Sliding sunroof

In this manual: Sliding sunroof
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
8steps
~48min
2/5difficulty
010203040505.54N·mlb·ft
Tightening torque found on this page
Done 0 of 8

Assembly overview - glass panel

  1. Glass panel
  • ⇒ Rep. gr. 60 ; Removing and installing glass panel
  1. Outer bonding surface
  2. Centre bonding surface
  • Fitted on selected models
  1. Spacer
  • Depending on equipment/ version
  1. Centring pin
Volkswagen ID.4. Assembly overview - glass panel
  • Assembly overview - sun blind
  • Removing and installing glass panel
  • Removing and installing frame with sun blind
  • Removing and installing sun blind
  • Removing and installing sun blind drive unit VX455
  • Removing and installing sun blind cables

Assembly overview - sun blind

Volkswagen ID.4. Assembly overview - sun blind
  1. Side frame section
  • Part of frame with sun blind
  • ⇒ Rep. gr. 60 ; Removing and installing frame with sun blind
  1. Bolt
  • Qty. 4
  • Renew after removing
  • 5,5 N·m
  1. Bolt
  • Qty. 2
  • Renew after removing
  • 5,5 N·m
  1. Rear frame section
  • Part of frame with sun blind
  • ⇒ Rep. gr. 60 ; Removing and installing frame with sun blind
  1. Sun blind
  • ⇒ Rep. gr. 60 ; Removing and installing sun blind
  1. Slide
  2. Nut
  • Qty. 13
  • Renew after removing
  • Specified torque and tightening sequence
  1. Bolt
  • Qty. 4
  • Renew after removing
  • 5,5 N·m
  1. Sun blind cable
  • ⇒ Rep. gr. 60 ; Removing and installing sun blind cables
  1. Roof system control unit - J1355-
  • ⇒ Rep. gr. 60 ; Removing and installing roof system control unit J1355
  • ⇒ Rep. gr. 60 ; Adapting roof system adjustment control unit J1355
  1. Electrical connector
  2. Sun blind drive unit - VX455-
  • With Hall sender 1 for sun blind motor - G1193-
  • With Hall sender 2 for sun blind motor - G1194-
  • With sun blind motor - V758-
  • ⇒ Rep. gr. 60 ; Removing and installing sun blind drive unit VX455
  1. Spring plate
  2. Bolt
  • Qty. 3
  • 4 N·m
  1. Front frame section
  • Part of frame with sun blind
  • ⇒ Rep. gr. 60 ; Removing and installing frame with sun blind
  1. Clip
  • Qty. 7
Volkswagen ID.4. Assembly overview - sun blind

Removing and installing glass panel

Special tools and workshop equipment required

  • cutting cord - VAS 861 001/1A-
  • hot air blower - V.A.G 1416-
  • setting gauge - 3371-
  • suction lifter - V.A.G 1344-
  • window removal kit - VAS 861 001A

CAUTION

Risk of injury to hands and eyes due to glass splinters.

Danger of cutting yourself.

  • Put on safety goggles.
  • Put on protective gloves.

NOTICE

Risk of damage to surfaces of components.

  • Mask off surrounding components in the visible area with commercially available adhesive tape.

Removal is described using window removal kit - VAS 861 001A- .

Removing

  • Open sun blind.
  • Using commercially available adhesive tape, form a stop 3 cm from the pointed end of the awl -4- from window removal set - VAS 861 001A- .
  • Insert cutting cord - VAS 861 001/1A- -2- in awl -4-.
Volkswagen ID.4. Removing and installing glass panel
  • Using commercially available adhesive tape, form a stop 3 cm from the pointed end of the awl -4- from window removal set - VAS 861 001A- .
  • Insert cutting cord - VAS 861 001/1A- -2- in awl -4-.

NOTICE

Penetrating adhesive bead with awl Damage to paintwork on body flange

  • Mask off exit area of awl -4- on body flange using adhesive tape.
  • A second person exposes the exit area of the glass panel seal on the outside at the penetration point using a commercially available plastic wedge and monitors the penetration.
  • Observe stop on awl -4- during penetration.
Volkswagen ID.4. Removing and installing glass panel
  • Pierce adhesive bead with awl -4- from inside to outside, and pull through cutting cord -2- towards outside.
  • Coat seal of glass panel -1- with soapy solution.
  • Lay cutting cord -2- under glass panel around entire circumference -1- while at the same time clearing off glass panel seal -1- using commercially available plastic wedge.
  • Insert cutting cord -2- under glass panel seal -1-.
  • Press down windscreen seal using commercially available plastic wedge.
  • Insert cutting cord -2- between glass panel -1- and windscreen with threading-in aid.
  • Mask off contact surface of cutting cord -1- on hinge -2- using commercially available adhesive tape.
  • Secure outer end of cutting cord -1- on left hinge -2- -arrow-
Volkswagen ID.4. Removing and installing glass panel
  • Secure cutting out device -3- to inside of glass panel -1- at front left.
  • Insert cutting cord -2- into cutting out device -3-.
  • Tension cutting cord -2- with cutting out device -3-.

