Suspension strut, upper suspension link

In this manual: Suspension strut, upper suspension link
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
31steps
~186min
4/5difficulty
010203040502015N·mlb·ft
Tightening torque found on this page
Done 0 of 31
  • Assembly overview - suspension strut
  • Removing and installing suspension strut
  • Removing and installing spring

Assembly overview - suspension strut

The overview is shown for the left side of the vehicle as an example.

Volkswagen ID.4. Assembly overview - suspension strut
  1. Cover
  2. Bolt
  • Qty. 3
  • Renew after removing
  • M8 x 35
  • 20 N·m +90º
  1. Nut
  • Renew after removing
  • 60 N·m
  1. Guide
  2. Suspension strut mounting
  3. Plate
  4. Bump stop
  • Depending on equipment/ version
  • Allocation ⇒ Electronic parts catalogue (ETKA)
  1. Deep groove ball thrust bearing
  2. Spring
  • Allocation ⇒ Electronic parts catalogue (ETKA)
  • ⇒ Rep. gr. 40 ; Removing and installing spring
  1. Protective sleeve
  2. Spring seat
  3. Protective sleeve
  4. Shock absorbers
  • Depending on equipment/version, with or without front left shock absorber damping adjustment valve - N336- and front right shock absorber damping adjustment valve - N337-
  • Allocation ⇒ Electronic parts catalogue (ETKA)
  • ⇒ Rep. gr. 40 ; Removing and installing suspension strut
  1. Nut
  • Renew after removing
  • M 12 x 1.5
  1. Wheel bearing housing
  • Allocation ⇒ Electronic parts catalogue (ETKA)
  • ⇒ Rep. gr. 40 ; Assembly overview - wheel bearing
  1. Bolt
  • Renew after removing
  • M 12 x 1.5 x 80
  • 70 N·m +180º
  1. Guide

Removing and installing suspension strut

Special tools and workshop equipment required

  • engine and gearbox jack - VAS 6931-
  • spreader device - VAS 751 003-
  • support - VAS 6931/1-
  • suspension strut support clamp - V.A.G 1752/20-
  • suspension strut tensioner - VAS 751 005-

Removing

Front left speed sensor - G47- and front right speed sensor - G45- will henceforth be referred to as "front speed sensor".

Front left vehicle level sender - G78- and front right vehicle level sender - G289- will henceforth be referred to as "front vehicle level sender".

Front left shock absorber damping adjustment valve - N336- and front right shock absorber damping adjustment valve - N337- will henceforth be referred to as "shock absorber damping adjustment valve".

Removal and installation are described for the left side of vehicle as an example.

  • Prepare suspension strut tensioner - VAS 751 005- according to ⇒ operating instructions .
  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .

Vehicles with front vehicle level sender

  • Remove front vehicle level sender from suspension link ⇒ Rep. gr. 43 ; Removing and installing front vehicle level sender [G78]/[G289] .

All vehicles (continued)

  • Unscrew nut of coupling rod from suspension strut ⇒ Rep. gr. 40 ; Removing and installing coupling rod .
  • Pull coupling rod off suspension strut.
  • Unscrew nuts -3-.
  • Pull off suspension link -2- in direction of -arrow A-
  • Pull wheel bearing housing -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing suspension strut
  • Remove wiper motor control unit - J400- ⇒ Electrical system; Rep. gr. 92 ; Windscreen wiper system; Removing and installing windscreen wiper motor [V] .

Vehicles with shock absorber damping adjustment valve

  • Disconnect electrical connector -1- on shock absorber damping adjustment valve -2-.
Volkswagen ID.4. Removing and installing suspension strut

All vehicles (continued)

  • Unscrew nut -3-.
  • Pull bolt -5- out of wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing suspension strut

NOTICE

Risk of damage to the suspension strut -3- if the guide -2- breaks off.

  • Do not twist the suspension strut -3- when loosening.
  • Do not turn the wheel bearing housing -1- against the guide -2-.
  • Insert spreader device - VAS 751 003- -A- into slot of wheel bearing housing -1-.
  • Spread wheel bearing housing -1- using spreader device - VAS 751 003- -A-. While doing this, turn at hexagon -Bof spindle while counterholding at level surface -C- using suitable tools.
Volkswagen ID.4. Removing and installing suspension strut

NOTICE

Risk of damage to the wheel bearing housing by spreading it too far.

