Rear seats

In this manual: Rear seats
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
4steps
~24min
2/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 4
  • Assembly overview - bench seat/individual seats
  • Assembly overview - rear seat backrest
  • Assembly overview - centre armrest
  • Removing and installing bench seat/individual seats
  • Removing and installing seat pan
  • Removing and installing head restraint guide
  • Removing and installing rear seat backrest
  • Removing and installing back panel trim
  • Removing and installing trim for locking mechanism
  • Removing and installing trim frame for load-through hatch
  • Removing and installing flap for load-through hatch

Assembly overview - bench seat/individual seats

  1. Bench seat
  • Depending on equipment/ version
  • ⇒ Rep. gr. 72 ; Removing and installing bench seat/individual seats
  1. Child seat anchor guide in bench seat
  • Qty. 4
  • ⇒ Rep. gr. 74 ; Removing and installing cover and padding of rear bench seat
  1. Arrester
  • Qty. 2
  1. Grommet
  • Qty. 2
  • Renew after removing
  1. Seat pan
  • ⇒ Rep. gr. 72 ; Removing and installing seat pan
  1. Bolt
  • Qty. 10
  • 8 N·m

Specified torque and tightening sequence

Volkswagen ID.4. Assembly overview - bench seat/individual seats
Volkswagen ID.4. Assembly overview - bench seat/individual seats

Assembly overview - rear seat backrest

The overview is shown for the rear seat backrest (2/3) as an example.

  1. Rear seat backrest
  • ⇒ Rep. gr. 72 ; Removing and installing rear seat backrest
  1. Locking mechanism for rear seat backrest
  • ⇒ Rep. gr. 72 ; Assembly overview - locking mechanism
  • ⇒ Rep. gr. 72 ; Removing and installing locking mechanism for rear seat backrest
  1. Outer head restraint
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint
  1. Rear belt guide
  • Depending on equipment/ version
  • ⇒ Rep. gr. 69 ; Removing and installing rear belt guide
  1. Centre head restraint
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint
  1. Head restraint guide
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint guide
  1. Flap for load-through hatch
  • Depending on equipment/ version
  • ⇒ Rep. gr. 72 ; Removing and installing flap for load-through hatch
  1. Inner pivot pin
  • 13,5 N·m
  1. Locking bar
  • ⇒ Rep. gr. 72 ; Removing and installing rear seat backrest
  1. Bolt
  • 9 N·m
  1. Cover
  • ⇒ Rep. gr. 72 ; Removing and installing rear seat backrest
  1. Centre mount
  2. Centre armrest
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Assembly overview - centre armrest
  • ⇒ Rep. gr. 72 ; Removing and installing centre armrest
  1. Rear centre three-point seat belt
  • Depending on equipment/version
  • ⇒ Rep. gr. 69 ; Removing and installing rear three-point seat belt
  1. Outer support pin
Volkswagen ID.4. Assembly overview - rear seat backrest

Assembly overview - locking mechanism

The overview is shown for the left side of vehicle as an example.

  1. Frame, rear seat backrest
  2. Locking mechanism trim
  • ⇒ Rep. gr. 72 ; Removing and installing locking mechanism trim
  1. Locking mechanism for rear seat backrest
  • ⇒ Rep. gr. 72 ; Removing and installing locking mechanism for rear seat backrest
  1. Bolt
  • qty. 2
  • 23 N·m
Volkswagen ID.4. Assembly overview - locking mechanism

Assembly overview - centre armrest

  1. Centre armrest
  • ⇒ Rep. gr. 72 ; Removing and installing centre armrest
  1. Flap for load-through hatch
  • ⇒ Rep. gr. 72 ; Removing and installing flap for load-through hatch
  1. Stop strip
  • ⇒ Rep. gr. 72 ; Removing and installing trim frame for loadthrough hatch
  1. Trim frame for loadthrough hatch
  • ⇒ Rep. gr. 72 ; Removing and installing trim frame for loadthrough hatch
  1. Flap catch trim
  • Qty. 2
  • ⇒ Rep. gr. 72 ; Removing and installing trim frame for loadthrough hatch
  1. Bolt
  • Self-tapping
  • Qty. 2
  • Renew after removing
  • 12 N·m
  1. Bolt
  • Qty. 2
  • 8 N·m
  1. Intermediate padding
  • ⇒ Rep. gr. 74 ; Removing and installing intermediate padding, backrest with load-through hatch
Volkswagen ID.4. Assembly overview - centre armrest

