High-voltage battery unit, edge of upper part of battery housing without wax

In this manual: High-voltage battery unit, edge of upper part of battery housing without wax
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
2steps
~12min
1/5difficulty
050100150200250150111N·mlb·ft
Tightening torque found on this page
Done 0 of 2
  • Assembly overview - high-voltage battery, installed, 48, 55, 62 kWh
  • Assembly overview - high-voltage battery, installed, 82 kWh
  • Inspecting and classifying high-voltage battery 1 AX2
  • Diagnosis of high-voltage battery 1 [AX2]
  • Removing and installing high-voltage battery 1 [AX2], 48, 55, 62 kWh
  • Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Raising high-voltage battery 1 [AX2]
  • Opening high-voltage battery 1 AX2
  • Sealing high-voltage battery 1 [AX2], 48, 55, 62 kWh
  • Sealing high-voltage battery 1 [AX2], 82 kWh
  • Voltage and insulation measurement, 48, 55, 62 kWh
  • Voltage and insulation measurement, 82 kWh
  • Opening electrical circuit, 48, 55 kWh
  • Opening electrical circuit, 62 kWh
  • Opening electrical circuit, 82 kWh
  • Removing and installing battery regulation control unit J840
  • Charging and discharging battery modules
  • Checking whether upper part of battery housing can be reused
  • Renewing lower part of battery housing
  • Renewing high-voltage battery 1 [AX2]

Assembly overview - high-voltage battery, installed, 48, 55, 62 kWh

Assembly overview - high-voltage battery, installed

Volkswagen ID.4. Assembly overview - high-voltage battery, installed
  1. High-voltage battery 1 - AX2-
  • ⇒ Rep. gr. 93 ; Removing and installing high-voltage battery 1 [AX2]
  1. Bolt
  • Qty. 16
  • Renew after removing
  • Specified torque and tightening sequence
  1. Skid plate for high-voltage battery
  • ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing high-voltage battery skid plate
  1. Reinforcement for highvoltage battery body aperture
  2. Centre underbody cladding
  • ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing centre underbody cladding
  1. Bolt
  • Qty. 14
  • Renew after removing
  • Specified torque and tightening sequence
  1. Bolt
  • Qty. 4
  • Renew after removing
  • Specified torque and tightening sequence
  1. Banjo bolt
  • Qty. 4
  • Renew after removing
  • 150 N·m

High-voltage battery - specified torque and tightening sequence

Volkswagen ID.4. Assembly overview - high-voltage battery, installed

Assembly overview - high-voltage battery, installed, 82 kWh

Assembly overview - high-voltage battery, installed

Volkswagen ID.4. Assembly overview - high-voltage battery, installed
  1. High-voltage battery 1 - AX2-
  • ⇒ Rep. gr. 93 ; Removing and installing high-voltage battery 1 [AX2]
  1. Bolt
  • Qty. 24
  • Renew after removing
  • Specified torque and tightening sequence
  1. Skid plate for high-voltage battery
  • ⇒ General body repairs, exterior; Rep.gr. 66 ; Underbody cladding; Removing and installing high-voltage battery skid plate
  1. Bolt
  • Qty. 4
  • Renew after removing
  • Specified torque and tightening sequence
  1. Banjo bolt
  • Qty. 4
  • Renew after removing
  • 150 N·m
Volkswagen ID.4. Assembly overview - high-voltage battery, installed

Inspecting and classifying high-voltage battery 1 AX2

Special tools and workshop equipment required

  • diagnosis box - VAS 5581A-
  • diagnostic cable - VAS 5581A/11-
  • vehicle diagnostic tester

CAUTION

The high-voltage battery can become extremely hot. This can cause injuries.

Take care not to burn your hands.

  • Put on protective gloves.

Note

Inform the high-voltage expert if any problems arise or entries in the event memory appear.

Visual inspection of high-voltage battery 1 [AX2]

Inspect the high-voltage battery 1 - AX2- for the following:

  • Cracks in upper or lower parts of battery housing
  • Deformations in upper or lower parts of battery housing
  • Colour changes due to temperature impact and tarnishing of battery housing
  • Escaping electrolyte
  • Damage to high-voltage contacts
  • Legible information and warning stickers properly in place
  • Fitted potential equalisation line
  • Corrosion damage
  • If abnormalities are detected during the visual inspection, a classification of the high-voltage battery 1 - AX2- must be carries out.

Preparatory work on removed high-voltage battery:

  • Connect diagnosis box - VAS 5581A- via diagnostic cable - VAS 5581A/11- to vehicle diagnostic tester .

Important

  • Before commencing the diagnosis, Gateway (GW) operating mode must be selected on the diagnosis box - VAS 5581A- .
  • Connect diagnostic cable - VAS 5581A/11- to 12V-connector -1- of high-voltage battery 1 - AX2- .
  • Connect black earth terminal of diagnostic cable - VAS 5581A/11- to earth of battery housing -arrow-.
Volkswagen ID.4. Inspecting and classifying high-voltage battery 1 AX2

Classification of high-voltage battery:

  • Carry out classification of high-voltage battery using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Diagnosis of high-voltage battery 1 [AX2]

Special tools and workshop equipment required

  • diagnosis box - VAS 5581A-
  • diagnostic cable - VAS 5581A/11-
  • vehicle diagnostic tester

High-voltage battery installed

Important

  • The high-voltage battery 1 remains installed in the vehicle during the diagnosis.
  • Carry out diagnosis of high-voltage battery using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnosis .

High-voltage battery removed

  • Connect diagnosis box - VAS 5581A- via diagnostic cable - VAS 5581A/11- to vehicle diagnostic tester .

Important

  • Before commencing the diagnosis, Gateway (GW) operating mode must be selected on the diagnosis box - VAS 5581A- .
  • Connect diagnostic cable - VAS 5581A/11- to 12V-connector -1- of high-voltage battery 1 - AX2- .
  • Connect black earth terminal of diagnostic cable - VAS 5581A/11- to earth of battery housing -arrow-.
  • Carry out diagnosis of high-voltage battery using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnosis .
Volkswagen ID.4. Diagnosis of high-voltage battery 1 [AX2]

For further measures on high-voltage battery:

  • Disconnect diagnosis box - VAS 5581A- .

Checking high-voltage battery for leaks

Special tools and workshop equipment required

  • pressure and vacuum pump - VAS 671 005-
  • sealing plugs - T10607-

Note

Searching for leaks from the high-voltage battery 1 - AX2- is only required if the leak test under pressure failed.

Note

Leaks are indicated by bubbles.

Note

Leaks can potentially be traced to the banjo bolts on the underside of high-voltage battery 1 - AX2- .

