Dash panel insert

In this manual: Dash panel insert
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
2steps
~12min
1/5difficulty
0102030405032N·mlb·ft
Tightening torque found on this page
Done 0 of 2
  • Assembly overview - control unit with display unit for driver information system
  • Removing and installing control unit with display unit for driver information system [J1254]
  • Removing and installing control unit for head-up display [J898]
  • Calibrating control unit for head-up display [J898]

Assembly overview - control unit with display unit for driver information system

Volkswagen ID.4. Assembly overview - control unit with display unit for driver information system
  1. Gap cover for dash panel insert
  • ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/ covers; Assembly overview - steering column trim
  1. Trim for control unit with display unit for driver information system - J1254-
  2. Bolt
  • Qty. 6
  • 3 N·m
  1. Driving mode selector
  • Cannot be renewed individually
  • Depending on equipment/ version
  • Functions stored in steering column electronics control unit - J527-
  • ⇒ Rep. gr. 94 ; Removing and installing steering column electronics control unit [J527]
  1. Control unit with display unit for driver information system - J1254-
  • ⇒ Rep. gr. 90 ; Removing and installing control unit with display unit for driver information system [J1254]
  1. Upper steering column trim
  • ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Assembly overview - steering column trim
  1. Electrical connector

Assembly overview - head-up display

Volkswagen ID.4. Assembly overview - head-up display
  1. Bolt
  • Qty. 4
  • 4,5 N·m
  1. Control unit for head-up display - J898-
  • ⇒ Rep. gr. 90 ; Removing and installing control unit for head-up display [J898]
  • ⇒ Rep. gr. 90 ; Calibrating control unit for head-up display [J898]
  1. Bolt
  • Qty. 6
  • 1,2 N·m

Removing and installing control unit with display unit for driver information system [J1254]

The control unit with display unit for driver information system - J1254- will henceforth be referred to as "display unit".

Removing

If display unit is renewed:

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Move steering wheel to rearmost and lowest position. Use full adjustment range of steering column for this purpose.
  • Remove gap cover for dash panel insert ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing dash panel insert gap cover .
  • Use a commercially available plastic wedge to unclip trim -1-.
Volkswagen ID.4. Removing and installing control unit with display unit for driver information system [J1254]
  • Disconnect electrical connector -2-.
  • Secure display unit against falling out.
  • Unscrew bolts -1-.
  • Remove display unit.
Volkswagen ID.4. Removing and installing control unit with display unit for driver information system [J1254]

Installing

Install in the reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 90 ; Assembly overview - control unit with display unit for driver information system

Removing and installing control unit for head-up display [J898]

Control unit for head-up display - J898- is referred to hereafter as control unit.

Dynamic light strip 3 for information in dash panel - L385- is referred to hereafter as light strip.

Removing

If control unit is renewed:

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Remove windscreen ⇒ General body repairs, exterior; Rep. gr. 64 ; Windscreen; Removing and installing windscreen .
  • Remove light strip ⇒ Rep. gr. 96 ; Removing and installing dynamic light strip 3 for information in dash panel [L385] .
  • Remove cover for dash panel/head-up display ⇒ General body repairs, interior; Rep. gr. 70 ; Removing and installing cover for dash panel/head-up display .
  • Place dash panel insulation to one side.
  • Cover control unit -1- with a soft cleaning cloth.
  • Unscrew bolts -arrows-.
  • Remove control unit -1-, and disconnect electrical connector.
Volkswagen ID.4. Removing and installing control unit for head-up display [J898]

Installing

Install in the reverse order of removal, observing the following:

If control unit is renewed:

  • On new part, unscrew bolts -2-.
  • Detach actuator plates -3- from control unit -1-.
Volkswagen ID.4. Removing and installing control unit for head-up display [J898]

All vehicles (continued)

NOTICE

Risk of damage to control unit for head-up display.

