Subframe

In this manual: Subframe
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
20steps
~120min
4/5difficulty
03060901201507052N·mlb·ft
Tightening torque found on this page
Done 0 of 20
  • Assembly overview - subframe
  • Removing and installing subframe with steering rack, rear wheel drive
  • Removing and installing subframe with motor, all-wheel drive
  • Fixing subframe in position
  • Preparing scissor-type assembly platform
  • Supporting components in vehicle front end
  • Renewing front motor mounting, all-wheel drive

Assembly overview - subframe

Volkswagen ID.4. Assembly overview - subframe
  1. Bolt
  • Qty. 2
  • Renew after removing
  • M 12 × 1.5 × 80
  • 70 N·m +180º
  1. Bolt
  • Qty. 2
  • Renew after removing
  • M8 × 40
  • 16 N·m +90º
  1. Bracket
  2. Bolt
  • Qty. 4
  • Renew after removing
  • M10 × 35
  • 50 N·m +90º
  1. Cross member
  2. Bracket
  3. Support plate
  4. Bolt
  • Qty. 4
  • Renew after removing
  • M10 × 45
  • 50 N·m +90º
  1. Bolt
  • Qty. 4
  • Renew after removing
  • M 12 × 1.5 × 95
  • 70 N·m +180º
  1. Bolt
  • Qty. 4
  • Renew after removing
  • M 12 × 1.5 × 90
  • 70 N·m +180º
  1. Bolt
  • Qty. 2
  • Renew after removing
  • M 12 × 1.5 × 95
  • 70 N·m +180º
  1. Support plate
  2. Subframe
  • ⇒ Rep. gr. 40 ; Removing and installing subframe with steering rack
  • ⇒ Rep. gr. 40 ; Fixing subframe in position

Removing and installing subframe with steering rack, rear wheel drive

Special tools and workshop equipment required

  • ball joint puller - 3287A-
  • scissor-type assembly platform - VAS 6131B-
  • socket/bit set, 39-piece - VAS 6928-

Removing

Front left vehicle level sender - G78- and front right vehicle level sender - G289- will henceforth be referred to as "front vehicle level sender".

Steering rack and power steering control unit - J500- will henceforth be referred to as "steering rack".

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220; Rep. gr. 93 ; De-energise high-voltage system; De-energising high-voltage system .
  • Detach wheels on front axle ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • Remove front underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing front underbody cladding .
  • Remove front left and front right wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing and installing front wheel housing liner .
  • Remove air intake box of front heater and air conditioning unit ⇒ Heating, air conditioning system; Rep. gr. 87 ; Front heater and air conditioning unit; Removing and installing air intake unit of heater and air conditioning unit .
  • Remove battery tray ⇒ Electrical system; Rep. gr. 27 ; Battery; Removing and installing battery tray .
  • ⇒ Electric motor; Rep. gr. 19 ; Cooling system/coolant; Draining coolant .
  • Remove voltage converter ⇒ Electric drive, rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220; Rep. gr. 93 ; Voltage converter; Removing and installing voltage converter [A19] .
  • Remove heater element (PTC) 3 - Z132- ⇒ Heating, air conditioning system; Rep. gr. 87 ; Coolant circuit; Removing and installing heater element 3 [Z132] .
  • ⇒ Rep. gr. 40 ; Support components in vehicle front end .

Vehicles with air deflector

  • Remove air deflector on left and right ⇒ General body repairs, exterior; Rep. gr. 63 ; Front bumper; Removing and installing air deflector .

All vehicles (continued)

  • Unclip retainer -2- for brake lines -3- on subframe -1-.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive
  • Unscrew bolts -6- for brackets -1-, -2- and -3- from subframe -7-.
  • Pull out inner pin, and lever off retaining clip -5-.
  • Move aside coolant pipe -4- on subframe -7-.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive

For reasons of clarity, the subframe -4- is shown removed in the illustration.