Removing and installing bench seat/individual seats

Special tools and workshop equipment required

  • removal tool - T40445-

Removing

  • Move front seats to foremost position.
  • Remove child seat anchor guides ⇒ Rep. gr. 74 ; Removing and installing cover and padding of rear bench seat .
  • Push in removal tool - T40445- to stop in area of wire hook -2- between bench seat -1- and bracket.
  • Push removal tool - T40445- upwards and carefully lever bench seat -1- in direction of -arrow A- out of grommet -3-.
  • Repeat procedure on other side -arrow B-.
Volkswagen ID.4. Removing and installing bench seat/individual seats
  • Slightly raise bench seat -1- at front, and push wire frame -2- in direction of -arrow- out of arresters -3-.
  • Disconnect electrical connector.
  • Remove bench seat -1-.
Volkswagen ID.4. Removing and installing bench seat/individual seats

Installing

Install in reverse order of removal, observing the following:

  • Check body aperture -arrow- for deformation.

Note

Slight remaining deformations are permissible.

  • Repair any sheet metal deformations using a plastic hammer.
  • Raise floor covering -2-, and press new grommets -1- into body apertures -arrow- until they engage audibly.
  • Arrange floor covering -2- around grommet taking care not to cover the grommet.
Volkswagen ID.4. Removing and installing bench seat/individual seats
  • Before installing the bench seat, check if the wire frame is aligned properly in the area indicated by -arrows-.
  • If applicable, bend back deformed wire frame until it is properly aligned again.

Note

Make sure that the wire hooks engage properly.

  • Insert bench seat, and firmly press wire hooks into grommets.
Volkswagen ID.4. Removing and installing bench seat/individual seats

Removing and installing seat pan

Removing

  • Remove bench seat ⇒ Rep. gr. 72 ; Removing and installing bench seat/individual seats .
  • Fold floor covering in area of seat pan towards front
  • Unscrew bolts -1- and -3-
  • Remove seat pan -2-.
Volkswagen ID.4. Removing and installing seat pan

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - bench seat/individual seats

Removing and installing head restraint

Removing

  • Release rear seat backrest, and fold it forwards slightly.
  • Press height adjustment release button -2- on head restraint guide -1- in direction of -arrow A-, and hold it there.
  • Move head restraint -3- as far as stop upwards -arrow B-.
Volkswagen ID.4. Removing and installing head restraint
  • Press release button -2- on head restraint guide -1- in direction of -arrow A-, and hold it there.
  • Pull head restraint -3- in direction of -arrow B- out of head restraint guide -1-, and remove it.
Volkswagen ID.4. Removing and installing head restraint

Installing

Install in reverse order of removal.

Removing and installing head restraint guide

Removing

Note

3 commercially available screwdrivers with a blade height of 0.4 mm and a blade width of 8 mm are required for removal.

  • Remove head restraint ⇒ Rep. gr. 72 ; Removing and installing head restraint .
  • Push cover and padding -1- on outer side slightly downwards.

Note

Position 2 screwdrivers next to locking devices so that flat side of screwdriver blade rests against locking device.

  • Insert a screwdriver on each side of head restraint channel -4-, and push it in as far as locking device -3-.
  • Turn both screwdrivers 90º in direction of -arrow B-, and release locking devices -3- in direction of -arrow A-.
  • Using an additional screwdriver, lever head restraint guide -2- off head restraint channel -4
Volkswagen ID.4. Removing and installing head restraint guide

Installing

Install in reverse order of removal.

Removing and installing rear seat backrest

Removing

Removal and installation is described for the rear seat backrest (2/3).

  • Remove rear shelf.

Rear seat backrest (2/3)

  • Remove rear right belt buckle ⇒ Rep. gr. 69 ; Removing and installing rear right belt buckle .
  • Fold down flap for load-through hatch.

All vehicles (continued)

Note

For reasons of clarity, the left rear seat backrest (1/3) is not shown in illustration.

