Drive shaft

In this manual: Drive shaft
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
4steps
~24min
2/5difficulty
060120180240300200148N·mlb·ft
Tightening torque found on this page
Done 0 of 4
  • Assembly overview - drive shaft
  • Removing and installing drive shaft
  • Loosening and tightening threaded connections of drive shaft
  • Dismantling and assembling drive shaft
  • Tensioning clamp for boot, ID.4, ID.5

Assembly overview - drive shaft

The overview is shown for the left side of the vehicle as an example.

Volkswagen ID.4. Assembly overview - drive shaft
  1. Clamp
  • Renew after removing
  • ⇒ Rep. gr. 42 ; Tensioning clamp for boot
  1. Boot
  2. Clamp
  • Renew after removing
  • ⇒ Rep. gr. 42 ; Tensioning clamp for boot
  1. Outer constant velocity joint
  • ⇒ Rep. gr. 42 ; Dismantling and assembling drive shaft
  1. Bolt
  • Renew after removing
  • ⇒ Rep. gr. 42 ; Loosening and tightening threaded connections of drive shaft
  • M16 × 1.5 × 70
  • 200 N·m +90º
  1. Retaining ring
  • Renew after removing
  1. Drive shaft
  • Depending on equipment/ installation period
  • Allocation ⇒ Electronic parts catalogue (ETKA)
  1. Retaining ring
  • Renew after removing
  1. Clamp
  • Renew after removing
  • ⇒ Rep. gr. 42 ; Tensioning clamp for boot
  1. Boot
  • Renew after removing
  1. Clamp
  • Renew after removing
  • ⇒ Rep. gr. 42 ; Tensioning clamp for boot
  1. Triple roller spider with rollers
  • ⇒ Rep. gr. 42 ; Dismantling and assembling drive shaft
  1. Joint body
  • ⇒ Rep. gr. 42 ; Dismantling and assembling drive shaft
  1. Retaining ring
  • Renew after removing

Removing and installing drive shaft

Special tools and workshop equipment required

  • Cleaning set - VAS 294 017-
  • engine and gearbox jack - VAS 6931-
  • hook - VAS 281 007-
  • pressure tool - T10520A-
  • support - VAS 6931/1-
  • thrust piece - T10520/5-

Rear left vehicle level sender - G76- will henceforth be referred to as "rear vehicle level sender".

Left parking brake motor - V282- and right parking brake motor - V283- are referred to hereafter as parking brake motor.

Rear right speed sensor - G44- and rear left speed sensor - G46- will henceforth referred to as "rear speed sensor".

Removal and installation are described for the left side of vehicle as an example.

Removing

Pressing drive shaft out of wheel bearing unit

  • Loosen threaded connection of drive shaft ⇒ Rep. gr. 42 ; Loosening and tightening threaded connections of drive shaft .
  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • Remove rear centre underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear centre underbody cladding .
  • Insert thrust piece - T10520/5- -1- into pressure tool - T10520A- -2-.
Volkswagen ID.4. Removing and installing drive shaft
  • Secure pressure tool - T10520A- -A- to brake drum -1- using 3 wheel bolts -3-.
Volkswagen ID.4. Removing and installing drive shaft
  • Pull out drive shaft using pressure tool - T10520A- .
  1. Tighten knurled nut -1- hand-tight
  2. Using spanner -3-, turn only bolt -2-, not the pressure tool itself.
    Volkswagen ID.4. Removing and installing drive shaft

Removing drive shaft

  • Press drive shaft out of wheel bearing unit
  • Disconnect electrical connector -2- on parking brake motor -1-.
Volkswagen ID.4. Removing and installing drive shaft
  • Unclip electrical wire -1- from retainer -2- -arrows-.
Volkswagen ID.4. Removing and installing drive shaft
  • Disconnect electrical connector -2- from rear speed sensor -3-.
Volkswagen ID.4. Removing and installing drive shaft
  • Insert support - VAS 6931/1- -B- into engine and gearbox jack - VAS 6931- -A-.
  • Secure support - VAS 6931/1- -B- to brake drum -1- using two wheel bolts -2-.
  • Push wheel bearing housing -1- with engine and gearbox jack - VAS 6931- -B- and support - VAS 6931/1- -B- -Aupwards to take up weight.
Volkswagen ID.4. Removing and installing drive shaft
  • Unscrew nut -3-, and pull out bolt -4- on wheel bearing housing -1-.
  • Unscrew bolt -5- from wheel bearing housing -1-.
  • Unscrew bolt -2- from wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing drive shaft

NOTICE

Risk of damage to the drive shaft if the triple roller spider is pulled out of the joint body.