  • Release locking device -3- for cable guide -1- at top of subframe -4-. Push aside electrical wire -2- to do this.
  • Pull off cable guide -1- upwards.
  • Unclip retaining clip -6- for electrical wire -2- from rear cross member -5-.
  • Pull off retaining clip -8-.
  • Release locking element -7-, and pull off cable guide upwards.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive
  • Unscrew bolt -3-.
  • Pull universal joint -1- in direction of -arrow- off steering rack -4-.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive

Left-hand drive vehicles

  • Disconnect electrical connectors -1- and -4- from steering rack -3-.
  • Unclip electrical wire from steering rack.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive

All vehicles (continued)

Right-hand drive vehicles

  • Disconnect electrical connectors -2- and -3- from steering rack -1-.
  • Unclip electrical wire from steering rack.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive

All vehicles (continued)

Vehicles with front vehicle level sender

  • Unbolt front left and front right vehicle level senders from suspension link ⇒ Rep. gr. 43 ; Removing and installing front vehicle level senders [G78]/[G289] .

All vehicles (continued)

  • Detach coupling rods from anti-roll bar on both sides of vehicle, and pull them out of anti-roll bar ⇒ Rep. gr. 40 ; Removing and installing coupling rod .
  • Remove track rod ball joint -4- from wheel bearing housing -1- on both sides of vehicle.
  • Loosen nut -2- on track rod ball joint -4-, but do not unscrew it completely. Counterhold on pin using a suitable tool while doing so.
  • To protect thread, leave nut -2- screwed onto pin a few turns.

NOTICE

Risk of damage to wheel bearing housing! Loosened bushes on wheel bearing housing due to incorrect placement of ball joint puller.

  • Position ball joint puller in such a way that fulcrum of bottom support is on bush and not on wheel bearing housing.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive
  • Use ball joint puller - 3287A- -A- to press track rod ball joint -4- off wheel bearing housing -1-. Unscrew nut -2-.
  • Detach lower suspension link -2- from swivel joint -1- on both sides of vehicle.
  • Unscrew nuts -3-.
  • Pull suspension link -2- in direction of -arrow A- off swivel joint.
  • Pull wheel bearing housing -1- outwards in direction of -arrow B-.
  • Swing aside wheel bearing housing -1- outwards to relieve tension from suspension link -2-.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive
  • Unscrew bolts -arrows- for impact bar -2- from subframe -1-.
  • Use socket/bit set, 39-piece - VAS 6928- to unscrew bolt -4- for strut -3-.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive
  • Unscrew bolts -arrows- for impact bar -2- from subframe -1-.
  • Unscrew bolt -4- for strut -3-.
Volkswagen ID.4. Removing and installing subframe with steering rack, rear wheel drive
  • ⇒ Rep. gr. 40 ; Fix subframe in position .
  • Use scissor-type assembly platform - VAS 6131B- to lower subframe.

Installing

Install in reverse order of removal, observing the following:

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Electric motor; Rep. gr. 93 ; Re-energising high-voltage system; Re-energising high-voltage system .

Vehicles with front vehicle level sender

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - subframe
  • ⇒ Rep. gr. 40 ; Assembly overview - wheel bearing
  • ⇒ Rep. gr. 48 ; Assembly overview - steering rack
  • ⇒ Rep. gr. 48 ; Assembly overview - steering column
  • ⇒ Rep. gr. 40 ; Assembly overview - anti-roll bar
  • ⇒ Rep. gr. 40 ; Assembly overview - suspension link, swivel joint
  • ⇒ Rep. gr. 48 ; Assembly overview - track rods

Removing and installing subframe with motor, all-wheel drive

Special tools and workshop equipment required

  • scissor-type assembly platform - VAS 6131B-
  • socket/bit set, 39-piece - VAS 6928-
  • tensioning strap - T10038-

Removing

Steering rack and power steering control unit - J500- will henceforth be referred to as "steering rack".

Front left vehicle level sender - G78- and front right vehicle level sender - G289- will henceforth be referred to as "front vehicle level sender".

