Wheel bearing

In this manual: Wheel bearing
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
8steps
~48min
2/5difficulty
03060901201509066N·mlb·ft
Tightening torque found on this page
Done 0 of 8
  • Assembly overview - wheel bearing assembly, rear-wheel drive
  • Removing and installing wheel bearing housing
  • Loosening and tightening threaded connections of wheel bearings
  • Removing and installing wheel bearing unit, all-wheel drive
  • Removing and installing wheel bearing unit, rear-wheel drive

Assembly overview - wheel bearing assembly, rear-wheel drive

Overview shown for left side of vehicle as an example

Volkswagen ID.4. Assembly overview - wheel bearing assembly, rear-wheel drive
  1. Bush
  2. Bolt
  • Qty. 3
  • Renew after removing
  • M 12 x 1.5 x 45
  • 90 N·m +90º
  1. Washer
  2. Wheel bearing housing
  • Depending on equipment/ version
  • Allocation ⇒ Electronic parts catalogue (ETKA)
  • ⇒ Rep. gr. 40 ; Removing and installing wheel bearing housing
  1. Wheel bearing unit
  2. ⇒ Rep. gr. 40 ; Removing and installing wheel bearing unit
  • Bolt
  • Renew after removing
  • M16 × 1.5 × 70
  • 200 N·m +90º
  1. Bush

Assembly overview - wheel bearing, all-wheel drive

The overview is shown for the left side of the vehicle as an example.

Volkswagen ID.4. Assembly overview - wheel bearing, all-wheel drive
  1. Bush
  2. Bolt
  • Qty. 4
  • Renew after removing
  • M 12 x 1.25 x 45
  • 90 N·m +90º
  1. Wheel bearing housing
  • ⇒ Rep. gr. 40 ; Removing and installing wheel bearing housing
  1. Wheel bearing unit
  • Depending on equipment/ version
  • Allocation ⇒ Electronic parts catalogue (ETKA)
  • ⇒ Rep. gr. 40 ; Removing and installing wheel bearing unit
  1. Bolt
  • Renew after removing
  • M16 × 1.5 × 70
  • 200 N·m +90º
  1. Bush

Removing and installing wheel bearing housing

Special tools and workshop equipment required

  • ball joint puller - 3287A-
  • spreader device - VAS 751 003-

Removing

Front left speed sensor - G47- and front right speed sensor - G45- will henceforth be referred to as "speed sensor".

Front left vehicle level sender - G78- and front right vehicle level sender - G289- will henceforth be referred to as "vehicle level sender".

Removal and installation are described for the left side of vehicle as an example.

Vehicles with bolted wheel bearings

  • Loosen outer threaded connection of wheel bearing ⇒ Rep.

    gr. 40 ; Loosening and tightening threaded connections of wheel bearings .

  • Unscrew outer bolt of wheel bearing threaded connection.

All vehicles (continued)

Vehicles with all-wheel drive

  • Loosen threaded connection of drive shaft ⇒ Running gear, axles, steering; Rep. gr. 40 ; Drive shafts; Loosening and tightening threaded connections of drive shaft
  • Loosen threaded connection of drive shaft.
  • Press drive shaft out of wheel bearing unit ⇒ Running gear, axles, steering; Rep. gr. 40 ; Drive shaft; Removing and installing drive shaft .

All vehicles (continued)

  • Pull off retaining clip -3-, and detach brake hose -4-.
  • Unscrew bolt -2- from wheel bearing housing -7-.
  • Move aside bracket -1- with electrical wires -8-.
  • Disconnect electrical connector -5- on speed sensor -6-.
  • Remove brake disc ⇒ Brake system; Rep. gr. 46 ; Front brake; Removing and installing brake disc .
  • Remove stone deflector for suspension link ⇒ Rep. gr. 40 ; Removing and installing stone deflector for suspension link .
Volkswagen ID.4. Removing and installing wheel bearing housing
  • Unscrew bolts -arrows-, and remove cover plate -1-.
Volkswagen ID.4. Removing and installing wheel bearing housing

Vehicles with vehicle level sender

  • Remove vehicle level sender from suspension link ⇒ Rep.

    gr. 43 ; Removing and installing front vehicle level sender [G78]/[G289] .

