Wheel alignment

In this manual: Wheel alignment
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~6min read
  • Notes on wheel alignment
  • Adjusting camber at front wheels
  • Adjusting toe setting at rear wheels
  • Checking full steering lock

Notes on wheel alignment

Wheel alignment must always be performed using wheel alignment equipment approved for the relevant brand.

All information required for wheel alignment is provided by the wheel alignment computer.

Vehicles pulling to one side; accident vehicles

This may be due to the rack not being positioned exactly in the centre of the steering rack unit when driving in a straight line.

This is enough to result in slight steering assistance in one direction, which causes the vehicle to pull to the left or right.

Test requirements

A wheel alignment platform and wheel alignment units which have been tested and correctly adjusted are basic requirements.

Suspension, wheel bearings and steering must have been checked for excessive play and damage.

Tread depth difference must be no more than 2 mm on one axle.

Tyres inflated to correct pressures.

Vehicle must be at unladen weight.

Spare wheel must be in specified location in vehicle.

Tool kit must be in specified location in vehicle.

Sliding plates and turntables must not be touching the end stop during the alignment procedure.

Alignment unit must be properly attached and adjusted; refer to operating instructions of equipment manufacturer.

Initial instruction must have been provided by manufacturer of wheel alignment unit.

Wheel alignment specifications

Camber is not adjustable on front axle. Only minor corrections can be achieved by shifting subframe.

Toe-out on turns can also be displayed as a negative value on the wheel alignment computer, depending on the manufacturer.

Measuring ride height

  • Ride height is defined by dimension -a- between centre of wheel hub and lower edge of wheel housing.
Volkswagen ID.4. Notes on wheel alignment

Setting vehicle to initial position for wheel alignment

If ride height is not as specified ⇒ Rep. gr. 44 ; Specifications for wheel alignment :

Volkswagen ID.4. Setting vehicle to initial position for wheel alignment
  • Front axle: balance out ride height by adding weights to respective suspension turret.
  • Rear axle: balance out ride height by placing weights in luggage compartment at respective side.

When does wheel alignment have to be checked?

Wheel alignment must be checked:

  • If there are problems with handling caused by the running gear
  • If the vehicle has been involved in an accident or components have been renewed
  • If suspension components have been removed or renewed
  • If tyres are worn unevenly.

Components renewed

All vehicles (continued)

Adjusting camber at front wheels

Front axle camber cannot be adjusted; it can only be corrected slightly by moving the subframe.

The subframe may be moved to the left or right, but NOT forwards or backwards in a longitudinal direction.

  • Remove underbody trim (front) ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody trim; Removing and installing underbody trim (front) .
  • Remove bolts -2- one by one and screw in new bolts loosely.
  • Only remove next bolt -2- after replacing previously removed bolt with a new bolt -2-.

The camber adjustment range is limited by the tolerances of the holes in the subframe -1-. If the specified value is not obtained by moving the subframe -1-, the subframe and the body must be inspected.

  • Camber can now be adjusted to specification by moving subframe -1-.
  • Move subframe -1- sideways until camber is the same on both sides ⇒ Rep. gr. 44 ; Wheel alignment specifications .
  • Tighten bolts -2-.
Volkswagen ID.4. Adjusting camber at front wheels

Tightening torques

  • ⇒ Rep. gr. 40 ; Exploded view - subframe
  • ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody trim; Exploded view - underbody trim

Adjusting camber at rear wheels

  • Loosen nut -4- on inside of spring control arm -3-.
  • Adjust camber by turning eccentric bolt -2-.

Note

Maximum adjustment range is 90º to left or right of centre position.

  • Tighten new nut -4-, counterholding at eccentric bolt -2-.
Volkswagen ID.4. Adjusting camber at front wheels
  • Check camber meets specification ⇒ Rep. gr. 44 ; Wheel alignment specifications .

Tightening torques

  • ⇒ Rep. gr. 42 ; Exploded view - spring control arm

Adjusting toe setting at rear wheels

  • Loosen nut -5- on inside of track rod -3-.
  • Adjust toe setting by turning eccentric bolt -2-.

Note

The maximum adjustment range is 90º to the left or right of the centre position.

  • Tighten new nut -5-, counterholding at eccentric bolt -2-.
Volkswagen ID.4. Adjusting toe setting at rear wheels
  • Check toe setting meets specification ⇒ Rep. gr. 44 ; Wheel alignment specifications .

Tightening torques

  • ⇒ Rep. gr. 42 ; Exploded view - track rod

Adjusting toe setting at front wheels

  • Loosen nut -2- (counterhold at hexagon flats -arrow A- on track rod -1-).
  • Loosen track rod -1- at track rod ball joint -3-. To do so, apply suitable tool at hexagon flats -arrow A- and -arrow B-.
  • Adjust toe setting at left and right wheels by turning hexagon flats -arrow A-. When doing this, counterhold at hexagon flats -arrow B-.
Volkswagen ID.4. Adjusting toe setting at front wheels

NOTICE

Risk of damage to boots if they are twisted.

  • Make sure boot on steering rack is not damaged or twisted.

    Twisted rubber boots wear out quickly.

  • Only tighten lock nut for threaded piece with vehicle standing on the ground.
  • Tighten lock nut -2-.
  • Check toe setting meets specification ⇒ Rep. gr. 44 ; Wheel alignment specifications .

Tightening torques

  • ⇒ Rep. gr. 48 ; Exploded view - track rods

Checking full steering lock

The wheel alignment unit is used to determine the full steering lock.

If the value for the full steering lock is outside the permitted tolerances or the steering wheel is not straight, observe the following procedure:

  • Check steering and suspension components for damage and deformation.
  • Check symmetry of track rods.
  • Renew any damaged components.
  • Measure dimension -a- on both track rod ball joints. Adjust track rod ball joints to same dimension.

Important

  • Dimension -a- must be the same on left and right track rod ball joint.
  • Maximum permitted tolerance between left and right is < 2.5 mm.
Volkswagen ID.4. Checking full steering lock
  • When returning steering to centre position, allow steering wheel to settle by rocking it evenly back and forth past centre position a few times.

Preparations for testing

  • Proper toe setting is not possible without wheel runout compensation.
  • Any existing lateral runout of the wheels must be compensated for, otherwise the result will be falsified.
  • The specified toe-in tolerance may already be exceeded by the permitted amount of axial runout at the wheel rims. In such cases it is not possible to set the toe-in correctly without first compensating for the wheel runout.
  • Observe the instructions from the manufacturer of the wheel alignment equipment.