Entry and start authorisation system

In this manual: Entry and start authorisation system
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
4steps
~24min
2/5difficulty
0102030405021N·mlb·ft
Tightening torque found on this page
Done 0 of 4
  • Overview of fitting locations - entry and start authorisation system
  • Overview of fitting locations - keyless entry system
  • Removing and installing entry and start authorisation control unit [J518]
  • Removing and installing entry and start authorisation aerials
  • Removing and installing luggage compartment aerial for entry and start system [R137]
  • Removing and installing control unit for mobile-controlled entry and start authorisation system [J1308] ID4
  • Alcohol interlock
  • Breath-alcohol-controlled immobiliser - routing and connecting wires
  • Commissioning breath-alcohol-controlled immobiliser

Overview of fitting locations - entry and start authorisation system

Overview of fitting locations - entry and start authorisation system, lefthand drive vehicles

Volkswagen ID.4. Overview of fitting locations - entry and start authorisation system, lefthand drive vehicles
  1. Control unit 2 for break-in protection - J1192-
  • ⇒ Rep. gr. 94 ; Removing and installing control unit 2 for breakin protection [J1192]/ control unit 3 for breakin protection [J1193]
  1. Control unit 3 for break-in protection - J1193-
  • ⇒ Rep. gr. 94 ; Removing and installing control unit 2 for breakin protection [J1192]/ control unit 3 for breakin protection [J1193]
  1. Interior aerial 1 for entry and start system - R138-
  • ⇒ Rep. gr. 94 ; Removing and installing interior aerial 1 for entry and start authorisation system [R138]
  1. Aerial 2 for mobile-controlled entry and start authorisation system - R416-
  • Depending on model
  • ⇒ Rep. gr. 94 ; Removing and installing aerial 2 for mobile-controlled entry and start authorisation system [R416]
  1. Control unit 5 for break-in protection - J1195-
  • ⇒ Rep. gr. 94 ; Removing and installing control unit 4 for break-in protection [J1194]/control unit 5 for break-in protection [J1195]
  1. Control unit 4 for break-in protection - J1194-
  • ⇒ Rep. gr. 94 ; Removing and installing control unit 4 for break-in protection [J1194]/control unit 5 for break-in protection [J1195]
  1. Starter button - E378-
  • ⇒ Rep. gr. 96 ; Removing and installing starter button [E378]
  1. Control unit for electronic steering column lock - J764-
  • ⇒ Running gear, axles, steering; Rep. gr. 48 ; Steering column; Removing and installing control unit for electronic steering column lock [J764]
  1. Entry and start authorisation control unit - J518-
  • ⇒ Rep. gr. 94 ; Removing and installing entry and start authorisation control unit [J518], left-hand drive vehicles
  1. Control unit for mobile-controlled entry and start authorisation system - J1308-
  • Depending on model
  • ⇒ Rep. gr. 94 ; Removing and installing control unit for mobile-controlled entry and start authorisation system [J1308]
  1. Onboard supply control unit - J519-
  • ⇒ Rep. gr. 97 ; Removing and installing onboard supply control unit [J519]

Overview of fitting locations - entry and start authorisation system, righthand drive vehicles

Volkswagen ID.4. Overview of fitting locations - entry and start authorisation system, righthand drive vehicles
  1. Control unit 3 for break-in protection - J1193-
  • ⇒ Rep. gr. 94 ; Removing and installing control unit 2 for breakin protection [J1192]/ control unit 3 for breakin protection [J1193]
  1. Control unit 2 for break-in protection - J1192-
  • ⇒ Rep. gr. 94 ; Removing and installing control unit 2 for breakin protection [J1192]/ control unit 3 for breakin protection [J1193]
  1. Entry and start authorisation control unit - J518-
  • ⇒ Rep. gr. 94 ; Removing and installing entry and start authorisation control unit [J518], right-hand drive vehicles
  1. Control unit for electronic steering column lock - J764-
  • ⇒ Running gear, axles, steering; Rep. gr. 48 ; Steering column; Removing and installing control unit for electronic steering column lock [J764]
  1. Starter button - E378-
  • ⇒ Rep. gr. 96 ; Removing and installing starter button [E378]
  1. Control unit 4 for break-in protection - J1194-
  • ⇒ Rep. gr. 94 ; Removing and installing control unit 4 for break-in protection [J1194]/control unit 5 for break-in protection [J1195]
  1. Control unit 5 for break-in protection - J1195-
  • ⇒ Rep. gr. 94 ; Removing and installing control unit 4 for break-in protection [J1194]/control unit 5 for break-in protection [J1195]
  1. Interior aerial 1 for entry and start system - R138-
  • ⇒ Rep. gr. 94 ; Removing and installing interior aerial 1 for entry and start authorisation system [R138]
  1. Onboard supply control unit - J519-
  • ⇒ Rep. gr. 97 ; Removing and installing onboard supply control unit [J519]

