Wheel bearing assembly, trailing arm

In this manual: Wheel bearing assembly, trailing arm
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~7min read
03060901201509066N·mlb·ft
Tightening torque found on this page
  • Assembly overview - wheel bearing
  • Removing and installing wheel bearing housing
  • Removing and installing wheel bearing unit
  • Raising wheel bearing assembly to unladen position

Assembly overview - wheel bearing

Overview shown for left side of vehicle as an example

Volkswagen ID.4. Assembly overview - wheel bearing
  1. Bolt
  • Depending on equipment/ version
  • ⇒ Electronic parts catalogue (ETKA)
  • Qty. 3 or 4
  • Renew after removing
  • 90 N·m +90º
  1. Wheel bearing housing
  • ⇒ Rep. gr. 42 ; Removing and installing wheel bearing housing
  1. Bonded rubber bush
  • For upper front suspension link
  1. Bonded rubber bush
  • For spring control arm
  1. Wheel bearing unit
  • ⇒ Rep. gr. 42 ; Removing and installing wheel bearing unit
  1. Bolt
  • Renew after removing
  • M16 × 1.5 × 70
  • 200 N·m +90º
  1. Bonded rubber bush
  • For lower front suspension link

Removing and installing wheel bearing housing

Special tools and workshop equipment required

  • engine and gearbox jack - VAS 6931-
  • gearbox support - T10337

Removing

Left parking brake motor - V282- and right parking brake motor - V283- are referred to hereafter as parking brake motor.

Rear right speed sensor - G44- and rear left speed sensor - G46- will be henceforth referred to as speed sensor.

Removal and installation are described for the left side of vehicle as an example.

  • Loosen threaded connection of drive shaft ⇒ Rep. gr. 42 ; Loosening and tightening threaded connections of drive shaft .
  • Disconnect electrical connector -2- on parking brake motor -1-.
Volkswagen ID.4. Removing and installing wheel bearing housing
  • Unscrew bolts -3- from wheel bearing housing -1-.
  • Move aside bracket -2- with electrical wires -4-.
Volkswagen ID.4. Removing and installing wheel bearing housing
  • Disconnect electrical connector -2- on speed sensor -3-.
Volkswagen ID.4. Removing and installing wheel bearing housing
  • Remove wheel bearing unit ⇒ Rep. gr. 42 ; Removing and installing wheel bearing unit
  • Unscrew bolts -arrows-.
  • Detach brake carrier -1- from wheel bearing housing -2 - with brake hose still connected.
  • Tie up brake carrier -1- to one side.
Volkswagen ID.4. Removing and installing wheel bearing housing
  • Fit gearbox support - T10337- -A- onto engine and gearbox jack - VAS 6931- -B-.
  • Position gearbox support - T10337- -A- on spring control arm -1-.

CAUTION

Risk of accident when the vehicle is lowered or raised while support and lifting equipment is located underneath.

  • Never raise or lower the vehicle while support and lifting equipment is located underneath.
  • Do not leave support and lifting equipment longer than necessary under the vehicle.
Volkswagen ID.4. Removing and installing wheel bearing housing
  • Position engine and gearbox jack - VAS 6931- -A- under spring control arm -1-, and push it upwards to take up weight.
  • Unscrew nuts -3- and -7-.
  • Pull out bolts -2- and -8-.
  • Unscrew bolts -4- and -9-.
  • Unscrew nut -6-.
  • Hold wheel bearing housing -1- in position.
  • Lower engine and gearbox jack - VAS 6931- .
  • Hold wheel bearing housing -1-, and pull out bolt -5-.
  • Remove wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing wheel bearing housing

Installing

Install in reverse order of removal, observing the following:

  • ⇒ Rep. gr. 42 ; Raise wheel bearing in unladen position .
  • Perform wheel alignment ⇒ Rep. gr. 44 ; Necessity of wheel alignment .

Tightening torques

  • ⇒ Rep. gr. 42 ; Assembly overview - wheel bearing
  • ⇒ Rep. gr. 42 ; Assembly overview - shock absorber
  • ⇒ Rep. gr. 42 ; Assembly overview - track rod
  • ⇒ Rep. gr. 42 ; Assembly overview - suspension link
  • ⇒ Rep. gr. 42 ; Assembly overview - spring control arm
  • ⇒ Rep. gr. 42 ; Loosening and tightening threaded connections of drive shaft

Removing and installing wheel bearing unit

Removing

Removal and installation are described for the left side of vehicle as an example.