All vehicles (continued)

  • Unscrew nuts -3-.
  • Pull suspension link -2- in direction of -arrow A- off swivel joint.
  • Pull wheel bearing housing -1- outwards in direction of -arrow B-.
  • Swing aside wheel bearing housing -1- outwards to relieve tension from suspension link -2-.
Volkswagen ID.4. Removing and installing wheel bearing housing
  • Loosen nut -2- on track rod ball joint -4-, but do not unscrew it completely. Counter-hold on pin using a suitable tool.
Volkswagen ID.4. Removing and installing wheel bearing housing

Important

  • To protect threads, nut -2- must remain screwed onto pin a few turns.

NOTICE

Damage to wheel bearing housing from loosened bushes due to incorrectly applied ball joint puller.

  • Ball joint puller must be supported on bush and not on wheel bearing housing.
  • Use ball joint puller - 3287A- -A- to press track rod ball joint -4- off wheel bearing housing -1-. Unscrew nut -2-.
  • Unscrew nut -3-.
  • Pull out bolt -5-.
Volkswagen ID.4. Removing and installing wheel bearing housing

NOTICE

Risk of damage to the suspension strut -3- if the guide -2- breaks off.

  • Do not twist the suspension strut -3- when loosening.
  • Do not turn the wheel bearing housing -1- against the guide -2-.
  • Insert spreader device - VAS 751 003- -A- into slot of wheel bearing housing -1-.
  • Spread wheel bearing housing -1- using spreader device - VAS 751 003- -A-. Using suitable tools, turn at hexagon -Bof spindle while counter-holding at level surface -C-.
Volkswagen ID.4. Removing and installing wheel bearing housing

NOTICE

Risk of damage to the wheel bearing housing by spreading it too far.

  • Do not spread the wheel bearing housing further than the specified dimension.
  • Spread wheel bearing housing -1- using spreader device - VAS 751 003- -A-.

Important

  • Dimension -a- must be max. 7.8 mm.
  • Do not turn further than end stop of spreader device - VAS 751 003- -A-.
Volkswagen ID.4. Removing and installing wheel bearing housing

Installing

Install in reverse order of removal, observing the following:

Vehicles with vehicle level sender

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 42 ; Assembly overview - wheel bearing
  • ⇒ Rep. gr. 40 ; Assembly overview - suspension link, swivel joint
  • ⇒ Rep. gr. 40 ; Assembly overview - suspension strut
  • ⇒ Rep. gr. 43 ; Assembly overview - front vehicle level senders

Loosening and tightening threaded connections of wheel bearings

Special tools and workshop equipment required

  • 24 mm socket - T10361AID

Removal and installation are described for the left side of vehicle as an example.

Removing

Vehicles with cap for wheel hub

  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • Remove cap for wheel hub.
  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .

All vehicles (continued)

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Press brake pedal.

NOTICE

Risk of damage to wheel bearings from the vehicle's own weight when threaded connections are loosened on wheel end.

  • When threaded connections of wheel bearings have been loosened, the wheel bearings must not be subjected to load.
  • It is not permissible to loosen threaded connections more than 90º when the vehicle is resting on its wheels.
  • Vehicles without bolted wheel bearings must not be moved while standing on their wheels. If a vehicle nevertheless must be moved, observe the following: install outer joint, and tighten it to 120 N·m.
  • With vehicle standing on its wheels, loosen bolt -1- 90º using 24 mm socket - T10361A- .
  • Raise vehicle.
Volkswagen ID.4. Loosening and tightening threaded connections of wheel bearings
  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .

CAUTION

When the bolt is loosened, the plate can disengage from the toothing and start rotating.

Risk of injury to hands.

  • Wear gloves when counterholding.
  • Unscrew bolt -1-.
  • When doing this, press bolt -2- inwards in direction of wheel bearing housing -3-.
  • Remove plate -2-.
Volkswagen ID.4. Loosening and tightening threaded connections of wheel bearings

Installing

Install in reverse order of removal, observing the following:

Important

  • The aid of an additional person is required for the subsequent work steps.

NOTICE

Risk of damage to wheel bearings from vehicle's own weight when threaded connections of wheel bearings are loosened on wheel end.

  • When threaded connections of wheel bearings are pretightened, the wheels must not be in contact with the ground.
  • Press brake pedal.
  • Tighten bolt -1- to specified torque.
  • Lower vehicle onto its wheels.
  • Tighten bolt -1- to turning further angle.
Volkswagen ID.4. Loosening and tightening threaded connections of wheel bearings

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - wheel bearing

Removing and installing wheel bearing unit, all-wheel drive

Removing

Removal and installation are described for the left side of vehicle as an example.