Overview of fitting locations - keyless entry system

Overview of fitting locations - keyless entry system, left-hand drive vehicles

Volkswagen ID.4. Overview of fitting locations - keyless entry system, left-hand drive vehicles
  1. Left aerial for entry and start authorisation - R200-
  • ⇒ Rep. gr. 94 ; Removing and installing entry and start authorisation aerial [R200]/ [R201]
  1. Right entry and start authorisation aerial - R201-
  • ⇒ Rep. gr. 94 ; Removing and installing entry and start authorisation aerial [R200]/ [R201]
  1. Interior aerial 1 for entry and start authorisation system - R138-
  • ⇒ Rep. gr. 94 ; Removing and installing interior aerial 1 for entry and start authorisation system [R138]
  1. Front passenger exterior door handle - EX7-
  • With contact sensor for front right exterior door handle - G606-
  • With exterior door handle switch, front passenger side - F547-
  • ⇒ General body repairs, exterior; Rep. gr. 57 ; Door components; Removing and installing exterior door handle [EX6]/[EX7]
  1. Luggage compartment aerial for entry and start system - R137-
  • ⇒ Rep. gr. 94 ; Removing and installing luggage compartment aerial for entry and start system [R137]
  1. Driver exterior door handle - EX6-
  • with contact sensor for front left exterior door handle - G605-
  • With exterior door handle switch, driver side - F546-
  • ⇒ General body repairs, exterior; Rep. gr. 57 ; Door components; Removing and installing exterior door handle [EX6]/[EX7]
  1. Entry and start authorisation control unit - J965-
  • ⇒ Rep. gr. 94 ; Removing and installing entry and start authorisation control unit [J965]
  1. Control unit for mobile-controlled entry and start authorisation system - J1308-
  • Depending on model
  • ⇒ Rep. gr. 94 ; Removing and installing control unit for mobile-controlled entry and start authorisation system [J1308]
  1. Aerial 1 for mobile-controlled entry and start authorisation system - R415-
  • Depending on model
  • Rep. gr. 94 ; Removing and installing aerial 1 for mobile-controlled entry and start authorisation system [R415]

Overview of fitting locations - keyless entry system, right-hand drive vehicles

Volkswagen ID.4. Overview of fitting locations - keyless entry system, right-hand drive vehicles
  1. Front passenger exterior door handle - EX7-
  • with contact sensor for front left exterior door handle - G605-
  • With exterior door handle switch, front passenger side - F547-
  • ⇒ General body repairs, exterior; Rep. gr. 57 ; Door components; Removing and installing door handle
  1. Interior aerial 1 for entry and start authorisation system - R138-
  • ⇒ Rep. gr. 94 ; Removing and installing interior aerial 1 for entry and start authorisation system [R138]
  1. Left aerial for entry and start authorisation - R200-
  • ⇒ Rep. gr. 94 ; Removing and installing entry and start authorisation aerial [R200]/ [R201]
  1. Right entry and start authorisation aerial - R201-
  • ⇒ Rep. gr. 94 ; Removing and installing entry and start authorisation aerial [R200]/ [R201]
  1. Entry and start authorisation control unit - J965-
  • ⇒ Rep. gr. 94 ; Removing and installing entry and start authorisation control unit [J965]
  1. Driver exterior door handle - EX6-
  • With contact sensor for front right exterior door handle - G606-
  • With exterior door handle switch, driver side - F546-
  • ⇒ General body repairs, exterior; Rep. gr. 57 ; Door components; Removing and installing door handle
  1. Luggage compartment aerial for entry and start system - R137-
  • ⇒ Rep. gr. 94 ; Removing and installing luggage compartment aerial for entry and start system [R137]

