Rear brake

In this manual: Rear brake
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
20steps
~120min
4/5difficulty
0204060801005037N·mlb·ft
Tightening torque found on this page
Done 0 of 20
  • Assembly overview - rear brake, drum brake version
  • Assembly overview - brake shoes
  • Removing and installing brake backplate
  • Removing and installing gasket for brake backplate
  • Removing and installing brake drum
  • Removing and installing brake shoes

Assembly overview - rear brake, drum brake version

The overview is shown for the left side of the vehicle as an example.

  1. Multi-point socket head bolt

Qty. 4 ❑ N.108.626.01 ❑ Renew after removing ❑ M10 x 58 ❑ 50 N·m +180º

  1. Bracket
  2. Wheel bearing housing
  • ⇒ Running gear, axles, steering; Rep. gr. 42; Wheel bearing, trailing arm; Assembly overview - wheel bearing
  1. Gasket
  • ⇒ Rep. gr. 46; Removing and installing gasket for brake backplate
  1. Brake backplate with brake shoes
  • ⇒ Rep. gr. 46; Removing and installing brake backplate
  1. Multi-point socket head bolt
  • Qty. 3
  • M8 x 25
  • 20 N·m +45º
  1. Plug
  2. Brake drum
  • Wear limit ⇒ Rep.

    gr. 00; Test and adjustment values

Volkswagen ID.4. Assembly overview - rear brake, drum brake version
  1. Bolt
  • ⇒ Running gear, axles, steering; Rep. gr. 42; Wheel bearing, trailing arm; Assembly overview - wheel bearing
  1. Torx bolt
  • M6 x 16
  • 8 N·m
  1. Brake hose with banjo union and banjo bolt
  • Ensure correct installation position
  • Banjo bolt on wheel brake cylinder: 45 N·m
  1. Clip
  2. Retainer
  3. Brake line
  • 14 N·m

Assembly overview - brake shoes

The overview is shown for the left side of the vehicle as an example.

Volkswagen ID.4. Assembly overview - brake shoes
  1. Brake carrier
  2. Hold-down pin
  3. Sealing plug
  4. Bolt
  • 10 N·m
  1. Protective cap for bleeder screw
  2. Bleeder valve
  • 10 N·m
  1. Pin
  • For brake hose adjustment
  1. Bolt
  • 8 N·m
  1. Bracket for parking brake motor
  2. Left parking brake motor -V282-/right parking brake motor -V283-
  • ⇒ Rep. gr. 46; Removing and installing parking brake motor [V282]/ [V283]
  1. Lower support
  2. Brake shoe
  • Check thickness of brake linings ⇒ Maintenance; Booklet ; Front and rear brake pads/ linings: Checking thickness
  • Renew on both sides
  • Wear limit ⇒ Rep. gr. 00; Test and adjustment values
  • ⇒ Rep. gr. 46; Removing and installing brake shoes
  1. Retaining clip
  • For locking brake shoe ❑ Qty. 2
  1. Lower return spring
  2. Upper return spring
  3. Automatic adjuster
  • Left-side version with annular groove on coarse adjuster
  • With adjustment screw
  1. Wheel brake cylinder
  • ⇒ Rep. gr. 47; Check wheel brake cylinder for leaks
  • Brake shoe with lever for parking brake
  • Check thickness of brake linings ⇒ Maintenance; Booklet ; Front and rear brake pads/linings: Checking thickness
  • Renew on both sides
  • Wear limit ⇒ Rep. gr. 00; Brake technical data
  • ⇒ Rep. gr. 46; Removing and installing brake shoes

Removing and installing brake backplate

Special tools and workshop equipment required

  • hook -VAS 281 007-

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove wheel bearing unit ⇒ Running gear, axles, steering; Rep. gr. 42; Wheel bearing, trailing arm; Removing and installing wheel bearing unit .
  • Unscrew bolt -5-.
Volkswagen ID.4. Special tools and workshop equipment required
  • Unscrew bolts -2-.
Volkswagen ID.4. Special tools and workshop equipment required
  • Unscrew bolts -arrows-.
Volkswagen ID.4. Special tools and workshop equipment required
  • Detach brake backplate -1- from wheel bearing housing -2-.
  • Secure brake backplate -1- to body -arrow- using hook -VAS 281 007- -2-.
Volkswagen ID.4. Special tools and workshop equipment required

Installing

Install in reverse order of removal, observing the following:

  • Renew gasket for brake backplate ⇒ Running gear, axles, steering; Rep. gr. 42; Wheel bearing, trailing arm; Removing and installing gasket for brake backplate.