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Cut free side section of glass panel -1- in direction of -arrowusing cutting cord -2- while having the second person guide cutting cord -2- past components.
Volkswagen ID.4. Removing and installing glass panel

Important

  • The aid of an additional person is required for the subsequent work steps.

Note

Glass panel -1- can also be reused without centring pin -2-.

  • Cut through adhesive bead around centring pin -2- while having the second person guide cutting cord -2- past components.
Volkswagen ID.4. Removing and installing glass panel
  • Secure cutting out device -3- to inside of glass panel -1- at front right.

Note

There are two adhesive beads in the front area between the glass panel -1- and roof cross member. Greater force is necessary when cutting through in these areas.

  • Heat up glass panel -1- in area of adhesive beads to 40 ºC (104 ºF) using hot air blower - V.A.G 1416- .

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Cut free front section of glass panel -1- in direction of -arrowusing cutting cord -2- while having the second person guide cutting cord -2- past components.
Volkswagen ID.4. Removing and installing glass panel
  • Secure cutting out device -2- to inside of glass panel -1- at rear right.

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Cut free side section of glass panel using cutting cord -3- in direction of -arrow- while having the second person guide cutting cord -3- past components.
Volkswagen ID.4. Removing and installing glass panel
  • Secure cutting out device -2- to inside of glass panel -1- at rear right.

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Cut free rear section of glass panel using cutting cord -3- in direction of -arrow- while having the second person guide cutting cord -3- past components.
Volkswagen ID.4. Removing and installing glass panel

Important

  • The aid of four additional persons is required for the subsequent work steps.
  • Lift glass panel out of vehicle using two suction lifters - V.A.G 1344- .

Installing

Undamaged glass panel

  • ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Preparing undamaged windows for installation .

All vehicles (continued)

New glass panel

Note

Bonding surface is marked on glass panel.

  • Clean bonding surfaces, let them dry, and apply primer ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Preparing new windows for installation .

All vehicles (continued)

  • ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Preparing body flange for installation .
  • Observe ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Installation instructions for bonded windows .
  • Observe ⇒ Rep. gr. 60 ; Minimum drying time for bonded glass panels .

Glass panel -1- can also be installed without spacers -3

Important

  • Outlet nozzle of cartridge ⇒ Electronic parts catalogue (ETKA) must be adapted using suitable workshop equipment to ensure bead cross-section as per specification.
  • Apply window adhesive -2- to marked bonding surface of glass panel -1-.

Dimensions for cross-section of adhesive bead:

  • Dimension -a-: 8 +- 2 mm
  • Dimension -b-: 13.5 +- 1.5 mm
Volkswagen ID.4. Removing and installing glass panel
  • Bond windscreen seal sealing lip to windscreen using commercially available adhesive tape.

Important

  • The aid of four additional persons is required for the subsequent work steps.
  • Insert glass panel -1- into roof aperture -3- using suction lifter - V.A.G 1344- .

Important

  • Glass panel -1- must be fitted within 10 minutes after application of adhesive. Failure to adhere to timing will impair adhesive properties of window adhesive.
  • Align glass panel -1- centrally -2- in roof aperture -3- via centring pin -4-.

If there is no centring pin -2-, align glass panel -1- centrally in roof aperture -3- as shown in illustration -4-.

  • Push down glass panel -1- onto spacers.
Volkswagen ID.4. Removing and installing glass panel
  • Check gaps using setting gauge - 3371- . Observe ⇒ Rep. gr. 00 ; Gaps - roof for this.
  • Remove adhesive tape from windscreen seal sealing lip so that correct position of sealing lip is assured.

Continue installation in reverse order of removal.

Removing and installing frame with sun blind

Removing

  • Remove moulded headliner ⇒ General body repairs, interior; Rep. gr. 70 ; Roof trims; Removing and installing moulded headliner .
  • Disconnect electrical connector -2-.

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Unscrew nuts -3-, and remove slotted guide -1- from vehicle.
Volkswagen ID.4. Removing and installing frame with sun blind

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 60 ; Assembly overview - sun blind

Removing and installing roof system control unit J1355

Roof system control unit - J1355- is referred to hereafter as control unit.

Removing

  • Lower the moulded headliner, and place it on head restraints ⇒ General body repairs, interior; Rep. gr. 70 ; Roof trims; Removing and installing moulded headliner .

