Brake servo and brake master cylinder

In this manual: Brake servo and brake master cylinder
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
17steps
~102min
4/5difficulty
010203040501410N·mlb·ft
Tightening torque found on this page
Done 0 of 17
  • Assembly overview - brake servo/brake master cylinder
  • Removing and installing brake master cylinder
  • Removing and installing brake servo
  • Removing and installing brake servo [NX6], right-hand drive vehicles

Assembly overview - brake servo/brake master cylinder

Assembly overview - brake servo/brake master cylinder, left-hand drive vehicles

Volkswagen ID.4. Assembly overview - brake servo/brake master cylinder, left-hand drive vehicles
  1. Brake line
  • Brake master cylinder/ secondary piston circuit to hydraulic unit
  • M12 x 1
  • With standard tool: 14 N·m
  • With special tools VAS 6854, VAG 1410/7 and VAG 1410/6: 12 N·m
  1. Brake line
  • Brake master cylinder/ primary piston circuit to hydraulic unit
  • M12 x 1
  • With standard tool: 14 N·m
  • With special tools VAS 6854, VAG 1410/7 and VAG 1410/6: 12 N·m
  1. Brake fluid level warning contact -F34-
  2. Cap
  3. Brake fluid reservoir
  4. Bolt
  • 4 N·m
  1. Brake servo -NX6-
  • With brake servo control unit -J539-
  • With brake pedal position sender -G100-
  • With brake pedal position sender 2 -G836-
  • ⇒ Rep. gr. 47; Removing and installing brake servo
  1. Gasket for brake servo
  • Renew after removing
  1. Nut
  • Qty. 2
  • Renew after removing
  • 20 N·m
  1. Mounting bracket with brake pedal
  • ⇒ Rep. gr. 46; Assembly overview - brake pedal
  • ⇒ Rep. gr. 46; Removing and installing mounting bracket
  1. Seal
  • Renew after removing
  1. Brake master cylinder
  • ⇒ a2.2 nd installing brake master cylinder"
  1. Bolt
  • Qty. 2
  • Renew after removing
  • M8 x 31
  • 30 N·m
  1. Plug

Assembly overview - brake servo/brake master cylinder, right-hand drive vehicles

Volkswagen ID.4. Assembly overview - brake servo/brake master cylinder, right-hand drive vehicles
  1. Cap
  2. Brake fluid reservoir
  3. Stud
  • 4 N·m
  1. Brake servo -NX6-
  • With brake servo control unit -J539-
  • With brake pedal position sender -G100-
  • With brake pedal position sender 2 -G836-
  • ⇒ Rep. gr. 47; Removing and installing brake servo
  1. Gasket for brake servo
  • Renew after removing
  1. Mounting bracket with brake pedal
  • ⇒ Rep. gr. 46; Assembly overview - brake pedal
  • ⇒ Rep. gr. 46; Removing and installing mounting bracket
  1. Nut
  • Qty. 2
  • Renew after removing
  • 20 N·m
  1. Seal
  • Renew after removing
  1. Brake master cylinder
  • ⇒ a2.2 nd installing brake master cylinder"
  1. Bolt
  • Renew after removing
  • M8 x 31
  • 30 N·m
  1. Brake line
  • Brake master cylinder/secondary piston circuit to hydraulic unit
  • M12 x 1
  • With standard tool: 14 N·m
  • With special tools VAS 6854, VAG 1410/7 and VAG 1410/6: 12 N·m
  1. Brake line
  • Brake master cylinder/primary piston circuit to hydraulic unit
  • M12 x 1
  • With standard tool: 14 N·m
  • With special tools VAS 6854, VAG 1410/7 and VAG 1410/6: 12 N·m
  1. Bolt
  • Renew after removing
  • M8 x 31
  • 30 N·m
  1. Plug
  2. Brake fluid level warning contact -F34-

Removing and installing brake master cylinder

Special tools and workshop equipment required

  • Brake filling and bleeding equipment -VAS 6860-
  • Engine bung set -VAS 6122-
  • Socket/bit set, 39-piece -VAS 6928-

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

Vehicles with vibration isolation strut

  • Remove vibration isolation strut ⇒ General body repairs, exterior; Rep. gr. 50; Lock carrier; Removing and installing vibration isolation strut

All vehicles (continued)

Left-hand drive vehicles

  • Remove battery tray ⇒ Electrical system; Rep. gr. 27; Battery; Removing and installing battery tray.

All vehicles (continued)

Right-hand drive vehicles

Remove coolant expansion tank and lay aside with coolant hoses still attached ⇒ Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220; Rep. gr. 19; Cooling system/coolant; Removing and installing coolant expansion tank.

All vehicles (continued)

  • Extract as much brake fluid as possible from brake fluid reservoir -1- using brake filling and bleeding equipment -VAS 6860- -A-.
Volkswagen ID.4. Removing and installing brake master cylinder

NOTICE

Risk of damage due to corrosion.

