Airbag control unit
Assembly overview airbag control unit
- Nut
- qty. 3
- 9 N·m
- Electrical connectr
- Airbag control unit - J234-
- earthed to body via housing
- ⇒ Rep. gr. 69 ; Removing and installing airbag control unit -J234-

Removing and installing airbag control unit [J234]
Removing and installing airbag control unit [J234], left-hand drive vehicles
Special tools and workshop equipment required
- ratchet ring attachment - VAS 262 015-
The airbag control unit - J234- will henceforth be referred to as "airbag control unit".
Removing
- Disconnect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
Vehicles with tunnel support cover
- Remove tunnel support cover ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel; Removing and installing tunnel support cover .
All vehicles (continued)
- Fold back floor covering in area of airbag control unit.
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Release safety latch -4- in direction of -arrow A-, and open latch -5- in direction of -arrow B-.
- Disconnect electrical connector.
- Unscrew nuts -3-.
- Loosen nut -1- using ratchet ring attachment - VAS 262 015- .
NOTICE
Risk of damage to airbag control unit. Electrical connectors corrode when exposed to moisture.
- After unplugging connectors for control unit, cover them or seal them off to prevent moisture from entering.
![Volkswagen ID.4. Removing and installing airbag control unit [J234], left-hand drive vehicles](/media/volkswagen-id-4/353/images/manuals/353/volkswagen_id_4_airbag_control_unit_212.webp)
- Detach airbag control unit -2- from studs, and remove it towards front passenger side.
Installing
Install in reverse order of removal, observing the following:
- Connect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury.
- Stay as far back as possible from pyrotechnic components when switching on the ignition.
- Switch on ignition.
- Read and clear event memory using ⇒ Vehicle diagnostic tester.
If airbag control unit - J234- has been renewed:
- Perform function "Conclude commissioning" with ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
Continued
Tightening torques
- ⇒ Rep. gr. 69 ; Assembly overview - airbag control unit
Removing and installing airbag control unit J234, right-hand drive vehicles
Special tools and workshop equipment required
- ratchet ring attachment - VAS 262 015-
The airbag control unit - J234- will henceforth be referred to as "airbag control unit".
Removing
- Remove front seats ⇒ Rep. gr. 72 ; Removing and installing front seat .
- Remove front sill panel mouldings ⇒ Rep. gr. 70 ; Removing and installing front sill panel moulding .
- Remove lower A-pillar trims ⇒ Rep. gr. 70 ; Removing and installing lower A-pillar trim .
- Remove tunnel support cover ⇒ Rep. gr. 70 ; Removing and installing tunnel support cover .
- Disconnect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
- Lift up floor covering slightly between front and rear screw connections of front seats.
- Pull floor covering back sufficiently to enable access to airbag control unit.
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Release safety latch -4- in direction of -arrow A-, and open latch -5- in direction of -arrow B-.
- Disconnect electrical connector.
- Unscrew nuts -3-.
- Loosen nut -1- using ratchet ring attachment - VAS 262 015- .
NOTICE
Risk of damage to airbag control unit. Electrical connectors corrode when exposed to moisture.
- After unplugging connectors for control unit, cover them or seal them off to prevent moisture from entering.

- Detach airbag control unit -2- from studs, and remove it towards front passenger side.
Installing
Install in reverse order of removal, observing the following:
- Connect electrical connector until it engages audibly.
- Connect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury.
- Stay as far back as possible from pyrotechnic components when switching on the ignition.
- Switch on ignition.
- Read and clear event memory using ⇒ Vehicle diagnostic tester.
If airbag control unit - J234- has been renewed:
- Perform function "Conclude commissioning" with ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
Continued
Tightening torques
- ⇒ Rep. gr. 69 ; Assembly overview - airbag control unit