Other controlling and regulating components

In this manual: Other controlling and regulating components
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~5min read
  • Removing and installing external air quality and air humidity sensor G935
  • Removing and installing left vent temperature sender [G150], left-hand drive vehicles
  • Removing and installing left footwell vent temperature sender [G261]
  • Removing and installing heater and air conditioning system control unit [J979]

Removing and installing external air quality and air humidity sensor G935

Removing

  • Remove plenum chamber cover ⇒ General body repairs, exterior; Rep. gr. 50 ; Bulkhead; Removing and installing plenum chamber cover .
  • Unplug electrical connector -3-.
  • Release retaining tab -1-.
  • Detach external air quality and air humidity sensor - G935- -2-.
Volkswagen ID.4.  Removing and installing external air quality and air humidity sensor G935

Installing

Installation is carried out in reverse sequence.

Removing and installing ambient temperature sensor G17

Removing

  • Remove bumper cover ⇒ General body repairs, exterior; Rep. gr. 63 ; Bumper (front); Removing and installing bumper cover .
  • Unclip ambient temperature sensor - G17- -1- with bracket -3-.
  • Unplug electrical connector -2-.
  • Unclip temperature sensor -1- from retainer -3-.
Volkswagen ID.4. Removing and installing ambient temperature sensor G17

Installing

Installation is carried out in reverse sequence.

Removing and installing humidity sender for air conditioning system [G260]

The humidity sender for air conditioning system - G260- and sunlight penetration photosensor - G107- are an integral part of the rain and light sensor - G397- .

  • Removing and installing humidity sender for air conditioning system - G260- ⇒ Electrical system; Rep. gr. 92 ; Windscreen wiper system; Removing and installing rain and light sensor [G397] .

Removing and installing left vent temperature sender [G150], left-hand drive vehicles

Removing

  • Remove fuse box cover ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing dash panel cover on driver side .
  • Disconnect electrical connector -2-.
  • Turn left vent temperature sender - G150- -1- 90º clockwise and pull out.
Volkswagen ID.4. Removing and installing left vent temperature sender [G150], left-hand drive vehicles

Installing

Install in reverse order.

Removing and installing left vent temperature sender [G150], right-hand drive vehicles

Removing

  • Remove glove compartment cover ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment cover .
  • Separate electrical connector -2-.
  • Turn left vent temperature sender - G150- -1- 90º clockwise and pull out.
Volkswagen ID.4. Removing and installing left vent temperature sender [G150], right-hand drive vehicles

Installing

Install in reverse order.

Removing and installing right vent temperature sender [G151], left-hand drive vehicles

Removing

  • Remove glove compartment cover ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment cover .
  • Separate electrical connector -2-.
  • Turn right vent temperature sender - G151- -1- 90º clockwise and pull out.
Volkswagen ID.4. Removing and installing right vent temperature sender [G151], left-hand drive vehicles

Installing

Install in reverse order.

Removing and installing right vent temperature sender [G151], right-hand drive vehicles

Removing

  • Remove dash panel cover on driver side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing dash panel cover on driver side
  • Disconnect electrical connector -2-.
  • Turn right vent temperature sender - G151- -1- 90º clockwise and pull out.
Volkswagen ID.4. Removing and installing right vent temperature sender [G151], right-hand drive vehicles

Installing

Install in reverse order.

Removing and installing left footwell vent temperature sender [G261]

Removing

Left-hand drive vehicles

  • Remove footwell vent on driver side ⇒ Rep. gr. 87 ; Removing and installing footwell vent on driver side .

All vehicles (continued)

Right-hand drive vehicles

  • Remove footwell vent on front passenger side ⇒ Rep.

    gr. 87 ; Removing and installing footwell vent on front passenger side .

All vehicles (continued)

  • Remove left footwell vent temperature sender - G261- -2- using commercially available plastic wedge.
Volkswagen ID.4. Removing and installing left footwell vent temperature sender [G261]

Installing

Install in reverse order.

Removing and installing right footwell vent temperature sender [G262]

Removing

Left-hand drive vehicles

  • Remove glove compartment ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment .

All vehicles (continued)

Right-hand drive vehicles

  • Remove footwell cover on driver side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing footwell cover on driver side .

All vehicles (continued)

  • Disconnect electrical connector -1-.
  • Remove right footwell vent temperature sender - G262- -2- using commercially available plastic wedge.
Volkswagen ID.4. Removing and installing right footwell vent temperature sender [G262]

Installing

  • Install in reverse order of removal.

Removing and installing sensor for interior carbon dioxide concentration [G929]

Removing

  • Remove tunnel support cover ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel; Removing and installing tunnel support cover .
  • Slightly fold back floor covering in front left footwell in area of centre tunnel.

WARNING

Risk of asphyxiation from refrigerant R744 When sensor for interior carbon dioxide concentration is removed, there is a risk of asphyxiation due to carbon dioxide.

  • The doors must always be left open when working in the interior.
  • Release sensor for interior carbon dioxide concentration - G929- -2- using commercially available plastic wedge -A-.
  • Remove sensor for interior carbon dioxide concentration - G929- -2-.
  • Disconnect electrical connector -1-.
Volkswagen ID.4. Removing and installing sensor for interior carbon dioxide concentration [G929]

Installing

Install in reverse order.

Removing and installing heater and air conditioning system control unit [J979]

Removing

If the heater and air conditioning system control unit - J979- is renewed:

  • Carry out function "Renew control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Remove glove compartment cover ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment cover .
  • Disconnect electrical connectors -3-.
  • Release retaining tab -arrow- of bracket -2- using commercially available plastic wedge.
  • Pull out heater and air conditioning system control unit - J979- .
Volkswagen ID.4. Removing and installing heater and air conditioning system control unit [J979]

Installing

  • Install in reverse order of removal.

Removing and installing vehicle interior temperature sensor [G1090]

Removing

Vehicle interior temperature sensor - G1090- is referred to hereafter as temperature sensor.

  • Remove tunnel support cover ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel; Removing and installing tunnel support cover .
  • Disconnect electrical connector -2-.
  • Release temperature sensor -1- at locking devices -4-.
  • Remove temperature sensor -1- from tunnel support cover -3-.
Volkswagen ID.4. Removing and installing vehicle interior temperature sensor [G1090]

Installing

Install in reverse order of removal.

Removing and installing rear vent temperature sender [G174]

Removing

  • Remove centre console cover ⇒ General body repairs, interior; Rep. gr. 68 ; Centre console; Removing and installing centre console cover .
  • Disconnect electrical connector -2-.
  • Turn rear vent temperature sender - G174- -1- in direction of -arrow-, and pull it out of mounting.
Volkswagen ID.4. Removing and installing rear vent temperature sender [G174]

Installing

Install in reverse order of removal