Assembly overview - front right longitudinal member, part section

In this manual: Assembly overview - front right longitudinal member, part section
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
15steps
~90min
4/5difficulty
Done 0 of 15
  1. Front longitudinal member
  • ⇒ Rep. gr. 50; Renewing front right longitudinal member, part section
  1. Separating cut
  2. Bonded area
    Volkswagen ID.4. Assembly overview - front right longitudinal member, part section

Assembly overview - front right longitudinal member, part section (second separating cut)

  1. Front longitudinal member
  • ⇒ Rep. gr. 50; Renewing front right longitudinal member, part section (second separating cut)
  1. Front longitudinal member cross panel
  2. Retainer for brake hose
  3. Cover plate for front longitudinal member
  4. Moulded foam insert
  • ⇒ Rep. gr. 00; Moulded foam inserts
  1. Web plate
  2. Separating cut
  3. Web plate for front longitudinal member
  4. Pipe set bracket
  5. Mounting bracket for subframe
  6. Bonded areas
    Volkswagen ID.4. Assembly overview - front right longitudinal member, part section (second separating cut)

Assembly overview - upper longitudinal member

Overview is shown for left side of vehicle as an example

  1. Upper longitudinal member
  • ⇒ Rep. gr. 50; Renewing upper longitudinal member
  1. Web plate
  2. Bonded areas
  3. Separating cut
    Volkswagen ID.4. Assembly overview - upper longitudinal member
  • Assembly overview - upper inner longitudinal member
  • Renewing front left longitudinal member, part section (2nd separating cut)
  • Renewing front right longitudinal member, part section
  • Renewing front right longitudinal member, part section (second separating cut)
  • Renewing upper longitudinal member
  • Renewing upper inner longitudinal member

Assembly overview - upper inner longitudinal member

Overview is shown for left side of vehicle as an example

  1. Upper inner longitudinal member
  • ⇒ Rep. gr. 50; Renewing upper inner longitudinal member
  1. Bonded areas
Volkswagen ID.4. Assembly overview - upper inner longitudinal member

Renewing front left longitudinal member, part section

WARNING

Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

  • Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
  • Use an extraction system during work.

NOTICE

If separating cuts are made too deep, underlying reinforcement could be damaged.

  • Only make separating cuts with body saw.
  • Rewelding of reinforcements is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

  • RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

Strength could be impaired if continuous seam is changed

  • SG continuous weld seam must not be reworked (ground or smoothed).

NOTICE

If adhesive is applied prematurely, bond could be impaired

  • New part must be welded in within 90 minutes.

Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1

Removing

  • Mark separating cut -2- all around on front longitudinal member -1- in accordance with dimension -a- and cut in straight line.
Volkswagen ID.4. Renewing front left longitudinal member, part section
  • Dimension -a- = 83 mm
  • Separate original joint.
  • Remove longitudinal member part section -1-.
  • Mark parting cut -2- on front longitudinal member -1- in accordance with dimension -a-, and make parting cut in a straight line.
Volkswagen ID.4. Renewing front left longitudinal member, part section
  • Dimension -a- = 40 mm
  • Separate original joint.
  • Remove remainder of longitudinal member -1-.
  • Remove remaining material.
Volkswagen ID.4. Renewing front left longitudinal member, part section
  • Completely remove remaining adhesive.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.

Installing

Replacement parts

  • For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)

Important

  • New parts must be adapted and attached with the vehicle standing on the straightening bracket set.
  • Grind bonding surfaces and welding surfaces on new part -1- down to bare metal and clean.
Volkswagen ID.4. Renewing front left longitudinal member, part section
  • Transfer separating cut -2- to new part -1-, and cut in a straight line.
Volkswagen ID.4. Renewing front left longitudinal member, part section
  • Transfer separating cut -3- to new part -4-, and cut in a straight line.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.
  • Apply 2-component body adhesive over entire area of RP spot weld seam.
Volkswagen ID.4. Renewing front left longitudinal member, part section
  • Adjust new part -1- and -2- to fit and fix in position.
  • Check fit with add-on parts.
  • Weld in new part -1- and -2-, RP spot weld seam and SG continuous weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing front left longitudinal member, part section
  • Adapt new part -1- to fit and fix in position.
  • Check fit with add-on parts.
  • Weld in new part -1-, RP spot weld seam.

Vehicles with studs.

Renew studs.

Renewing front left longitudinal member, part section (2nd separating cut)

WARNING

Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

  • Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
  • Use an extraction system during work.

NOTICE

If separating cuts are made too deep, underlying reinforcement could be damaged.

  • Only make separating cuts with body saw.
  • Rewelding of reinforcements is not permitted due to safety reasons.

NOTICE

Strength could be impaired if continuous seam is changed

  • SG continuous weld seam must not be reworked (ground or smoothed).

NOTICE

If adhesive is applied prematurely, bond could be impaired

  • New part must be welded in within 90 minutes.

Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1

Removing

  • Mark separating cut -2- on cover plate for front longitudinal member -1- in accordance with dimension -a- and cut in a straight line.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Dimension -a- = 15 mm
  • Separate original joint.
  • Remove front longitudinal member cover plate -1-.
  • Remove any foam residue -3-.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Mark parting cut -2- on front longitudinal member -1- in accordance with dimension -a-, and make parting cut in a straight line.
  • Dimension -a- = 55 mm
  • Separate original joint.
  • Remove front longitudinal member -1-.
  • Remove remaining material on original joint -1-.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Remove remaining material.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.

Installing

Replacement parts

  • For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)

Important

  • New parts must be adapted and attached with the vehicle standing on the straightening bracket set.

Grind bonding surfaces and welding surfaces on new part -1- down to bare metal and clean.

Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Transfer separating cut -2- to new part -1-, and cut in a straight line.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Transfer separating cut -3- to new part -4-, and cut in a straight line.
  • Drill 8 mm diameter holes for SG plug weld seam in new part -6-.
  • Grind bonding surfaces and welding surfaces on new part -1- to -7- down to bare metal and clean.

Important

  • Exact position of new parts must be carried over from old part.
  • Grind welding surfaces back to bare metal and clean.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Apply 2-component body adhesive to entire surface.
  • Adapt new part -2- to new part -1- via hole, and fix in position.
  • Adapt new part -4- to new part -3-, and fix in position.
  • Weld in new part -1- and -4-, RP spot weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Check fit with add-on parts.
  • Weld in new part -1-, SG continuous weld seam and RP spot weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Adapt new part -1- to fit via hole, and fix it in position.
  • Check fit with add-on parts.
  • Weld in new part -1- (SG plug weld seam and RP spot weld seam).
  • Prepare moulded foam insert -2- for installation and insert.
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Check fit with add-on parts.
  • Weld in new part -1-, SG continuous weld seam and RP spot weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing front left longitudinal member, part section (2nd separating cut)
  • Adapt new part -1- to fit and fix in position.
  • Check fit with add-on parts.
  • Weld in new part -1-, RP spot weld seam.
  • Install battery tray ⇒ Rep. gr. 50; Renewing battery tray.

Vehicles with studs.

Renew studs.

Renewing front right longitudinal member, part section

WARNING

Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

  • Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
  • Use an extraction system during work.

NOTICE

If separating cuts are made too deep, underlying reinforcement could be damaged.

  • Only make separating cuts with body saw.
  • Rewelding of reinforcements is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

  • RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

Strength could be impaired if continuous seam is changed

  • SG continuous weld seam must not be reworked (ground or smoothed).

NOTICE

If adhesive is applied prematurely, bond could be impaired

  • New part must be welded in within 90 minutes.

Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1

Removing

  • Mark separating cut -2- all around on front longitudinal member -1- in accordance with dimension -a- and cut in straight line.
Volkswagen ID.4. Renewing front right longitudinal member, part section
  • Dimension -a- = 83 mm
  • Separate original joint.
  • Remove longitudinal member part section -1-.
  • Mark parting cut -2- on front longitudinal member -1- in accordance with dimension -a-, and make parting cut in a straight line.
Volkswagen ID.4. Renewing front right longitudinal member, part section
  • Dimension -a- = 40 mm
  • Separate original joint.
  • Remove remainder of longitudinal member -1-.
  • Remove remaining material.
Volkswagen ID.4. Renewing front right longitudinal member, part section
  • Completely remove remaining adhesive.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.

Installing

Replacement parts

  • For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)

Important

  • New parts must be adapted and attached with the vehicle standing on the straightening bracket set.
  • Grind bonding surfaces and welding surfaces on new part -1- down to bare metal and clean.
Volkswagen ID.4. Renewing front right longitudinal member, part section
  • Transfer separating cut -2- to new part -1-, and cut in a straight line.
Volkswagen ID.4. Renewing front right longitudinal member, part section
  • Transfer separating cut -3- to new part -4-, and cut in a straight line.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.
  • Apply 2-component body adhesive over entire area of RP spot weld seam.
Volkswagen ID.4. Renewing front right longitudinal member, part section
  • Adjust new part -1- and -2- to fit and fix in position.
  • Check fit with add-on parts.
  • Weld in new part -1- and -2-, RP spot weld seam and SG continuous weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing front right longitudinal member, part section
  • Adapt new part -1- to fit and fix in position.
  • Check fit with add-on parts.
  • Weld in new part -1-, RP spot weld seam.

Vehicles with studs.

Renew studs.

Renewing front right longitudinal member, part section (second separating cut)

WARNING

Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

  • Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
  • Use an extraction system during work.

NOTICE

If separating cuts are made too deep, underlying reinforcement could be damaged.

  • Only make separating cuts with body saw.
  • Rewelding of reinforcements is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

  • RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

Strength could be impaired if continuous seam is changed

  • SG continuous weld seam must not be reworked (ground or smoothed).

NOTICE

If adhesive is applied prematurely, bond could be impaired

  • New part must be welded in within 90 minutes.

Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1

Removing

  • Mark separating cut -2- on cover plate for front longitudinal member -1- in accordance with dimension -a- and cut in a straight line.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Dimension -a- = 15 mm
  • Separate original joint.
  • Remove front longitudinal member cover plate -1-.
  • Remove any foam residue -3-.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Mark parting cut -2- on front longitudinal member -1- in accordance with dimension -a-, and make parting cut in a straight line.
  • Dimension -a- = 55 mm
  • Separate original joint.
  • Remove front longitudinal member -1-.
  • Separate original joint on remaining material -1-.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Remove remaining material.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.

Installing

Replacement parts

  • For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)

Important

  • New parts must be adapted and attached with the vehicle standing on the straightening bracket set.
  • Grind bonding surfaces and welding surfaces on new part -1- down to bare metal and clean.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Transfer separating cut -2- to new part -1-, and cut in a straight line.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Transfer separating cut -4- to new part -3-, and cut in a straight line.
  • Drill 8 mm diameter holes for SG plug weld seam in new part -8-.
  • Grind bonding surfaces and welding surfaces on new part -1- to -8- down to bare metal and clean.

Important

  • Exact position of new parts must be carried over from old part.
  • Grind welding surfaces back to bare metal and clean.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Apply 2-component body adhesive to entire surface.
  • Adapt new part -2- to new part -1- via hole, and fix in position.
  • Adapt new part -3- to new part -1-, and fix in position.
  • Adapt new part -5- to new part -4-, and fix in position.
  • Weld in new part -1- and -5-, RP spot weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Check fit with add-on parts.
  • Weld in new part -1-, SG continuous weld seam and RP spot weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Adapt new part -1- to fit via hole, and fix it in position.
  • Check fit with add-on parts.
  • Weld in new part -1-, SG plug weld seam and RP spot weld seam.
  • Prepare moulded foam insert -2- for installation and insert.
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Check fit with add-on parts.
  • Weld in new part -1-, SG continuous weld seam and RP spot weld seam.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing front right longitudinal member, part section (second separating cut)
  • Adapt new part -1- to fit and fix in position.
  • Check fit with add-on parts.
  • Weld in new part -1-, RP spot weld seam.

Vehicles with studs.

Renew studs.

Renewing upper longitudinal member

WARNING

Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

  • Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
  • Use an extraction system during work.

NOTICE

If separating cuts are made too deep, underlying reinforcement could be damaged.

  • Only make separating cuts with body saw.
  • Rewelding of reinforcements is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

  • RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

If adhesive is applied prematurely, bond could be impaired

  • New part must be welded in within 90 minutes.

Observe safety information ⇒ Rep. gr. 00; Safety information

Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1.

Removal and installation are described for left side of vehicle as an example.

Removing

  • Make separating cut -2- on upper longitudinal member -1- as shown.
Volkswagen ID.4. Renewing upper longitudinal member
  • Separate original joint.
  • Remove upper longitudinal member -1-.
  • Remove remaining material.
Volkswagen ID.4. Renewing upper longitudinal member
  • Completely remove remaining adhesive.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.

Installing

Replacement parts

  • For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)

Important

  • New parts must be adapted and attached with the vehicle standing on the straightening bracket set.
  • Transfer separating cut -2- to new part -1- and cut.
Volkswagen ID.4. Renewing upper longitudinal member
  • Drill 8 mm diameter holes for SG plug weld seam in new part -1-.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing upper longitudinal member
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing upper longitudinal member
  • Check fit with add-on parts.
  • Weld in new part -1-, SG plug weld seam and RP spot weld seam.
  • Weld parting cut, SG stepped weld seam.

Renewing upper inner longitudinal member

WARNING

Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

  • Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
  • Use an extraction system during work.

NOTICE

Do not damage underlying reinforcements.

Rewelding of reinforcement is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

  • RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

If adhesive is applied prematurely, bond could be impaired

  • New part must be welded in within 90 minutes.

Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1

Removal and installation are described for left side of vehicle as an example.

Removing

Upper longitudinal member already removed ⇒ Rep. gr. 50; Renewing upper longitudinal member

  • Separate original joint.
Volkswagen ID.4. Renewing upper inner longitudinal member
  • Remove upper inner longitudinal member -1-.
  • Remove remaining material.
Volkswagen ID.4. Renewing upper inner longitudinal member
  • Completely remove remaining adhesive.
  • Grind bonding surfaces and welding surfaces back to bare metal and clean.

Installing

Replacement parts

  • For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)

Important

  • New parts must be adapted and attached with the vehicle standing on the straightening bracket set.
  • Grind bonding surfaces and welding surfaces on new part -1- down to bare metal and clean.
Volkswagen ID.4. Renewing upper inner longitudinal member
  • Apply 2-component body adhesive to entire surface.
Volkswagen ID.4. Renewing upper inner longitudinal member
  • Adapt new part -1- to fit and fix in position.
Volkswagen ID.4. Renewing upper inner longitudinal member
  • Check fit with add-on parts.
  • Weld in new part -1- (SG plug weld seam, SG continuous weld seam and RP spot weld seam).
  • Install upper part of longitudinal member ⇒ Rep. gr. 50; Renewing upper part of longitudinal member.