  • Make sure that no brake fluid gets onto electrical contacts.
  • Place sufficient lint-free cleaning cloths in area of brake servo.
  • Mark and unscrew brake lines -2- and -3- from brake master cylinder.
Volkswagen ID.4. Removing and installing brake master cylinder
  • Seal threaded holes in brake master cylinder immediately with M12 sealing plugs (assembly parts).
  • Seal brake lines with engine bung set -VAS 6122-.

Note

Fit dust caps from bleeder screws on brake lines as an alternative.

  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing and installing brake master cylinder
  • Unscrew bolts -4- using socket from Socket set, 39 piece -VAS 6928-.
  • Pull out brake master cylinder -3-.

Installing

Install in reverse order of removal, observing the following:

  • Make sure that seal and push rod are seated correctly.
  • ⇒ Rep. gr. 47; Bleed hydraulic system.
  • Carry out function "Basic setting brake servo" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Tightening torques

  • ⇒ Rep. gr. 47; Assembly overview - brake servo/brake master cylinder

Removing and installing brake servo

Removing and installing brake servo [NX6], left-hand drive vehicles

Special tools and workshop equipment required

  • Brake filling and bleeding equipment -VAS 6860-
  • Engine bung set -VAS 6122-
  • Hot air blower -VAS 1978/14A-
  • Open ring spanner insert, AF 11mm -V.A.G 1410/6-
  • Socket/bit set, 39-piece -VAS 6928-
  • Torque wrench -VAS 6854-
  • Universal joint -V.A.G 1410/7-
  • assembly tool -V.A.G 1410/8-

Brake servo -NX6- is referred to hereafter as brake servo.

For sealing plugs (assembly parts), see electronic parts catalogue (ETKA)

Volkswagen ID.4. For sealing plugs (assembly parts), see electronic parts catalogue (ETKA)

Removing

If the brake servo control unit -J539- is renewed, perform the test plan for renewal of the control unit:

  • Carry out function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Continued

  • Remove air intake unit of heater and air conditioning unit ⇒ Heating, air conditioning system; Rep. gr. 87; Front heater and air conditioning unit; Removing and installing air intake unit of heater and air conditioning unit.
  • Remove battery tray ⇒ Electrical system; Rep. gr. 27; Battery; Removing and installing battery tray.
  • Extract as much brake fluid as possible from brake fluid reservoir -1- using brake filling and bleeding equipment -VAS 6860- -A-.
Volkswagen ID.4. For sealing plugs (assembly parts), see electronic parts catalogue (ETKA)
  • Disconnect electrical connector -2- from brake fluid level warning contact -F34- and electrical connector -3- from brake servo -1-.
Volkswagen ID.4. For sealing plugs (assembly parts), see electronic parts catalogue (ETKA)

NOTICE

Risk of damage due to corrosion.

  • Make sure that no brake fluid gets onto electrical contacts.
  • Place sufficient lint-free cleaning cloths in area of brake servo.
  • Mark and unscrew brake lines -2- and -3- from brake master cylinder.
Volkswagen ID.4. Removing and installing brake servo
  • Seal threaded holes in brake master cylinder immediately with M12 sealing plugs (assembly parts).
  • Seal brake lines with engine bung set -VAS 6122-.

Note

Fit dust caps from bleeder screws on brake lines as an alternative.

  • ⇒ Rep. gr. 46; Separating brake pedal from and joining to brake servo.
  • Unscrew nuts -3- and -4- for brake servo from mounting bracket.
Volkswagen ID.4. Removing and installing brake servo

NOTICE

Risk of damage to the plenum chamber bulkhead due to improper separation of the bonded joint.

  • Never lever the brake servo off the plenum chamber bulkhead to separate the bonded joint.
  • If brake servo gets jammed in holes, loosen nuts -1- and -2- on mounting bracket.
  • Pull brake servo off bulkhead, and remove it from vehicle.

Important

  • Make sure that the brake lines from brake master cylinder are not bent.
  • Remove adhesive residue -arrows- from brake servo -2- and from bulkhead -1-.
Volkswagen ID.4. Removing and installing brake servo
  • To do so, apply gentle heat from hot air blower -VAS 1978/14A- to the adhesive residue and pull it off.
  • Thoroughly clean surfaces.

Installing

Install in reverse order of removal, observing the following:

  • Renew gasket between brake servo and bulkhead.
  • Insert brake servo, and screw on nuts by hand.
  • ⇒ Rep. gr. 46; Separating brake pedal from and joining to brake servo.
  • Use assembly tool -V.A.G 1410/8- to fit brake lines.
Volkswagen ID.4. Removing and installing brake servo

Important

  • Keep brake lines straight when fitting them.
  • Tighten brake servo.
  • ⇒ Rep. gr. 47; Bleed hydraulic system.