  • Loosen threaded connection of drive shaft ⇒ Rep. gr. 42 ; Loosening and tightening threaded connections of drive shaft .
  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • Press drive shaft out of wheel bearing unit ⇒ Rep. gr. 42 ; Removing and installing drive shaft .
  • Remove brake drum ⇒ Brake system; Rep. gr. 46 ; Rear brake; Assembly overview - rear brake, drum brake .
  • Unclip electrical wire -4-.
  • Unscrew bolts -2-.
  • Press outer joint of drive shaft inwards, and remove bolts -2-.
  • Pull wheel bearing unit -3- towards outside off wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing wheel bearing unit

NOTICE

Contamination and damage to seals from incorrect handling of wheel bearing unit.

  • Only pick up, place down and store wheel bearing unit as shown in illustration.
  • Place wheel bearing unit -2- onto wheel hub -1-.

Important

  • Grab wheel bearing unit only on outside.
  • When picking up wheel bearing unit, do not grasp on toothing on the inside.
Volkswagen ID.4. Removing and installing wheel bearing unit

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 42 ; Assembly overview - wheel bearing
  • ⇒ Rep. gr. 42 ; Assembly overview - drive shaft

Raising wheel bearing assembly to unladen position

Special tools and workshop equipment required

  • engine and gearbox jack - VAS 6931-
  • gearbox support - T10337-

Removal and installation are described for the left side of vehicle as an example.

NOTICE

Bolts and nuts on running gear components with bushes not tightened with the respective component in unladen position: Suspension link bushes wear out prematurely or cause noises.

  • Before tightening axle components with bushes, the respective component must be brought to a position equivalent to the position when the vehicle is moving (unladen position).
  • ⇒ Rep. gr. 42 ; Secure vehicle to support arms of lifting platform .
  • Remove stone deflector for spring control arm ⇒ Rep.

    gr. 42 ; Removing and installing stone deflector for spring control arm .

  • Position engine and gearbox jack - VAS 6931- -B- with gearbox support - T10337- -A- at anti-roll bar -1-.

Important

  • Mounting of gearbox support - T10337- -A- may only contact anti-roll bar -1-.
Volkswagen ID.4. Raising wheel bearing assembly to unladen position

CAUTION

Risk of accident when the vehicle is lowered or raised while support and lifting equipment is located underneath.

  • Never raise or lower the vehicle while support and lifting equipment is located underneath.
  • Do not leave support and lifting equipment longer than necessary under the vehicle.
  • Push anti-roll bar -1- upwards.
  • Unscrew nut -6- on coupling rod -1-. Counterhold on multipoint socket head on coupling rod -1- when doing this.
  • Pull coupling rod -1- out of anti-roll bar -5-.
Volkswagen ID.4. Raising wheel bearing assembly to unladen position
  • Fit gearbox support - T10337- -A- onto engine and gearbox jack - VAS 6931- -B- at spring control arm -1-.
Volkswagen ID.4. Raising wheel bearing assembly to unladen position

CAUTION

Risk of accident when the vehicle is lowered or raised while support and lifting equipment is located underneath.

  • Never raise or lower the vehicle while support and lifting equipment is located underneath.
  • Do not leave support and lifting equipment longer than necessary under the vehicle.
  • Push spring control arm upwards using engine and gearbox jack - VAS 6931- .
  • Raise wheel bearing housing -1- with engine and gearbox jack - VAS 6931- -A- until dimension -a- is obtained ⇒ Rep.

    gr. 00 ; Test and adjustment figures .

Important

  • The respective bolts and nuts may only be tightened if the dimension between the centre of wheel hub and lower edge of wheel housing specified in the table has been obtained.
  • Tighten bolts and nuts.
  • Lower engine and gearbox jack - VAS 6931- .
Volkswagen ID.4. Raising wheel bearing assembly to unladen position

Tightening torques

  • ⇒ Rep. gr. 42 ; Assembly overview - spring control arm
  • ⇒ Rep. gr. 42 ; Assembly overview - shock absorber
  • ⇒ Rep. gr. 42 ; Assembly overview - suspension link
  • ⇒ Rep. gr. 42 ; Assembly overview - track rod
  • ⇒ Rep. gr. 42 ; Assembly overview - anti-roll bar