Door components

In this manual: Door components
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
6steps
~36min
2/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 6
  • Assembly overview - door components
  • Assembly overview - assembly carrier
  • Assembly overview - door handle and door lock
  • Removing and installing noise insulation for inner side of outer door panel
  • Removing and installing window regulator motor [V147]/[V148]
  • Removing and installing striker pin
  • Removing and installing exterior door handle [EX6]/[EX7]
  • Dismantling and assembling exterior door handle [EX6]/[EX7]
  • Removing and installing mounting bracket
  • Removing and installing lock unit [VX21]/[VX22]
  • Removing and installing assembly carrier
  • Removing and installing window channel
  • Removing and installing window slot inner seal
  • Removing and installing window slot outer seal
  • Removing and installing cap on door handle
  • Removing and installing operating cable for exterior door handle
  • Removing and installing operating cable for interior door handle

Assembly overview - door components

Overview shown for left side of vehicle as an example

  1. Door
  • ⇒ Rep. gr. 57 ; Removing and installing door
  • ⇒ Rep. gr. 57 ; Adjusting door
  1. Window channel
  • ⇒ Rep. gr. 57 ; Removing and installing window channel
  1. Outer window slot seal
  • ⇒ Rep. gr. 57 ; Removing and installing outer window slot seal
  1. Inner window slot seal
  • ⇒ Rep. gr. 57 ; Removing and installing window slot inner seal
  1. Plug
  2. Damping for outer door panel on inside
  • Self-adhesive
  • Dimensions ⇒ Electronic parts catalogue (ETKA)
  • Qty. 3
  • ⇒ General information - body; Rep. gr. 52 ; General procedures; Removing and installing insulation for inner side of door outer panel
  1. Damping for outer door panel on inside
  • Self-adhesive
  • Dimensions ⇒ Electronic parts catalogue (ETKA)
  • ⇒ General information - body; Rep. gr. 52 ; General procedures; Removing and installing insulation for inner side of door outer panel
  1. Door joint seal
  • Renew after removing
  • ⇒ Rep. gr. 57 ; Removing and installing outer door seal
  1. Plug
  2. Plug
    Volkswagen ID.4. Assembly overview - door components

Assembly overview - assembly carrier

Overview is shown for left side of vehicle as an example

  1. Door subframe
  • ⇒ Rep. gr. 57 ; Removing and installing assembly carrier
  1. Cover
  • Depending on equipment/ installation period
  • Qty. 2
  1. Bolt
  • Qty. 2
  • 8 N·m
  1. Clip
  • Qty. 9
  1. Cover
  • Qty. 2
  1. Driver side window regulator motor - V147- / front passenger side window regulator motor - V148-
  • ⇒ Rep. gr. 57 ; Removing and installing window regulator motor [V147]/[V148]
  1. Bolt
  • Qty. 3
  • 3 N·m
Volkswagen ID.4. Assembly overview - assembly carrier

Assembly overview - door handle and door lock

Overview shown for a left-hand drive vehicle as an example

  1. Bowden cable
  • From lock unit to interior door handle
  • ⇒ Rep. gr. 57 ; Removing and installing Bowden cable for interior door handle
  1. Driver door lock unit - VX21- / front passenger door lock unit - VX22-
  • ⇒ Rep. gr. 57 ; Removing and installing lock unit [VX21]/[VX22]
  1. Bolt
  • Qty. 2
  • 18 N·m
  1. Bowden cable
  • From lock unit to mounting bracket
  • ⇒ Rep. gr. 57 ; Removing and installing Bowden cable for exterior door handle
  1. Bolt
  • 3,5 N·m
  1. Cap
  2. Lock cylinder
  • Installed on driver side only
  • ⇒ Rep. gr. 57 ; Removing and installing lock cylinder
  1. Mounting bracket
  • ⇒ Rep. gr. 57 ; Removing and installing mounting bracket
  1. Carrier
  • Renew after removing
  1. Driver exterior door handle - EX6- / front passenger exterior door handle - EX7-
  • Depending on equipment/version
  • With light for exterior door handle illumination, driver side - L283- / light for exterior door handle illumination, front passenger side - L284-
  • With contact sensor for front left exterior door handle - G605- / contact sensor for front right exterior door handle - G606-
  • ⇒ Rep. gr. 57 ; Removing and installing exterior door handle [EX6]/[EX7]
  • ⇒ Rep. gr. 57 ; Dismantling and assembling exterior door handle [EX6]/[EX7]
  1. Cap on door handle
  • Installed on driver side only
  • ⇒ Rep. gr. 57 ; Removing and installing cap on door handle
  1. Trim
  • Depending on equipment/version
  • Can only be renewed with exterior door handle
Volkswagen ID.4. Assembly overview - door handle and door lock

Removing and installing noise insulation for inner side of outer door panel

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-

Important

  • Instructions and specifications regarding temperature, minimum drying time, removal of adhesive residue and cleaning must be adhered to ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for selfadhesive components .

