Packaging critical high-voltage batteries with "Warning" status

In this manual: Packaging critical high-voltage batteries with "Warning" status
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
12steps
~72min
3/5difficulty
Done 0 of 12
  • Packaging critical high-voltage batteries with "Warning" status - module
  • Packaging critical high-voltage batteries with "Warning" status, MEB batteries

Packaging critical high-voltage batteries with "Warning" status - module

Packaging overview

Observe general information about packaging high-voltage batteries ⇒ "3.2.1 General information about packaging high-voltage batteries"

Packaging critical high-voltage batteries with "Warning" status - module

WARNING

Risk to health due to dust from expanded glass granules.

Risk of irreversible dust deposits in lungs, which could lead to respiratory problems.

  • Wear a dust protection mask.

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

Removing

  • ⇒ "3.1.2 Classification of high-voltage batteries with aid of ODIS"

Preparing transport container

For the consignment of classified high-voltage batteries with "WARNING" status, special transport containers are required and the currently applicable transport laws apply.

  • Determine suitable transport container using ⇒ "3.3.1 Packaging overview"

Packaging high-voltage battery

Packaging is described for left side of vehicle as an example.

For information about packaging in L container and LP container, see ⇒ "3.3.3 Packaging critical high-voltage batteries with "Warning" status, MEB batteries"

  • Secure all contacts of battery modules to prevent short circuit.
  • Seal all openings for service fluids apart from electrolyte.
  • Remove deposits of hazardous materials and electrolyte from outside of battery module.
  • Package module air-tight with suitable packaging material, e.g. plastic bag and adhesive tape.
  • Open fasteners of transport container.
  • Remove lid of transport container.
  • Remove bag with hollow glass granulate.
  • Check seal -1- on pressure relief valves -2- for damage.
Volkswagen ID.4. Packaging critical high-voltage batteries with
  • Pour hollow glass granulate into transport container up to a layer thickness of at least 200 mm.
Volkswagen ID.4. Packaging critical high-voltage batteries with

Important

  • Multiple modules must be placed upright.
  • Distance -a- between inner walls and modules must be at least 120 mm.
  • Distance between modules must be at least 200 mm.
  • Distance between module and upper edge of transport container must be at least 200 mm.
  • Place module in transport container.
Volkswagen ID.4. Packaging critical high-voltage batteries with
  • Pour in hollow glass granulate so that gaps are filled and also entire transport container up to upper edge.
  • Check circumferential rubber seal for damage.
  • Fit cover on transport container.

Note

If it proves difficult to close the cover, turn the cover 180º if necessary.

  • Seal the cover all around using the fasteners, and retension the fasteners if necessary.
  • Fill in and insert transport documents.
  • Apply the warning notice for hazardous materials and information label to both ends of the transport container.
Volkswagen ID.4. Packaging critical high-voltage batteries with
  • "Dangerous goods class 9"
  • "UN number 3480"
  • "Attention! Damaged lithium-ion battery"
  • "This side up"
  1. "Protect against water"
  2. "Attention! Fragile"
  3. "This side up"
  4. "Maximum stacking load"
  5. "Hazardous material label: Hazardous material category 9 "Various hazardous substances and items" packaging group 2"
  6. "Type label with UN number UN 3480 for lithium-ion batteries"
    Volkswagen ID.4. Packaging critical high-voltage batteries with

Packaging critical high-voltage batteries with "Warning" status, MEB batteries

WARNING

Risk to health due to dust from expanded glass granules.

Risk of irreversible dust deposits in lungs, which could lead to respiratory problems.

  • Wear a dust protection mask.

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Suitable personal protective equipment (PPE) must be worn for the following work.
  • The following steps require a second suitably qualified person to be present to supervise.
  • Outside the danger zone, the second person may assist the high-voltage expert where required to the extent of his/her qualification.
  • The personal protective equipment (PPE) must be dry and undamaged.

⇒ "3.1.2 Classification of high-voltage batteries with aid of ODIS"

Preparing transport container

For the consignment of classified high-voltage batteries with "WARNING" status, special transport containers are required and the currently applicable transport laws apply.

  • Determine suitable transport container using ⇒ "3.3.1 Packaging overview"

Packaging high-voltage batteries in LP container

  • Secure all contacts of high-voltage battery to prevent short circuit.
  • Seal all openings for service fluids apart from electrolyte.
  • Remove deposits of hazardous materials and electrolyte from outside of high-voltage battery.
  • Release cover of transport container and lift off.
  • Place cover down on suitable surface.
  • Remove bag with hollow glass granulate.
  • Check circumferential seal and pressure relief valves of transport container for damage.
  • Pour hollow glass granulate into transport container up to a layer thickness of at least 120 mm.

Support high-voltage battery as described in ⇒ "3.2.2 Packaging high-voltage batteries in genuine part crate"

Important

  • Distance -b- between inner walls and high-voltage battery -1- must be at least 20 mm.
  • Distance -a- between vents -3- and high-voltage battery -1- must be at least 50 mm.
  • Distance between high-voltage battery -1- and upper edge of transport container must be at least 200 mm.
  • Place high-voltage battery -1- centrally in transport container -2-.
Volkswagen ID.4. Packaging critical high-voltage batteries with
  • Pour in hollow glass granulate so that gaps are filled and also entire transport container up to upper edge.
  • Remove hollow glass granulate from circumferential seal of transport container.
  • Fit cover on transport container.
  • Screw on lid of transport container.
  • Fill in and insert transport documents.
  • Apply the warning notice for hazardous materials and information label to both ends of the transport container.
  • "Dangerous goods class 9"
  • "UN number 3480"
  • "Attention! Damaged lithium-ion battery"
  • "This side up"

Notes for transport preparation and hazardous material marking (Europe)

  1. "Protect against water"
  2. "Attention! Fragile"
  3. "This side up"
  4. "Maximum stacking load"
  5. "Hazardous material label: Hazardous material category 9 "Various hazardous substances and items" packaging group 2"
  6. "Type label with UN number UN 3480 for lithium-ion batteries"
    Volkswagen ID.4. Notes for transport preparation and hazardous material marking (Europe)