  • Do not spread the wheel bearing housing further than the specified dimension.
  • Spread wheel bearing housing -1- using spreader device - VAS 751 003- -A-.

Important

  • Dimension -a- must be max. 7.8 mm.
  • Do not turn further than end stop of spreader device - VAS 751 003- -A-.
Volkswagen ID.4. Removing and installing suspension strut
  • Unscrew bolt -2- from wheel bearing housing -7-.
Volkswagen ID.4. Removing and installing suspension strut
  • Secure support - VAS 6931/1- -A- using two wheel bolts -2-.
  • Place engine and gearbox jack - VAS 6931- -B- under support - VAS 6931/1- -A-.
  • Secure and support wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing suspension strut
  • Remove cap -1-.
  • Unscrew suspension strut mounting bolts -2-
Volkswagen ID.4. Removing and installing suspension strut
  • Lower wheel bearing housing -1- with engine and gearbox jack - VAS 6931- -B- and support - VAS 6931/1- -A- until suspension strut -2- is free.
Volkswagen ID.4. Removing and installing suspension strut
  • Assemble suspension strut tensioner - VAS 751 005- according to ⇒ operating instructions .
  • Place support ring - VAS 751 005/3- -A- on suspension strut -1-.

Important

  • Recesses must be located in guides -arrows-.
  • Lettering "Top/oben" must point upwards.
Volkswagen ID.4. Removing and installing suspension strut
  • Position suspension strut tensioner - VAS 751 005- at suspension strut -1-.
  • Attach hooks -B- of suspension strut tensioner - VAS 751 005- to support ring - VAS 751 005/3- -A-.
Volkswagen ID.4. Removing and installing suspension strut

Important

  • Make sure that hooks -B- of suspension strut tensioner - VAS 751 005- properly engage in support ring - VAS 751 005/3- -A-.
  • Insert pins -arrows- of support plate - VAS 751 005/2- -Cinto suspension strut -1-.

Important

  • Pins -arrows- of support plate - VAS 751 005/2- -C- must be located in guides of suspension strut -1-.
Volkswagen ID.4. Removing and installing suspension strut
  • Position rods -arrows- of support plate - VAS 751 005/2- -Con suspension strut -1-.
Volkswagen ID.4. Removing and installing suspension strut

Important

  • Rods -arrows- of support plate - VAS 751 005/2- -C- must be in contact with suspension strut -1-.
  • Turn spindles of suspension strut tensioner - VAS 751 005- -B- in direction of -arrow- evenly and alternately.
  • Turn spindles of suspension strut tensioner - VAS 751 005- -B- in direction of -arrow- until there is enough space for removal of suspension strut -1-.

Important

  • Procedure must be stopped when there are no more threads on spindle.
  • Spring coils must not be in contact with each other.
Volkswagen ID.4. Removing and installing suspension strut
  • Clamp suspension strut support clamp - V.A.G 1752/20- -Din a vice.
  • Clamp suspension strut -1- in suspension strut support clamp - V.A.G 1752/20- -D-.
  • Measure and note distance between support ring - VAS 751 005/3- -A- and support plate - VAS 751 005/2- -C-.
Volkswagen ID.4. Removing and installing suspension strut

CAUTION

Components are under tension.

Loosening threaded connection may cause injury.

  • Do not loosen nut of piston rod on suspension strut.
  • Turn spindles of suspension strut tensioner - VAS 751 005- -B- in direction of -arrow-.
  • Release tension in suspension strut tensioner - VAS 751 005- -B- in direction of -arrow-.
  • Remove suspension strut tensioner - VAS 751 005- -B-.

Installing

Install in reverse order of removal, observing the following:

  • Adjust distance between support ring - VAS 751 005/3- and support plate - VAS 751 005/2- via spindles according to noted values.
  • The aid of an additional person is required for the subsequent work steps.
  • Guides -3- must be properly seated in body.
  • Tighten bolts -2-.
Volkswagen ID.4. Removing and installing suspension strut

Vehicles with vehicle level sender

  • Perform necessary functions with ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - suspension strut
  • ⇒ Rep. gr. 40 ; Assembly overview - anti-roll bar
  • ⇒ Rep. gr. 40 ; Assembly overview - suspension link, swivel joint
  • ⇒ Brake system; Rep. gr. 46 ; Front brake; Assembly overview - front brake

