Carrying out glass repair

In this manual: Carrying out glass repair
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~6min read

Removing

  • Clean the repair area with a dry cleaning cloth, while protecting the repair area from further soiling.
  • Remove loose fragments or surface contamination from the repair area with a carbide pin -A-.

Important

  • Do not increase the diameter.
Volkswagen ID.4. Carrying out glass repair
  • Wet the suction cup of mirror -A- with gel.
  • Position mirror -A- on the inside so that the repair area is clearly visible.
Volkswagen ID.4. Carrying out glass repair

correctness of information in this document. Copyright by Volkswagen AG.

- Remove loose fragments or surface contamination from the repair area with a carbide pin -A-.

Important - Do not increase the diameter.

- Wet the suction cup of mirror -A- with gel.

- Position mirror -A- on the inside so that the repair area is clearly visible.

If the impact point diameter is too small:

If the impact point diameter is too small:

Note

If the diameter of the impact point is too small, the resin cannot penetrate.

  • Drill out the impact point with a commercially available drill and a suitable drill bit at 2-second intervals.

Note

If drilling is done in short intervals, overheating of the drill bit can be avoided

Continued

  • View the repair area from different angles.

Important

  • If a dark area appears to be getting lighter, it is most likely moisture.

If moisture has entered the repair area:

  • Extract moisture.
  • Use vacuum procedure with tool carrier and injector for this.
  • Slowly heat inside of repair area with a commercially available hot air blower.

Note

Heat expands the repair area and moisture can escape.

  • Allow repair area to cool down

If moisture cannot be removed:

  • Abort glass repair.

Note

Moisture in the repair area can cause damage during and after the glass repair.

  • Inform the customer.
  • Renew window ⇒ General body repairs, exterior; Rep. gr. 64 ; Windscreen; Removing and installing windscreen .

Continued

  • Slowly heat inside of repair area with a commercially available hot air blower.

Note

Sudden temperature changes can cause further damage to the repair area.

  • Wet the suction cup of tool carrier -A- with gel.
  • Position tool carrier -A- centrally to the impact point and push lever towards rear.
Volkswagen ID.4. Carrying out glass repair
  • Open packaging.
  • Remove injector -B- and resin -A-.
  • Loosen piston of injector -B- by 4 to 5 mm.
  • Fill resin -A- into injector -B-.
  • Stow unused resin -A- in opaque packaging to avoid exposure to UV radiation.
Volkswagen ID.4. Carrying out glass repair
  • Screw injector -B- into tool carrier -A- until injector -B- rests lightly against the window.
  • Use mirror to centre seal of injector -B- on repair area, and turn until area between window and cylinder is tight.
Volkswagen ID.4. Carrying out glass repair
  • Screw in piston -B- until seal stretches by distance -a-.

Important

  • When screwing in piston -B-, counterhold cylinder.
  • Position of tool carrier -A- must be maintained.
  • Allow resin to penetrate for 5 min.

Note

When the damage is of type cow's eye, the resin penetrates quickly.

Note

In the event of closed fractures such as star-shaped fractures, the resin needs more time to penetrate. Only in the case of closed fractures may the piston be pressed lightly to favour the penetration of resin into the damaged area.

Volkswagen ID.4. Carrying out glass repair

Important

  • If too much pressure is applied to the repair area, the damage may be enlarged or resin flowers may form between the glass panes and the plastic film.

Vehicles without coloured or insulating plastic film on the inside of the window

If air venting is to be facilitated during the pressure cycle:

Important

  • Repair area must have cooled down before pressure is applied.

Note

Heat expands the repair area and makes the resin thinner.

  • Slowly heat inside of repair area with a commercially available hot air blower.

Note

Sudden temperature changes can cause further damage to the repair area.

All vehicles (continued)

  • Loosen piston -B- until distance -a- has been attained, and leave it in this position for 5 min

Dimension -a- = 10 mm

Important

  • When loosening piston -B-, counterhold cylinder.

Note

Air from inside the repair area is extracted. In the mirror, the air can be observed in the form of small black dots moving towards the injector and gradually disappearing

Volkswagen ID.4. Carrying out glass repair
  • Make sure that the repair area is filled with resin.
  • Use mirror to view repair area from all angles.

Important

  • The inspection must take place during the vacuum cycle, as air can compress during the pressure cycle and would not be visible as black dots.
  • Repeat procedures until the repair area is filled with resin.

Note

At least 2 pressure cycle and 2 vacuum cycles should be carried out.

  • To prevent the resin from retracting, perform pressure cycle as the last cycle.
  • Cut curing film -A- to size.

Important

  • Dimensions should be 4 cm to 5 cm.
  • Pull up lever of tool carrier, and slowly pull off the suction cup of tool carrier.
Volkswagen ID.4. Carrying out glass repair

Important

  • Air must have been extracted from repair area.
  • Place curing film -A- over repair area.

Important

  • Do not apply pressure to the repair area to prevent air from entering.
  • Remove excess resin outside the curing film -A-.
  • Lift curing film -A- and apply a drop -arrow- of finish resin -Bdirectly to repair area.
  • Place curing film -A- again.
Volkswagen ID.4. Carrying out glass repair
  • Moisten suction cups of UV lamp -1- with gel.
  • Position UV lamp -1- centrally relative to repair area.
  • Switch on UV lamp -1-.
  • Remove mirror.
  • Remove UV lamp and curing film.
  • Scrape off excess resin -arrow- with a commercially available blade -A- perpendicular to the glass pane.
Volkswagen ID.4. Carrying out glass repair

If there is not enough resin in impact point:

  • Apply another drop of finishing resin.
  • Place curing film.
  • Switch on UV lamp.
  • Allow resin to cure.
  • Scrape off excess resin with a commercially available blade perpendicular to the glass pane.

Continued

  • Clean repair area with lint-free cleaning cloth.
  • Clamp felt -B- in commercially available drill -A-.
  • Apply a small amount of polish to felt -B-.
  • Polish repair area briefly and press on felt only slightly.
Volkswagen ID.4. Carrying out glass repair
  • Screw piston into cylinder to stop.
  • Store injector in opaque packaging to avoid exposure to UV radiation.
  • Clean window from the outside and inside.

Note

The vehicle is operational right after the glass repair, without any waiting time.