  • Seal connections of high-voltage battery 1 - AX2- using sealing plugs - T10607- .
  • Build up pressure using pressure and vacuum pump - VAS 671 005- .
  • Using commercially available leak detection spray
  • Spray contact surfaces of upper part of battery housing and lower part of battery housing.
  • Spray banjo bolts on underside

Leakage test of high-voltage battery 1 [AX2]

Special tools and workshop equipment required

  • Distributor - VAS 691 005/1-
  • Pressure and vacuum pump - VAS 671 005-
  • Pressure sensor - V.A.G 1397B-
  • Pressure sensor - VAS 611 013-
  • Sealing plug - T10607-
  • Test connector set - VAS 6911/3B

Important

  • A leak test must always be carried out with vacuum before removing and after installing the high-voltage battery 1 - AX2- .
  • High-voltage battery 1 - AX2- is acclimatised.
  • The leakage test and acclimatisation must be carried out at a steady ambient temperature.
  • Check that gasket -arrows- is correctly seated.
  • Check connector strip for moisture. Carefully wipe with lintfree cleaning cloth.
Volkswagen ID.4. Leakage test of high-voltage battery 1 [AX2]
  • Carry out "Leak test" function with ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Removing and installing high-voltage battery 1 [AX2], 48, 55, 62 kWh

Removing and installing high-voltage battery 1 [AX2]

Special tools and workshop equipment required

  • drip tray - VAS 6208-
  • engine bung set - VAS 6122-
  • hose clamps, up to 25 mm - 3094-
  • insulating mat - VAS 6762/44-
  • scissor-type assembly platform - VAS 6131BID

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.

CAUTION

The high-voltage battery can become extremely hot. This can cause injuries.

Take care not to burn your hands.

  • Put on protective gloves.

NOTICE

Potential damage to vehicle

  • Make sure that nobody is inside the vehicle after the highvoltage battery has been removed.

The high-voltage battery 1 - AX2- will subsequently be referred to as "high-voltage battery".

Removing

  • ⇒ Rep. gr. 93 ; Visual inspection of high-voltage battery 1 [AX2] .

NOTICE

Potential damage to vehicle from slipping.

  • The dimensions of the vehicle support plates and their spindles must be sufficient to ensure that the load that is imparted centrally between the outer edge and centre of the vehicle support plates can be supported. If the dimensions are not sufficient, different vehicle support plates must be used that meet this requirement.

Note

Not every lifting platform is suitable for the removal of the highvoltage battery. Ensure that there is sufficient clearance. When lifting, ensure that there is sufficient clearance -a- around the high-voltage battery so that it can be placed on the scissor-type assembly platform - VAS 6131B- .

  • Swivel lifting platform arm with vehicle support plate -1- up to frame of high-voltage battery -2-. Then swivel back lifting platform arm with vehicle support plate -1- far enough -ato allow for lowering high-voltage battery -2- in the following step.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Remove front underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing front underbody cladding .
  • Detach front right wheel housing liners in area of threaded connection of high-voltage battery ⇒ General body repairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing and installing front wheel housing liner .
  • Remove side underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing side underbody cladding .
  • Remove centre underbody cladding.
  • Remove rear centre underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear centre underbody cladding .
  • Remove rear underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear underbody cladding .
  • Loosen and unscrew bolts -2- by hand.
  • Pull out reinforcement for high-voltage battery body aperture -1-.
  • ⇒ Rep. gr. 93 ; De-energising high-voltage system
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Unscrew nut for potential equalisation line -1-. Counterhold on centre hex stud, when doing this.
  • Disconnect electrical connector of high-voltage battery -2-.
  • Disconnect electrical connector for auxiliary consumers -5-
  • Rep. gr. 93 ; Disconnecting high-voltage connectors .
  • Remove pressure relief valve -3-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Perform ⇒ Rep. gr. 93 ; leakage test of high-voltage battery 1 [AX2] .
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Disconnect high-voltage system connection -4- ⇒ Rep. gr. 93 ; Disconnecting high-voltage connectors .
  • Disconnect DC charging connection -6-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Check that gasket -arrows- is correctly seated.
  • Check connector strip for moisture, and carefully wipe it dry with a lint-free cloth.
  • Fit cap -2- on connector strip -1-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Unscrew bolts -1- from coolant pump for high-voltage battery - V590- .
  • Open clip -2-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Pull coolant pump in direction of -arrow-, and disconnect electrical connector -1-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Loosen bolts -2- and -3- by hand.
  • Unscrew bolts -2- and -3- from high-voltage battery -1-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]

NOTICE

Risk of damage to the high-voltage battery.

  • The high-voltage battery must lie flat against the scissortype assembly platform - VAS 6131B- . Remove any kind of soiling.

Important

  • Scissor-type assembly platform and front side of high-voltage battery must be flush -arrow-.
  • Lay insulating mat - VAS 6762/44- -2- centrally on scissortype assembly platform - VAS 6131B- -3-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Align scissor-type assembly platform - VAS 6131B- -1- so that it is flush with front side of high-voltage battery; highvoltage battery must lie flat against the platform.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]

CAUTION

Risk of injury from moving parts.

Body parts could suffer contusions.

  • Never reach or step into the hazard zone.

NOTICE

Risk of damage to components caused by moving scissortype assembly platform.

  • Ensure sufficient clearance to body.
  • Ensure sufficient clearance to electrical wiring and electrical connectors.
  • Raise scissor-type assembly platform - VAS 6131B- -3- far enough to take up weight of high-voltage battery -1-.
  • Loosen and unscrew bolts -2- from high-voltage battery -1- by hand.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Carefully lower high-voltage battery until coolant connections become accessible.
  • Place drip tray - VAS 6208- under coolant connections.
  • Clamp off coolant hoses -1- and -2- using hose clamps, up to 25 mm - 3094- -A-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Pull out retaining clips for coolant connections -1- in direction of -arrow-, and pull coolant hoses off high-voltage battery.
  • Seal coolant connections with plugs from engine bung set - VAS 6122- .
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Carefully lower high-voltage battery.
  • Secure media duct -1- with screws -2- ⇒ Electronic parts catalogue (ETKA) .
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]

Installing

Install in reverse order of removal, observing the following:

New high-voltage battery

  • Perform procedure for renewal of high-voltage battery ⇒ Rep. gr. 93 ; Renewing high-voltage battery 1 [AX2] .

All vehicles (continued)

Removed high-voltage battery

  • Remove separating film -2- from lower part of battery housing -1-.
  • Clean area of separating film -2- with cleaning solution ⇒ Electronic parts catalogue (ETKA) .
  • Renew separating film -2-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]

All vehicles (continued)

CAUTION

Risk of injury from moving parts.

Body parts could suffer contusions.

  • Never reach or step into the hazard zone.

NOTICE

Risk of damage to components caused by moving scissortype assembly platform.

