Steering System - Dtc/circuit Diagnosis
- B24f4-12 Steering Heater Relay
- Heated Steering Wheel System
- Heated Steering Wheel Relay
B24f4-12 Steering Heater Relay Nissan Pathfinder 2022
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis name) | DTC detection condition | |
|---|---|---|---|
| B24F4-12 | STEERING HEATER RELAY (Steering heater relay) |
Diagnosis | Heated steering wheel switch is ON |
| Signal (terminal) | Heated steering wheel relay control signal | ||
| Threshold | Short to battery | ||
| Diagnosis delay time | — | ||
POSSIBLE CAUSE
Harness, fuse, or connectors
Heated steering wheel relay
A/C auto amp.
FAIL-SAFE
—
DTC Confirmation Procedure
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
Ignition switch ON.
Switch heated steering wheel ON.
Select “Self Diagnostic Result” mode of “HVAC”.
Is DTC B24F4–12 detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
DTC Diagnosis Procedure
CHECK FUSES
Check that the following fuses are not blown:
| Signal name | Fuse No. | Capacity |
|---|---|---|
| Ignition power supply | 62 | 10 A |
| 40 | 10 A |
Is the fuse blown?
YES>>Replace the blown fuse after repairing the affected circuit.
NO>>GO TO 2.
CHECK HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY) POWER SUPPLY
Ignition switch OFF.
Disconnect heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector.
Ignition switch ON.
Check voltage between heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector and ground.
(+) (-) Voltage
(Approx.)Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) Connector Terminal M90 3 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY)
Check heated steering wheel relay and back-up lamp relay (heated steering wheel relay). Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Replace heated steering wheel relay. Refer to Component Parts Location.
CHECK HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY) CONTROL SIGNAL
Ignition switch OFF.
Connect heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector.
Ignition switch ON.
Check voltage between A/C auto amp. harness connector and ground.
(+) (–) Condition Voltage
(Approx.)A/C auto amp. Connector Terminal M60 56 Ground Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) OFF Battery voltage ON 0 – 0.5 V
Is the inspection result normal?
YES>>Replace A/C auto amp. Refer to Removal and Installation.
NO>>GO TO 5.
CHECK HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY) CONTROL SIGNAL CIRCUIT
Ignition switch OFF.
Disconnect A/C auto amp. connector and heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector.
Check continuity between A/C auto amp. harness connector and heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector.
A/C auto amp. Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) Continuity Connector Terminal Connector Terminal M60 56 M90 4 Yes Check continuity between A/C auto amp. harness connector and ground.
A/C auto amp. – Continuity Connector Terminal M60 56 Ground No
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace harness.
CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to Intermittent Incident.
>>Inspection End.
Heated Steering Wheel System Nissan Pathfinder
Component Function Check
CHECK HEATED STEERING WHEEL SYSTEM
Check the heated steering wheel system. Refer to System Description.
Is the inspection result normal?
YES>>Inspection End.
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK FUSES
Check that the following fuses are not blown:
| Signal name | Fuse No. | Capacity |
|---|---|---|
| Ignition power supply | 62 | 10 A |
| 40 | 10 A |
Is the fuse blown?
YES>>Replace the blown fuse after repairing the affected circuit.
NO>>GO TO 2.
CHECK HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY) POWER SUPPLY
Ignition switch OFF.
Disconnect heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector.
Ignition switch ON.
Check voltage between heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector and ground.
(+) (-) Voltage
(Approx.)Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) Connector Terminal M90 1 Ground Battery voltage 3
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness or connector.
CHECK HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY)
Check heated steering wheel relay and back-up lamp relay (heated steering wheel relay). Refer to Component Inspection.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Replace heated steering wheel relay. Refer to Component Parts Location.
CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY) AND A/C AUTO AMP.
Ignition switch OFF.
Disconnect the heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector and A/C auto amp. harness connector.
Check continuity between heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector and A/C auto amp. harness connector.
Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) A/C auto amp. Continuity Connector Terminal Connector Terminal M90 4 M60 56 Yes Check continuity between heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector and ground.
Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) — Continuity Connector Terminal M90 4 Ground No
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace harness or connector.
CHECK HARNESS BETWEEN FRONT A/C SWITCH ASSEMBLY AND A/C AUTO AMP.
Disconnect the front A/C switch assembly harness connector.
Check continuity between front A/C switch assembly harness connector and A/C auto amp. harness connector.
Front A/C switch assembly A/C auto amp. Continuity Connector Terminal Connector Terminal M69 7 M60 68 Yes Check continuity between front A/C switch assembly harness connector and ground.
Front A/C switch assembly — Continuity Connector Terminal M69 7 Ground No
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair or replace harness or connector.
CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY) AND COMBINATION SWITCH (SPIRAL CABLE)
Disconnect the combination switch (spiral cable) harness connector.
Check continuity between heated steering wheel relay and back-up lamp relay (heated steering wheel relay) harness connector and combination switch (spiral cable) harness connector.
Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) Combination switch (spiral cable) Continuity Connector Terminal Connector Terminal M90 2 M52 41 Yes Check continuity between heated steering wheel relay harness connector and ground.
Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) — Continuity Connector Terminal M90 2 Ground No
Is the inspection result normal?
YES>>GO TO 7.
NO>>Repair or replace harness or connector.
CHECK GROUND CIRCUIT
Check continuity between combination switch (spiral cable) harness connector and ground.
| Combination switch (spiral cable) | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M52 | 42 | Ground | Yes |
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace damaged parts.
CHECK COMBINATION SWITCH (SPIRAL CABLE)
Disconnect the combination switch (spiral cable) harness connectors.
| Combination switch (spiral cable) | Continuity | |||
|---|---|---|---|---|
| Connector | Terminal | Connector | Terminal | |
| M201 | 44 | M52 | 41 | Yes |
| 43 | 42 | |||
Is the inspection result normal?
YES>>GO TO 9.
NO>>Replace combination switch (spiral cable). Refer to Removal and Installation.
CHECK HEATED STEERING WHEEL
Check heated steering wheel. Refer to Component Inspection.
Is the inspection result normal?
YES>>Check the intermittent incident. Refer to Intermittent Incident.
NO>>Replace heated steering wheel. Refer to Removal and Installation.
Component Inspection
CHECK HEATED STEERING WHEEL CONTINUITY
Check continuity between combination switch (spiral cable) terminals.
| Combination switch (spiral cable) | Condition | Continuity | |
|---|---|---|---|
| Terminals | |||
| 43 − 44 | Leather surface temperature of 68°F (20°C) or less | Yes | |
| Leather surface temperature of 86°F (30°C) or more | No | ||
Is the inspection result normal?
YES>>GO TO 2.
NO>>Replace heated steering wheel. Refer to Removal and Installation.
CHECK HEATED STEERING WHEEL RESISTANCE
Check resistance between combination switch (spiral cable) terminals.
| Combination switch (spiral cable) | Condition | Resistance (Approx.) | |
|---|---|---|---|
| Terminals | |||
| 43 − 44 | Leather surface temperature of 68°F (20°C) | 1.7 – 2.17 Ω | |
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace heated steering wheel. Refer to Removal and Installation.
Heated Steering Wheel Relay Nissan Pathfinder 2026
Component Inspection
CHECK HEATED STEERING WHEEL RELAY AND BACK-UP LAMP RELAY (HEATED STEERING WHEEL RELAY) CONTINUITY
Check continuity between heated steering wheel relay and back-up lamp relay (heated steering wheel relay) terminals.
| Heated steering wheel relay and back-up lamp relay (heated steering wheel relay) | Condition | Continuity | |
|---|---|---|---|
| Connector | Terminals | ||
| M90 | 1 − 2 | Apply 12 V direct current between terminals 3 and 4. | Yes |
| Other conditions. | No | ||
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace heated steering wheel relay. Refer to Component Parts Location.