  • Make sure that the drive shaft is not pulled out of the inner joint.
  • Pull the outer constant velocity joint out of wheel bearing housing.
Volkswagen ID.4. Removing and installing drive shaft
  • Swivel rear brake and wheel bearing housing -1- upwards as far as possible with engine and gearbox jack -A-.
  • Pull drive shaft out of wheel bearing housing.
  • Secure drive shaft -1- to upper suspension link -2- using hook - VAS 281 007- -A-.
Volkswagen ID.4. Removing and installing drive shaft
  • Using assembly lever, push drive shaft -1- out of gearbox -2- -arrow-.
  • Pull drive shaft -1- out of gearbox -2-, and remove it.
Volkswagen ID.4. Removing and installing drive shaft

Installing

Install in reverse order of removal, observing the following:

  • Renew gearbox oil seal ⇒ 1-speed gearbox 0MH, rear; Rep.

    gr. 39 ; Oil seals; Renewing left oil seal or ⇒ 1-speed gearbox 0MH, rear; Rep. gr. 39 ; Oil seals; Renewing right oil seal .

  • Mask off jaws of commercially available water pump pliers -A- with adhesive tape to prevent damage to splines of drive shaft -2-.
  • Position ends of new retaining ring -4- at ends of old retaining ring -1-.
  • Apply water pump pliers -A-, and press old retaining ring -1- out of drive shaft groove -2-.
  • New retaining ring -4- is pressed into drive shaft groove -2- at the same time.
  • Make sure that retaining ring -4- is seated correctly.
Volkswagen ID.4. Removing and installing drive shaft
  • Position drive shaft in a straight line, and push it into gearbox with a "jolt" until drive shaft engages audibly.

Important

  • Hold drive shaft by inner joint when inserting.
  • Remove locking fluid from splines of drive shaft -arrow-.
  • Clean splines of drive shaft -1-.

Important

  • Cleaned areas must be free of lubricant.
Volkswagen ID.4. Removing and installing drive shaft
  • Screw pipe brush - VAS 294 017/1- onto handle -2-.
  • Clean splines in wheel bearing unit -1- using pipe brush - VAS 294 017/1- -2-.
  • Move pipe brush - VAS 294 017/1- -2- in direction of -arrows A-.
  • Turn pipe brush - VAS 294 017/1- -2- in direction of -arrow B- when doing this.
Volkswagen ID.4. Removing and installing drive shaft

Important

  • Pipe brush - VAS 294 017/1- -2- may only be turned in direction of -arrow B-.
  • Repeat procedure with pipe brush - VAS 294 017/2- .

Important

  • Cleaned areas must be free of lubricant.
  • Apply locking fluid centrally to splines of drive shaft -1- all around -arrow-. Allocation ⇒ Electronic parts catalogue (ETKA) .
Volkswagen ID.4. Removing and installing drive shaft
  • ⇒ Rep. gr. 42 ; Raise wheel bearing in unladen position .
  • Carry out wheel alignment ⇒ Rep. gr. 44 ; Wheel alignment .

Tightening torques

  • ⇒ Rep. gr. 42 ; Assembly overview - drive shaft
  • ⇒ Rep. gr. 42 ; Assembly overview - suspension link
  • ⇒ Rep. gr. 42 ; Assembly overview - track rod
  • ⇒ Rep. gr. 42 ; Assembly overview - spring control arm

Loosening and tightening threaded connections of drive shaft

Special tools and workshop equipment required

  • socket - T10361ARemoval

Removal and installation are described for the left side of vehicle as an example.