  • Ensure sufficient clearance to body.
  • Ensure sufficient clearance to electrical wiring and electrical connectors.
  • Align high-voltage battery on scissor-type assembly platform - VAS 6131B- under vehicle.
  • Raise high-voltage battery on scissor-type assembly platform - VAS 6131B- to 5 cm before end position.
  • Connect coolant hoses.
  • Raise high-voltage battery on scissor-type assembly platform - VAS 6131B- to end position
  • Tighten bolts -2- to specified torque according to specified tightening sequence.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Tighten bolts -2- and -3- to specified torque according to specified tightening sequence.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Connect high-voltage system connection -4-.
  • Connect DC charging connection -6-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Perform ⇒ Rep. gr. 93 ; leakage test of high-voltage battery 1 [AX2] .
  • Connect electrical connector of high-voltage battery -2-.
  • Connect electrical connector for auxiliary consumers -5-.
  • Install pressure relief valve -3-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Install body aperture reinforcement for high-voltage battery -1-. To do this, tighten bolts -2- in specified tightening sequence to specified torque.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2]
  • Tighten nut for potential equalisation line to specified torque.

    Counterhold on centre hex stud when doing this.

  • ⇒ Rep. gr. 19 ; Cooling system/coolant; Filling cooling system

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; Re-energise high-voltage system .

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - high-voltage battery (installed)
  • ⇒ Rep. gr. 93 ; Overview of fitting locations - potential equalisation lines

Removing and installing high-voltage battery 1 [AX2], 82 kWh

Removing and installing high-voltage battery 1 [AX2]

Special tools and workshop equipment required

  • drip tray - VAS 6208-
  • engine bung set - VAS 6122-
  • hose clamps, up to 25 mm - 3094-
  • insulating mat - VAS 6762/44-
  • scissor-type assembly platform - VAS 6131BDANGER

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.

CAUTION

The high-voltage battery can become extremely hot. This can cause injuries.

Take care not to burn your hands.

  • Put on protective gloves.

NOTICE

Potential damage to vehicle

  • Make sure that nobody is inside the vehicle after the highvoltage battery has been removed.

The high-voltage battery 1 - AX2- will subsequently be referred to as "high-voltage battery".

Removing

  • ⇒ Rep. gr. 93 ; Visual inspection of high-voltage battery 1 [AX2] .

NOTICE

Potential damage to vehicle from slipping.

  • The dimensions of the vehicle support plates and their spindles must be sufficient to ensure that the load that is imparted centrally between the outer edge and centre of the vehicle support plates can be supported. If the dimensions are not sufficient, different vehicle support plates must be used that meet this requirement.

Note

Not every lifting platform is suitable for the removal of the highvoltage battery. Ensure that there is sufficient clearance. When lifting, ensure that there is sufficient clearance -a- around the high-voltage battery so that the high-voltage battery can be placed on the scissor-type assembly platform - VAS 6131B-

  • Swivel lifting platform arm with vehicle support plate -1- up to frame of high-voltage battery -2-. Then swivel back lifting platform arm with vehicle support plate -1- far enough -ato allow for lowering high-voltage battery -2- in the following step.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Remove front underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing front underbody cladding .
  • Detach front right wheel housing liners in area of threaded connection of high-voltage battery ⇒ General body repairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing and installing front wheel housing liner .
  • Remove side underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing side underbody cladding .
  • Remove rear centre underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear centre underbody cladding .
  • Remove rear underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear underbody cladding .
  • ⇒ Rep. gr. 93 ; De-energise high-voltage system

NOTICE

Potential leakage of the high-voltage battery due to impurities in the seal area of the electrical plug connectors.

  • Sealing surfaces on the connector strip must be free of impurities.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Remove coarse soiling in area of electrical connectors.
  • Unscrew nut for potential equalisation line -1-. Counterhold on centre hex stud, when doing this.
  • Disconnect electrical connector of high-voltage battery -2-.
  • Disconnect electrical connector for auxiliary consumers -5- ⇒ Rep. gr. 93 ; Disconnecting high-voltage connectors .
  • Remove pressure relief valve -3-.
  • Perform ⇒ Rep. gr. 93 ; leakage test of high-voltage battery 1 [AX2] .

Note

For better disconnection of the high-voltage system connector, the guide of the high-voltage system connection cable must be removed.

  • Unclip locking devices -arrow-.
  • Separate lower part of cable duct -1- from cable duct cover -2-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Disconnect high-voltage system connection -4- ⇒ Rep.

    gr. 93 ; Disconnecting high-voltage connectors .

  • Disconnect DC charging connection -6-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Check that gasket -arrows- is correctly seated.
  • Carefully absorb moisture from connector strip using lint-free cleaning cloth.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh

NOTICE

Potential leakage of the high-voltage battery due to impurities in the seal area of the electrical plug connectors.

  • Sealing surfaces on the connector strip must be free of impurities.
  • Remove soiling from connector strip using lint-free cleaning cloth and cleaning solution ⇒ Electronic parts catalogue (ETKA) .
  • Fit cap -2- on connector strip -1-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Unscrew bolts -1- from coolant pump for high-voltage battery - V590- .
  • Open clip -2
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Pull coolant pump in direction of -arrow-, and disconnect electrical connector -1-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Loosen bolts -2- and -3- by hand.
  • Unscrew bolts -2- and -3- from high-voltage battery -1-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh

NOTICE

Risk of damage to the high-voltage battery.

  • The high-voltage battery must lie flat against the scissortype assembly platform - VAS 6131B- . Remove any kind of soiling.
  • Note position of the spirit level -3- on the scissor-type assembly platform - VAS 6131B- .
  • Lay insulating mat - VAS 6762/44- centrally on scissor-type assembly platform - VAS 6131B- -1-.
  • Place scissor-type assembly platform - VAS 6131B- -1- underneath, and align it so that high-voltage battery -2- can lie flat against it.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh

CAUTION

Risk of injury from moving parts.

Body parts could suffer contusions.

  • Never reach or step into the hazard zone.

NOTICE

Risk of damage to components caused by moving scissortype assembly platform.

  • Ensure sufficient clearance to body.
  • Ensure sufficient clearance to electrical wiring and electrical connectors.
  • Raise scissor-type assembly platform - VAS 6131B- -1- far enough to take weight off high-voltage battery.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Loosen and unscrew bolts -2- from high-voltage battery -1- by hand.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Carefully lower high-voltage battery until coolant connections become accessible.
  • Place drip tray - VAS 6208- under coolant connections.
  • Clamp off coolant hoses -1- and -2- using hose clamps, up to 25 mm - 3094- -A-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Pull out retaining clips for coolant connections -1- in direction of -arrow-, and pull coolant hoses off high-voltage battery.
  • Seal coolant connections with plugs from engine bung set - VAS 6122- .
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Carefully lower high-voltage battery.
  • Secure media duct -1- with screws -2- ⇒ Electronic parts catalogue (ETKA) .
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh

Installing

Install in reverse order of removal, observing the following:

New high-voltage battery:

  • Perform procedure for renewal of high-voltage battery ⇒ Rep. gr. 93 ; Renewing high-voltage battery 1 [AX2] .

All vehicles (continued)

Removed high-voltage battery

  • Remove separating film -2- from lower part of battery housing -1-.
  • Clean area of separating film -2- with cleaning solution ⇒ Electronic parts catalogue (ETKA) .
  • Renew separating film -2-
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh

All vehicles (continued)

CAUTION

Risk of injury from moving parts.

Body parts could suffer contusions.