The noise insulation for inner side of outer door panel will henceforth be referred to as "noise insulation".

Removing

  • Pull noise insulation off outer door panel.

Installing

Install in reverse order of removal, observing the following:

If a new door unit is installed

  • Transfer position and dimensions for bonding surface from removed door.

All vehicles (continued)

  • Remove adhesive residue, and clean bonding surfaces ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .
  • Cut insulation to size, and locate it in on bonding surface.

"Foil-laminated" insulation

  • Pull protective film off adhesive tape.
  • Press noise insulation firmly onto inner side of outer door panel.

All vehicles (continued)

"Bitumen" insulation

Note

The processing temperature for bitumen is 140 ºC.

  • Heat up noise insulation with hot air blower - V.A.G 1416- , and press it firmly onto inner side of outer door panel.

Removing and installing window regulator motor [V147]/[V148]

Driver side window regulator motor - V147- and front passenger side window regulator motor - V148- are referred to hereafter as window regulator motor.

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove front door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Front door trims; Removing and installing front door trim .

CAUTION

Risk of injury to hands and eyes due to glass splinters.

Danger of cutting yourself.

  • Put on safety goggles.
  • Put on protective gloves.

NOTICE

Risk of damage to the door window from sliding down.

The door window may be scratched or partially chipped.

  • Fix the door window in position using commercially available adhesive tape.
  • Secure front door window with commercially available adhesive tape to prevent it from falling down.
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-.
  • Remove window regulator motor -1-.
Volkswagen ID.4. Removing and installing window regulator motor [V147]/[V148]

Installing

Install in reverse order of removal, observing the following:

  • Insert window regulator motor -1- on assembly carrier -2-.

    When doing this, move door window up and down until teeth align.

Volkswagen ID.4. Removing and installing window regulator motor [V147]/[V148]
  • Adapt window regulator motor ⇒ Maintenance ; Booklet ; Window regulator: Checking position .

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - assembly carrier

Removing and installing striker pin

Removal and installation are described for left side of vehicle as an example.

Removing

  • Unscrew bolts -2-.
  • Remove striker pin -1-.
Volkswagen ID.4. Removing and installing striker pin

Installing

Install in reverse order of removal, observing the following:

Important

  • Striker pin must be fitted onto B-pillar with curvature facing inwards.
  • ⇒ Rep. gr. 57 ; Adjust striker pin .

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door

Removing and installing exterior door handle [EX6]/[EX7]

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.

Driver exterior door handle - EX6- and front passenger exterior door handle - EX7- are referred to hereafter as door handle.

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Remove assembly carrier ⇒ Rep. gr. 58 ; Removing and installing assembly carrier

Driver door

Remove lock cylinder ⇒ Rep. gr. 57 ; Removing and installing lock cylinder .

All vehicles (continued)

  • Disconnect electrical connector of driver door lock unit - VX21- / front passenger door lock unit - VX22- .
  • Unscrew bolts -3-, and lower the driver door lock unit - VX21- / front passenger door lock unit - VX22- -1-.

Left side of vehicle:

  • Turn eccentric -2- 180º in direction of -arrow-.

Right side of vehicle:

  • Turn eccentric -2- 180º in opposite direction of -arrow-.
Volkswagen ID.4. Removing and installing exterior door handle [EX6]/[EX7]
  • Press and hold rocker switch -2- through opening.
  • Slide sliding plate -1- to stop in direction of -arrow-.
  • Disconnect electrical connector of door handle.
Volkswagen ID.4. Removing and installing exterior door handle [EX6]/[EX7]
  • Swing out door handle -1- in direction of -arrow-, and remove it.
Volkswagen ID.4. Removing and installing exterior door handle [EX6]/[EX7]

Installing

Install in reverse order of removal, observing the following:

  • Swivel in door handle, and let it engage in mounting bracket
  • Using commercially available Torx "T30" driver, turn eccentric on mounting bracket until it engages audibly in eccentric end position.
  • Perform functional check with the door open.

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door handle and door lock

Dismantling and assembling exterior door handle [EX6]/[EX7]

Special tools and workshop equipment required

  • assembly tool - T10118-
  • commercially available drift
  • commercially available flat-bladed screwdriver
  • commercially available pliers

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.

