Suspension strut, shock absorber, spring

In this manual: Suspension strut, shock absorber, spring
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
34steps
~204min
4/5difficulty
0204060801005037N·mlb·ft
Tightening torque found on this page
Done 0 of 34
  • Exploded view - shock absorber
  • Assembly overview - spring
  • Removing and installing shock absorber
  • Renewing shock absorber
  • Removing and installing spring
  • Renewing spring

Exploded view - shock absorber

The exploded view here applies to the left side of the vehicle.

Volkswagen ID.4. Exploded view - shock absorber
  1. Shock absorber
  • ⇒ Rep. gr. 42 ; Removing and installing shock absorber
  1. Bolt
  • 2x
  • Renew after removing
  • M 10 x 35
  • 50 N·m +90º
  1. Cover
  2. Nut
  • Renew after removing
  • M10
  • 25 N·m
  1. Shock absorber mounting
  2. Bump stop
  3. Cable tie
  • Renew after removing
  1. Protective tube
  2. Nut
  • Renew after removing
  • M 12 x 1.5
  • 70 N·m +180º
  1. Bolt
  • Renew after removing
  • M 12 x 1.5 x 90

Assembly overview - spring

The overview is shown for the left side of vehicle as an example.

Volkswagen ID.4. Assembly overview - spring
  1. Shock absorber
  • ⇒ Rep. gr. 42 ; Removing and installing shock absorber
  1. Bolt
  • 2x
  • Renew after removing
  • M 10 x 35
  • 50 N·m +90º
  1. Cover
  2. Nut
  • Renew after removing
  • M10
  • 25 N·m
  1. Shock absorber mounting
  2. Bump stop
  3. Cable tie
  • Renew after removing
  1. Protective tube
  2. Nut
  • Renew after removing
  • M 12 x 1.5
  • 70 N·m +180º
  1. Bolt
  • Renew after removing
  • M 12 x 1.5 x 90

Removing and installing shock absorber

The overview is shown for the left side of vehicle as an example.

Volkswagen ID.4. Removing and installing shock absorber
  1. Spring
  • Depending on equipment/ version
  • Allocation ⇒ Electronic parts catalogue (ETKA)
  • ⇒ Rep. gr. 42 ; Removing and installing spring
  1. Spring seat
  2. Support
  3. Spring seat
  4. Spring control arm
  • ⇒ Rep. gr. 42 ; Assembly overview - spring control arm
  • ⇒ Rep. gr. 42 ; Removing and installing spring control arm
  1. Retaining clip
  2. Guides

Removing and installing shock absorber

Special tools and workshop equipment required

  • engine and gearbox jack - VAS 6931-

Removing

Removal and installation are described for the left side of vehicle as an example.

  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • ⇒ Rep. gr. 42 ; Secure vehicle to support arms of lifting platform .
  • Unbolt rear left vehicle level sender - G76- from spring control arm ⇒ Rep. gr. 43 ; Removing and installing rear vehicle level sender [G76]/[G77] .

Vehicles with adaptive chassis control

  • Disconnect electrical connector -3- on rear left shock absorber damping adjustment valve - N338- .
  • Pull electrical wire -arrow- off retainer on shock absorber -2-.
Volkswagen ID.4. Removing and installing shock absorber

All vehicles (continued)

  • Position engine and gearbox jack - VAS 6931- under spring control arm, and push upwards.
  • Unscrew bolts -arrows- for shock absorber -1-.
Volkswagen ID.4. Removing and installing shock absorber
  • Unscrew nut -4-.
  • Pull out bolt -2-.
  • Press together shock absorber -1-.
  • Guide shock absorber -1- out of spring control arm -3-.
Volkswagen ID.4. Removing and installing shock absorber

Installing

Install in reverse order of removal, observing the following:

Important

  • The shock absorber must be bolted to the spring control arm only in unladen position ⇒ Rep. gr. 42 ; Raising wheel bearing assembly to unladen position .
  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Tightening torques

  • ⇒ Rep. gr. 42 ; Assembly overview - shock absorber
  • ⇒ Rep. gr. 43 ; Assembly overview - rear vehicle level senders

Renewing shock absorber

Special tools and workshop equipment required

  • Extension - T10001/14-
  • Extension - T10001/3-
  • Ratchet - T10001/11-
  • Suspension strut support clamp - V.A.G 1752/20-
  • Torque wrench - V.A.G 1331-
  • shock absorber set - T10001-
  • suspension strut support clamp - V.A.G 1752/20-

Remove shock absorber ⇒ Rep. gr. 42 ; Removing and installing shock absorber .

