCM terminals.

    BCM Resistance (Ω)
    Terminal No.
    87 86 Approx. 108 – 132
    118 117 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 6.

NO>>

Replace the BCM.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 7.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of Nissan Pathfinder vehicle CAN communication circuit 2.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

Vehicle Can Communication 3 Circuit Nissan Pathfinder 2026

Diagnosis Procedure

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the control unit connectors on Nissan Pathfinder vehicle CAN communication 3 circuit.

  4. Check the terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector and BCM harness connector.

8CH CAN gateway harness connector BCM harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
M159 33 M19 45 Existed
34 46 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector terminals.

8CH CAN gateway harness connector Continuity
Connector No. Terminal No.
M159 33 34 Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway and the ground.

8CH CAN gateway harness connector Ground Continuity
Connector No. Terminal No.
M159 33 Not existed
34 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace (if shield line is short) the root cause.

CHECK 8CH CAN gateway AND BCM TERMINATION CIRCUIT

  1. Remove the 8CH CAN gateway and the BCM.

  2. Check the resistance between the 8CH CAN gateway terminals.

    8CH CAN gateway Resistance (Ω)
    Terminal No.
    33 34 Approx. 108 – 132
  3. Check the resistance between the BCM terminals.

    BCM Resistance (Ω)
    Terminal No.
    45 46 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 6.

NO (BCM)>>

Replace the BCM.

NO (8CH CAN gateway)>>

GO TO 8.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 7.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of Nissan Pathfinder vehicle CAN communication 3 circuit.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

CHECK WARNING LAMP

  1. Turn the ignition switch ON.

  2. Check the following warning lamp.

    • VDC warning lamp

    • Brake warning lamp

    • Engine oil pressure warning lamp

Is any of the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 9.

CHECK NAVIGATION SYSTEM OPERATION

Check navigation system operation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the 8CH CAN gateway.

Its Can Communication 3 Circuit Nissan Pathfinder

Diagnosis Procedure

CHECK CAN DIAGNOSIS

Check the CAN diagnosis results from CONSULT to see that the ITS CAN communication 1 circuit and ITS CAN communication 4 circuit have no malfunction.

Are the ITS CAN communication 1 circuit and ITS CAN communication 4 circuit normal?

YES>>

GO TO 2.

NO>>

Check and repair ITS CAN communication 1 circuit and/or ITS CAN communication 4 circuit.

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the control unit connectors on ITS CAN communication 3 circuit.

  4. Check the terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the ADAS control unit 2 harness connector and harness connector M74.

ADAS control unit 2 harness connector Harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
M192 31 M74 1 Existed
32 2 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the ADAS control unit 2 harness connector terminals.

ADAS control unit 2 harness connector Continuity
Connector No. Terminal No.
M192 31 32 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the ADAS control unit 2 and the ground.

ADAS control unit 2 harness connector Ground Continuity
Connector No. Terminal No.
M192 31 Not existed
32 Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Check the harness and repair or replace (if shield line is short) the root cause.

CHECK SIDE RADAR LH AND SIDE RADAR RH TERMINATION CIRCUIT

  1. Remove the side radar LH and the side radar RH.

  2. Check the resistance between the side radar LH terminals.

    Side radar LH Resistance (Ω)
    Terminal No.
    1 2 Approx. 108 – 132
  3. Check the resistance between the side radar RH terminals.

    Side radar RH Resistance (Ω)
    Terminal No.
    1 2 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 7.

NO>>

Replace the side radar LH and/or the side radar RH.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 8.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of ITS CAN communication 3 circuit.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

Its Can Communication 4 Circuit Nissan Pathfinder

Diagnosis Procedure

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the control unit connectors on ITS CAN communication 4 circuit.

  4. Check the terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES-1>>

With Automatic Emergency Braking: GO TO 2.

YES-2>>

Without Automatic Emergency Braking: GO TO 6.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector and ADAS control unit 2 harness connector.

8CH CAN gateway harness connector ADAS control unit 2 harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
M159 37 M192 28 Existed
38 29 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector terminals.

8CH CAN gateway harness connector Continuity
Connector No. Terminal No.
M159 37 38 Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway and the ground.

8CH CAN gateway harness connector Ground Continuity
Connector No. Terminal No.
M159 37 Not existed
38 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace (if shield line is short) the root cause.

CHECK 8CH CAN gateway AND ADAS control unit 2 TERMINATION CIRCUIT

  1. Remove the 8CH CAN gateway and the ADAS control unit 2.

  2. Check the resistance between the 8CH CAN gateway terminals.

    8CH CAN gateway Resistance (Ω)
    Terminal No.
    37 38 Approx. 108 – 132
  3. Check the resistance between the ADAS control unit 2 terminals.

    ADAS control unit 2 Resistance (Ω)
    Terminal No.
    28 29 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 10.

NO>>

Replace the 8CH CAN gateway and/or the ADAS control unit 2.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M159 37 42 Existed
    38 41 Existed

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector terminals.

8CH CAN gateway harness connector Continuity
Connector No. Terminal No.
M159 37 38 Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Check the harness and repair the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway and the ground.

8CH CAN gateway harness connector Ground Continuity
Connector No. Terminal No.
M159 37 Not existed
38 Not existed

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Check the harness and repair the root cause.

CHECK 8CH CAN GATEWAY TERMINATION CIRCUIT

  1. Remove the 8CH CAN gateway.

  2. Check the resistance between the 8CH CAN gateway terminals.

    8CH CAN gateway Resistance (Ω)
    Terminal No.
    37 38 Approx. 108 – 132
    42 41 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 10.