    If

If the brake servo control unit -J539- has been renewed, conclude the test plan for renewal of the control unit:

  • Conclude function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Continued

Tightening torques

Assembling special tools for tightening brake lines

Volkswagen ID.4. Removing and installing brake servo
  1. Torque wrench -VAS 6854-
  2. Universal joint -V.A.G 1410/7-
  3. Open ring spanner insert AF 11 -V.A.G 1410/6-
  • ⇒ Rep. gr. 47; Assembly overview - brake servo/brake master cylinder, left-hand drive vehicles
  • ⇒ Electrical system; Rep. gr. 27; Battery; Assembly overview - battery
  • ⇒ Heater and air conditioning unit; Rep. gr. 87; Front heater and air conditioning unit; Assembly overview - air intake unit of heater and air conditioning unit

Removing and installing brake servo [NX6], right-hand drive vehicles

Special tools and workshop equipment required

  • Brake filling and bleeding equipment -VAS 6860-
  • Engine bung set -VAS 6122-
  • Hot air blower -VAS 1978/14A-
  • Open ring spanner insert, AF 11mm -V.A.G 1410/6-
  • Socket/bit set, 39-piece -VAS 6928-
  • Torque wrench -VAS 6854-
  • Universal joint -V.A.G 1410/7-
  • assembly tool -V.A.G 1410/8-

Brake servo -NX6- is referred to hereafter as brake servo.

For sealing plugs (assembly parts), see electronic parts catalogue (ETKA)

Volkswagen ID.4. For sealing plugs (assembly parts), see electronic parts catalogue (ETKA)
  1. Plugs M10
  2. Plugs M12

Removing

If the brake servo control unit -J539- is renewed, perform the test plan for renewal of the control unit:

  • Carry out function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Continued

  • Remove air intake unit of heater and air conditioning unit ⇒ Heating, air conditioning system; Rep. gr. 87; Front heater and air conditioning unit; Removing and installing air intake unit of heater and air conditioning unit.

For vehicles with heat pump valve unit

  • Remove heat pump valve unit ⇒ Heating, air conditioning; Rep. gr. 87; Heat pump valve unit; Removing and installing heat pump valve unit.

All vehicles (continued)

  • Extract as much brake fluid as possible from brake fluid reservoir -1- using brake filling and bleeding equipment -VAS 6860-.
Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles
  • Disconnect electrical connector -2- from brake fluid level warning contact -F34- of brake fluid reservoir -1-.
Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles
  • Remove stud -2-.
Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles
  • Pull brake fluid reservoir -1- upwards out of brake master cylinder

NOTICE

Risk of damage due to corrosion.

  • Make sure that no brake fluid gets onto electrical contacts.
  • Place sufficient lint-free cleaning cloths in area of brake servo.
  • Unscrew brake lines -2- and -3- from brake master cylinder -1-.
Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles
  • Seal threaded holes in brake master cylinder immediately with M12 sealing plugs (assembly parts).
  • Seal brake lines with engine bung set -VAS 6122-.

Note

Fit dust caps from bleeder screws on brake lines as an alternative.

  • ⇒ Rep. gr. 46; Separating brake pedal from and joining to brake servo.
  • Unscrew nuts -3- and -4- for brake servo from mounting bracket.
Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles

NOTICE

Risk of damage to the plenum chamber bulkhead due to improper separation of the bonded joint.

  • Never lever the brake servo off the plenum chamber bulkhead to separate the bonded joint.
  • If brake servo gets jammed in holes, loosen nuts -1- and -2- on mounting bracket.
  • Disconnect electrical connector -1- from brake servo -2-.
Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles
  • Remove brake servo from vehicle.

Important

  • Make sure that the brake lines from brake master cylinder are not bent.
  • Remove adhesive residue -arrows- from brake servo -2- and from bulkhead -1-.
Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles
  • To do so, apply gentle heat from hot air blower -VAS 1978/14A- to the adhesive residue and pull it off.
  • Thoroughly clean surfaces.

Installing

Install in reverse order of removal, observing the following:

  • Renew gasket between brake servo and bulkhead.
  • Insert brake servo, and screw on nuts by hand.
  • ⇒ Rep. gr. 46; Separating brake pedal from and joining to brake servo.
  • Use assembly tool -V.A.G 1410/8- to fit brake lines.
Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles

Important

  • Keep brake lines straight when fitting them.
  • Tighten brake servo.
  • ⇒ Rep. gr. 47; Bleed hydraulic system.

If the brake servo control unit -J539- has been renewed, conclude the test plan for renewal of the control unit:

  • Conclude function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Continued

Tightening torques

Assembling special tools for tightening brake lines

Volkswagen ID.4. Removing and installing brake servo [NX6], right-hand drive vehicles
  1. Torque wrench -VAS 6854-
  2. Universal joint -V.A.G 1410/7-
  3. Open ring spanner insert AF 11 -V.A.G 1410/6-
  • ⇒ Rep. gr. 47; Assembly overview - brake servo/brake master cylinder, right-hand drive vehicles