  • Never reach or step into the hazard zone.

NOTICE

Risk of damage to components caused by moving scissortype assembly platform.

  • Ensure sufficient clearance to body.
  • Ensure sufficient clearance to electrical wiring and electrical connectors.
  • Align high-voltage battery on scissor-type assembly platform - VAS 6131B- under vehicle.
  • Raise high-voltage battery on scissor-type assembly platform - VAS 6131B- to 5 cm before end position.
  • Connect coolant hoses.
  • Raise high-voltage battery on scissor-type assembly platform - VAS 6131B- to end position.
  • Tighten bolts -2- to specified torque according to specified tightening sequence.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Tighten bolts -2- and -3- to specified torque according to specified tightening sequence.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Connect high-voltage system connection -4-.
  • Connect DC charging connection -6-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Perform ⇒ Rep. gr. 93 ; leakage test of high-voltage battery 1 [AX2] .
  • Connect electrical connector of high-voltage battery -2-.
  • Connect electrical connector for auxiliary consumers -5-.
  • Install pressure relief valve -3-.
Volkswagen ID.4. Removing and installing high-voltage battery 1 [AX2], 82 kWh
  • Tighten nut for potential equalisation line to specified torque, counterholding at centre hex stud while doing so.
  • ⇒ Rep. gr. 19 ; Cooling system/coolant; Filling cooling system

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.

⇒ Rep. gr. 93 ; Re-energise high-voltage system .

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - high-voltage battery (installed)
  • ⇒ Rep. gr. 93 ; Overview of fitting locations - potential equalisation lines

Raising high-voltage battery 1 [AX2]

Special tools and workshop equipment required

  • extension for lifting arm/workshop hoist - VAS 6101-
  • lifting aid - T10616-
  • master link - VAS 501 013-
  • retaining strap - T40155A-
  • shackle - VAS 691 009A-
  • workshop hoist - VAS 6100-

Preparing for lifting

The high-voltage battery 1 - AX2- will subsequently be referred to as "high-voltage battery".

Preparing for lifting, 55 and 62 kWh

  • Use mounting points -2-.
Volkswagen ID.4. Raising high-voltage battery 1 [AX2]

All vehicles (continued)

Preparing for lifting, 82 kWh

  • Use mounting points -2-.
Volkswagen ID.4. Raising high-voltage battery 1 [AX2]

All vehicles (continued)

Lifting

  • Align extension for lifting arm/workshop hoist - VAS 6101- -A- at marking -arrow- and secure to workshop hoist - VAS 6100- -B-.
  • Position workshop hoist - VAS 6100- -A- and workshop hoist - VAS 6100- -B- centrally above high-voltage battery -1-.
  • Secure retaining strap - T40155A- -F- with shackle - VAS 691 009A- -H- to master link - VAS 501 013- -G-.
  • Tighten lifting aid - T10616- -E- at mounting points of highvoltage battery -1- to specified torque.
  • Attach mounting bracket - T10616- -E- with shackle - VAS 691 009A- -D- to retaining strap - T40155A- -F-.

CAUTION

Risk of injury from moving parts.

Body parts could suffer contusions.

  • Never reach or step into the hazard zone.
  • Lift high-voltage battery -1-.
Volkswagen ID.4. Raising high-voltage battery 1 [AX2]

Opening high-voltage battery 1 AX2

Special tools and workshop equipment required

  • nylon pipe brush - VAS 294 029-

Opening

  • Remove high-voltage battery 1 - AX2- ⇒ Rep. gr. 93 ; Removing and installing high-voltage battery 1 AX2 .
  • Unscrew connecting element -4-.
  • Clean threaded holes -4- using nylon pipe brush - VAS 294 029- and commercially available vacuum cleaner with plastic nozzle.
  • Remove bolts -3-.
  • Remove bolts -2-.
Volkswagen ID.4. Opening high-voltage battery 1 AX2

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Put on protective equipment ⇒ Electronic parts catalogue (ETKA) before performing the following work steps:

  • Clothing approved for working with electric arcs (minimum protection class 2, at least 318 kJ)
  • Helmet with visor approved for working with electric arcs (minimum protection class 2, at least 318 kJ)
  • Gloves approved for working with electric arcs with nitrile glove liners (minimum protection class 2, at least 318 kJ), minimum insulating effect up to 500 V
  • Safety shoes with ESD protection
  • Detach upper part of battery housing -1-.
  • ⇒ Rep. gr. 93 ; Voltage and insulation measurement .
  • ⇒ Rep. gr. 93 ; Check whether upper part of battery housing can be reused .

If further work is being performed on high-voltage battery:

  • Interrupt electrical circuit ⇒ Rep. gr. 93 ; Interrupting electrical circuit .
  • Cover areas of high-voltage battery 1 - AX2- that are not being worked on.

Sealing high-voltage battery 1 [AX2], 48, 55, 62 kWh

Closing high-voltage battery 1 AX2

Special tools and workshop equipment required

  • Hand-cartridge gun - V.A.G 1628-
  • High-voltage tool set - VAS 6762-
  • High-voltage tool set - VAS 6883A-
  • suction lifter - V.A.G 1344-

Installing

  • Close electrical circuit ⇒ Rep. gr. 93 ; Opening electrical circuit
  • ⇒ Rep. gr. 93 ; Diagnosis of high-voltage battery 1 [AX2] .

If high-voltage battery 1 - AX2- is opened, the flow-drill screws must be checked and renewed according to the following table.

  • Flow-drill screws

Production version:

Inner thread on lower part of battery housing OK

Repair bolt, stage 1:

Inner thread on lower part of battery housing OK Torque specified for production bolt has not been attained.

Repair bolt, stage 2:

Inner thread on lower part of battery housing not OK (thread stripped)

Production version:

After opening highvoltage battery 1 - AX2- , the original bolts must be used ⇒ Electronic parts catalogue (ETKA) .

Repair bolt, stage 1:

Replace production bolt and use max.

quantity of 14 ⇒ Electronic parts catalogue (ETKA)

Repair bolt, stage 2:

Use oversized bolt (new thread will be cut) ⇒ Electronic parts catalogue (ETKA)

Continued

NOTICE

Leakage of high-voltage battery 1 - AX2- possible.

  • Flange of lower part of battery housing must be free of grease, sealant residue and contamination.
  • Use a commercially available vacuum cleaner with plastic nozzle to clean lower part of battery housing; remove sealing material and soiling.
  • Clean flange of lower part of battery housing using lint-free cleaning cloth and cleaning solution ⇒ Electronic parts catalogue (ETKA) .
  • Secure suction lifter - V.A.G 1344- -2- at top of upper part of battery housing -1-.
  • Turn upper part of battery housing -1- in direction of -arrow-.
  • Place on suitable surface.
Volkswagen ID.4. Sealing high-voltage battery 1 [AX2], 48, 55, 62 kWh

New upper part of battery housing

  • Clean flange of upper part of battery housing using lint-free cleaning cloth and cleaning solution ⇒ Electronic parts catalogue (ETKA) .

