Senders/sensors/control units

In this manual: Senders/sensors/control units
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~12min read
0102030405086N·mlb·ft
Tightening torque found on this page
  • Removing and installing front parking aid senders [G252]/[G253]/[G254]/[G255]
  • Removing and installing rear parking aid senders [G203]/[G204]/[G205]/[G206]
  • Removing and installing front park assist steering senders [G568]/[G569]
  • Removing and installing rear park assist steering senders [G716]/[G717]
  • Removing and installing adaptive cruise control unit [J428]
  • Removing and installing control unit for overhead view camera [J928]
  • Removing and installing left/right overhead view camera R244/R245
  • Removing and installing parking aid control unit [J446]
  • Removing and installing reversing camera [R189]

Removing and installing front parking aid senders [G252]/[G253]/[G254]/[G255]

The front right parking aid sender -G252-, front centre right parking aid sender -G253-, front centre left parking aid sender -G254- and front left parking aid sender -G255- will henceforth be referred to as "sender".

Removing

Outer rear senders:

  • Detach front wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing front wheel housing liner.
  • Press locking devices in direction of -arrow- while simultaneously pressing sender -1- inwards from outside.
Volkswagen ID.4. Removing and installing front parking aid senders [G252]/[G253]/[G254]/[G255]
  • Disconnect electrical connector -2-, and pull it in a straight line off sender -1-.
  • Remove sender -1-.

All vehicles (continued)

Inner rear senders:

  • Remove bumper cover ⇒ General body repairs, exterior; Rep. gr. 63; Front bumper; Removing and installing bumper cover.
  • Press locking devices in direction of -arrow- while simultaneously pressing sender -1- inwards from outside.
Volkswagen ID.4. All vehicles (continued)
  • Disconnect electrical connector -2-, and pull it in a straight line off sender -1-.
  • Remove sender -1-.

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

NOTICE

Malfunctions due to the use of an unsuitable or damaged decoupling ring -3-.

  • Do not turn decoupling ring -3- on the sender head.
  • Renew decoupling ring -3- if unsuitable or damaged.
  • Check decoupling ring -3- on sender -1- for damage.
Volkswagen ID.4. All vehicles (continued)
  • Push electrical connector -2- in straight line on sender -1- and engage it.
  • When inserting sender -1- in sender retainer, make sure that the decoupling ring -3- is seated correctly on the sender head.
  • Insert sender -1- in a straight line into sender retainer.

Important

  • Locking devices of sender retainer must engage when installing sender -1-.

Removing and installing rear parking aid senders [G203]/[G204]/[G205]/[G206]

The rear left parking aid sender -G203-, rear centre left parking aid sender -G204-, rear centre right parking aid sender -G205- and rear right parking aid sender -G206- will henceforth be referred to as "sender".

Removing

Outer rear senders:

  • Press locking devices in direction of -arrow- while simultaneously pressing sender -1- inwards from outside.
Volkswagen ID.4. Removing and installing rear parking aid senders [G203]/[G204]/[G205]/[G206]
  • Disconnect electrical connector -2-, and pull it in a straight line off sender -1-.
  • Remove sender -1-.

All vehicles (continued)

Inner rear senders:

  • Remove bumper cover ⇒ General body repairs, exterior; Rep. gr. 63; Rear bumper; Removing and installing bumper cover.
  • Press locking devices in direction of -arrow- while simultaneously pressing sender -1- inwards from outside.
Volkswagen ID.4. Removing and installing rear parking aid senders [G203]/[G204]/[G205]/[G206]
  • Disconnect electrical connector -2-, and pull it in a straight line off sender -1-.
  • Remove sender -1-.

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

NOTICE

Malfunctions due to the use of an unsuitable or damaged decoupling ring -3-.

  • Do not turn decoupling ring -3- on the sender head.
  • Renew decoupling ring -3- if unsuitable or damaged.
  • Check decoupling ring -3- on sender -1- for damage.
Volkswagen ID.4. Removing and installing rear parking aid senders [G203]/[G204]/[G205]/[G206]
  • Push electrical connector -2- in straight line on sender -1- and engage it.
  • When inserting sender -1- in sender retainer, make sure that the decoupling ring -3- is seated correctly on the sender head.
  • Insert sender -1- in a straight line into sender retainer.

Important

  • Locking devices of sender retainer must engage when installing sender -1-.

Removing and installing front park assist steering senders [G568]/[G569]

The front left sender for park assist steering on left side of vehicle -G568- and front right sender for park assist steering on right side of vehicle -G569- will henceforth be referred to as "sender".