Tightening torques

  • ⇒ Brake system; Rep. gr. 46; Rear brake; Assembly overview - rear brake, drum brake
  • ⇒ Brake system; Rep. gr. 46; Rear brake; Assembly overview - brake shoes

Removing and installing gasket for brake backplate

Special tools and workshop equipment required

  • Adhesive strip remover -VAS 6349-
  • guide bolt -T10406-
  • template -T10656-

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove brake backplate ⇒ Brake system; Rep. gr. 46; Rear brake; Removing and installing brake backplate.
  • Remove sealant residue -2- using adhesive strip remover -VAS 6349-.
Volkswagen ID.4. Removing and installing gasket for brake backplate
  • Clean sealing surfaces using commercially available methylated spirits.

Important

  • Cleaned surfaces must be free of greasing and sealing agents.
  • Remove sealant residue -2- using adhesive strip remover.
Volkswagen ID.4. Removing and installing gasket for brake backplate
  • Clean sealing surfaces using commercially available methylated spirits.

Important

  • Cleaned surfaces must be free of greasing and sealing agents.

Installing

Install in reverse order of removal, observing the following:

  • Screw guide pin -T10406- -A- into holes of wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing gasket for brake backplate

Important

  • If gaskets -1- were not fitted at factory, retrofitting must always be carried separately for each axle.
  • Insert gasket -1- into side "L" of template -T10656- -B-
Volkswagen ID.4. Removing and installing gasket for brake backplate

Important

  • Note markings on template -B- for relevant side of vehicle.
  • Pull off protective film.
  • Fit template -B- over guide pins -A- onto wheel bearing housing -1-.
Volkswagen ID.4. Removing and installing gasket for brake backplate
  • Press on gasket in marked areas -arrows-.
  • Remove template -B-.
  • Press on gasket -2- over entire circumference.
Volkswagen ID.4. Removing and installing gasket for brake backplate
  • Pull off protective film -2-.

Removing and installing brake drum

WARNING

Health hazard due to poisonous dust from brake system.

Risk of irreversibly deposited dust particles in the lungs. Risk of respiratory health problems.

  • Do not blow out brake system with compressed air.

Removal and installation are described for the left side of vehicle as an example.

Important

  • Do not operate the brake when the system is open.

Removing

  • ⇒ Running gear, axles, steering; Rep. gr. 44; Wheels, tyres; Removing wheel.
  • Carry out function "Brake service, rear" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
  • Unscrew bolt -2-, and remove brake drum -1-.
Volkswagen ID.4. Removing and installing brake drum

Installing

Install in reverse order of removal, observing the following:

  • Carry out function "Brake service, rear" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Tightening torques

  • ⇒ Rep. gr. 46; Assembly overview - rear brake, drum brake version

Removing and installing brake shoes

Special tools and workshop equipment required

  • Assembly tool -T30114-
  • assembly device -T10635-
  • assembly pliers -T10623-

WARNING

Health hazard due to poisonous dust from brake system.

Risk of irreversibly deposited dust particles in the lungs. Risk of respiratory health problems.

  • Do not blow out brake system with compressed air.

Removal and installation are described for the left side of vehicle as an example.

Important

  • Do not operate brake when system is open.

Removing

  • Remove brake drum ⇒ Rep. gr. 46; Removing and installing brake drum.
  • Turn clip -1-.
Volkswagen ID.4. Removing and installing brake shoes
  • Use assembly tool -T30114- -A- to release and pull out clip -1- in direction of -arrow B-. Press against pin from behind while doing so.
  • Using commercially available water pump pliers -A-, lever brake shoe -1- in direction of -arrow B- out of reaction block -3-.
Volkswagen ID.4. Removing and installing brake shoes
  • Put brake shoe -1- in direction of -arrow C- before reaction block -3-.
  • Unhook lower return spring -2-.
  • Bring clip -1- in position.
Volkswagen ID.4. Removing and installing brake shoes
  • Use assembly tool -T30114- -A- to release and pull out clip -1- in direction of -arrow B-. Press against pin from behind while doing so.

NOTICE

Risk of damage to wheel brake cylinder, boot and automatic adjuster through improper handling.

Any damage will have a negative effect on the function of the automatic adjuster and the brake.

  • Remove both brake shoes.
  • Press together brake shoes -1- and -2- in direction of -arrows A-, and pull in direction of -arrows B-.
Volkswagen ID.4. Removing and installing brake shoes
  • Detach handbrake cable -2- from handbrake lever -1-.
Volkswagen ID.4. Removing and installing brake shoes
  • Lever upper return spring -arrow- out of brake shoe -1- using commercially available screwdriver -A-.
Volkswagen ID.4. Removing and installing brake shoes

Installing

Install in reverse order of removal, observing the following:

CAUTION

Risk of injury from chemical cleaning agents. Chemical cleaning agents can be highly flammable and can cause eye and skin irritation.