Removing

Vehicles with cap for wheel hub

  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • Remove cap for wheel hub.
  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .

All vehicles (continued)

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Press brake pedal.

NOTICE

Risk of damage to wheel bearings from the vehicle's own weight when threaded connections are loosened on wheel end.

  • When threaded connections of wheel bearings have been loosened, the wheel bearings must not be subjected to load.
  • It is not permissible to loosen threaded connections more than 90º when the vehicle is resting on its wheels.
  • Vehicles without bolted wheel bearings must not be moved while standing on their wheels. If a vehicle nevertheless must be moved, observe the following: install outer joint, and tighten it to 120 N·m.
Volkswagen ID.4. Loosening and tightening threaded connections of drive shaft
  • Use socket - T10361A- to loosen bolt -1- max. 90º with vehicle standing on its wheels.
  • Raise vehicle.
  • Unscrew bolt -1-.

Installing

Install in reverse order of removal, observing the following:

Important

  • The aid of an additional person is required for the subsequent work steps.

NOTICE

Risk of damage to wheel bearings from vehicle's own weight when threaded connections of wheel bearings are loosened on wheel end.

  • When threaded connections of wheel bearings are pretightened, the wheels must not be in contact with the ground.
Volkswagen ID.4. Loosening and tightening threaded connections of drive shaft
  • Press brake pedal.
  • Tighten bolt -1- to specified torque.
  • Lower vehicle onto its wheels.
  • Tighten bolt -1- to further turning angle.

Tightening torques

  • ⇒ Rep. gr. 42 ; Assembly overview - drive shaft

Dismantling and assembling drive shaft

Dismantling and assembling drive shaft, constant velocity joint

  • Remove drive shaft ⇒ Rep. gr. 42 ; Removing and installing drive shaft .
  • Clamp drive shaft -1- in vice -A- using jaw protectors -B-.
Volkswagen ID.4. Dismantling and assembling drive shaft, constant velocity joint
  • Open clamps -2- and -4- for boot -3-.
  • Push back boot -3- on drive shaft -1-.
  • Remove grease, and clean drive shaft -1-.
Volkswagen ID.4. Dismantling and assembling drive shaft, constant velocity joint
  • Drive constant velocity joint -1- off drive shaft -2- using drift -A-.
  • Make sure to position drift -A- exactly at ball hub -3- of constant velocity joint -1-.
  • In the process, change position of drift -A- along ball hub -3- accordingly.
Volkswagen ID.4. Dismantling and assembling drive shaft, constant velocity joint

Installing

Install in reverse order of removal, observing the following:

  • Clean constant velocity joint and drive shaft -1-.
  • Use commercially available water pump pliers -A-.
  • Mask off jaws of water pump pliers -A- with adhesive tape to prevent damage to splines of drive shaft -1-.
  • Position ends of new retaining ring -2- at ends of old retaining ring -3-.
  • Apply water pump pliers -A-, and press old retaining ring -3- out of drive shaft groove -1-.
  • New retaining ring -2- is pressed into drive shaft groove -1- at the same time.
  • Make sure that retaining ring -2- is seated correctly.
Volkswagen ID.4. Dismantling and assembling drive shaft, constant velocity joint
  • Slide on clamp with smaller diameter.
  • Push boot onto drive shaft.
  • Slide on clamp with larger diameter.
  • Knock constant velocity joint onto drive shaft with plastic hammer until retaining ring engages.
  • Press in half of total amount of grease from repair kit at rear of constant velocity joint.
  • Press remaining amount of grease from repair kit into boot.
  • Push boot with clamp onto constant velocity joint.
  • ⇒ Rep. gr. 42 ; Tensioning clamp for boot .

