Front Suspension - Periodic Maintenance
- Front Suspension Assembly
- Wheel Alignment
Front Suspension Assembly Nissan Pathfinder
Inspection
COMPONENT PART
Check the front suspension for the following:
Check each component for looseness or play.
Inspect each component for abnormal wear or damage.
Oil Leakage Inspection
If oil (A) does not extend beyond the spring seat (B) or upper half (C) of strut/shock absorber (1), this is slight oil seepage and the strut/shock absorber should not be replaced.

If oil (A) does extend beyond the spring seat (B) or upper half (C) of strut/shock absorber (1) as shown, perform the following.

– Use a finger to touch the oil that has extended beyond the spring seat or upper half of strut/shock absorber.
– If the oil layer is thick and contains large pieces of dust and debris, replace the strut/shock absorber.
– If the oil is thin and does not contain large pieces of dust and debris, do not replace the strut/shock/ absorber.
Ball Joint Axial End Play

Set front wheels in a straight-ahead position.
Check ball joint boot for cracks or other damage. If there are cracks or other damage replace transverse link.
Move axle side of transverse link up and down by hand. Check there is no end play.

Wheel Alignment Nissan Pathfinder 5th Gen
Inspection
PRELIMINARY INSPECTION
Check the following:
Check and adjust the wheel alignment with the vehicle under unladen conditions. “Unladen conditions” means that the fuel, engine coolant, and lubricants are full; the spare tire, jack, hand tools and mats are in designated positions.
Check the tires for incorrect air pressure and excessive wear. Refer to Tire Air Pressure.
Check the wheels for run out and damage. Refer to Inspection.
Check the wheel bearing axial end play. Refer to Wheel Bearing.
Check the struts for leaks or damage.
Check each mounting point of the suspension components for any excessive looseness or damage.
Check each link, arm, and the suspension member for any damage.
Check the Nissan Pathfinder vehicle height. Refer to Wheelarch Height.
GENERAL INFORMATION AND RECOMMENDATIONS
A four-wheel thrust alignment should be performed.
This type of alignment is recommended for any NISSAN Nissan Pathfinder vehicle.
The four-wheel “thrust” process helps ensure that the vehicle is properly aligned and the steering wheel is centered.
The alignment rack itself should be capable of accepting any NISSAN Nissan Pathfinder vehicle.
The rack should be checked to ensure that it is level.
Make sure the machine is properly calibrated.
Your alignment equipment should be regularly calibrated in order to give correct information.
Check with the manufacturer of your specific equipment for their recommended Service/Calibration Schedule.
ALIGNMENT PROCESS
IMPORTANT:
Use only the alignment specifications listed in this Service Manual. Refer to Wheel Alignment.
When displaying the alignment settings, many alignment machines use “indicators” : (Green/red, plus or minus, Go/No Go). Do not use these indicators.
The alignment specifications programmed into your machine that operate these indicators may not be correct.
This may result in an ERROR.
Most camera-type alignment machines are equipped with both “Rolling Compensation” method and optional “Jacking Compensation” method to “compensate” the alignment targets or head units. “Rolling Compensation” is the preferred method.
If using the “Rolling Compensation” method, after installing the alignment targets or head units, push or pull on the rear wheel to move the Nissan Pathfinder vehicle. Do not push or pull on the vehicle body.
If using the “Jacking Compensation” method, after installing the alignment targets or head units, raise the Nissan Pathfinder vehicle and rotate the wheels 1/2 turn both ways.
Follow all instructions for the alignment machine you're using for more information.
CAMBER, CASTER AND KINGPIN INCLINATION ANGLES INSPECTION
Camber, caster, kingpin inclination angles cannot be adjusted.
Before inspection, set the front wheels onto a turning radius gauge. Set the rear wheels onto a pad that has the same height so the Nissan Pathfinder vehicle will remain horizontal.
TOTAL TOE-IN INSPECTION
Measure the total toe-in using the following procedure.
Bounce the front of vehicle up and down to stabilize the vehicle height (posture).
Push on the rear wheel to move the Nissan Pathfinder vehicle straight ahead about 5 m (16 ft).
Put a mark on base line of the tread (B) of both tires at the same height of hub center (A) . These are measuring points (C).

| : Front |
Measure the distance (A) from the rear side.

| : Front |
Push on the rear wheel to move the Nissan Pathfinder vehicle slowly ahead and to rotate the wheels 180 degrees (1/2 turn).
Measure the distance (B) from the front side.
Use the formula below to calculate total toe-in.
| Total toe-in formula | : A - B |
| Total toe-in specification | : Refer to Wheel Alignment. |
If the total toe-in is outside the specification, adjust the total toe-in. Refer to Wheel Alignment.
Adjustment
TOE-IN ADJUSTMENT
Loosen the inner socket locknut (A).

Adjust the toe using the inner socket.
Total toe-in : Refer to Wheel Alignment. Tighten the inner socket locknut. Refer to Exploded View.
After toe-in adjustment, adjust neutral position of steering angle sensor. Refer to Description.