Power and control electronics 2 for electric drive - JX4- will henceforth be referred to as "power and control electronics".

Three-phase current drive 2 - VX97- will henceforth be referred to as "three-phase current drive".

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Electric motor; Rep. gr. 93 ; De-energising high-voltage system; De-energising high-voltage system .
  • Remove wheel housing liners on both sides of vehicle ⇒ General body repairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing and installing front wheel housing liner .
  • Remove air ducts on both sides of vehicle ⇒ General body repairs, exterior; Rep. gr. 63 ; Front bumper; Removing and installing air duct .
  • Remove battery tray ⇒ Electrical system; Rep. gr. 27 ; Battery; Removing and installing battery tray .
  • ⇒ Electric motor; Rep. gr. 19 ; Cooling system/coolant; Draining coolant .
  • Remove PTC heater element 3 - Z132- ⇒ Heating, air conditioning system; Rep. gr. 87 ; Coolant circuit; Removing and installing PTC heater element 3 [Z132], all-wheel drive .
  • Remove drive shafts on both sides of vehicle ⇒ Rep.

    gr. 40 ; Removing and installing drive shaft .

  • Unscrew bolts -3- for vibration isolation strut -2- from lock carrier -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive

Left-hand drive vehicles

  • Unscrew bolt -3-.
  • Detach potential equalisation line -2-.
  • Disconnect electrical connector -4- on power and control electronics -1-.
  • Unclip electrical wire -arrows-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unclip retainer -arrows- for coolant hose -2-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unscrew bolts -2- and -4-.
  • Pull universal joint -1- off steering rack -5-.
  • Pull universal joint -1- off intermediate steering shaft -3-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive

All vehicles (continued)

Right-hand drive vehicles

  • Unscrew bolt -2-.
  • Detach potential equalisation line -3-.
  • Disconnect electrical connector -5- on power and control electronics -1-.
  • Unclip retainer -arrow- for electrical wire -3- from bracket -4-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unclip coolant hose -2- -arrows-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unscrew bolts -4-.
  • Remove bracket -1-.
  • Unscrew bolts -2- and -5-.
  • Pull universal joint -1- off steering rack -4-.
  • Pull universal joint -1- off intermediate steering shaft -3-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive

All vehicles (continued)

  • Pull gearbox breather line -2- off three-phase current drive -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Open hose clip -arrow-.
  • Pull coolant hose -2- off three-phase current drive -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unclip line retainer -2- from subframe -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unscrew bolts -4- for retainer -3- of high-voltage cable -2-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Push locking element -4- in direction of -arrow B-.
  • Open locking bracket -3- in direction of -arrow A-, and pull off high-voltage connector -2-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unscrew bolt -1- on cross piece -2-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Lever cable duct -2- in direction of -arrow- off cross member -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unclip retainer -2- for brake lines -3- at rear right -1- on subframe.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Pull out inner pins -4-, and unclip retaining clip -3-.
  • Detach coolant pipe -2- from cross piece -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Open hose clip -3-.
  • Pull coolant hose -2- off three-phase current drive -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Open retainer -2- for coolant hose -3-.
  • Move aside coolant hose -3-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unscrew bolts -6- from subframe -7-.
  • Pull inner pin out of retaining clip -5-, and lever off retaining clip.
  • Move aside coolant pipe -4- on subframe -7-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Open clip -2- above cross piece -1-.
  • Pull coolant hose -3- off coolant pipe -4-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive

Left-hand drive vehicles

  • Disconnect electrical connectors -1- and -4- from steering rack -3-.
  • Unclip electrical wire from steering rack -3-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive

All vehicles (continued)

Right-hand drive vehicles

  • Disconnect electrical connectors -2- and -3- from steering rack -1-.
  • Unclip electrical wire from steering rack -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive

All vehicles (continued)

