Anti-roll bar
In this manual: Anti-roll bar
2steps
~12min
1/5difficulty
Done 0 of 2
- Assembly overview - anti-roll bar
- Removing and installing anti-roll bar
- Removing and installing coupling rod
Assembly overview - anti-roll bar

- Anti-roll bar
- ⇒ Rep. gr. 42 ; Removing and installing anti-roll bar
- Mounting
- Part of anti-roll bar
- Coupling rod
- ⇒ Rep. gr. 42 ; Removing and installing coupling rod
- Subframe
- ⇒ Rep. gr. 42 ; Assembly overview - subframe
- ⇒ Rep. gr. 42 ; Fixing subframe in position
- ⇒ Rep. gr. 42 ; Taking up weight of subframe using scissor-type assembly platform
- ⇒ Rep. gr. 42 ; Removing and installing rear axle
- Upper rear suspension link
- ⇒ Rep. gr. 42 ; Assembly overview - suspension link
- ⇒ Rep. gr. 42 ; Removing and installing upper rear suspension link
- Bolt
- Qty. 2
- Renew after removing
- M 10 x 75
- 50 N·m +180º
- Nut
- Qty. 2
- Renew after removing
- M 10
- Inner drive
- Nut
- Qty. 2
- Renew after removing
- M 10
- 55 N·m
- Bolt
- Qty. 4
- Renew after removing
- M 8 x 30
- 20 N·m +90º
Removing and installing anti-roll bar
Special tools and workshop equipment required
- engine and gearbox jack - VAS 6931-
- gearbox support - T10337-
Removing
- Remove rear underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear underbody cladding .
- Remove skid plate ⇒ General body repairs, exterior; Rep.
gr. 66 ; Underbody cladding; Removing and installing skid plate .
- Fit gearbox support - T10337- -A- to engine and gearbox jack - VAS 6931- -B-.
- Position gearbox support - T10337- -A- on anti-roll bar -1-.
Important
- Mounting of gearbox support - T10337- -A- only contacts anti-roll bar -1-.
- Push anti-roll bar -1- upwards.

- Unscrew nut -6- from coupling rod -1-. Counterhold on multipoint socket head on coupling rod -1- when doing this.
- Pull coupling rod -1- out of anti-roll bar -5-.

- Unscrew bolts -3- and -4- for anti-roll bar -2- on subframe -1-. Hold anti-roll bar in position.
- Detach anti-roll bar -2- from subframe.

Installing
Install in reverse order of removal, observing the following:
Tightening torques
- ⇒ Rep. gr. 42 ; Assembly overview - anti-roll bar
Removing and installing coupling rod
Special tools and workshop equipment required
- engine and gearbox jack - VAS 6931-
- gearbox support - T10337-
Removing
- Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
- Fit gearbox support - T10337- -A- to engine and gearbox jack - VAS 6931- -B-.
- Position gearbox support - T10337- -A- on anti-roll bar -1-.
Important
- Mounting of gearbox support - T10337- -A- only contacts anti-roll bar -1-.
- Push anti-roll bar -1- upwards.

- Unscrew nut -4- from bolt -2- on upper rear suspension link -3-.
- Pull out bolt -2-.
- Unscrew nut -6- on coupling rod -1-. Counterhold on multipoint socket head on coupling rod -1- when doing this.
- Pull coupling rod -1- out of anti-roll bar -5-.

Installing
Install in reverse order of removal, observing the following:
- Tighten threaded connections in unladen position ⇒ Rep.
gr. 42 ; Raising wheel bearing assembly to unladen position .
Tightening torques
- ⇒ Rep. gr. 42 ; Assembly overview - anti-roll bar
Was this page helpful?