Vehicles with bolted wheel bearings:

  • Loosen outer threaded connection of wheel bearing ⇒ Rep.

    gr. 40 ; Loosening and tightening threaded connections of wheel bearings .

  • Unscrew outer bolt of wheel bearing threaded connection.

All vehicles (continued)

  • Loosen threaded connection of drive shaft ⇒ Running gear, axles, steering; Rep. gr. 40 ; Drive shafts; Loosening and tightening threaded connections of drive shaft .
  • Loosen threaded connection of drive shaft.
  • Press drive shaft out of wheel bearing unit ⇒ Running gear, axles, steering; Rep. gr. 40 ; Drive shaft; Removing and installing drive shaft .
  • Remove brake disc ⇒ Brake system; Rep. gr. 46 ; Front brake; Assembly overview - front brake .
  • Unscrew bolts -2-.
  • Remove wheel bearing unit -3-.
Volkswagen ID.4. Removing and installing wheel bearing unit, all-wheel drive

NOTICE

Contamination and damage to seals from incorrect handling of wheel bearing unit.

  • Only pick up, place down and store wheel bearing unit as shown in illustration.
  • Place wheel bearing unit -2- onto wheel hub -1-.

Important

  • Grab wheel bearing unit only on outside.
Volkswagen ID.4. Removing and installing wheel bearing unit, all-wheel drive

Important

  • When picking up wheel bearing unit, do not grasp on toothing on the inside.

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - wheel bearing, allwheel drive

Removing and installing wheel bearing unit, rear-wheel drive

Special tools and workshop equipment required

  • spreader device - VAS 751 003-

Removing

Removal and installation are described for the left side of vehicle as an example.

Vehicles with bolted wheel bearings:

  • Loosen outer threaded connection of wheel bearing ⇒ Rep.

    gr. 40 ; Loosening and tightening threaded connections of wheel bearings .

  • Unscrew outer bolt of wheel bearing threaded connection.

Vehicles with bolted wheel bearings:

  • Loosen outer threaded connection of wheel bearing ⇒ Rep.

    gr. 40 ; Loosening and tightening threaded connections of wheel bearings .

  • Unscrew outer bolt of wheel bearing threaded connection.

All vehicles (continued)

  • Remove brake disc ⇒ Brake system; Rep. gr. 46 ; Front brake; Assembly overview - front brake .
  • Unscrew nut -3-.
  • Pull bolt -5- out of wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing wheel bearing unit, rear-wheel drive

NOTICE

Risk of damage to the suspension strut -3- if the guide -2- breaks off.

  • Do not twist the suspension strut -3- when loosening.
  • Do not turn the wheel bearing housing -1- against the guide -2-.
  • Insert spreader device - VAS 751 003- -A- into slot of wheel bearing housing -1-.
  • Spread wheel bearing housing -1- using spreader device - VAS 751 003- -A-. While doing this, turn at hexagon -Bof spindle while counterholding at level surface -C- using suitable tools.
Volkswagen ID.4. Removing and installing wheel bearing unit, rear-wheel drive

NOTICE

Risk of damage to the wheel bearing housing by spreading it too far.

  • Do not spread the wheel bearing housing further than the specified dimension.
  • Spread wheel bearing housing -1- using spreader device - VAS 751 003- -A-.

Important

  • Dimension -a- must be max. 7.8 mm.
  • Do not turn further than end stop of spreader device - VAS 751 003- -A-.
  • Pull wheel bearing housing -1- downwards until topmost bolt of wheel bearing unit can be accessed with socket.
Volkswagen ID.4. Removing and installing wheel bearing unit, rear-wheel drive
  • Unscrew bolts -2-.
  • Remove wheel bearing unit -3- from wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing wheel bearing unit, rear-wheel drive

NOTICE

Contamination and damage to seals from incorrect handling of wheel bearing unit.

  • Only pick up, place down and store wheel bearing unit as shown in illustration.
  • Place wheel bearing unit -2- onto wheel hub -1-.

Important

  • Grab wheel bearing unit only on outside.

Important

  • When picking up wheel bearing unit, do not grasp on toothing on the inside.
Volkswagen ID.4. Removing and installing wheel bearing unit, rear-wheel drive

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - wheel bearing assembly, rear-wheel drive