Assembly overview - control unit for break-in protection

Overview shown for left side of vehicle as an example

Volkswagen ID.4. Overview shown for left side of vehicle as an example
  1. Bracket for control unit 2 for break-in protection - J1192- / control unit 3 for break-in protection - J1193-
  2. Control unit 2 for breakin protection - J1192- / control unit 3 for break-in protection - J1193-
  • ⇒ Rep. gr. 94 ; Removing and installing front control unit for break-in protection
  1. Bolt
  • Qty. 2
  • 2 N·m

Removing and installing entry and start authorisation control unit [J518]

Removing and installing entry and start authorisation control unit [J518], lefthand drive vehicles

Entry and start authorisation control unit - J518- is referred to hereafter as control unit.

Removing

If control unit is renewed:

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Vehicles with footwell cover

  • Remove footwell cover on driver side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing footwell cover on driver side .

All vehicles (continued)

  • Disconnect electrical connector -2-.
  • Release locking devices -3-.
  • Swing out control unit -1- in direction of -arrow A-.
Volkswagen ID.4. Removing and installing entry and start authorisation control unit [J518], lefthand drive vehicles

Installing

Install in the reverse order of removal, observing the following:

If control unit has been renewed:

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Removing and installing entry and start authorisation control unit [J518], righthand drive vehicles

Entry and start authorisation control unit - J518- is referred to hereafter as control unit.

Removing

If control unit is renewed:

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Remove footwell vent on driver side ⇒ Heating, air conditioning system; Rep. gr. 87 ; Air duct; Removing and installing footwell vent on driver side .
  • Unscrew bolts -2-.
  • Remove control unit -1-.
  • Disconnect electrical connector -3-.
  • Remove control unit -1-.
Volkswagen ID.4. Removing and installing entry and start authorisation control unit [J518], righthand drive vehicles

Installing

Install in the reverse order of removal, observing the following:

If control unit has been renewed:

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Removing and installing entry and start authorisation aerials

Left aerial for entry and start authorisation - R200- and right aerial for entry and start authorisation - R201- are referred to hereafter as aerial.

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove front wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing and installing front wheel housing liner .
  • Disconnect electrical connector -1-.
  • Release locking lugs -2- using an 8 mm socket.
  • Remove aerial -3-.
Volkswagen ID.4. Removing and installing entry and start authorisation aerials

Installing

Install in reverse order of removal.

Removing and installing interior aerial 1 for entry and start system [R138]

The interior aerial 1 for entry and start system - R138- will henceforth be referred to as "aerial".

Removing

  • Remove centre console insert ⇒ General body repairs, interior; Rep. gr. 68 ; Centre console; Removing and installing centre console insert .
  • Release fastener -2-.
  • Remove aerial -1-.
Volkswagen ID.4. Removing and installing interior aerial 1 for entry and start system [R138]

Installing

Install in reverse order of removal.

Removing and installing luggage compartment aerial for entry and start system [R137]

Special tools and workshop equipment required

  • removal wedge set - VAS 895 015-

The luggage compartment aerial for entry and start system - R137- will henceforth be referred to as "aerial".

Removing

  • Remove lock carrier trim ⇒ General body repairs, interior; Rep. gr. 70 ; Luggage compartment trims; Removing and installing lock carrier trim .
  • Use removal wedge set - VAS 895 015- to lever off aerial -1- in direction of -arrow A-.
  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing and installing luggage compartment aerial for entry and start system [R137]

Installing

Install in reverse order of removal.

Removing and installing front control unit for break-in protection

Control unit 2 for break-in protection - J1192- and control unit 3 for break-in protection - J1193- are referred to hereafter as control unit for break-in protection.

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove front wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing and installing front wheel housing liner .
  • Disconnect electrical connector -3-.
  • Release locking devices -2-.
  • Remove control unit for break-in protection -1- in direction of -arrow-.
Volkswagen ID.4. Removing and installing front control unit for break-in protection

Installing

Install in reverse order of removal.

Removing and installing rear control unit for break-in protection

Control unit 4 for break-in protection - J1194- and control unit 5 for break-in protection - J1195- are referred to hereafter as "control unit".

