Radiator, radiator fan

In this manual: Radiator, radiator fan
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
4steps
~24min
2/5difficulty
0102030405021N·mlb·ft
Tightening torque found on this page
Done 0 of 4
  • Assembly overview - radiator/radiator fan
  • Removing and installing radiator module
  • Dismantling and assembling radiator module
  • Removing and installing radiator cowl with radiator fan
  • Removing and installing control motor for radiator roller blind [V711], ID.3
  • Removing and installing control motor for radiator roller blind [V711], ID.4

Assembly overview - radiator/radiator fan

  1. Front air duct
  2. Radiator
  • ⇒ Rep. gr. 19 ; Removing and installing radiator module
  1. Cooler blind
  • ⇒ Rep. gr. 19 ; Dismantling and assembling radiator module
  1. Condenser/gas cooler
  • Depending on equipment/ version
  • ⇒ Heating, air conditioning system; Rep.

    gr. 87 ; Refrigerant circuit; Assembly overview - condenser/gas cooler

  1. Rear air duct
  2. Radiator cowl with radiator fan - VX57-
  • With radiator fan control unit - J293-
  • With radiator fan - V7-
  • ⇒ Rep. gr. 19 ; Assembly overview - radiator cowl and radiator fan
  • ⇒ Rep. gr. 19 ; Removing and installing radiator cowl with radiator fan
  1. Bolt
  • Qty. 2
  • 2 N·m
  1. Control motor for radiator roller blind - V711-
  • ⇒ Rep. gr. 19 ; Removing and installing control motor for radiator roller blind [V711]
Volkswagen ID.4. Assembly overview - radiator/radiator fan

Assembly overview - radiator cowl and radiator fan

Volkswagen ID.4. Assembly overview - radiator cowl and radiator fan
  1. Bolt
  • Qty. 3
  • 6 N·m
  1. Radiator cowl
  • ⇒ Rep. gr. 19 ; Removing and installing radiator cowl with radiator fan
  1. Radiator fan - VX57-
  • With radiator fan control unit - J293-
  • With radiator fan - V7-
  • ⇒ Rep. gr. 19 ; Removing and installing radiator fan VX57

Removing and installing radiator module

Removing

  • Remove front underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing front underbody cladding .
  • Move impact bar into service position ⇒ General body repairs, exterior; Rep. gr. 63 ; Front bumper; Moving bumper carrier to and back from service position .

CAUTION

Risk of injury as the radiator fan(s) may start up automatically.

  • When working in the vicinity of the radiator, keep a safe distance from the radiator fan.
  • Do not reach into the radiator fan when unplugging the electrical connector.
  • Unplug electrical connector for radiator fan - VX57- -arrow-.
Volkswagen ID.4. Removing and installing radiator module
  • ⇒ Rep. gr. 19 ; Drain coolant
Volkswagen ID.4. Removing and installing radiator module
  • Pull out securing clip -arrow- and disconnect coolant hose -1- from radiator (bottom left).
Volkswagen ID.4. Removing and installing radiator module
  • Pull out securing clip -arrow- and disconnect coolant hose from radiator (top right).
  • Disconnect refrigerant lines from condenser/gas cooler ⇒ Heating, air conditioning; Rep. gr. 87 ; Refrigerant circuit; Detaching and attaching refrigerant lines at condenser/gas cooler .
  • Pull catches for radiator mounting (bottom) -arrow- out of retaining plates -1- on both sides and detach retaining plates.
Volkswagen ID.4. Removing and installing radiator module

Important

  • A second person is required for the following steps.
  • Lift radiator module out of radiator mountings.

Installing

Installation is carried out in reverse order; note the following:

  • Connect refrigerant lines to condenser/gas cooler ⇒ Heating, air conditioning; Rep. gr. 87 ; Refrigerant circuit; Detaching and attaching refrigerant lines at condenser/gas cooler .
  • Reset service position of impact bar ⇒ General body repairs, exterior; Rep. gr. 63 ; Front bumper; Moving bumper carrier to and back from service position .

Tightening torques

  • ⇒ Rep. gr. 19 ; Assembly overview - radiators/radiator fans

Dismantling and assembling radiator module

Dismantling radiator module

  • Remove radiator module ⇒ Rep. gr. 19 ; Removing and installing radiator module .
  • Press in retaining tabs -1- for radiator cowl on left and right in direction of -arrow A-.
  • Pull radiator cowl -2- in direction of -arrow B- off radiator.
Volkswagen ID.4. Dismantling and assembling radiator module
  • Disconnect air ducts -1- and -2-. To do this, release fasteners -arrows-.
  • In addition, release bottom fasteners -3-. Pull apart air ducts -1- and -2-.

Important

  • To be able to remove the condenser/gas cooler, the radiator roller blind -2- must first be pulled approx. 15 mm out of the fastener.

NOTICE

Risk of damage to the material shaft of radiator roller blind.

  • Only pull or push on the outer frame of the radiator roller blind.
  • Press in retaining tabs -1- for radiator roller blind -2- on left and right in direction of -arrow A-.
  • Grasp radiator roller blind -2- on outer side, and pull it approx. 15 mm upwards out of fastener in direction of -arrow B-.
Volkswagen ID.4. Dismantling and assembling radiator module
  • Remove condenser/gas cooler -2- by pressing in retaining tabs -1- for condenser/gas cooler on left and right in direction of -arrow A-.
  • Pull condenser/gas cooler -2- upwards off radiator in direction of -arrow B-.
  • Take radiator blind off radiator.
Volkswagen ID.4. Dismantling and assembling radiator module

Assembling radiator module

  • Bring radiator blind -1- into installation position on radiator -2- -arrows-. Do not engage the radiator roller blind yet!
Volkswagen ID.4. Dismantling and assembling radiator module
  • Install condenser/gas cooler -2-, and engage it. Ensure proper engagement by pulling.