  • Unscrew bolts -arrows- for impact bar -2- from subframe -1-.
  • Unscrew bolt -4- for vibration isolation strut -3-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Unscrew bolts -arrows- for impact bar -2- from subframe -1-.
  • Use socket/bit set, 39-piece - VAS 6928- to unscrew bolt -4- for vibration isolation strut -3-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Pull vibration isolation strut -2- on left and right in direction of -arrow A-.
  • Pull vibration isolation strut -2- in direction of -arrow B- past subframe -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • Pull vibration isolation strut -2- in direction of -arrow A-.
  • Pull vibration isolation strut -2- in direction of -arrow B- out of lock carrier -1-.
Volkswagen ID.4. Removing and installing subframe with motor, all-wheel drive
  • ⇒ Rep. gr. 40 ; Support components in vehicle front end .
  • ⇒ Rep. gr. 40 ; Take up weight of subframe using scissortype assembly platform .
  • ⇒ Rep. gr. 40 ; Fix subframe in position .

NOTICE

Risk of lines becoming damaged due to limited space.

  • When lowering, ensure sufficient clearance to refrigerant lines and electrical wiring.
  • Carefully lower subframe and motor 100 mm using scissortype assembly platform - VAS 6131B- .
  • Use a tensioning strap - T10038- to secure subframe and motor to scissor-type assembly platform - VAS 6131B- .
  • Carefully lower subframe and motor further using scissortype assembly platform - VAS 6131B- .

Installing

Install in reverse order of removal, observing the following:

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Electric motor; Rep. gr. 93 ; Re-energising high-voltage system; Re-energising high-voltage system .

Vehicles with front vehicle level sender

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - subframe
  • ⇒ Rep. gr. 48 ; Assembly overview - steering column
  • ⇒ Rep. gr. 40 ; Assembly overview - anti-roll bar
  • ⇒ Rep. gr. 40 ; Assembly overview - suspension link, swivel joint
  • ⇒ Rep. gr. 48 ; Assembly overview - track rods
  • ⇒ Electric motor; Rep. gr. 10 ; Removing and installing electric motor; Assembly overview - electric motor 40.2.19
  • ⇒ General body repairs, exterior; Rep. gr. 63 ; Front bumper; Assembly overview - impact bar

Servicing threads in longitudinal member

Repairing the thread in captive nuts in the longitudinal member is possible only under certain conditions ⇒ Body Repairs; Rep.

gr. 50 .

Fixing subframe in position

Special tools and workshop equipment required

  • stud - T10486/1-
  • ⇒ Rep. gr. 40 ; Take up weight of subframe via scissor-type assembly platform .
  • Unscrew bolts -4-.
  • Unscrew bolts -5-.
  • Remove support plate -3-.
Volkswagen ID.4. Fixing subframe in position
  • Screw threaded pin - T10486/1- -A- into outer hole on left side of subframe -1-.
  • Tighten threaded pin - T10486/1- -A- to 20 N·m.
Volkswagen ID.4. Fixing subframe in position
  • Unscrew bolts -2-.
  • Unscrew bolts -6-.
  • Remove support plate -1-.
Volkswagen ID.4. Fixing subframe in position
  • Screw threaded pin - T10486/1- -A- into outer hole on right side of subframe -1-.
  • Tighten threaded pin - T10486/1- -A- to 20 N·m.
Volkswagen ID.4. Fixing subframe in position
  • Unscrew bolt -2-.
Volkswagen ID.4. Fixing subframe in position
  • Screw in threaded pin - T10486/1- -A-, and tighten it to 20 N·m.
Volkswagen ID.4. Fixing subframe in position
  • Unscrew bolt -3-.
Volkswagen ID.4. Fixing subframe in position
  • Screw in threaded pin - T10486/1- -A-, and tighten it to 20 N·m.
Volkswagen ID.4. Fixing subframe in position

Installing

Install in reverse order of removal, observing the following:

  • Always unscrew only one stud - T10486/1- at a time, and tighten respective bolt.
  • Carry out road test.

Important

  • If steering wheel is found to be off centre during road test, wheel alignment must be performed.