Dismantling and assembling drive shaft, triple roller joint

Special tools and workshop equipment required

  • assembly tool - T10065/1-
  • assembly tool - T10065/4-
  • press tool - VW409-
  • retaining clip pliers - VAS 5503A-
  • thrust plate - VW401-
  • tube - VW416BID

Removing

  • Clamp drive shaft -1- in vice -A- using jaw protectors -B-.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint
  • Open clamps -2- and -4- for boot -3-.
  • Push back boot -3- on drive shaft -5-.
  • Pull joint body -1- off drive shaft.
  • Remove grease, and clean drive shaft -5-.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint
  • Remove retaining ring -3- using retaining clip pliers - VAS 5503A- -C-.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint
  • Insert thrust plate - VW401- -C- and thrust plate - VW401- -D- into workshop press.
  • Fit assembly tool - T10065/4- -B- to drive shaft -2-.
  • Push assembly tool - T10065/1- -A- with opening over drive shaft -2-.
  • Insert drive shaft -2- with assembly tool - T10065/4- -B- into assembly tool - T10065/1- -A-.
  • Insert drive shaft -2- with assembly tool - T10065/4- -Band assembly tool - T10065/1- -A- between thrust plate - VW401- -C- and thrust plate - VW401- -D-.
  • Push thrust plate - VW401- -C- and thrust plate - VW401- -D- together.
  • Fit drive shaft with assembly tool - T10065/4- -B- and assembly tool - T10065/1- -A- onto thrust plate - VW401- -Cand thrust plate - VW401- -D-.
  • Make sure that triple roller spider -1- is properly seated on assembly tool - T10065/4- -B-.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint
  • Mount press tool - VW409- -E- on drive shaft -2-.
  • Press triple roller spider -1- off drive shaft -2-.
  • Pull boot off drive shaft -2-.
  • Clean drive shaft -2-, joint body and groove for seal.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint

Installing

Install in reverse order of removal, observing the following:

  • Push small clamp for boot onto drive shaft.
  • Push boot onto drive shaft.
  • Clamp drive shaft -1- in vice -A- using jaw protectors -B-.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint
  • Clean triple roller spider -1-.
  • Fit triple roller spider -1- onto drive shaft -2-.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint

Important

  • Chamfer -arrow- on triple roller spider -1- points towards drive shaft -2-.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint
  • Drive triple roller spider -1- onto drive shaft -2- using tube - VW416B- -C-.
  • Drive on triple roller spider -1- as far as stop.
Volkswagen ID.4. Dismantling and assembling drive shaft, triple roller joint
  • Install new retaining ring -3- using retaining clip pliers - VAS 5503A- -C-.
  • Make sure it is seated correctly.
  • Press half of total amount of grease from repair kit into triple roller joint.
  • Slide on clamp with larger diameter.
  • Slide joint body over rollers and hold it there.
  • Press remaining amount of grease from repair kit into back of triple roller joint.
  • Push boot with clamp onto joint body.
  • ⇒ Rep. gr. 42 ; Tensioning clamp for boot .

Tensioning clamp for boot, ID.4, ID.5

Tensioning clamp for boot

Special tools and workshop equipment required

  • clamp tensioner - V.A.G 1682A

NOTICE

Risk of damage caused by insufficiently tensioned clamps.

  • Due to the rigid material of the boot and, consequently, the use of a stainless steel clamp, only the specified clamp tensioner may be used for tensioning.
  • Make sure that clamp tensioner spindle moves smoothly.

    Lubricate with suitable lubricant.

  • If spindle is tight, force required to tighten clamp will not be attained even if specified tightening torque is applied.

    Clean the spindle threads

The procedure of tensioning the boot clamp is described for the outer joint as an example.

Important

  • Boot -3- must be seated properly on joint -2-.
  • Boot -3- must be seated properly on drive shaft.
  • Bring clamp tensioner - V.A.G 1682A- -A- into position.
Volkswagen ID.4. Tensioning clamp for boot, ID.4, ID.5

Important

  • Jaws of clamp tensioner - V.A.G 1682A- -A- must be in corners of boot clamp -1-.
  • Tension boot clamp -1- to specified torque of 25 N·m by turning spindle with torque wrench -B- and clamp tensioner - V.A.G 1682A- .
  • Keep clamp tensioner - V.A.G 1682A- -A- straight.