All vehicles (continued)

  • Apply sealant -3- ⇒ Electronic parts catalogue (ETKA) to upper part of battery housing -1- all around and parallel to gasket -2-.
  • Place upper part of battery housing -1- evenly on lower part of battery housing.
Volkswagen ID.4. Sealing high-voltage battery 1 [AX2], 48, 55, 62 kWh

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - high-voltage battery (removed)
  • Seal bolts -1- through -18- with wax ⇒ Electronic parts catalogue (ETKA) .
Volkswagen ID.4. Sealing high-voltage battery 1 [AX2], 48, 55, 62 kWh

Sealing high-voltage battery 1 [AX2], 82 kWh

Closing high-voltage battery 1 AX2

Special tools and workshop equipment required

  • Hand-cartridge gun - V.A.G 1628-
  • High-voltage tool set - VAS 6762-
  • High-voltage tool set - VAS 6883A-
  • suction lifter - V.A.G 1344-

Installing

  • Close electrical circuit ⇒ Rep. gr. 93 ; Opening electrical circuit .
  • ⇒ Rep. gr. 93 ; Diagnosis of high-voltage battery 1 [AX2] .

If high-voltage battery 1 - AX2- is opened, the flow-drill screws must be checked and renewed according to the following table:

  • Flow-drill screws

Continued

NOTICE

Leakage of high-voltage battery 1 - AX2- possible.

  • Flange of lower part of battery housing must be free of grease, sealant residue and contamination.
  • Use a commercially available vacuum cleaner with plastic nozzle to clean lower part of battery housing; remove sealing material and soiling.
  • Clean flange of lower part of battery housing using lint-free cleaning cloth and cleaning solution ⇒ Electronic parts catalogue (ETKA) .
  • Secure suction lifter - V.A.G 1344- -2- at top of upper part of battery housing -1-.
  • Turn upper part of battery housing -1- in direction of -arrow-.
  • Place on suitable surface.
Volkswagen ID.4. Sealing high-voltage battery 1 [AX2], 82 kWh

New upper part of battery housing

  • Clean flange of upper part of battery housing using lint-free cleaning cloth and cleaning solution ⇒ Electronic parts catalogue (ETKA) .

All vehicles (continued)

  • Clean flange of upper part of battery housing -1- using lintfree cleaning cloth and cleaning solution ⇒ Electronic parts catalogue (ETKA) .
  • Apply sealant -3- ⇒ Electronic parts catalogue (ETKA) to upper part of battery housing -1- all around and parallel to gasket -2-.
  • Place upper part of battery housing -1- evenly on lower part of battery housing.
Volkswagen ID.4. Sealing high-voltage battery 1 [AX2], 82 kWh

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - high-voltage battery (removed)
  • Seal bolts -1- through -26- with wax ⇒ Electronic parts catalogue (ETKA) .
Volkswagen ID.4. Sealing high-voltage battery 1 [AX2], 82 kWh

Voltage and insulation measurement, 48, 55, 62 kWh

Voltage and insulation measurement

Special tools and workshop equipment required

  • high-voltage test module - VAS 6558-
  • high-voltage test module - VAS 6558AID.

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Put on the required protective equipment for the subsequent work steps ⇒ Electronic parts catalogue (ETKA) :

  • Arc flash resistant clothing (at least APC 2, at least 318 kJ)
  • Helmet with arc flash resistant visor (at least APC 2, at least 318 kJ)
  • Arc flash resistant gloves with nitrile glove liners (at least APC 2, at least 318 kJ), insulating up to at least 500 V
  • Safety shoes with ESD protection

All tests must be performed using high-voltage test module - VAS 6558A- / high-voltage test module - VAS 6558- and vehicle diagnostic tester. ⇒ Vehicle diagnostic tester

Preparing for the measurements

  • ⇒ Rep. gr. 93 ; Open high-voltage battery 1 [AX2] .
  • Select measuring method.
  • High-voltage system - overall functions
  • High-voltage test module VAS 6558/VAS 6558A
  • Voltage measurement
  • Select type of measurement/function
  • Low impedance voltage measurement
  • Perform continuous measurement
  • Check function of high-voltage test module - VAS 6558A- / -VAS 6558- on suitable voltage source. ( Battery - A- )

Checking voltage of high-voltage battery 1 - AX2-

  • Check voltage between high-voltage "positive" -1- and highvoltage "negative" -2-.
  • Make a note of the voltage of high-voltage battery 1 - AX2- .
Volkswagen ID.4. Checking voltage of high-voltage battery 1 - AX2-

Checking voltage between high-voltage "positive" and battery housing

  • Check voltage between high-voltage "positive" -1- and earth connection -3-.

Note

The voltage decreases during the measurement.

Important

  • Specification: max. 5 V
Volkswagen ID.4. Checking voltage of high-voltage battery 1 - AX2-

Checking voltage between high-voltage "negative" and battery housing

  • Check voltage between high-voltage "negative" -2- and earth connection -3-.

Note

The voltage decreases during the measurement.

Important

  • Specification: max. 5 V
Volkswagen ID.4. Checking voltage of high-voltage battery 1 - AX2-

Voltage and insulation measurement, 82 kWh

Voltage and insulation measurement

Special tools and workshop equipment required

  • high-voltage test module - VAS 6558-
  • high-voltage test module - VAS 6558ADANGER

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Put on the required protective equipment for the subsequent work steps ⇒ Electronic parts catalogue (ETKA) :

  • Arc flash resistant clothing (at least APC 2, at least 318 kJ)
  • Helmet with arc flash resistant visor (at least APC 2, at least 318 kJ)
  • Arc flash resistant gloves with nitrile glove liners (at least APC 2, at least 318 kJ), insulating up to at least 500 V
  • Safety shoes with ESD protection

All tests must be performed using high-voltage test module - VAS 6558A- / high-voltage test module - VAS 6558- and vehicle diagnostic tester. ⇒ Vehicle diagnostic tester

Preparing for the measurements

  • ⇒ Rep. gr. 93 ; Open high-voltage battery 1 [AX2] .
  • Select measuring method.
  • High-voltage system - overall functions
  • High-voltage test module VAS 6558/VAS 6558A
  • Voltage measurement
  • Select type of measurement/function
  • Low impedance voltage measurement
  • Perform continuous measurement
  • Check function of high-voltage test module - VAS 6558A- / -VAS 6558- on suitable voltage source. ( Battery - A- )

Checking voltage of high-voltage battery 1 - AX2-

  • Check voltage between high-voltage "positive" -1- and highvoltage "negative" -2-.
  • Make a note of the voltage of high-voltage battery 1 - AX2- .
Volkswagen ID.4. Voltage and insulation measurement, 82 kWh

Checking voltage between high-voltage "positive" and battery housing

  • Check voltage between high-voltage "positive" -1- and earth connection -3-.

Note

The voltage decreases during the measurement.

Important

  • Specification: max. 5 V
Volkswagen ID.4. Voltage and insulation measurement, 82 kWh

Checking voltage between high-voltage "negative" and battery housing

  • Check voltage between high-voltage "negative" -2- and earth connection -3-.