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - subframe

Taking up weight of subframe using scissor-type assembly platform

Special tools and workshop equipment required

  • scissor-type assembly platform - VAS 6131B

Removing

  • ⇒ Rep. gr. 40 ; Prepare scissor-type assembly platform .
  • Position scissor-type assembly platform - VAS 6131B- -Alongitudinally under vehicle, align it, and raise it.
  • Position supports -2- and -4- on subframe -1-.
  • Adjust height of supports -2- and -4-.
  • Raise scissor-type assembly platform - VAS 6131B- -A- further.
  • Align supports -4- with holes of subframe -1-.
  • Align supports -2- with holes of subframe -1-.
  • Tighten bolts for supports -2- and -4- on scissor-type assembly platform - VAS 6131B- -A- to 40 N·m.
  • Align support -3- with cross member at rear of subframe -1-.
  • Align height of supports -2-, -3- and -4-, and bolt them on.
  • Raise scissor-type assembly platform - VAS 6131B- further, and support subframe -1-.
Volkswagen ID.4. Taking up weight of subframe using scissor-type assembly platform

Preparing scissor-type assembly platform

Special tools and workshop equipment required

  • Plate - VAS 6131/10-1-
  • Scissor-type assembly platform - VAS 6131B-
  • Spindle - VAS 6131/10-5-
  • Universal support - VAS 6131/13-2-
  • support set for Audi - VAS 6131/10-
  • support set for Audi - VAS 6131/10-4-
  • support set for Audi - VAS 6131/10-7-

Removing

Prepare supports 1:

  • Assemble supports using the following tools:
  1. Adapter, support set for Audi - VAS 6131/10-7-
  2. Spindle - VAS 6131/10-5-
  3. Support cone, support set for Audi - VAS 6131/10-4-
  4. Plate - VAS 6131/10-1-
  5. Scissor-type assembly platform - VAS 6131B-
  6. M 10 x 25 bolt, support set for Audi - VAS 6131/10-
    Volkswagen ID.4. Preparing scissor-type assembly platform

Prepare support 2:

  • Assemble support using the following tools:
  1. Universal support - VAS 6131/13-2-
  2. Spindle - VAS 6131/10-5-
  3. Support cone, support set for Audi - VAS 6131/10-4-
  4. Plate - VAS 6131/10-1-
  5. Scissor-type assembly platform - VAS 6131B-
  6. M 10 x 25 bolt, support set for Audi - VAS 6131/10-
    Volkswagen ID.4. Preparing scissor-type assembly platform
  • Screw bolts for supports by hand into scissor-type assembly platform - VAS 6131B- -3-. Position scissor-type assembly platform - VAS 6131B- -3- horizontally.
Volkswagen ID.4. Preparing scissor-type assembly platform

Supporting components in vehicle front end

Special tools and workshop equipment required

  • adapter - 10-222A/18-
  • adapter - 10-222A/19-
  • adapter - 10-222A/8-
  • adapter - T10626/1-
  • adapter set - T10626-
  • bracket - T10346/1-
  • hook - 10-222A/20-
  • support - T10626/2-
  • support - T10626/3-
  • support bracket - 10-222A-
  • tensioning belt - T10523-
  • tube - T40091/1-

Removing

The air conditioner compressor - VX81- will henceforth be referred to as "air conditioner compressor".

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220; Rep. gr. 93 ; De-energise high-voltage system; De-energising high-voltage system .
  • Remove air intake box of heater and air conditioning unit ⇒ Heating, air conditioning system; Rep. gr. 87 ; Front heater and air conditioning unit; Removing and installing air intake box of heater and air conditioning unit .
  • Remove cap of towing eye -1-.
Volkswagen ID.4. Supporting components in vehicle front end
  • Screw adapter - T10626/1- -1- in mounting for towing eye in direction of -arrow-.
  • Tighten adapter - T10626/1- -1- in direction of -arrow- via ½ inch mounting for square drive -4- to 20 N·m.
  • Screw support - T10626/2- -2- into adapter - 10-222A/19- -G-.
  • Pull out ball locking pin -3- from support - T10626/2- -2-.
  • Push support - T10626/2- -2- onto adapter - T10626/1- -1-.
  • Selected suitable guide groove in adapter - T10626/1- -1-.
  • Secure support - T10626/2- -2- with ball locking pin -3-.
  • Turn adapter - 10-222A/19- -G- with support - T10626/2- -2- on adapter - T10626/1- -1-, and put it down onto floor.
Volkswagen ID.4. Supporting components in vehicle front end
  • Push adapter - 10-222A/18- -E- and adapter - 10-222A/18- -F- onto support bracket - 10-222A- -B-.