Removing

  • Detach front wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing front wheel housing liner.
  • Press locking devices in direction of -arrow- while simultaneously pressing sender -1- inwards from outside.
Volkswagen ID.4. Removing and installing front park assist steering senders [G568]/[G569]
  • Disconnect electrical connector -2-, and pull it in a straight line off sender -1-.
  • Remove sender -1-.

Installing

Install in reverse order of removal, observing the following:

NOTICE

Malfunctions due to the use of an unsuitable or damaged decoupling ring -3-.

  • Do not turn decoupling ring -3- on the sender head.
  • Renew decoupling ring -3- if unsuitable or damaged.
  • Check decoupling ring -3- on sender -1- for damage
Volkswagen ID.4. Removing and installing front park assist steering senders [G568]/[G569]
  • Push electrical connector -2- in straight line on sender -1- and engage.
  • When inserting sender -1- in sender retainer, make sure that the decoupling ring -3- is seated correctly on the sender head.
  • Insert sender -1- in a straight line into sender retainer.

Important

  • Locking devices of sender retainer must engage when installing sender -1-.

Removing and installing rear park assist steering senders [G716]/[G717]

The rear left park assist steering sender -G716- and rear right park assist steering sender -G717- will henceforth be referred to as "sender".

Removing

  • Detach rear wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing rear wheel housing liner.
  • Press locking devices in direction of -arrow- while simultaneously pressing sender -1- inwards from outside.
Volkswagen ID.4. Removing and installing rear park assist steering senders [G716]/[G717]
  • Disconnect electrical connector -2-, and pull it in a straight line off sender -1-.
  • Remove sender -1-.

Installing

Install in reverse order of removal, observing the following:

NOTICE

Malfunctions due to the use of an unsuitable or damaged decoupling ring-3-

  • Do not turn decoupling ring -3- on the sender head.
  • Renew decoupling ring -3- if unsuitable or damaged.
  • Check decoupling ring -3- on sender -1- for damage
Volkswagen ID.4. Removing and installing rear park assist steering senders [G716]/[G717]
  • Push electrical connector -2- in straight line on sender -1- and engage.
  • When inserting sender -1- in sender retainer, make sure that the decoupling ring -3- is seated correctly on the sender head.
  • Insert sender -1- in a straight line into sender retainer.

Important

Locking devices of sender retainer must engage when installing sender -1-.

Removing and installing adaptive cruise control unit [J428]

Removing

Adaptive cruise control unit -J428- is called control unit in this document.

If the control unit is renewed, perform the test plan for the renewal of the control unit:

  • Carry out function "Adaptive cruise control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Continued

  • Open bonnet.
  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing and installing adaptive cruise control unit [J428]
  • Unscrew bolts -1-.
  • Remove bracket -3- with control unit.

Installing

Install in reverse order of removal, observing the following:

If the control unit has been renewed, conclude the test plan for the renewal of the control unit:

  • Conclude function "Adaptive cruise control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Continued

  • ⇒ Rep. gr. 98; Adjusting/calibrating adaptive cruise control unit

Tightening torques

Removing and installing lane change assist control unit [J769]/[J770]

The lane change assist control unit -J769- and lane change assist control unit 2 -J770- will henceforth be referred to as "control unit".

Removal and installation are described for the left vehicle side as an example.

Removing

  • Remove bumper cover ⇒ General body repairs, exterior; Rep. gr. 63; Rear bumper; Removing and installing bumper cover.
  • Disconnect electrical connector -3-.
Volkswagen ID.4. Removing and installing lane change assist control unit [J769]/[J770]
  • Release locking device -2-.
  • Swing control unit -1- in direction of -arrow-, and remove it.
  • To remove bracket of control unit -1-, unscrew nut, and remove bracket.

Installing

Install in reverse order of removal, observing the following:

Tightening torques

Removing and installing lane change assist warning lamp in exterior mirror

Removal and installation are described for the left vehicle side as an example.

Removing

  • Remove upper mirror cover ⇒ General body repairs, exterior; Rep. gr. 66; Exterior mirrors; Removing and installing upper mirror cover.
  • Push area -3- in direction of -arrow A-, and hold it in that position.
Volkswagen ID.4. Removing and installing lane change assist warning lamp in exterior mirror
  • Press warning lamp -1- in direction of -arrow B- out of mirror cover -2-.

Installing

Install in reverse order of removal.