  • Never apply pressure to the upper part of the housing when inserting.
  • Should a control unit for head-up display fall down, it must be renewed.
  • Insert control unit -1-.
  • Connect electrical connectors.
  • Tighten bolts -arrows-.
  • Position windscreen and secure it temporarily with adhesive tape - do not bond it in yet.
  • Switch on ignition.
  • Perform functional check.
  • Install windscreen ⇒ General body repairs, exterior; Rep. gr. 64 ; Windscreen; Removing and installing windscreen .
  • Calibrate control unit ⇒ Rep. gr. 90 ; Calibrating control unit for head-up display [J898] .
Volkswagen ID.4. Removing and installing control unit for head-up display [J898]

Tightening torques

  • ⇒ Rep. gr. 90 ; Assembly overview - head-up display

Calibrating control unit for head-up display [J898]

Calibrating control unit for head-up display [J898], left-hand drive vehicles

Special tools and workshop equipment required

  • calibration board for head-up display AR - VAS 721 019-
  • setting device - VAS 6430-

Control unit for head-up display - J898- is referred to hereafter as control unit.

Calibrate control unit if the following applies:

  • Installation position of dash panel cross member has been changed.
  • Dash panel cross member was removed and reinstalled.
  • Windscreen was removed and reinstalled.
  • Lock carrier was removed and reinstalled or renewed.

Calibration

  • ⇒ Driver assist systems; Rep. gr. 98 ; Front camera for driver assist systems; Calibrating front camera for driver assist systems [R242] .
  • Use display unit for front information display and operating unit control unit - J685- to set lower limit position of control unit and then increase setting by 10 increments.
  • Fold down left and right sun visors, detach and swivel to one side.
  • Attach calibration board for head-up display AR - VAS 721 019- -1- to sun visor centre mount -2- and align.
  • Remove cover for dash panel/head-up display ⇒ General body repairs, interior; Rep. gr. 70 ; Removing and installing cover for dash panel/head-up display .
  • Carry out function "Activate test screen" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • Check position of test screen through hole of calibration panel -1- on driver side.
Volkswagen ID.4. Calibrating control unit for head-up display [J898]

Vehicles with incorrectly positioned test screen:

Note

During manual adjustment, it may happen that not all contours of the head-up display test screen can be positioned well on the setting device - VAS 6430- . This is due to the tolerances in the head-up display system and the resulting distortion. In this case, mainly the elements in the middle of the image area should be brought into the best possible alignment. Deviations for elements in the outer image area are allowed.

Bring test screen -1- into best possible alignment using setting device -A- via adjuster screws -3- on control unit -2-.

Volkswagen ID.4. Calibrating control unit for head-up display [J898]

All vehicles (continued)

Installing

Install in reverse order of removal.

Calibrating control unit for head-up display [J898], right-hand drive vehicles

Special tools and workshop equipment required

  • calibration board for head-up display AR - VAS 721 019-
  • setting device - VAS 6430-

Control unit for head-up display - J898- is referred to hereafter as control unit.

Calibrate control unit for head-up display, if:

  • Installation position of dash panel cross member has been changed.
  • Dash panel cross member was removed and reinstalled.
  • Windscreen was removed and reinstalled.
  • Lock carrier was removed and reinstalled or renewed.

Calibration

  • ⇒ ; Rep. gr. ; Calibrating front camera for driver assist systems [R242], static .
  • Use display unit for front information display and operating unit control unit - J685- to set lower limit position of control unit and then increase setting by 10 increments
  • Fold down left and right sun visors, detach and swivel to one side.
  • Attach calibration board for head-up display AR - VAS 721 019- -1- to sun visor centre mount -2-, and align it centrally.
  • Remove cover for dash panel/head-up display ⇒ General body repairs, interior; Rep. gr. 70 ; Removing and installing cover for dash panel/head-up display .
  • Carry out function "Activate test screen" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • Check position of test screen through hole of calibration panel -1- on driver side.
Volkswagen ID.4. Calibrating control unit for head-up display [J898]

Vehicles with incorrectly positioned test screen:

Note

During manual adjustment, it may happen that not all contours of the head-up display test screen can be positioned well on the setting device - VAS 6430- . This is due to the tolerances in the head-up display system and the resulting distortion. In this case, mainly the elements in the middle of the image area should be brought into the best possible alignment. Deviations for elements in the outer image area are allowed.

  • Bring test screen -1- into best possible alignment using setting device -A- via adjuster screws -3- on control unit -2-.
Volkswagen ID.4. Calibrating control unit for head-up display [J898]

All vehicles (continued)

Installing

Install in reverse order of removal.