Important

  • Long arm from adapter - 10-222A/18- -E- and adapter - 10-222A/18- -F- points in direction of travel.
Volkswagen ID.4. Supporting components in vehicle front end
  • Mount adapter - 10-222A/8- -A- onto support bracket - 10-222A- -B- on left and right.

Important

  • Side with tool number specification from adapter - 10-222A/8- -A- points inwards.
  • Elongated hole of cross member from support bracket - 10-222A- -B- is located on right-hand side of vehicle.
  • Mount support - T10626/3- -D- on elongated hole of cross member from support bracket - 10-222A- -B- using M10 × 65 bolt from adapter set - T10626- .
  • Place support bracket - 10-222A- -B- with both adapters - 10-222A/8- -A- onto upper wheel housing longitudinal members.
  • Push tube - T40091/1- -C- into support of adapter - 10-222A/19- -G-.
  • Push tube - T40091/1- -C- into support - T10626/3- -D-.
  • Align support bracket.
  • Hand-tighten threaded connections of support bracket.
  • Disconnect electrical connectors -3- from air conditioner compressor -1-.
  • Unclip cable holder -4-.
  • Unscrew bolts -2-.
Volkswagen ID.4. Supporting components in vehicle front end
  • Unscrew bolt for potential equalisation line -4- on air conditioner compressor -1-.
Volkswagen ID.4. Supporting components in vehicle front end
  • Mount bracket - T10346/1- -A- with M6 nut -1- and M6 bolt -2- on air conditioner compressor -3-.
Volkswagen ID.4. Supporting components in vehicle front end
  • Attach spindle from support bracket - 10-222A- -D- to adapter - 10-222A/18- -F-.
  • Engage hook - 10-222A/20- -C- in bracket - T10346/1- -A-.
  • Attach spindle from support bracket - 10-222A- -D- to hook - 10-222A/20- -C-.
  • Guide tensioning strap - T10523- -G- under air conditioner compressor -1-.
  • Preload air conditioner compressor -1- slightly via spindle from support bracket - 10-222A- -D-; do not raise.
  • Lay tensioning strap - T10523- -G- around adapter - 10-222A/18- -E-.
  • Push end of tensioning strap - T10523- -G- into tensioning strap buckle.
  • Preload air conditioner compressor -1- via tensioning belt - T10523- -G-; do not raise.
Volkswagen ID.4. Supporting components in vehicle front end
  • Raise air conditioner compressor -1- evenly with tensioning belt - T10523- -G- and spindle from support bracket - 10-222A- -D- until air conditioner compressor -1- is no longer in contact with subframe -2-.
Volkswagen ID.4. Supporting components in vehicle front end

Installing

Install in reverse order of removal, observing the following:

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Electric motor; Rep. gr. 93 ; Re-energising high-voltage system; Re-energising high-voltage system .

Tightening torques

  • ⇒ Heating, air conditioning system; Rep. gr. 87 ; Air conditioner compressor; Assembly overview - air conditioner compressor

Renewing front motor mounting, all-wheel drive

Removing

  • ⇒ Rep. gr. 10 ; Removing and installing front motor; Removing front motor .
  • Unscrew bolts -arrows-.
  • Remove bracket -1-.
Volkswagen ID.4. Renewing front motor mounting, all-wheel drive
  • Unscrew bolts -2- and -3-.
  • Remove motor carrier -1-.
Volkswagen ID.4. Renewing front motor mounting, all-wheel drive

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - subframe