  • Wear safety goggles, safety gloves and a respirator mask.
  • Observe safety data sheet and instructions for use of the cleaning agent.
  • Clean brake system.

Important

  • Use only commercially available methylated spirits for cleaning the brake system.

11"- brake system models

  • Grease contact surfaces -arrows A- and -arrows B- with lubricating paste. For allocation, see ⇒ Electronic parts catalogue (ETKA).
Volkswagen ID.4. Removing and installing brake shoes

All vehicles (continued)

13"- brake system models

  • Grease contact surfaces -arrows A- with lubricating paste.

    For allocation, see ⇒ Electronic parts catalogue (ETKA).

Volkswagen ID.4. Removing and installing brake shoes

All vehicles (continued)

  • Attach handbrake cable -2- to handbrake lever -1-.
Volkswagen ID.4. Removing and installing brake shoes
  • Install brake shoe -2- with handbrake lever.
Volkswagen ID.4. Removing and installing brake shoes
  • Use assembly tool -T30114- -A- to insert clip -1-. Press against pin from behind while doing so.
  • Insert upper return spring -2- into brake shoes -3- and -5-.
Volkswagen ID.4. Removing and installing brake shoes
  • Position brake shoe -3- on wheel brake cylinder -1-, swing in direction of -arrow-, and place it in front of reaction block -4-.
  • Attach lower return spring -1-, and lever brake shoe -3- into reaction block -2- using commercially available water pump pliers -2-.
Volkswagen ID.4. Removing and installing brake shoes
  • Use assembly tool -T30114- -A- to insert clip -1-. Press against pin from behind while doing so.
Volkswagen ID.4. Removing and installing brake shoes
  • Turn clips -2- and -4- to horizontal, and align return springs at top -1- and bottom -3- in position.
Volkswagen ID.4. Removing and installing brake shoes
  • Note that the automatic adjuster has a fine mechanism.
Volkswagen ID.4. Removing and installing brake shoes

NOTICE

Risk of damage to automatic adjuster from improper handling.

Deformations can negatively influence the function of the automatic adjuster.

  • Handle components with care.
  • Do not deform components.
  • No adjustment on gear wheel.

Important

  • To ensure that the brake functions optimally, pre-adjustment of the automatic adjuster is required. The automatic adjuster must be free to rotate and it should be possible to install it without applying force.
  • Turn bolt in direction of -arrow A- for "rough adjustment".
  • Push regulator in direction of -arrow B- to activate "fine adjustment".

NOTICE

Malfunction and risk of damage to the rear brake due to incorrect adjustment of the automatic adjuster.

  • The automatic adjuster must be adjusted manually to attain the requisite diameter at the brake shoes.
  • Screw automatic adjuster in or out, in such a way that it sits between both brake shoes with slight pretension thus adjusting the rear brake.
  • Press brake shoes -1- and -2- apart using assembly pliers -T10623- -A-.
Volkswagen ID.4. Removing and installing brake shoes
  • Position automatic adjuster in recesses -arrow B- and -arrow C-.
  • Note installation position of automatic adjuster -1-.
Volkswagen ID.4. Removing and installing brake shoes
  • Thermo clip -arrow A- must point towards brake backplate -3- while threaded side -arrow B- points towards brake shoe -2- with handbrake lever.
  • Shorter guide of threaded side -arrow B- must point towards brake backplate -3-.
  • Fit assembly device -T10635- -A- to wheel hub -1- using enclosed bolts -B-.
Volkswagen ID.4. Removing and installing brake shoes

Important

  • Bolts -B- of assembly device -T10635- -A- must be screwed into through-holes.
  • Using assembly pliers -T10623- -B-, repeatedly push brake shoes -1- and -2- in direction of -arrows- until no adjustment is visible nor audible on automatic adjuster.
Volkswagen ID.4. Removing and installing brake shoes
  • Remove setting tool -T10635- -A-.
  • Install brake drum ⇒ Rep. gr. 46; Removing and installing brake drum.

If the brake shoes have been renewed:

  • Check the brake fluid level ⇒ Maintenance; Booklet .

All vehicles (continued)

  • Check function of brake.
  • Carry out road test.

Tightening torques

  • ⇒ Rep. gr. 46; Assembly overview - rear brake, drum brake version