NO>>

Replace the 8CH CAN gateway.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 11.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of ITS CAN communication 4 circuit.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

Its Can Communication 5 Circuit Nissan Pathfinder R53

Diagnosis Procedure

CHECK CAN DIAGNOSIS

Check the CAN diagnosis results from CONSULT to see that the ITS CAN communication 4 circuit have no malfunction.

Are the ITS CAN communication 4 circuit normal?

YES>>

GO TO 2.

NO>>

Check and repair ITS CAN communication 4 circuit.

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the control unit connectors on ITS CAN communication 5 circuit.

  4. Check the terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the around view monitor control unit harness connector and sonar control unit harness connector.

Around view monitor control unit harness connector Sonar control unit harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
M96 21 M75 39 Existed
5 40 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the around view monitor control unit harness connector terminals.

Around view monitor control unit harness connector Continuity
Connector No. Terminal No.
M96 21 5 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the around view monitor control unit and the ground.

Around view monitor control unit harness connector Ground Continuity
Connector No. Terminal No.
M96 21 Not existed
5 Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Check the harness and repair or replace (if shield line is short) the root cause.

CHECK AROUND VIEW MONITOR CONTROL UNIT AND SONAR CONTROL UNIT TERMINATION CIRCUIT

  1. Remove the around view monitor control unit and the sonar control unit.

  2. Check the resistance between the around view monitor control unit terminals.

    Around view monitor control unit Resistance (Ω)
    Terminal No.
    21 5 Approx. 108 – 132
  3. Check the resistance between the sonar control unit terminals.

    Sonar control unit Resistance (Ω)
    Terminal No.
    39 40 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 7.

NO>>

Replace the around view monitor control unit and/or the sonar control unit.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 8.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of ITS CAN communication 5 circuit.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

Chassis Can Communication 2 Circuit Nissan Pathfinder R53

Diagnosis Procedure

CHECK CAN DIAGNOSIS

Check the CAN diagnosis results from CONSULT to see that the chassis CAN communication 3 circuit have no malfunction.

Are the chassis CAN communication 3 circuit normal?

YES>>

GO TO 2.

NO>>

Check and repair chassis CAN communication 3 circuit.

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the control unit connectors on chassis CAN communication 2 circuit.

  4. Check the terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the chassis control module harness connector and ABS actuator and electric unit (control unit) harness connector.

Chassis control module harness connector ABS actuator and electric unit (control unit) harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
E12 19 E125 5 Existed
7 19 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the chassis control module harness connector terminals.

Chassis control module harness connector Continuity
Connector No. Terminal No.
E12 19 7 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the chassis control module and the ground.

Chassis control module harness connector Ground Continuity
Connector No. Terminal No.
E12 19 Not existed
7 Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Check the harness and repair or replace (if shield line is short) the root cause.

CHECK CHASSIS CONTROL MODULE AND ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) TERMINATION CIRCUIT

  1. Remove the chassis control module and the ABS actuator and electric unit (control unit).

  2. Check the resistance between the chassis control module terminals.

    Chassis control module Resistance (Ω)
    Terminal No.
    19 7 Approx. 108 – 132
  3. Check the resistance between the ABS actuator and electric unit (control unit) terminals.

    ABS actuator and electric unit (control unit) Resistance (Ω)
    Terminal No.
    5 19 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 7.

NO>>

Replace the chassis control module and/or the ABS actuator and electric unit (control unit).

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 8.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of chassis CAN communication 2 circuit.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

Drivetrain Can Communication 1 Circuit Nissan Pathfinder 5th Gen

Diagnosis Procedure

CHECK CAN DIAGNOSIS

Check the CAN diagnosis results from CONSULT to see that the drivetrain CAN communication 2 circuit has no malfunction.

Is the drivetrain CAN communication circuit 2 normal?

YES>>

GO TO 2.

NO>>

Check and repair drivetrain CAN communication 2 circuit.

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the unit connectors on drivetrain CAN communication 1 circuit.

  4. Check terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the ECM harness connector and the chassis control module harness connector.

ECM harness connector Chassis control module harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
F79 169 E12 17 Existed
165 4 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the ECM harness connector terminals.

ECM harness connector Continuity
Connector No. Terminal No.
F79 169 165 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the ECM harness connector and the ground.

ECM harness connector Ground Continuity
Connector No. Terminal No.
F79 169 Not existed
165 Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Check the harness and repair the root cause.

CHECK TERMINATION CIRCUIT

  1. Remove the ECM and the chassis control module.

  2. Check the resistance between the ECM terminals.

    ECM Resistance (Ω)
    Terminal No.
    169 165 Approx. 108 – 132
  3. Check the resistance between the chassis control module terminals.

    Chassis control module Resistance (Ω)
    Terminal No.
    17 4 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 7.

NO>>

Replace the ECM and/or the chassis control module.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 8.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of drivetrain CAN 1 communication circuit.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

Diagnostic Can Communication Circuit Nissan Pathfinder 2022

Diagnosis Procedure

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Data link connector

    • 8CH CAN gateway

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M5 5 3 Existed
    4 2 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector terminals.

8CH CAN gateway harness connector Continuity
Connector No. Terminal No.
M5 5 4 Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector and the ground.

8CH CAN gateway harness connector Ground Continuity
Connector No. Terminal No.
M5 5 Not existed
4 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace the root cause.

CHECK 8CH CAN GATEWAY TERMINATION CIRCUIT

  1. Remove the 8CH CAN gateway.

  2. Check the resistance between the 8CH CAN gateway terminals.

    8CH CAN gateway Resistance (Ω)
    Terminal No.
    5 4 Approx. 108 – 132
    3 2 Approx. 108 – 132

Is the measurement value within the specification?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the diagnostic CAN communication circuit.

NO>>

Replace the 8CH CAN gateway.