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove bumper cover ⇒ General body repairs, exterior; Rep. gr. 63 ; Rear bumper; Removing and installing bumper cover .
  • Disconnect electrical connector -3-.
  • Release locking devices -2-.
  • Remove control unit -1- in direction of -arrow-.
Volkswagen ID.4. Removing and installing rear control unit for break-in protection

Installing

Install in the reverse order of removal, observing the following:

Tightening torques

  • ⇒ General body repairs, exterior; Rep. gr. 63 ; Rear bumper; Assembly overview - bumper cover

Removing and installing control unit for mobile-controlled entry and start authorisation system [J1308] ID4

Removing and installing control unit for mobile-controlled entry and start authorisation system [J1308]

Control unit for mobile-controlled entry and start authorisation system - J1308- is referred to hereafter as control unit.

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Remove footwell cover on driver side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing footwell cover on driver side .
  • Disconnect electrical connectors from control unit -1-.
  • Release locking devices -2-.
  • Pull out control unit -1- with adapter -3- in direction of -arrow-.
  • Pull off adapter -3- from control unit -1-.
Volkswagen ID.4. Removing and installing control unit for mobile-controlled entry and start authorisation system [J1308]

Installing

Install in the reverse order of removal, observing the following:

  • Insert control unit -2- into adapter -1- in direction of -arrow-.

Important

  • Markings -3- must align.
  • Adapter -1- with control unit -2- must be heard to engage in holder.
Volkswagen ID.4. Removing and installing control unit for mobile-controlled entry and start authorisation system [J1308]

Removing and installing aerial 1 for mobile-controlled entry and start authorisation system [R415] ID4

Removing and installing aerial 1 for mobile-controlled entry and start authorisation system [R415]

Aerial 1 for mobile-controlled entry and start authorisation system - R415- is referred to hereafter as aerial.

It is not possible to remove the aerial 1 for mobile-controlled entry and start authorisation system without damaging it.

Removing

  • Remove glove compartment ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment .
  • Disconnect electrical connector -2-.
  • Mark position of aerial -1-.
  • Pull off aerial -1- from air duct for defroster vent -2-.
Volkswagen ID.4. Removing and installing aerial 1 for mobile-controlled entry and start authorisation system [R415]

Installing

Install in the reverse order of removal, observing the following:

  • Remove adhesive residue from air duct for defroster vent.
  • Bond aerial to position marked during removal.

Removing and installing aerial 2 for mobile-controlled entry and start authorisation system [R416] ID4

Removing and installing aerial 2 for mobile-controlled entry and start authorisation system [R416]

Removing

  • Remove centre console insert ⇒ General body repairs, interior; Rep. gr. 68 ; Centre console; Removing and installing centre console insert .
  • Disconnect electrical connector -2-.
  • Separate aerial 2 for mobile-controlled entry and start authorisation system - R416- -1- from double-sided adhesive tape.
Volkswagen ID.4. Removing and installing aerial 2 for mobile-controlled entry and start authorisation system [R416]

Installing

Install in reverse order of removal.

Alcohol interlock

Breath-alcohol-controlled immobiliser -notes on installation

General information

Breath-alcohol-controlled immobiliser control unit is referred to hereafter as control unit.

Note

Vehicle interface according to DIN EN 50436-4:2022 and LIN version 2.0.

Note

With control unit installed, glove compartment should be empty.

Important

  • Use required retrofit kit with part number 10A.998.400.
  • Use required grommet for hole in glove compartment with part number 4B0.971.908A.
  • Vehicle with PR number GV1 (preparation for breath-alcohol- controlled immobiliser).
  • Maximum permissible current draw of control unit 7.5A.
  • Observe instructions of respective equipment manufacturer.

Change to vehicle operation

  • It is not possible for the vehicle's drive system to be engaged until the control unit enables it.
  • Changes to vehicle operation, type and meaning of signals, time response and possible malfunctions, ⇒ Equipment manufacturer instructions .