Driver exterior door handle - EX6- and front passenger exterior door handle - EX7- are referred to hereafter as door handle.

The contact sensor for front left exterior door handle - G605- and contact sensor for front right exterior door handle - G606- will henceforth be referred to as "contact sensor for exterior door handle".

The light for exterior door handle illumination, driver side - L283- and light for exterior door handle illumination, front passenger side - L284- will henceforth be referred to as "light for exterior door handle illumination".

The dismantling and assembling procedures are described for the left door handle as an example.

Dismantling

  • Remove door handle ⇒ Rep. gr. 57 ; Removing and installing exterior door handle [EX6]/[EX7] .
  • Push spring -1- in direction of -arrow A-.
  • Using commercially available flat-bladed screwdriver -2-, turn spring -1- 90º in direction of -arrow B- and detach from mounting.
Volkswagen ID.4. Dismantling and assembling exterior door handle [EX6]/[EX7]

Painting door handle

NOTICE

Malfunction upon ingress of water.

  • Do not remove the contact sensor for exterior door handle.
  • Mask off contact sensor for exterior door handle with tape.

All vehicles (continued)

  • Detach electrical connector for light for exterior door handle illumination and contact sensor for exterior door handle -2- in direction of -arrow A-.
  • Using commercially available drift , drive out pin -3- in direction of -arrow B-, and pull it out.
  • Detach spring -1- from door handle -4-.
Volkswagen ID.4. Dismantling and assembling exterior door handle [EX6]/[EX7]
  • Trim -1- must not be removed.
  • Remove liner -3- from door handle -2-, and remove adhesive residue, if there is any ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for selfadhesive components .
Volkswagen ID.4. Dismantling and assembling exterior door handle [EX6]/[EX7]

Assembling

Assemble in reverse order of dismantling, observing the following:

  • Insert spring -1- into door handle -2-.
  • Insert pin -3- in direction of -arrow A-, and press it on firmly using commercially available pliers .
Volkswagen ID.4. Dismantling and assembling exterior door handle [EX6]/[EX7]
  • Using assembly tool - T10118- -2-, turn spring -1- 90º in direction of -arrow A- until hook is engaged in mounting.
  • Push spring -1- apart in central area -3- in direction of -arrow B-.
Volkswagen ID.4. Dismantling and assembling exterior door handle [EX6]/[EX7]

Removing and installing mounting bracket

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove driver door lock unit - VX21- / front passenger door lock unit - VX22- ⇒ Rep. gr. 57 ; Removing and installing door lock unit [VX21]/[VX22] .
  • Remove driver exterior door handle - EX6- / front passenger exterior door handle - EX7- ⇒ Rep. gr. 57 ; Removing and installing exterior door handle [EX6]/[EX7] .
  • Guide electrical wire out of guides -2-.
  • Push mounting bracket -3- to stop in direction of -arrow A-, and remove it in direction of -arrow B-.
Volkswagen ID.4. Removing and installing mounting bracket
  • Swivel out Bowden cable -4- in direction of -arrow A-.
  • Detach Bowden cable -4- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing mounting bracket

Installing

Install in reverse order of removal, observing the following:

Important

  • Guides and retaining hooks of mounting bracket must engage behind metal tabs of door outer panel.
  • Perform functional check with the door open.

Removing and installing lock unit [VX21]/[VX22]

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace

Driver door lock unit - VX21- and front passenger door lock unit - VX22- are referred to hereafter as door lock.

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove assembly carrier ⇒ Rep. gr. 57 ; Removing and installing assembly carrier .

If door lock in driver door is removed:

  • Remove lock cylinder ⇒ Rep. gr. 57 ; Removing and installing lock cylinder .

All vehicles (continued)

  • Disconnect electrical connector -1-.
  • Unscrew bolts -2-.
  • Remove door lock -3- in direction of -arrow-.
Volkswagen ID.4. Removing and installing lock unit [VX21]/[VX22]

If door lock is renewed:

  • Release Bowden cable for exterior door handle ⇒ Rep. gr. 57 ; Removing and installing Bowden cable for exterior door handle .
  • Release Bowden cable for interior door handle ⇒ Rep. gr. 57 ; Removing and installing Bowden cable for interior door handle .

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

  • Perform functional check with the door open.

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door handle and door lock

Removing and installing assembly carrier

Removal and installation are described for left side of vehicle as an example.

The assembly carrier will henceforth be referred to as "carrier".