Dismantling shock absorber

  • Clamp suspension strut support clamp - V.A.G 1752/20- in a vice.
  • Clamp shock absorber into suspension strut support clamp - V.A.G 1752/20- .
  • Lever cover -1- off shock absorber mounting -2-.
Volkswagen ID.4. Renewing shock absorber
  • Fit tools from shock absorber set - T10001- as shown in illustration, and loosen threaded connection for shock absorber mounting.
  1. Commercially available ratchet
  2. Ratchet - T10001/11-
  3. Shock absorbers
  4. Suspension strut support clamp - V.A.G 1752/20-
  5. Extension - T10001/3-
  6. Extension - T10001/14-
    Volkswagen ID.4. Renewing shock absorber
  • Open cable tie -5-.
  • Unscrew nut -3-.
  • Pull shock absorber mounting -2- off shock absorber -1-.
  • Remove protective tube -1- from shock absorber mounting -2-.
  • Remove protective tube -1-.
Volkswagen ID.4. Renewing shock absorber

Assembling shock absorber

  • Fit tools from shock absorber set - T10001- as shown in illustration, and tighten threaded connection. When doing this, counterhold using ratchet.
  1. Tool insert - T10001/14-
  2. Commercially available ratchet
  3. Torque wrench - V.A.G 1331-
  4. Nut
  5. Shock absorber mounting
  6. Piston rod
  7. Extension - T10001/3-
  8. Ring spanner insert AF 21, commercially available
    Volkswagen ID.4. Renewing shock absorber
  • Insert stop buffer -1- to stop into shock absorber mounting -2-.
  • Make sure that seal -3- is firmly seated.
Volkswagen ID.4. Renewing shock absorber
  • Push protective tube -1- to stop onto shock absorber mounting -2-.
  • Fit and secure cable tie -3-.

Important

  • The fastener -arrow- of the cable tie -3- must be located within area -a-.
  • Closure -arrow- of cable tie must point outwards when shock absorber is installed.
Volkswagen ID.4. Renewing shock absorber
  • Install cover -1- to shock absorber mounting -2-, and ensure that it is seated firmly.
Volkswagen ID.4. Renewing shock absorber

Tightening torques

  • ⇒ Rep. gr. 42 ; Assembly overview - shock absorber

Removing and installing spring

Special tools and workshop equipment required

  • Spreader device - VAS 6274/8-
  • Supplement set - VAS 6274/12-
  • Supplement set - VAS 6274/15A-
  • Thrust plates - VAS 6274/16-
  • spring compressing system - VAS 6274-

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • ⇒ Rep. gr. 42 ; Secure vehicle to support arms of lifting platform .
  • Remove stone deflector for spring control arm ⇒ Rep.

    gr. 42 ; Removing and installing stone deflector for spring control arm .

  • Remove rear centre underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear centre underbody cladding .
  • Remove rear underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear underbody cladding .

Vehicles with rear left vehicle level sender - G76-

  • Unbolt rear left vehicle level sender - G76- from spring control arm ⇒ Rep. gr. 43 ; Removing and installing rear vehicle level sender [G76]/[G77] .

All vehicles (continued)

Preparing spreader device for rear suspension link:

  • Screw threaded spindle -1- from spreader device - VAS 6274/8- into plastic-padded plate -2- from spreader device - VAS 6274/8- .
  • Screw support plate - VAS 6274/15-8- -A- onto threaded spindle -1-.
  • Screw in gripping rod included with spreader device - VAS 6274/8- -C-.

Important

  • Please pay attention to the relevant side of the vehicle.
Volkswagen ID.4. Removing and installing spring

All vehicles (continued)

  • Position support plate -A- on longitudinal member -1-.
  • Fit support plate -B- onto suspension link at upper front -2-.
  • Align tools between upper front suspension link -2- and longitudinal member -1- via gripping rod -1-.
  • Turn threaded spindle until both support plates make contact.
Volkswagen ID.4. Removing and installing spring
  • Push slide lock -2- in direction of -arrow-.
  • Secure locating element -4- to thrust plate with slide lock - VAS 6274/16-2- -1- using bolts -3-.

Important

  • Tighten bolts -3- to 10 N·m.
Volkswagen ID.4. Removing and installing spring
  • Insert thrust plate with slide lock - VAS 6274/16-2- -F- into spring -1- at bottom.

Important

  • Plastic support must face downwards.
  • Turn thrust plate with slide lock -F- upwards at spring -1-.
Volkswagen ID.4. Removing and installing spring
  • Insert 69 mm piston - VAS 6274/12-6- -D- into thrust plate with slide lock -F-.