Note

The voltage decreases during the measurement.

Important

  • Specification: max. 5 V
Volkswagen ID.4. Voltage and insulation measurement, 82 kWh

Opening electrical circuit, 48, 55 kWh

Interrupting electrical circuit

Special tools and workshop equipment required

  • High-voltage tool kit - VAS 6762-
  • High-voltage tool kit - VAS 6883A-
  • Torque wrench - VAS 6883/1A-
  • contact protection - T10608-
  • contact protection - T10628-
  • voltage tester - VAS 6762/45-

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Put on protective equipment ⇒ Electronic parts catalogue (ETKA) before performing the following work steps:

  • Clothing approved for working with electric arcs (minimum protection class 2, at least 318 kJ)
  • Helmet with visor approved for working with electric arcs (minimum protection class 2, at least 318 kJ)
  • Gloves approved for working with electric arcs with nitrile glove liners (minimum protection class 2, at least 318 kJ), minimum insulating effect up to 500 V
  • Safety shoes with ESD protection

Removing

  • ⇒ Rep. gr. 93 ; Open high-voltage battery 1 AX2 .
  • Fit contact protection - T10628- -A- on battery module 1 - J991- -2-.
  • Remove bolts -3- on high-voltage connecting bracket -4- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 1 - J991- -2-.
  • Remove high-voltage connecting bracket -4- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 1 - J991- -2-.
  • Fit contact protection - T10608- on high-voltage connection at battery module 1 - J991- -2-.
Volkswagen ID.4. Opening electrical circuit, 48, 55 kWh
  • Fit contact protection - T10628- -A- on battery module 7 - J997- and battery module 8 - J998- .
  • Remove bolts -1- on high-voltage connecting bracket -2- between battery module 7 - J997- and battery module 8 - J998- .
  • Remove high-voltage connecting bracket -2- between battery module 7 - J997- and battery module 8 - J998- .
  • Fit contact protection - T10608- on open high-voltage connection on battery module 7 - J997- and battery module 8 - J998- .
Volkswagen ID.4. Opening electrical circuit, 48, 55 kWh

Installing

  • Fit contact protection - T10628- -A- on battery module 7 - J997- and battery module 8 - J998- .
  • Tighten bolts -1- for high-voltage connecting bracket -2- to specified torque immediately.
  • Have a second person check the torques.
  • Detach contact protection - T10628- -A-.
Volkswagen ID.4. Opening electrical circuit, 48, 55 kWh
  • Fit contact protection - T10628- -A- on battery module 1 - J991- -2-.

Note

When performing measurement before installing last battery connector, a voltage can be measured when switching unit for high-voltage battery, positive terminal - SX8- is installed. In this case, a load can be applied by pressing both buttons on voltage tester - VAS 6762/45- . If voltage tester - VAS 6762/45- no longer shows any voltage with load applied, work may be continued.

  • Before installing high-voltage connecting bracket -4-, measure voltage using voltage tester - VAS 6762/45- .
Volkswagen ID.4. Opening electrical circuit, 48, 55 kWh

DANGER

Wrong installation of battery modules and module connectors.

Risk of severe injury or death due to short-circuit with electric arc.

  • Check battery modules and module connectors for proper installation.
  • Proceed with the work only if there is no voltage between the battery terminals.

Important

  • No voltage is shown when load is applied.
  • Tighten bolts -3- on high-voltage connecting bracket -4- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 1 - J991- -2- immediately to specified torque.
  • Have a second person check the torques.
  • Detach contact protection - T10628- -A-.
  • Remaining installation steps are carried out in reverse sequence; note the following:

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - high-voltage battery, battery modules

Opening electrical circuit, 62 kWh

Opening electrical circuit

Special tools and workshop equipment required

  • High-voltage tool kit - VAS 6762-
  • High-voltage tool kit - VAS 6883A-
  • Torque wrench - VAS 6883/1A-
  • accidental contact protection - T10608-
  • accidental contact protection insert - T10628-
  • voltage tester - VAS 6762/45-

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Put on the required protective equipment for the subsequent work steps ⇒ Electronic parts catalogue (ETKA) :

  • Arc flash resistant clothing (at least APC 2, at least 318 kJ)
  • Helmet with arc flash resistant visor (at least APC 2, at least 318 kJ)
  • Arc flash resistant gloves with nitrile glove liners (at least APC 2, at least 318 kJ), insulating up to at least 500 V
  • Safety shoes with ESD protection

Removing

  • ⇒ Rep. gr. 93 ; Open high-voltage battery 1 [AX2] .
  • Fit accidental contact protection insert - T10628- -A- onto battery module 5 - J995- -2-.
  • Unscrew bolts -3- on high-voltage connection -4- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 5 - J995- -2-.
  • Remove high-voltage connector -4- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 5 - J995- -2-.
  • Fit accidental contact protection - T10608- onto exposed high-voltage connection on battery module 5 - J995- -2-.
Volkswagen ID.4. Opening electrical circuit, 62 kWh
  • Fit accidental contact protection insert - T10628- -A- onto battery module 11 - J1001- and battery module 12 - J1002- .
  • Unscrew bolts -1- on high-voltage connector -2- between battery module 11 - J1001- and battery module 12 - J1002- .
  • Remove high-voltage connector -2- between battery module 11 - J1001- and battery module 12 - J1002- .
  • Fit accidental contact protection - T10608- onto exposed high-voltage connection on battery module 11 - J1001- and battery module 12 - J1002-
Volkswagen ID.4. Opening electrical circuit, 62 kWh

Installing

  • Fit accidental contact protection insert - T10628- -A- onto battery module 11 - J1001- and battery module 12 - J1002- .
  • Tighten bolts -1- from high-voltage connector -2- to specified torque straightaway.
  • Have an additional person observe torque settings.
  • Remove accidental contact protection insert - T10628- -A-.
Volkswagen ID.4. Opening electrical circuit, 62 kWh
  • Fit accidental contact protection insert - T10628- -A- onto battery module 5 - J995- -2-.

Note

If the measurement is taken before the last battery connector has been installed, a voltage can be measured with the switching unit for high-voltage battery, positive terminal - SX8- installed.

If this is the case, a load can be applied by pressing both buttons on the voltage tester - VAS 6762/45- . If the voltage tester - VAS 6762/45- no longer indicates voltage when the load is applied, the work sequence can be continued.

  • Prior to installing high-voltage connector -4-, carry out voltage measurement using voltage tester - VAS 6762/45- .
Volkswagen ID.4. Opening electrical circuit, 62 kWh

DANGER

Wrong installation of battery modules and module connectors.

Risk of severe injury or death due to short-circuit with electric arc.

  • Check battery modules and module connectors for proper installation.
  • Proceed with the work only if there is no voltage between the battery terminals.