Removing

  • Remove front door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Front door trims; Removing and installing front door trim .
  • Lever off caps -2- or pull off adhesive tape from carrier -1- using commercially available plastic wedge.
  • Detach front door window -5- from window regulator ⇒ Rep. gr. 64 ; Removing and installing front door window .
  • Push front door window -5- upwards, and secure it against falling down using commercially available adhesive tape.
  • Disconnect electrical connectors.
  • Unclip electrical wires.
  • Unscrew bolts -3-.
  • Turn clips -6- 90º in direction of -arrow D-, and pull them out slightly.
  • Guide Bowden cable with grommet -4- in direction of -arrow A- out of carrier -1-.
  • Push carrier -1- slightly in direction of -arrow B-.
  • Pull carrier -1- in direction of -arrow C- out of door.
Volkswagen ID.4. Removing and installing assembly carrier

Installing

Install in reverse order of removal, observing the following:

Important

  • Installation sequence of clips must be adhered to.
  • Clips must engage audibly.
  • Make sure to install clips centrally on left and right.
  • Install remaining clips.
  • Carry out functional check before installing door trim.

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door lock

Removing and installing window channel

NOTICE

Risk of damage to window channel from applying excessive force.

The metal insert of the window channel may be bent.

  • Handle window channel with care.

Removal and installation are described for the left vehicle side as an example.

Removing

  • Remove inner window slot seal ⇒ Rep. gr. 57 ; Removing and installing inner window slot seal .
  • Remove outer window slot seal ⇒ Rep. gr. 57 ; Removing and installing outer window slot seal .
  • Remove B-pillar trim on front door ⇒ "3.13.1 Removing and installing B-pillar trim on front door" .
  • Loosen upper clip of fixed front door window ⇒ Rep. gr. 64 ; Removing and installing fixed front door window .
  • Pull off window channel -1- in area -3- in direction of -arrow A-.
  • Pull off window channel -1- in area -4- in direction of -arrow B-.
  • Pull window channel -1- in areas -3- and -4- out of door mountings.
  • Pull off window channel -1- in area -2- in direction of -arrow C-, and remove it
Volkswagen ID.4. Removing and installing window channel

Installing

NOTICE

Uneven fit and poor contact after installing window channel.

Wind noise possible.

  • Ensure that item is seated and comes into contact correctly when aligning and installing.
  • Spray window channel with soapy water to facilitate installation.

Installing

NOTICE

Uneven fit and poor contact after installing window channel.

Wind noise possible.

  • Ensure that item is seated and comes into contact correctly when aligning and installing.
  • Spray window channel with soapy water to facilitate installation.
  • Push window channel -1- in areas -3- and -4- into door mountings.
  • Position window channel -1- in upper area of B-pillar -5-.
  • Install B-pillar trim on front door ⇒ "3.13.1 Removing and installing B-pillar trim on front door" .
  • Align window channel -1- with B-pillar trim on front door.
  • Fit window channel -1- in area -2- in direction of -arrow A-, and press it on evenly starting at B-pillar.
  • Push on window channel -1- in area -6- behind fixed front door window.
  • Engage upper clip of fixed front door window ⇒ Rep. gr. 64 ; Removing and installing fixed front door window .
  • Push on window channel -1- in areas -3- and -4-.
Volkswagen ID.4. Removing and installing window channel

Continue installation in reverse order of removal.

Removing and installing window slot inner seal

Removal and installation are described for left side of vehicle as an example.

Inner window slot seal will henceforth be referred to as "window slot seal".

Removing

  • Remove front door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Front door trims; Removing and installing front door trim .

NOTICE

Risk of damage to the window slot seal due to incorrect removal.

The window slot seal may become bent.

  • Proceed with caution when levering off the window slot seal.
  • Lever window slot seal -1- in direction of -arrow A- evenly off door flange -2-.
Volkswagen ID.4. Removing and installing window slot inner seal

Installing

Install in reverse order of removal, observing the following:

  • Position window slot seal flush against B-pillar.
  • Press window slot seal evenly by hand onto door flange by hand, starting at B-pillar

Removing and installing window slot outer seal

Special tools and workshop equipment required

  • removal wedge set - VAS 895 015-
  • wedge - T10039/1-

Removing

Removal and installation are described for the left side of vehicle as an example.

  • Insert wedge no. 3 -4- from removal wedge set - VAS 895 015- between outer window slot seal -1- and B-pillar trim on front door -2-.

NOTICE

Risk of damage to outer window slot seal due to incorrect removal.

If the metal insert in the outer window slot seal is bent, the window slot seal can no longer be straightened out.

