B-pillar
- Assembly overview - B-pillar
- Renewing B-pillar
- Renewing B-pillar reinforcement
Assembly overview - B-pillar
Overview shown for left side of vehicle as an example
- B-pillar
- Subpart
- ⇒ Rep. gr. 51; Renewing B-pillar
- Separating cut
- Parting cut can be combined with others in cases where extent of damage requires multiple cuts.
- Extended repair area
- If B-pillar reinforcement also has to be replaced, extended repair area must also be cut out when cutting out outer B-pillar.
- Bonded area
- Separating cut
- Parting cut can be combined with others in cases where extent of damage requires multiple cuts.
- Separating cut
- Parting cut can be combined with others in cases where extent of damage requires multiple cuts.
- Moulded foam insert
- ⇒ Rep. gr. 00; Moulded foam inserts

Assembly overview - B-pillar reinforcement
Overview shown for left side of vehicle as an example
- B-pillar reinforcement
- ⇒ Rep. gr. 51; Renewing B-pillar reinforcement
- Bonded area

Renewing B-pillar
WARNING
Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.
- Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
- Use an extraction system during work.
NOTICE
If separating cuts are made too deep, underlying reinforcement could be damaged.
- Only make separating cuts with body saw.
- Rewelding of reinforcements is not permitted due to safety reasons.
NOTICE
If welds are positioned too far on outside, strength could be impaired
- RP weld points must be placed as far as possible from outer edge of welding flange.
NOTICE
If adhesive is applied prematurely, bond could be impaired
- New part must be welded in within 90 minutes.
NOTICE
Bonding properties of adhesive may be impaired if adhesive components are not hardened sufficiently.
- After bonding, the vehicle must not be moved and left at room temperature (at least 15ºC) for 8 to 10 hours.
- During this time, the vehicle must be standing on a level surface.
Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1
Removal and installation are described for left side of vehicle as an example.
Removing
- Make parting cut -2-, -3- and -4- in a straight line, as shown in illustration.

- Separate original joint.
- Detach B-pillar -1-.
- Remove any foam residue -1-.

- Remove remaining material.
- Completely remove remaining adhesive.
- Grind bonding surfaces and welding surfaces back to bare metal and clean.
Installing
Replacement parts
- For allocation of moulded foam inserts, see ⇒ Electronic parts catalogue (ETKA)
- For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)
Important
- New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.
- Transfer separating cut -2- to new part -1-, and cut in a straight line.

- Grind welding surfaces and bonding surfaces on new part -1- down to bare metal and clean.
- Prepare moulded foam inserts -1- for installation and insert.

- Apply 2-component body adhesive to entire surface.
- Adapt new part -1- to fit and fix in position.

- Check fit with add-on parts.
- Fix new part in position -1- with mole grips.
- Weld in new part -1-, RP spot weld seam.
- Weld parting cuts (either MIG solder seam or SG stepped weld seam).
- Weld extended repair area -2- if necessary (MIG solder seam or SG stepped weld seam).
Vehicles with type plate.
- Reattach type plate after painting ⇒ p3.1.2 late"
Vehicles with safety certificate.
- Reattach safety certificate after painting ⇒ c3.1.3 ertificate"
Renewing B-pillar reinforcement
WARNING
Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.
- Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
- Use an extraction system during work.
NOTICE
If separating cuts are made too deep, underlying reinforcement could be damaged.
- Only make separating cuts with body saw.
- Rewelding of reinforcements is not permitted due to safety reasons.
NOTICE
If welds are positioned too far on outside, strength could be impaired
- RP weld points must be placed as far as possible from outer edge of welding flange.
NOTICE
If adhesive is applied prematurely, bond could be impaired
- New part must be welded in within 90 minutes.
NOTICE
Bonding properties of adhesive may be impaired if adhesive components are not hardened sufficiently.
- After bonding, the vehicle must not be moved and left at room temperature (at least 15ºC) for 8 to 10 hours.
- During this time, the vehicle must be standing on a level surface.
Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1
Removal and installation are described for left side of vehicle as an example.
Removing
Remove B-pillar including extended repair area ⇒ Rep. gr. 51; Renewing B-pillar.
- Insert mechanical door tensioner.

- Separate original joint.
- Detach inner B-pillar -1-.
- Remove remaining material.

- Completely remove remaining adhesive.
- Grind bonding surfaces and welding surfaces back to bare metal and clean.
Installing
Replacement parts
- For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)
Important
- New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.
- Grind welding surfaces and bonding surfaces on new part -1- down to bare metal and clean.

- In area of roof side member reinforcement, transfer position and number of holes from removed section to new part -1-.
- In area of side member reinforcement, transfer position and number of holes from removed section to new part -1-.
- Drill or alternately punch 8 mm diameter holes for SG plug weld seam.
- Apply 2-component body adhesive to entire surface.

- Adapt new part -1- to fit and fix in position

- Check fit with add-on parts.
- Weld in new part -1-, RP spot weld seam and SG plug weld seam.
- Install B-pillar ⇒ Rep. gr. 51; Renewing B-pillar.
- Check fit with add-on parts.
- Weld in new part -1-, RP spot weld seam and SG plug weld seam.
- Install B-pillar ⇒ Rep. gr. 51; Renewing B-pillar.