A-pillar

In this manual: A-pillar
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
4steps
~24min
2/5difficulty
0204060801005541N·mlb·ft
Tightening torque found on this page
Done 0 of 4
  • Assembly overview - A-pillar
  • Renewing A-pillar
  • Renewing A-pillar reinforcement, part section

Assembly overview - A-pillar

Overview shown for left side of vehicle as an example

  1. A-pillar
  • Subpart
  • ⇒ Rep. gr. 51; Renewing A-pillar
  1. Separating cut
  • Parting cut can be combined with others in cases where extent of damage requires multiple cuts.
  1. Moulded foam inserts
  • ⇒ Rep. gr. 00; Moulded foam inserts
  1. Bonded area
  2. Separating cut
  • Parting cut can be combined with others in cases where extent of damage requires multiple cuts.
  1. Separating cut
  • Parting cut can be combined with others in cases where extent of damage requires multiple cuts.
  1. Separating cut
  • Parting cut can be combined with others in cases where extent of damage requires multiple cuts.
  1. Separating cut
  • Parting cut can be combined with others in cases where extent of damage requires multiple cuts.
  1. Separating cut
  • Observe replacement part blank
  1. End plate
  • Lower wing bracket
  1. Wing bracket
Volkswagen ID.4. Assembly overview - A-pillar

Assembly overview - A-pillar reinforcement

Overview shown for left side of vehicle as an example

  1. A-pillar reinforcement
  • ⇒ Rep. gr. 51; Renewing A-pillar reinforcement, part section
  1. Separating cut
  2. Connecting piece
  • Reinforcement on inside
  1. Moulded foam inserts
  • ⇒ Rep. gr. 00; Moulded foam inserts
  1. Bolt
  • (55 N·m)
  1. Bonded area
Volkswagen ID.4. Assembly overview - A-pillar reinforcement

Renewing A-pillar

WARNING

Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

  • Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
  • Use an extraction system during work.

NOTICE

Do not damage underlying reinforcements.

Rewelding of reinforcement is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

  • RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

If adhesive is applied prematurely, bond could be impaired

  • New part must be welded in within 90 minutes.

NOTICE

Bonding properties of adhesive may be impaired if adhesive components are not hardened sufficiently.

  • After bonding, the vehicle must not be moved and left at room temperature (at least 15ºC) for 8 to 10 hours.
  • During this time, the vehicle must be standing on a level surface.

Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1 .

Removal and installation are described for left side of vehicle as an example.

Removing

  • Make separating cut -2- and -3- in a straight line, as shown in illustration.
Volkswagen ID.4. Renewing A-pillar
  • Separate original joint.
  • Remove A-pillar -1-.
  • Remove any foam residue -1-.
Volkswagen ID.4. Renewing A-pillar
  • Remove remaining material.
  • Completely remove remaining adhesive.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.

Installing

Replacement parts

  • For allocation of moulded foam inserts, see ⇒ Electronic parts catalogue (ETKA)
  • For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)

Important

  • New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.
  • Transfer separating cut -2- to new part -1-, and cut in a straight line.
Volkswagen ID.4. Renewing A-pillar
  • Grind welding surfaces and bonding surfaces on new part -1- and -6- down to bare metal and clean.
  • Drill or - alternatively - punch holes of 8 mm in diameter for SG plug weld seam in new part -1- to -6-.
  • Lightly sand bonding surfaces on new part -1- from inside.
  • Prepare moulded foam inserts -1- for installation and insert.
Volkswagen ID.4. Renewing A-pillar
  • Apply 2-component body adhesive to entire surface.
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing A-pillar
  • Check fit with add-on parts.
  • Fix new part in position -1- with mole grips.
  • Weld in new part -1-, RP spot weld seam and SG plug weld seam.
  • Weld parting cuts (either MIG solder seam or SG stepped weld seam).
  • Adjust new part -2- to -5- to fit and fix in position.
  • Check fit with add-on parts.
  • Weld in new part -2- to -5- (SG plug weld seam).

Renewing A-pillar reinforcement, part section

WARNING

Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

  • Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
  • Use an extraction system during work.

NOTICE

Do not damage underlying reinforcements.

Rewelding of reinforcement is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

  • RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

If adhesive is applied prematurely, bond could be impaired

  • New part must be welded in within 90 minutes.

NOTICE

Bonding properties of adhesive may be impaired if adhesive components are not hardened sufficiently.

  • After bonding, the vehicle must not be moved and left at room temperature (at least 15ºC) for 8 to 10 hours.
  • During this time, the vehicle must be standing on a level surface.

Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1 .

Removal and installation are described for left side of vehicle as an example.

Removing

A-pillar (part section) removed ⇒ Rep. gr. 51; Renewing A-pillar.

  • Mark separating cut -2- according to dimension -a- and cut in a straight line.
Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Dimension -a- = 55 mm
  • Separate original joint.
  • Remove A-pillar reinforcement -1-.
  • Mark separating cut -2- according to dimension -a- and cut in a straight line.
Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Dimension -a- = 40 mm
  • Separate original joint.
  • Remove remainder of A-pillar reinforcement -1-.
  • Remove any foam residue -2-.
Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Separate original joint.
  • Remove remainder of hinge reinforcement -1-.
  • Remove remaining material.
Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Completely remove remaining adhesive.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.

Installing

Replacement parts

  • For allocation of moulded foam inserts, see ⇒ Electronic parts catalogue (ETKA)
  • For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)

Important

  • New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.
  • Transfer separating cut -2- to new part -1-, and cut in a straight line.
Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Transfer separating cut -4- to new part -3-, and cut in a straight line.
  • Transfer number and position of holes from removed section to new part -1-.
  • Drill or alternately punch 8 mm diameter holes for SG plug weld seam.
  • Grind welding surfaces and bonding surfaces on new part -1-, -3- and -5- down to bare metal and clean.
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Check fit with add-on parts.
  • Apply 2-component body adhesive to entire surface.
  • Weld in new part -1-, RP spot weld seam.
  • Tighten bolt -3-.
  • Prepare moulded foam inserts -1- for installation and insert.
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Check fit with add-on parts.
  • Weld in new part -1-, SG continuous weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Adapt new part -1- to fit and fix in position.

    ID.4 2021 ➤ Body repairs - Edition 12.2022 114 Rep.

Volkswagen ID.4. Renewing A-pillar reinforcement, part section
  • Check fit with add-on parts.
  • Weld in new part -1- (RP spot weld seam, SG plug weld seam and SG continuous weld seam).
  • Install A-pillar part section ⇒ Rep. gr. 51; Renewing A-pillar

Tightening torques

  • ⇒ Rep. gr. 51; Assembly overview - A-pillar reinforcement