Safety information and repair notes

  • Observe safety information and repair notes from equipment manufacturer

Overview of fitting locations - interface for breath-alcohol-controlled immobiliser

Volkswagen ID.4. Left-hand drive vehicles

Left-hand drive vehicles

  1. Fuse holder C - SC-
  • ⇒ Electrical system; Rep. gr. 97 ; Relay carriers, fuse carriers, electronics boxes; Removing and installing fuse holder C [SC]
  1. Steering module carrier
  2. Coupling point for breathalcohol- controlled immobiliser
  • in glove compartment
  • Order via Electronic parts catalogue (ETKA)
  1. Data bus diagnostic interface - J533-
  • ⇒ Electrical system; Rep. gr. 97 ; Control units; Removing and installing data bus diagnostic interface [J533]
  1. Earth point right footwell
  • Renew locating element
  • Maximum 3 cables.

    Otherwise, choose parallel earth point on other side of vehicle.

  • ⇒ Current flow diagrams, fitting locations: earth points
  1. Airbag control unit - J234-
  • Free off control unit ⇒ General body repairs, interior; Rep.

    gr. 69 ; Airbag control unit; Removing and installing airbag control unit [J234]

Right-hand drive vehicles

Volkswagen ID.4. Right-hand drive vehicles
  1. Earth point left footwell
  • Renew locating element
  • Maximum 3 cables.

    Otherwise, choose parallel earth point on other side of vehicle.

  • ⇒ Current flow diagrams, fitting locations: earth points
  1. Fuse holder C - SC-
  • ⇒ Electrical system; Rep. gr. 97 ; Relay carriers, fuse carriers, electronics boxes; Removing and installing fuse holder C [SC]
  1. Coupling point for breathalcohol- controlled immobiliser
  • in glove compartment
  • Order via Electronic parts catalogue (ETKA)
  • Connect and secure according to equipment manufacturer specifications
  1. Data bus diagnostic interface - J533-
  • ⇒ Electrical system; Rep. gr. 97 ; Control units; Removing and installing data bus diagnostic interface [J533]

Block circuit diagram

Volkswagen ID.4. Block circuit diagram
  1. Coupling point for breath-alcohol-controlled immobiliser
  • Positive wire, terminal 30
  • Earth wire, terminal 31
  • LIN bus wire
  1. Control unit
  • With interface for breath-alcohol-controlled immobiliser (LIN bus wire)
  1. Earth point
  • Earth wire terminal 31 for breath-alcohol-controlled immobiliser
  1. Fuse holder
  • Positive wire terminal 30 for breath-alcohol-controlled immobiliser

Breath-alcohol-controlled immobiliser - routing and connecting wires

Important

  • Route wires in such a way that there is no risk of them becoming trapped or abraded.
  • Secure wires to wiring harness approx. every 20 cm using cable ties.

Installing

Preparing interior for installation

  • Disconnect battery ⇒ Electrical system; Rep. gr. 27 ; Battery; Disconnecting and connecting battery .

Left-hand drive vehicles

  • Free off airbag control unit ⇒ General body repairs, interior; Rep. gr. 69 ; Airbag control unit; Removing and installing airbag control unit [J234] .
  • Remove footwell vent on driver side ⇒ Heating, air conditioning system; Rep. gr. 87 ; Air duct system; Removing and installing footwell vent on driver side .

All vehicles (continued)

Right-hand drive vehicles

  • Remove lower right A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .

All vehicles (continued)

Routing and connecting LIN bus wire

  • Remove data bus diagnostic interface - J533- ⇒ Electrical system; Rep. gr. 97 ; Control units; Removing and installing data bus diagnostic interface [J533] .
  • Disconnect 40-pin connector -T40a -1- from data bus diagnostic interface - J533- -2-.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation
  • Detach LIN bus wire -1- at "PIN A34" -arrow-.⇒ Current flow diagrams, fitting locations: earth points
  • Attach wire -1- of Y adapter to "PIN A34" of 40-pin connector -T40a.
  • Install previously detached LIN bus wire -4- at "PIN 3" in socket housing -3-.
  • Install violet/black LIN bus wire -5- from retrofit kit at "PIN 1" in socket housing -3-.
  • Assemble connector housing -2- and -3- and cover with protective tube.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation
  • Install 40-pin connector -T40a -1-.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation

Left-hand drive vehicles

  • Route LIN bus wire -2- from data bus diagnostic interface - J533- -3- up to rear of glove compartment.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation

All vehicles (continued)

Right-hand drive vehicles

  • Route LIN bus wire -3- from data bus diagnostic interface - J533- -4- up to rear of glove compartment.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation

All vehicles (continued)

Routing and connecting positive wire terminal 30

  • Free off fuse carrier C - SC- -2- and pull towards rear ⇒ Electrical system; Rep. gr. 97 ; Relay carriers, fuse carriers, electronics boxes; Removing and installing fuse holder C [SC] .
  • Insert fuse carrier single fuse -1- from retrofit kit at top on fuse holder C [SC] -2-.