Important

  • Markings on piston -D- and thrust plate with slide lock -Fmust be offset relative to one another by 90º.
  • Push piston -D- through thrust plate with slide lock -F-.
Volkswagen ID.4. Removing and installing spring
  • Turn piston -D- by 90º.
  • Pull piston -D- downwards into guides on thrust plate with slide lock -F-.
Volkswagen ID.4. Removing and installing spring

Important

  • Markings -arrows- must align properly.
  • Push slide lock -2- to stop in direction of -arrow A-. This will fix piston -D- in position.
  • Turn thrust plate with slide lock -F- as far as possible upwards on spring coils -1-.
  • Make sure when doing this that plastic support rests against spring coils -1-.

NOTICE

Risk of damage to spindle due to lacking or wrong grease.

  • Apply a thin coat of molybdenum disulfide to the front area of the spindle.
  • Apply a thin coat of molybdenum disulfide -1- to the front area of the spindle -2-. For allocation, refer to ⇒ Operating manual of spring compressing system - VAS 6274- .
Volkswagen ID.4. Removing and installing spring
  • Guide spindle - VAS 6274/15-1A- -E- into spring -1-, and screw into piston -D-.
Volkswagen ID.4. Removing and installing spring
  • Insert thrust plate with swivel mounting - VAS 6274/16-1- -M- into spring -1-.

Important

  • Plastic support must face upwards.
Volkswagen ID.4. Removing and installing spring
  • Turn thrust plate with swivel mounting -M- upwards at spring -1-.
  • Guide hexagon of spindle -E- through hole in thrust plate with swivel mounting -M-.
  • Guide spindle -E- with socket with ball head (AF8) - VAS 6274/15-3- .
  • Unscrew spindle -E- as far as possible.

Important

  • Shank - without spindle threads - -E- must be located below thrust plate with swivel mounting -M-.
Volkswagen ID.4. Removing and installing spring
  • Position spindle attachment - VAS 6274/15-2A- -G- on spindle -E-.
  • Turn thrust plate with swivel mounting -M- as far as possible downwards at spring -1-.
  • Turn thrust plate with swivel mounting -M- upwards at spring coil -1-.
  • Align spindle attachment -G- in thrust plate with swivel mounting -M-.

Important

  • Make sure that spindle attachment -G- makes proper contact with guide of thrust plate with swivel mounting -M-.
Volkswagen ID.4. Removing and installing spring
  • Align thrust plate with slide lock -F- and thrust plate with swivel mounting -M-.

Important

  • Arrow on thrust plate with swivel mounting -M- must face in direction of travel.

Important

  • Make sure that spring is properly seated in thrust plates.
  • Secure locating element -3- with bracket -7- to thrust plate with swivel mounting -M- -5-.

Important

  • Tighten bolts -6- to 10 N·m.
  • Connect thrust plate with swivel mounting -M- and thrust plate with slide lock -F- via brackets -5- and bolts -4-.

Important

  • Tighten bolts -4- to 10 N·m.
Volkswagen ID.4. Removing and installing spring
  • Position socket with ball head (AF8) - VAS 6274/15-3- -K- at spindle -E-.

Important

  • Make sure that spindle attachment -G- is correctly seated in swivel mounting of thrust plate -M-.
  • Make sure that spring -1- is properly seated in thrust plate with swivel mounting -M-.
  • Tighten spindle -E- by hand.
  • Insert counter-hold tool - VAS 6274/7- -N- into thrust plate with swivel mounting -M-.
  • Tension spring -1- using socket wrench -K- while counterholding with counter-hold tool -N-.
Volkswagen ID.4. Removing and installing spring
  • Compress spring -1- until support -2- can be removed.
Volkswagen ID.4. Removing and installing spring
  • Carefully lever spring -1- with spring seat -2- off spring control arm -3-.
  • Remove spring -1- with tools.
Volkswagen ID.4. Removing and installing spring

Installing

Install in reverse order of removal, observing the following:

  • Insert lug of spring seat -2- into hole in spring control arm -3-.
Volkswagen ID.4. Removing and installing spring

Renewing spring

Special tools and workshop equipment required

  • Spreader device - VAS 6274/8-
  • Supplement set - VAS 6274/12-
  • Supplement set - VAS 6274/15A-
  • Thrust plates - VAS 6274/16-
  • foot pump - VAS 6179-
  • hydraulic tensioning device - VAS 6274/9-

Removing

  • Remove spring ⇒ Rep. gr. 42 ; Removing and installing spring .
  • Connect foot pump - VAS 6179- to hydraulic tensioning device - VAS 6274/9- .
  • Check nuts -arrows- on hydraulic tensioning device - VAS 6274/9- -L- for secure fit.
  • Attach centring disc of spring mounting - VAS 6274/15-6A- -I- to tensioning device -L-.
Volkswagen ID.4. Renewing spring

Important

  • Make sure that recess of centring disc -I- faces towards vehicle side L or R, respectively, and that locating element is fitted at top.
  • Secure centring disc -9- with bolt -1-.
  • Place adapter plate with magnets - VAS 6274/15-5- -H- onto flexible mounting, making sure that magnetic holder is correctly seated.
  • Insert spring -1- with tools into tensioning device -L-.