  • Pull off the outer window slot seal evenly, without bending it.
  • Using wedge - T10039/1- -5-, lever outer window slot seal -1- evenly off door flange -3- in direction of -arrow A- starting from outside.
Volkswagen ID.4. Removing and installing window slot outer seal

Installing

Install in reverse order of removal, observing the following:

  • Align outer window slot seal -1- in direction of -arrow Acentrally on door flange -2-, and align it with B-pillar-3-

Important

  • The outer window slot seal -1- must not be installed using impact tools.

NOTICE

Risk of damage to outer window slot seal due to incorrect installation.

If the metal insert in the outer window slot seal is bent, the window slot seal can no longer be straightened out.

  • Push on the outer window slot seal evenly, without bending or distorting it.
Volkswagen ID.4. Removing and installing window slot outer seal
  • Starting at B-pillar -3-, push outer window slot seal -1- evenly by hand in direction of -arrow B- onto door flange -2-.

Removing and installing lock cylinder

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Remove cap from door handle ⇒ Rep. gr. 57 ; Removing and installing cap on door handle .
  • Lever off cap -5-.
  • Unscrew bolt -4- as far as stop.
  • Press in bolt -4- with locking element -3- in direction of -arrow A- until lock cylinder -1- is released.
  • Remove lock cylinder -1- in direction of -arrow B- from mounting bracket -2-.
Volkswagen ID.4. Removing and installing lock cylinder

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door handle and door lock

Removing and installing cap on door handle

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

NOTICE

Risk of damage to component surfaces.

  • Do not turn the flat-bladed screwdriver.
  • Do not make any levering movements with the flat-bladed screwdriver.
  • Carefully push small commercially available flat-bladed screwdriver -3- in direction of -arrow A- into opening on underside of cap -1-.
  • Unclip caps -1- using commercially available flat-bladed screwdriver -3-.
  • Detach cap -1- in direction of -arrow B- from lock cylinder -2-.
Volkswagen ID.4. Removing and installing cap on door handle

Installing

  • Push cap -1- in direction of -arrow A- onto lock cylinder -2-.
  • Push cap -1- in direction of -arrow B- onto driver exterior door handle - EX6- until it can be heard to engage.
Volkswagen ID.4. Removing and installing cap on door handle

Removing and installing operating cable for exterior door handle

Removal and installation are described for left side of vehicle as an example.

The driver door lock unit - VX21- and front passenger door lock unit - VX22- will henceforth be referred to as "door lock".

Removing

  • Remove door lock ⇒ Rep. gr. 57 ; Removing and installing lock unit [VX21]/[VX22] .

Door lock with SAFELOCK

  • Turn Bowden cable -2- 90º in direction of -arrow A-, and remove it from retainer.
  • Swing Bowden cable -2- in direction of -arrow B- until Bowden cable -2- can be guided out of eyelet in door lock -1- in direction of -arrow C-.
Volkswagen ID.4. Removing and installing operating cable for exterior door handle

All vehicles (continued)

Door lock without SAFELOCK

  • Turn Bowden cable -2- 90º in direction of -arrow A-, and remove it from retainer.
  • Swing Bowden cable -2- in direction of -arrow B- until Bowden cable -2- can be guided out of eyelet in door lock -1- in direction of -arrow C-.
Volkswagen ID.4. Removing and installing operating cable for exterior door handle

All vehicles (continued)

Installing

Install in reverse order of removal

Removing and installing operating cable for interior door handle

Driver door lock unit - VX21- and front passenger door lock unit - VX22- are referred to hereafter as door lock.

Bowden cable for interior door handle is referred to hereafter as Bowden cable.

Removing

  • Remove door lock ⇒ Rep. gr. 57 ; Removing and installing lock unit [VX21]/[VX22] .

Door lock with flap for Bowden cable

  • Open flap -2- in direction of -arrow D-.
  • Turn Bowden cable -3- 90º in direction of -arrow A- and swivel out in direction of -arrow B-.
  • Swing Bowden cable -3- until Bowden cable -3- can be guided out of eyelet in door lock -1- in direction of -arrow C-.
  • Guide out Bowden cable -3-.
Volkswagen ID.4. Removing and installing operating cable for interior door handle

All vehicles (continued)

Door lock without flap for Bowden cable

  • Turn Bowden cable -2- 90º in direction of -arrow A- and swivel out in direction of -arrow B-.
  • Swing Bowden cable -2- until Bowden cable -2- can be guided out of eyelet in door lock -1- in direction of -arrow C-.
  • Guide out Bowden cable -2-.
Volkswagen ID.4. Removing and installing operating cable for interior door handle

All vehicles (continued)

Installing

Install in reverse order.