Important

  • When the load is applied, no voltage is displayed.
  • Immediately tighten bolts -3- on high-voltage connector -4- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 5 - J995- -2- to specified torque.
  • Have an additional person observe torque settings.
  • Remove accidental contact protection insert - T10628- -A-.
  • Further installation is carried out in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - high-voltage battery, battery modules

Opening electrical circuit, 82 kWh

Interrupting electrical circuit

Special tools and workshop equipment required

  • High-voltage tool kit - VAS 6762-
  • High-voltage tool kit - VAS 6883A-
  • Torque wrench - VAS 6883/1A-
  • contact protection - T10608-
  • contact protection - T10628-
  • voltage tester - VAS 6762/45-

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Put on protective equipment ⇒ Electronic parts catalogue (ETKA) before performing the following work steps:

  • Clothing approved for working with electric arcs (minimum protection class 2, at least 318 kJ)
  • Helmet with visor approved for working with electric arcs (minimum protection class 2, at least 318 kJ)
  • Gloves approved for working with electric arcs with nitrile glove liners (minimum protection class 2, at least 318 kJ), minimum insulating effect up to 500 V
  • Safety shoes with ESD protection

Removing

  • ⇒ Rep. gr. 93 ; Open high-voltage battery 1 AX2 .
  • Fit contact protection - T10628- -A- on battery module 1 - J991- -4-.
  • Remove bolts -2- on high-voltage connecting bracket -3- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 1 - J991- -4-.
  • Remove high-voltage connecting bracket -3- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 1 - J991- -4-.
  • Fit contact protection - T10608- on high-voltage connection at battery module 1 - J991- -4-.
Volkswagen ID.4. Opening electrical circuit, 82 kWh
  • Fit contact protection - T10628- -A- on battery module 11 - J1001- and battery module 12 - J1002- .
  • Remove bolts -1- on high-voltage connecting bracket -2- between battery module 11 - J1001- and battery module 12 - J1002- .
  • Remove high-voltage connecting bracket -2- between battery module 11 - J1001- and battery module 12 - J1002- .
  • Fit contact protection - T10608- on open high-voltage connection on battery module 11 - J1001- and battery module 12 - J1002- .
Volkswagen ID.4. Opening electrical circuit, 82 kWh

Installing

  • Fit contact protection - T10628- -A- on battery module 11 - J1001- and battery module 12 - J1002- .
  • Tighten bolts -1- for high-voltage connecting bracket -2- to specified torque immediately.
  • Have a second person check the torques.
  • Detach contact protection - T10628- -A-.
Volkswagen ID.4. Opening electrical circuit, 82 kWh
  • Fit contact protection - T10628- -A- on battery module 1 - J991- -4-.
Volkswagen ID.4. Opening electrical circuit, 82 kWh

Note

When performing measurement before installing last battery connector, a voltage can be measured when switching unit for high-voltage battery, positive terminal - SX8- is installed. In this case, a load can be applied by pressing both buttons on voltage tester - VAS 6762/45- . If voltage tester - VAS 6762/45- no longer shows any voltage with load applied, work may be continued.

  • Before installing high-voltage connecting bracket -3-, measure voltage using voltage tester - VAS 6762/45- .

DANGER

Wrong installation of battery modules and module connectors.

Risk of severe injury or death due to short-circuit with electric arc.

  • Check battery modules and module connectors for proper installation.
  • Proceed with the work only if there is no voltage between the battery terminals.

Important

  • No voltage is shown when load is applied.
  • Tighten bolts -2- on high-voltage connecting bracket -3- between switching unit for high-voltage battery, positive terminal - SX8- -1- and battery module 1 - J991- -4- immediately to specified torque.
  • Have a second person check the torques.
  • Detach contact protection - T10628- -A-.
  • Remaining installation steps are carried out in reverse sequence; note the following:

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - high-voltage battery, battery modules

Removing and installing battery regulation control unit J840

Special tools and workshop equipment required

  • High-voltage tool kit - VAS 6762-
  • Torque wrench - VAS 6883/1AID

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Put on the required protective equipment for the subsequent work steps ⇒ Electronic parts catalogue (ETKA) :

  • Arc flash resistant clothing (at least APC 2, at least 318 kJ)
  • Helmet with arc flash resistant visor (at least APC 2, at least 318 kJ)
  • Arc flash resistant gloves with nitrile glove liners (at least APC 2, at least 318 kJ), insulating up to at least 500 V
  • Safety shoes with ESD protection

Important

  • The battery regulation control unit - J840- and switching unit for high-voltage battery, negative terminal - SX7- and switching unit for high-voltage battery, positive terminal - SX8- must be renewed together.

Removing

Removing battery regulation control unit [J840]

If battery regulation control unit - J840- is renewed, perform test plan for renewal of control unit:

  • Carry out function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • ⇒ Rep. gr. 93 ; Open high-voltage battery 1 [AX2] .
  • ⇒ Rep. gr. 93 ; Open electrical circuit .
  • Disconnect electrical connectors -3-, and place wiring harness aside.
  • Unscrew bolts -2-.
  • Remove battery regulation control unit - J840- -1-.
Volkswagen ID.4. Removing and installing battery regulation control unit J840

Removing switching unit for high-voltage battery, negative terminal [SX7] and switching unit for high-voltage battery, positive terminal [SX8]

  • ⇒ Rep. gr. 93 ; Removing and installing connector strip .

48, 55, 62 kWh

  • Detach cap for switching unit, positive terminal -1-.
Volkswagen ID.4. Removing and installing battery regulation control unit J840
  • Unscrew bolts -5-.
  • Remove carrier plate -6-.
  • Disconnect electrical connectors -3-, and place wiring harness aside.
Volkswagen ID.4. Removing and installing battery regulation control unit J840
  • Unscrew bolts -2-.
  • Remove switching unit, positive terminal -1-.
  • Unscrew bolts -3-.
  • Remove switching unit, negative terminal -4-.
Volkswagen ID.4. Removing and installing battery regulation control unit J840

All vehicles (continued)

82 kWh

  • Disconnect electrical connectors -3-, and move electrical wires -2- and -4- to one side.
Volkswagen ID.4. Removing and installing battery regulation control unit J840
  • Unscrew bolts -4-.
  • Remove switching unit, negative terminal -3-.
Volkswagen ID.4. Removing and installing battery regulation control unit J840

All vehicles (continued)

Installing

Installing switching unit for high-voltage battery, negative terminal [SX7] and switching unit for high-voltage battery, positive terminal [SX8] Install in reverse order of removal, observing the following:

If battery regulation control unit - J840- has been renewed, perform test plan for renewal of control unit:

  • Carry out function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Charging and discharging battery modules

Special tools and workshop equipment required

  • hood - VAS 6910/21-1-
  • insulating mat - VAS 6910/21-3-
  • module balancer - VAS 6910-

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Put on the required protective equipment for the subsequent work steps:

  • Arc flash resistant clothing (at least APC 2, at least 318 kJ)
  • Helmet with arc flash resistant visor (at least APC 2, at least 318 kJ)
  • Arc flash resistant gloves with nitrile glove liners (at least APC 2, at least 318 kJ), insulating up to at least 500 V
  • Safety shoes with ESD protection
  • ⇒ Rep. gr. 93 ; Open high-voltage battery 1 [AX2] .
  • ⇒ Rep. gr. 93 ; Open electrical circuit .