NOTICE

Risk of damage to the material shaft of radiator roller blind.

  • Only pull or push on the outer frame of the radiator roller blind.
  • Apply pressure to outside of frame, and press radiator roller blind -1- into fastener.
Volkswagen ID.4. Dismantling and assembling radiator module
  • Position air ducts -1- and -2- on radiator, and engage them with each other -arrows-.
  • Make sure that the lower fastener -3- is securely seated.
Volkswagen ID.4. Dismantling and assembling radiator module
  • Position radiator cowl on radiator, and engage it.
  • Install radiator module ⇒ Rep. gr. 19 ; Removing and installing radiator module .

If the control motor for radiator roller blind - V711- has been renewed:

  • Carry out function "Adapt control motor for radiator roller blind" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

If the control motor for radiator roller blind - V711- has been renewed:

  • Carry out function "Renew control motor for radiator roller blind" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Removing and installing radiator cowl with radiator fan

Removing

  • Move bumper carrier to service position ⇒ General body repairs, exterior; Rep. gr. 63 ; Front bumper; Moving bumper carrier to and back from service position .

CAUTION

Risk of injury as the radiator fan(s) may start up automatically.

  • When working in the vicinity of the radiator, keep a safe distance from the radiator fan.
  • Do not reach into the radiator fan when unplugging the electrical connector.
  • Disconnect electrical connector of radiator fan - VX57- -arrow-.
Volkswagen ID.4. Removing and installing radiator cowl with radiator fan

For reasons of clarity, the following work procedures are shown with the radiator module removed.

  • Press in retaining tabs -1- for radiator cowl -2- on left and right in direction of -arrow A-.
  • Pull radiator cowl -2- upwards off radiator in direction of -arrow B-.
  • Tilt radiator cowl -2-, and remove it upwards.
Volkswagen ID.4. Removing and installing radiator cowl with radiator fan

Installing

Install in reverse order of removal, observing the following:

  • Position radiator cowl on radiator, and engage it.
  • Move bumper carrier back from service position ⇒ General body repairs, exterior; Rep. gr. 63 ; Front bumper; Moving bumper carrier to and back from service position .

Removing and installing radiator fan [VX57]

Removing

  • Remove radiator cowl with radiator fan - VX57- ⇒ Rep. gr. 19 ; Removing and installing radiator cowl with radiator fan .
  • Detach electrical wire -1- from radiator cowl.
  • Unscrew bolts -arrows-.
  • Remove radiator fan - VX57- -2- from radiator cowl.
Volkswagen ID.4. Removing and installing radiator fan [VX57]

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 19 ; Assembly overview - radiator cowl and radiator fan

Removing and installing control motor for radiator roller blind [V711], ID.3

Removing and installing control motor for radiator roller blind [V711]

Removing

The control motor for radiator roller blind - V711- will henceforth be referred to as "control motor".

  • Remove lock carrier ⇒ General body repairs, exterior; Rep. gr. 50 ; Lock carrier; Removing and installing lock carrier .
  • Disconnect electrical connector -2-.
  • Unscrew bolts -arrows-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for radiator roller blind [V711], ID.3

Installing

  • Fit control motor -1- in position. If the drive pin of the control motor does not fit into the material shaft, turn the material shaft slightly.
  • Tighten control motor -arrows-.
  • Connect electrical connector -2
Volkswagen ID.4. Removing and installing control motor for radiator roller blind [V711], ID.3
  • Install lock carrier ⇒ General body repairs, exterior; Rep. gr. 50 ; Lock carrier; Removing and installing lock carrier

If the control motor for radiator roller blind - V711- has been renewed:

  • Carry out function "Renew control motor for radiator roller blind" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 19 ; Assembly overview - radiator, radiator fan

Removing and installing control motor for radiator roller blind [V711], ID.4

Removing and installing control motor for radiator roller blind [V711]

Removing

The control motor for radiator roller blind - V711- will henceforth be referred to as "control motor".

  • Remove lock carrier ⇒ General body repairs, exterior; Rep. gr. 50 ; Lock carrier; Removing and installing lock carrier .
  • Disconnect electrical connector -2-.
  • Unscrew bolts -arrows-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for radiator roller blind [V711]

Installing

  • Fit control motor -1- in position. If the drive pin of the control motor does not fit into the material shaft, turn the material shaft slightly.
  • Tighten control motor -arrows-.
  • Connect electrical connector -2
Volkswagen ID.4. Removing and installing control motor for radiator roller blind [V711]
  • Install lock carrier ⇒ General body repairs, exterior; Rep. gr. 50 ; Lock carrier; Removing and installing lock carrier .

If the control motor for radiator roller blind - V711- has been renewed:

  • Carry out function "Renew control motor for radiator roller blind" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 19 ; Assembly overview - radiator, radiator fan

Removing and installing control motor for radiator roller blind [V711]

Removing

The control motor for radiator roller blind - V711- will henceforth be referred to as "control motor".

The upper bolt of the control motor is unscrewed through the opening in the lock carrier -3-.

  • Disconnect electrical connector -2-.
  • Unscrew bolts -arrows-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for radiator roller blind [V711]

Installing

  • Fit control motor -1- in position. If the drive pin of the control motor does not fit into the material shaft, turn the material shaft slightly.
  • Tighten bolts -arrows-.
  • Connect electrical connector -2-.
Volkswagen ID.4. Removing and installing control motor for radiator roller blind [V711]

If the control motor for radiator roller blind - V711- has been renewed:

  • Carry out function "Renew control motor for radiator roller blind" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 19 ; Assembly overview - radiator, radiator fan