  • Pull cover -1- off centre mount -2-.
Volkswagen ID.4. Removing and installing rear seat backrest
  • Unscrew bolt -2-.
  • Fold locking bar -1- in direction of -arrow A-, detach it from centre mount -arrow B-, and remove it.
Volkswagen ID.4. Removing and installing rear seat backrest
  • Lift out rear seat backrest -2- at inner pivot pin -3- in direction of -arrow A-, and pull it out at outer pivot pins -1- in direction of -arrow B-.
  • Remove rear seat backrest -2-.
Volkswagen ID.4. Removing and installing rear seat backrest

Installing

Install in reverse order of removal, observing the following:

  • Push rear seat backrest -2- in opposite direction of -arrow Bonto outer pivot pin -1-.
  • Position inner pivot pin -3- in centre mount -4-.
Volkswagen ID.4. Removing and installing rear seat backrest

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - rear seat backrest

Removing and installing back panel trim

Special tools and workshop equipment required

  • Hot air blower - V.A.G 1416-

Removing

  • Remove head restraint ⇒ Rep. gr. 72 ; Removing and installing head restraint .
  • Fold rear seat backrest towards front.
  • Using commercially available plastic wedge -A-, release locking devices in direction of -arrow-, and lever off child seat anchor cover in rear seat backrest -1- upwards.
Volkswagen ID.4. Removing and installing back panel trim

Note

The back panel trim is bonded to the backrest frame over its entire surface.

  • Apply heat from hot air blower - V.A.G 1416- to entire surface of back panel trim -1-, and carefully detach back panel trim from backrest frame -2-.
Volkswagen ID.4. Removing and installing back panel trim

Installing

Install in reverse order of removal, observing the following:

  • Apply adhesive -1- ⇒ Electronic parts catalogue (ETKA) onto outer surface of backrest frame -2-.
  • Align back panel trim evenly relative to outer edges of backrest frame -2- and opening for child seat anchor cover in rear seat backrest.
  • As soon as desired position has been found, press on back panel trim firmly.
Volkswagen ID.4. Removing and installing back panel trim

Removing and installing trim for locking mechanism

Removing

  • Remove head restraint ⇒ Rep. gr. 72 ; Removing and installing head restraint .
  • Using a screwdriver, detach upper and side piping strip for cover in area of locking mechanism trim from rear seat backrest.

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Using commercially available plastic wedge, carefully push cover next to locking mechanism trim -2- outwards.
  • Using screwdriver -3-, press locking device -1- in direction of -arrow A-, and hold it there.
  • Repeat procedure on other side.
  • Remove locking mechanism trim -2- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing trim for locking mechanism

Installing

Install in reverse order of removal, observing the following:

Important

  • The rear seat backrest locking mechanism must work

Removing and installing locking mechanism for rear seat backrest

Removing

  • Remove locking mechanism trim ⇒ Rep. gr. 72 ; Removing and installing locking mechanism trim .
  • Using commercially available plastic wedge, push cover (exclusively in area of locking mechanism for rear seat backrest) outwards.
  • Unscrew bolts -2-.
  • Remove locking mechanism for rear seat backrest -1-.
Volkswagen ID.4. Removing and installing locking mechanism for rear seat backrest

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - locking mechanism

Removing and installing trim frame for load-through hatch

Special tools and workshop equipment required

  • hook - T40207-
  • lever - T10039-

Removing

  • Fold down centre armrest, and open flap for load-through hatch.
  • Release locking devices -2- using hook - T40207- -3-.
  • Using commercially available plastic wedge, unclip flap catch trim -1- in direction of -arrow- .
Volkswagen ID.4. Removing and installing trim frame for load-through hatch
  • Using lever - T10039- -3-, lever trim frame for load-through hatch -2- in direction of -arrow A- off rear seat backrest -1-.
  • Start levering off in the upper left corner, and proceed in direction of -arrow B-.
  • Remove trim frame for load-through hatch -2-.
Volkswagen ID.4. Removing and installing trim frame for load-through hatch
  • Push cover and padding of rear seat backrest slightly to one side, and unclip stop strip -1- in direction of -arrow-.
  • Remove stop strip -1-.
Volkswagen ID.4. Removing and installing trim frame for load-through hatch

Installing

Install in reverse order.

Removing and installing flap for load-through hatch

Removing

  • Open flap for load-through hatch -1-.
  • Unscrew bolts -2-.
  • Remove flap for load-through hatch -1-.
Volkswagen ID.4. Removing and installing flap for load-through hatch

Installing

Install in reverse order of removal, observing the following:

  • Fit flap for load-through hatch -1-, and tighten bolts -2- handtight only.
  • Close flap for load-through hatch, and align it.
  • Carefully open flap for load-through hatch -1-, and tighten bolts -2- firmly.
Volkswagen ID.4. Removing and installing flap for load-through hatch

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - centre armrest

Removing and installing centre armrest

Removing

  • Open flap for load-through hatch -2- by approx. 1/3.
  • Unscrew bolts -3-.
  • Remove centre armrest -1-.
Volkswagen ID.4. Removing and installing centre armrest

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - centre armrest