Front camera for driver assist systems

In this manual: Front camera for driver assist systems
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~5min read

Calibrating front camera for driver assist systems [R242]

  • Calibrating front camera for driver assist systems R242, dynamic
  • Calibrating front camera for driver assist systems R242, static

Calibrating front camera for driver assist systems R242, dynamic

Preparation

Important

  • Observe ⇒ Rep. gr. 98; Necessity of calibration.
  • There must be no entries in the event memory that would hinder calibration.
  • Check camera field of view.

The following situations can cause the camera function to be impaired by sustained poor visibility of the lane marker lines:

  • Contamination or icing in the camera's field of view.
  • Field of view of the camera is fogged.

Important

  • The camera's field of view must be cleaned manually if there is heavy soiling on the inside of the windscreen in the camera's field of view. To do this, the camera and backlight masking screen must be removed and the windscreen cleaned using cleaning solution ⇒ Electronic parts catalogue (ETKA).
  • Check sensors, holders and fasteners for damage, manipulation and secure fit.

Calibrating

Important

  • ⇒ Vehicle diagnostic tester connected.
  • Carry out function "Calibrate front camera for driver assist systems" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Calibrating front camera for driver assist systems R242, static

Special tools and workshop equipment required

  • Calibration board for lane guard system -VAS 6430/4-
  • Setting device -VAS 6430-

Preparation

Important

  • Observe ⇒ Rep. gr. 98; Necessity of calibration.
  • There must be no entries in the event memory that would hinder calibration.
  • Check camera field of view.

The following situations can cause the camera function to be impaired by sustained poor visibility of the lane marker lines:

  • Contamination or icing in the camera's field of view.
  • Field of view of the camera is fogged.

Important

  • The camera's field of view must be cleaned manually if there is heavy soiling on the inside of the windscreen in the camera's field of view. To do this, the camera and backlight masking screen must be removed and the windscreen cleaned using cleaning solution ⇒ Electronic parts catalogue (ETKA).
  • Observe test prerequisites for wheel alignment ⇒ Running gear, axles, steering; Rep. gr. 44; Wheel alignment; Test prerequisites.
  • Observe preparative measures for wheel alignment with driver assist systems ⇒ Running gear, axles, steering; Rep.

    gr. 44; Wheel alignment; Preparative measures.

  • Check camera, holder and fasteners for damage, manipulation and secure fit.
  • Verify whether there is sufficient space between vehicle and setting device -VAS 6430- before driving vehicle onto wheel alignment platform.

Important

  • Distance between setting device and hub centre points of front wheels must be 1500 mm +- 25 mm.

Note

If there is not enough space, move the vehicle backwards onto the wheel alignment platform as required to make space.

  • Drive vehicle straight onto wheel alignment platform.
  • Turn wheels to straight-ahead position.
  • Install quick-release clamps to front wheels.
  • Install reflectors to quick-release clamps.
  • ⇒ Vehicle diagnostic tester connected. Select programme and follow instructions.
  • Measure ride height -a- at all 4 wheels and note data.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static

Important

  • Setting device must not be moved on alignment beam.
  • The wheel alignment platform must be in the lowermost, levelled position for the next work step.
  • Turn up adjustment device until alignment beam is parallel to centre of wheel alignment sensors on front wheels.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • Position setting device at distance -a- from midpoint of hub of front wheels to beam of setting device.

Important

  • Distance -a- = 1500 mm +-25 mm
  • Use distance measuring unit -1- to measure distance -a- on both sides of vehicle and align setting device.

Important

  • Distance -a- must be same on both sides of vehicle.
  • Fit wheel alignment sensor -1- on setting device and tighten.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static

Important

  • The wheel alignment platform must be in the lowermost, levelled position for the next work step.
  • Measure height value -a- between contact point of setting device and wheel contact point on alignment platform.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static

Non-SUV models:

Height of calibration board -VAS 6430/4-: 1200 mm + height value -a-.

  • Enter value in wheel alignment computer.

Continued

All vehicles (continued) SUV models:

Height of calibration board -VAS 6430/4-: 1400 mm + height value -a-.

  • Enter value in wheel alignment computer.

Continued

All vehicles (continued)

  • Loosen clamping bolt -arrow- and place rod -1- on floor.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • Use crank -1- to set calibration board to specified height -2- indicated by wheel alignment computer and make a note of this.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • When specified height has been reached, move level staff -1- upwards slightly, and secure it with clamping bolt -arrow-.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • Turn setting device in direction of -arrow B- until display on wheel alignment computer is within tolerance. Make sure that neither the calibration board nor the alignment beam are displaced.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • Tighten adjuster screws -2- and -3- slightly and secure setting device to prevent it from rolling away.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • Turn adjuster screw -1- until display on wheel alignment computer is within tolerance.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • Turn spirit level -A- with adjuster screw -1- and spirit level -B- with adjuster screws -2- and -3- until calibration board is horizontal.
Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • Loosen clamping bolt -arrow- and place rod -1- on floor.

Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static
  • Verify specified height -2-.

Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static

Important

  • If specified height deviates, correct it using crank -1-.

  • When specified height has been reached, move level staff -1- upwards slightly, and secure it with clamping bolt -arrow-.

Volkswagen ID.4. Calibrating front camera for driver assist systems R242, static

Calibrating

Important

  • ⇒ Vehicle diagnostic tester connected.

  • Carry out function "Calibrate front camera for driver assist systems" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.