Removing and installing spring

Special tools and workshop equipment required

  • Ring spanner insert - V.A.G 1332/7-
  • Spring tensioner - V.A.G 1752/1-
  • Torque wrench - V.A.G 1332-
  • shock absorber set - T10001-
  • spring retainer - V.A.G 1752/4-
  • spring tensioner - V.A.G 1752/1-
  • suspension strut support clamp - V.A.G 1752/20-
  • suspension strut support clamp - V.A.G 1752/20-

Removing

  • Remove suspension strut ⇒ Rep. gr. 40 ; Removing and installing suspension strut .
  • Clamp suspension strut support clamp - V.A.G 1752/20- -5- in a vice -6-.
  • Clamp suspension strut -3- in suspension strut support clamp - V.A.G 1752/20- -5-.
  • Assemble spring compressor - V.A.G 1752/1- -1- with spring retainer - V.A.G 1752/4- -2-.
  • Apply spring compressor - V.A.G 1752/1- -1- with spring retainer - V.A.G 1752/4- -2- at spring -4-.
Volkswagen ID.4. Removing and installing spring
  • Make sure that spring -2- is properly seated in spring retainer - V.A.G 1752/4- -4- -arrow-.
Volkswagen ID.4. Removing and installing spring
  • Use spring tensioner - V.A.G 1752/1- -11- to preload spring -8- until suspension strut mounting -6- is completely unloaded.
  • Apply tools from shock absorber set - T10001- .
Volkswagen ID.4. Removing and installing spring
  1. Ratchet - T10001/11-
  2. Extension - T10001/8-
  3. Socket - T10001/5-
  4. Torque wrench
  5. Suspension strut mounting
  6. Deep groove ball thrust bearing
  7. Spring retainers - V.A.G 1752/4-
  8. Spring
  9. Suspension strut support clamp - V.A.G 1752/20-
  10. Suspension strut
  11. Spring tensioner - V.A.G 1752/1-
  • Loosen threaded connection. When doing this, counterhold at piston rod with tools.
  • Unscrew nut.
  • Remove suspension strut mounting -5- and deep groove ball thrust bearing -6-.
  • Remove spring -8-.

Installing

Install in reverse order of removal, observing the following:

Installation position of attachments

  • Insert plate -2- into suspension strut mounting -1- so that plate is located beneath hooks of suspension strut mounting.

Important

  • Guide -arrow- must be seated in recess of plate -2-.
Volkswagen ID.4. Removing and installing spring
  • Press bump stop -1- into suspension strut mounting -2-.

Important

  • Bump stop -1- must rest against suspension strut mounting -2- -arrow-.
Volkswagen ID.4. Removing and installing spring
  • Insert protective sleeve -1- in deep groove ball thrust bearing -2-.

Important

  • Protective sleeve -1- must be properly engaged -arrows-.
Volkswagen ID.4. Removing and installing spring

All vehicles (continued)

  • Insert spring seat -3- into shock absorber -2-.
  • Fit spring -1- with spring tensioner - V.A.G 1752/1- onto spring seat -3- at bottom.
Volkswagen ID.4. Removing and installing spring

Important

  • End of spring coil -arrow B- must be in contact with limit stop -arrow A-.

NOTICE

Noises may occur if the suspension strut mounting is not assembled correctly in relation to the thrust bearing.

  • Observe installation position of suspension strut mounting in relation to deep groove ball thrust bearing when assembling.
  • Fit deep groove ball thrust bearing -2- onto spring -3-.
  • Align suspension strut mounting -1- with thrust bearing -2-.
Volkswagen ID.4. Removing and installing spring

Important

  • Guide of suspension strut mounting -1- must be located in recess -arrow- of deep groove ball thrust bearing -2-.
  • Suspension strut mounting -1- must be folded over collar of deep groove ball thrust bearing -2- all around.
  • Make sure that plate -4- is correctly seated.
  • Tighten nut -4- on piston rod -6-, and counter-hold at piston rod with tool.
Volkswagen ID.4. Removing and installing spring
  1. Extension - T10001/8-
  2. Commercially available ratchet
  3. Torque wrench - V.A.G 1332-
  4. Nut
  5. Suspension strut mounting
  6. Piston rod
  7. Socket - T10001/5-
  8. Ring spanner insert - V.A.G 1332/7-
  • Relieve tension on spring tensioner - V.A.G 1752/1- , and remove it from spring.
  • Remove suspension strut from suspension strut support clamp - V.A.G 1752/20- .

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - suspension strut