Important

  • Do not insert 10 A fuse just yet.
  • With wires connected, lift fuse holder C - SC- -3- slightly and turn.
  • Route positive wire from fuse carrier single fuse -2- to slot E1 -1- in fuse holder C [SC] -3-.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation

Left-hand drive vehicles

  • Guide positive wire -2- from fuse holder C - SC- -1- towards centre above steering column.
  • Guide positive wire -2- downwards to airbag control unit.
  • Route positive wire -2- behind airbag control unit to right of dash panel.
  • Route positive wire from airbag control unit up to rear of glove compartment.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation

All vehicles (continued)

Right-hand drive vehicles

  • Route positive wire -2- from fuse holder C - SC- -1- to rear of glove compartment.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation

All vehicles (continued)

Routing and connecting earth wire of terminal 31

Important

  • Maximum 3 cables. Otherwise, choose parallel earth point on other side of vehicle.
  • Replace locating element with new locating element from retrofit kit.

Left-hand drive vehicles

  • Remove lower right A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .
  • Lift front floor covering and push filler piece to one side.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation
  • Unscrew nut -5- from earth point ⇒ Current flow diagrams; Fitting locations of earth points .
  • Screw earth wire terminal 31 -4- from retrofit kit on earth point -5-.
  • Route earth wire terminal 31 -4- with LIN bus wire -2- and positive wire terminal 30 -1- behind glove compartment.

All vehicles (continued)

Right-hand drive vehicles

  • Remove lower left A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .
  • Lift front floor covering and push filler piece to one side.
  • Unscrew nut -5- from earth point ⇒ Current flow diagrams; Fitting locations of earth points .
  • Screw earth wire terminal 31 -4- from retrofit kit on earth point -5-.
  • Route earth wire terminal 31 -4- with LIN bus wire -2- and positive wire terminal 30 -1- behind glove compartment.
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation

All vehicles (continued)

Routing wiring in glove compartment

  • Drill 11 mm hole in glove compartment and attach grommet from retrofit kit -1- to hole.
  • Collate wires -2- in mesh sleeve, fit shrink-fit hose and guide approx. 25 cm into glove compartment through grommet -1-.

Note

Wires that are too long can be shortened.

  • Connect control unit in glove compartment according to specifications of equipment manufacturer and attach securely in glove compartment.
  • Continue installation in reverse order of removal
Volkswagen ID.4. Breath-alcohol-controlled immobiliser -notes on installation

Commissioning breath-alcohol-controlled immobiliser

Connecting breath-alcohol-controlled immobiliser

  • Install and connect control unit and hand unit according to specifications of equipment manufacturer.
  • Connect battery ⇒ Electrical system; Rep. gr. 27 ; Battery; Disconnecting and connecting battery .
  • Fit 10 A fuse in fuse holder C - SC- .

Updating software

Important

  • Make sure that the most recent ID software (target data container) is installed.
  • Connect vehicle diagnostic tester.
  • Select diagnosis mode.
  • Select "Adapting SVM software".
  • Carry out measures code "NRLCHO".

Commissioning breath-alcohol-controlled immobiliser

  • Perform function test according to equipment manufacturer specifications.

Dismantling breath-alcohol-controlled immobiliser

Observe specifications of equipment manufacturer.

Removing

  • Connect vehicle diagnostic tester.
  • Select diagnosis mode.
  • Select "Adapting SVM software".
  • Carry out measures code "ARLCHO".
  • Switch off ignition.
  • Remove 10 A fuse in fuse holder C - SC- .
  • Remove glove compartment cover ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment cover .
  • Remove control unit and hand unit from glove compartment.
  • Pull wiring harness out of glove compartment, attach to bulkhead and insulate.
  • Remove grommet, seal holes in glove compartment using suitable plugs.
  • Install glove compartment.