If the control unit is renewed, perform the test plan for renewal of the control unit:

  • Carry out function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Disconnect electrical connectors -3-.
  • Push tab -2- in direction of -arrow A-.
  • Swing control unit -1- downwards, and pull it in direction of -arrow B- out of retainers -4-.
Volkswagen ID.4. Removing and installing roof system control unit J1355

Installing

Install in reverse order of removal, observing the following:

  • Conclude function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Removing and installing sun blind

Removing

  • Open sun blind completely.

If the electrical system fails to operate, the sun blind can also be opened manually ⇒ Rep. gr. 60 ; Manual operation .

  • Remove moulded headliner ⇒ General body repairs, interior; Rep. gr. 70 ; Roof trims; Removing and installing moulded headliner .
  • Remove sun blind drive unit - VX455- ⇒ Rep. gr. 60 ; Removing and installing sun blind drive unit VX455 .
  • Remove frame with sun blind ⇒ Rep. gr. 60 ; Removing and installing frame with sun blind .
  • Push sun blind -2- by hand as far as possible towards rear in direction of -arrow A-.
  • Unscrew bolts -1-.
Volkswagen ID.4. Removing and installing sun blind
  • Pull sun blind -1- together with holders -2- in direction of -arrow A- out of sun blind frame -4- until connecting point between sun blind -1- and cables -3- becomes visible.
  • Detach cables -3- from slides -5- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing sun blind

Installing

Install in reverse order of removal, observing the following:

Important

  • Sun blind -1- always remains attached to holders -2-.
  • Attach cables -3- to slides -5- in sun blind -1-.
  • Push sun blind -1- with attached cables -3- in direction of -arrow A- in sun blind frame -4-.
Volkswagen ID.4. Removing and installing sun blind
  • Adapt ⇒ Rep. gr. 60 ; roof system control unit J1355 .

Tightening torques\

  • ⇒ Rep. gr. 60 ; Assembly overview - sun blind

Adapting roof system adjustment control unit J1355

Important

  • Ignition is switched on.
  • Press and hold "Close" button until adaption process is concluded (approx. 20 seconds).

The sun blind is completely closed.

Adaption can only be carried out using ⇒ Vehicle diagnostic tester.

  • Carry out function "Control unit, basic setting" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Removing and installing sun blind drive unit VX455

Sun blind drive unit - VX455- is referred to hereafter as motor.

Removing

  • Lower the moulded headliner, and place it on head restraints ⇒ General body repairs, interior; Rep. gr. 70 ; Roof trims; Removing and installing moulded headliner .
  • Disconnect electrical connector -4-.
  • Unscrew bolts -2- and pull off motor -1-.
  • Disconnect electrical connector -3- for motor -1-.
Volkswagen ID.4. Removing and installing sun blind drive unit VX455

Installing

Install in reverse order of removal, observing the following:

New motor

  • Install new spring plate.

All vehicles (continued)

  • Perform parallel alignment of sun blind before motor is installed.
  • Fit electrical connector -3- for motor -1-.

Important

  • Make sure that spring plate -2- is securely seated -arrows-.
  • Check spring plate -2-.
Volkswagen ID.4. Removing and installing sun blind drive unit VX455

New motor

  • Adapt ⇒ Rep. gr. 60 ; roof system control unit J1355 .

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 60 ; Assembly overview - sun blind

Removing and installing sun blind cables

Removing

  • Mark location of cables before removal to ease reinstallation.
  • Remove sun blind ⇒ Rep. gr. 60 ; Removing and installing sun blind .
  • Pull cables -1- in direction of -arrows- out of side sections of frame -2-.
Volkswagen ID.4. Removing and installing sun blind cables

Installing

Install in reverse order of removal.

Manual operation

Sun blind drive unit - VX455- is referred to hereafter as motor.

If the electrical system fails to operate, the sun blind can be manually operated with the aid of a commercially available hexagon key on the motor.

When doing so, considerable force must be exerted as the motor is not disengaged from the gearing.

  • Lower the moulded headliner, and place it on head restraints ⇒ General body repairs, interior; Rep. gr. 70 ; Roof trims; Removing and installing moulded headliner .
  • Guide commercially available hexagon key into connector -3- of motor -1-.
  • Turn bolt -2- to move sun blind.
Volkswagen ID.4. Manual operation

Minimum drying time for bonded glass panels

The minimum drying time is the time from bonding in until the vehicle is ready to be used.

The vehicle is safe to use only after the minimum drying time has elapsed.

Minimum drying time after installation of the glass panel is 24 hours.

Important

The following requirements during the minimum drying time must be complied with:

  • Vehicle must be standing on level surface.
  • No work must be performed on vehicle.
  • Room temperature must be between 20 ºC and 30 ºC.
  • Relative humidity must be between 30 % and 80 %.