Important

  • Make sure that guides on mounting -1- are located in holes of centring disc -I-.
  • Hold spring in this position.
  • Connect foot pump -L- to tensioning device.
  • Withdraw piston of tensioning device -L- until spring -1- is securely fitted.
Volkswagen ID.4. Renewing spring

Important

  • Do not tension spring -1-.
  • Spring -1- must be seated correctly at guide of adapter plate -H-.
  • Determine and make note of dimension -a-.
  • Mark installation position of thrust plate with slide lock - VAS 6274/16-2- -F- and thrust plate with swivel mounting - VAS 6274/16-1- -M- on spring -1-.
Volkswagen ID.4. Renewing spring
  • Fit centring sleeve - VAS 6274/15-7- -J- in position.
  • Position socket with ball head (AF8) - VAS 6274/15-3- -K- on spindle 130 mm (AF19) - VAS 6274/15-1A- -E-.
  • Relieve tension from spring -1- via socket -K- at tensioning device -L-.
  • Move back piston of tensioning device -L- using foot pump.
  • Make sure that spring -1- is properly seated in tensioning device -L-.
  • Relieve tension from spring -1- via socket -K- in tensioning device -L-.
  • Move piston of tensioning device -L- further back via foot pump.
  • Detach tools.

Installing

Install in reverse order of removal, observing the following:

  • Insert spring -1- into tensioning device -L-.

Important

  • Markings must be transferred to new coil spring.
  • Make sure that guides on mounting -1- are located in holes of centring disc -I-.
  • Hold spring in this position.
  • Connect foot pump -L- to tensioning device.
  • Withdraw piston of tensioning device -L- as far as spring -1-.
Volkswagen ID.4. Renewing spring

Important

  • Spring -1- must NOT be tensioned.
  • Make sure that spring -1- is properly seated on guide of adapter plate -M-.
  • Retract piston of tensioning device -L- until spring -1- is securely fitted.
  • Insert thrust plate -F- in installation position.
  • Move 69 mm piston - VAS 6274/12-6- -D- through thrust plate -F-.
  • Insert piston -D- into thrust plate -F-.
Volkswagen ID.4. Renewing spring

Important

  • Markings -arrow- on piston -D- and thrust plate -F- must be offset 90ºrelative to one another.
  • Turn piston -D- by 90º.
Volkswagen ID.4. Renewing spring
  • Pull piston -D- downwards into guides on thrust plate -F-.

Important

  • Markings -arrows- must align properly.
  • Insert thrust plate -M- observing markings for orientation.
  • Screw spindle -E- into piston -D- using socket with ball head (AF8) - VAS 6274/15-3- .
  • Attach locating element.

Important

  • Tighten bolts to 10 N·m.
  • Push slide lock -2- to stop in direction of -arrow A-. This will fix piston -D- in position.
Volkswagen ID.4. Renewing spring
  • Push spindle attachment - VAS 6274/15-2A- -G- onto spindle -E-.
  • Screw spindle -E- further into piston -D-.
  • Screw in spindle -E- until spindle attachment -G- rests against thrust plate -M-.
  • Make sure that spindle attachment -G- is correctly seated in hole of thrust plate -M-.
Volkswagen ID.4. Renewing spring
  • Fit centring sleeve - VAS 6274/15-7- -J- in position.
  • Bring socket -K- in position on spindle -E-.

Important

  • Spring -1- must be properly seated in tensioning device -L-.
  • Turn socket -K- 2 turns.
  • Turn socket -K- far enough to make sure that spring -1- cannot slip out of tensioning device -L-.
Volkswagen ID.4. Renewing spring

Important

  • Spring -1- and tools must be seated correctly.
  • Operate foot pump, and slightly tighten spring -1- via piston of tensioning device -L-.
  • Tension spring -1- via spindle -E-. Keep retracting piston of tensioning device -L- over and over again.
Volkswagen ID.4. Renewing spring
  • Tension spring -1- until dimension a determined beforehand is obtained.
  • Move back piston of tensioning device -L- via foot pump.
  • Hold spring -1- in place.
  • Remove spring -1- with tools from tensioning device -L-.
  • Install spring ⇒ Rep. gr. 42 ; Removing and installing spring .