Important

  • If a new battery module is installed, it is essential to adapt the charge level using the module balancer - VAS 6910- .
  • Remove battery module ⇒ Rep. gr. 93 ; Overview of fitting locations - battery module .
  • Start autonomous software.

Note

Further instructions on how to proceed with charging/discharging using voltage balancing device for high-voltage battery module (module balancer) (module balancer) - VAS 6910- , hood - VAS 6910/21-1- and insulating mat - VAS 6910/21-3- can be gleaned from the autonomous software.

Checking whether upper part of battery housing can be reused

For it to be reused, upper part of battery housing must fulfil all criteria.

  • Place upper part of battery housing on flat surface. Check for the following:

Important

  • Upper part of battery housing -1- must not exhibit any signs of plastic deformation.
  • Foam seal -2- must not exhibit any cracks or abrasion.
  • No residue/detachment of foam seal on lower part of battery housing.
Volkswagen ID.4. Checking whether upper part of battery housing can be reused

Important

  • Foam seal is at same height all around.
  • Use depth gauge -B- at measuring points -2- to check height of foam seal. To do this, position at groove edge -4- and foam seal -3-.

Important

  • Height of foam seal -a- at least 2 mm.
Volkswagen ID.4. Checking whether upper part of battery housing can be reused

NOTICE

Contamination on upper part of battery housing.

During cleaning of upper part of battery housing, dirt on cleaning cloth will damage foam seal.

  • Remove contaminated sealant, soiling or foreign material in area -3- of upper part of battery housing -1- using lint-free cleaning cloth and cleaning solution ⇒ Electronic parts catalogue (ETKA) .

Important

  • Foam seal -2- must not exhibit any cracks or abrasion.
Volkswagen ID.4. Checking whether upper part of battery housing can be reused

Renewing lower part of battery housing

Removing

  • ⇒ Rep. gr. 93 ; Visual inspection of high-voltage battery 1 [AX2] .
  • Rep. gr. 93 ; Diagnosis of high-voltage battery 1 [AX2] .
  • Remove high-voltage battery 1 - AX2- ⇒ Rep. gr. 93 ; Removing and installing high-voltage battery 1 [AX2] .
  • ⇒ Rep. gr. 93 ; Leakage test of high-voltage battery 1 [AX2] .
  • ⇒ Rep. gr. 93 ; Open high-voltage battery 1 [AX2] .
  • ⇒ Rep. gr. 93 ; Voltage and insulation measurement .
  • ⇒ Rep. gr. 93 ; Open electrical circuit .
  • Remove connector strip ⇒ Rep. gr. 93 ; Removing and installing connecting element .
  • Remove battery regulation control unit - J840- ⇒ Rep.

    gr. 93 ; Removing and installing battery regulation control unit [J840] .

  • Remove switching unit for high-voltage battery, negative terminal - SX7- ⇒ Rep. gr. 93 ; Removing and installing switching unit for high-voltage battery, negative terminal [SX7] .
  • Remove switching unit for high-voltage battery, positive terminal - SX8- ⇒ Rep. gr. 93 ; Removing and installing switching unit for high-voltage battery, positive terminal [SX8] .
  • Remove battery modules control unit ⇒ Rep. gr. 93 ; Removing and installing battery modules control unit .
  • Remove battery modules alternately ⇒ Rep. gr. 93 ; Removing battery module .
  • Remove potential equalisation lines on high-voltage battery 1 - AX2- ⇒ Rep. gr. 93 ; Overview of fitting locations - potential equalisation lines .

Installing

  • Renew lower part of battery housing.
  • Install potential equalisation lines to high-voltage battery 1 - AX2- ⇒ Rep. gr. 93 ; Overview of fitting locations - potential equalisation lines .

Important

  • When installing the battery modules, always install one battery module completely, and then proceed with the next one.
  • ⇒ Rep. gr. 93 ; Install battery module .
  • Install battery modules control unit ⇒ Rep. gr. 93 ; Removing and installing battery modules control unit .
  • Install switching unit for high-voltage battery ⇒ Rep. gr. 93 ; Removing and installing switching unit for high-voltage battery, negative terminal [SX7] ⇒ Rep. gr. 93 ; Removing and installing switching unit for high-voltage battery, positive terminal [SX8] .
  • Install battery regulation control unit - J840- ⇒ Rep.

    gr. 93 ; Removing and installing battery regulation control unit [J840] .

  • Clean contact surfaces of connector strip.
  • Install connector strip ⇒ Rep. gr. 93 ; Removing and installing connecting element .
  • Close electrical circuit ⇒ Rep. gr. 93 ; Opening electrical circuit .
  • ⇒ Rep. gr. 93 ; Voltage and insulation measurement .

For it to be reused, upper part of battery housing from repair kit must fulfil all criteria.

  • Place upper part of battery housing on flat surface. Check for the following:

Important

  • Upper part of battery housing -1- must not exhibit any signs of plastic deformation.
  • Foam seal -2- must not exhibit any cracks or abrasion.
  • No residue/detachment of foam seal on lower part of battery housing.
Volkswagen ID.4. Renewing lower part of battery housing

Important

  • Foam seal is at same height all around
  • Use depth gauge -B- at measuring points -2- to check height of foam seal. To do this, position at groove edge -4- and foam seal -3-.

Important

  • Height of foam seal -a- at least 2 mm.

    Continued

Volkswagen ID.4. Renewing lower part of battery housing

Continued

  • ⇒ Rep. gr. 93 ; Seal high-voltage battery 1 [AX2] .
  • ⇒ Rep. gr. 93 ; Check warning stickers .
  • ⇒ Rep. gr. 93 ; Leakage test of high-voltage battery 1 [AX2] .
  • Install high-voltage battery 1 - AX2- ⇒ Rep. gr. 93 ; Removing and installing high-voltage battery 1 [AX2] .
  • ⇒ Rep. gr. 93 ; Diagnosis of high-voltage battery 1 [AX2] .
  • ⇒ Rep. gr. 93 ; Visual inspection of high-voltage battery 1 [AX2] .
  • Road test vehicle.

Renewing high-voltage battery 1 [AX2]

The high-voltage battery 1 - AX2- will subsequently be referred to as "high-voltage battery".

  • Make sure that all separating films -2- of high-voltage battery -1- are present ⇒ Rep. gr. 93 ; Assembly overview - removed high-voltage battery .
Volkswagen ID.4. Renewing high-voltage battery 1 [AX2]

NOTICE

Potential damage to vehicle

  • The inserted bolts in the new high-voltage battery must be removed before placing it on the scissor-type assembly platform.
  • Prepare high-voltage battery for lifting ⇒ Rep. gr. 93 ; Lifting high-voltage battery 1 [AX2] .
  • Lift high-voltage battery 20 cm out of packaging and leave it above packaging.
  • Press out inserted bolts downwards using commercially available tools.