Removing and installing control unit for overhead view camera [J928]

Removing and installing control unit for overhead view camera [J928]

Control unit for overhead view camera -J928- is referred to hereafter as control unit.

Removing

If the control unit is renewed, perform the test plan for renewal of the control unit:

  • Carry out function "Renew control unit for overhead view camera" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Continued

  • Remove seat pan ⇒ General body repairs, interior; Rep.

    gr. 72; Rear seats; Removing and installing seat pan.

  • Separate electrical connectors.
Volkswagen ID.4. Removing and installing control unit for overhead view camera [J928]
  • Release spreader rivets -2-, and remove control unit -1-.

Installing

Install in the reverse order of removal, observing the following:

If the control unit has been renewed, conclude the test plan for the renewal of the control unit:

  • Conclude function "Renew control unit for overhead view camera" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Removing and installing holder for control unit for overhead view camera [J928]

Holder for control unit for overhead view camera -J928- is referred to hereafter as holder.

Removing

  • Remove control unit for overhead view camera -J928- ⇒ Rep. gr. 98; Removing and installing control unit for overhead view camera [J928].
  • Unscrew nuts -1-.
Volkswagen ID.4. Removing and installing holder for control unit for overhead view camera [J928]
  • Detach holder.

Installing

Install in the reverse order of removal, observing the following:

Tightening torques

Component / Specified torque

Nut on bracket / 8 N·m

Removing and installing left/right overhead view camera R244/R245

Left overhead view camera -R244- and right overhead view camera -R245- are called camera in this document.

Removal and installation are described for left vehicle side as an example.

Removing

  • Remove upper mirror cover ⇒ General body repairs, exterior; Rep. gr. 66; Exterior mirrors; Removing and installing upper mirror cover.
  • Unscrew bolts -2-.
Volkswagen ID.4. Removing and installing left/right overhead view camera R244/R245
  • Remove bracket -1- with camera -3-.
  • Separate electrical connector and remove camera -3- from bracket -1-.

Installing

Install in the reverse order of removal, observing the following:

  • ⇒ Rep. gr. 98; Calibrate overhead view camera.

Tightening torques

  • ⇒ General body repairs, exterior; Rep. gr. 66; Exterior mirror; Assembly overview - exterior mirror

Removing and installing left/right overhead view camera R244/R245

Removing and installing front camera for driver assist systems [R242]

Removing

Front camera for driver assist systems -R242- is called front camera in this document.

  • Remove bottom cover ⇒ General body repairs, interior; Rep.

    gr. 68; Interior mirror; Removing and installing interior mirror.

  • Unclip front camera -2- in direction of -arrow A-, and remove it in direction of -arrow B-.
Volkswagen ID.4. Removing and installing front camera for driver assist systems [R242]
  • Disconnect electrical connector -1-.

Installing

Install in reverse order of removal, observing the following:

Important

The field of view of the front camera on the inside of the windscreen must not be fogged or soiled.

  • Clean field of view of front camera with cleaning solution ⇒ Electronic parts catalogue (ETKA).
  • ⇒ Rep. gr. 98; Calibrate front camera for driver assist systems R242.

Removing and installing windscreen heater for front sensors [Z113]

Windscreen heater for front sensors -Z113- is referred to hereafter as windscreen heater.

Front camera for driver assist systems -R242- is called front camera in this document.

Removing

  • Remove front camera ⇒ Rep. gr. 98; Removing and installing front camera for driver assist systems [R242].
  • Move aside electrical wire, and disconnect electrical connector -3-.
Volkswagen ID.4. Removing and installing windscreen heater for front sensors [Z113]
  • Release locking device -2-.
  • Remove window heating -1- in direction of -arrow-.

Installing

Install in the reverse order of removal, observing the following:

Important

  • The field of view of the front camera on the inside of the windscreen must not be steamed up or soiled.
  • Clean field of view of front camera with cleaning solution ⇒ Electronic parts catalogue (ETKA).
  • ⇒ Rep. gr. 98; Calibrate front camera for driver assist systems R242.

Removing and installing parking aid control unit [J446]

The parking aid control unit -J446- will henceforth be referred to as "control unit".

Removing

  • Remove right luggage compartment side trim ⇒ General body repairs, interior; Rep. gr. 70; Luggage compartment trims; Removing and installing luggage compartment side trim.
  • Unscrew bolts -2-, and remove control unit -1-.
Volkswagen ID.4. Removing and installing parking aid control unit [J446]
  • Disconnect electrical connectors.

Installing

Install in reverse order of removal, observing the following:

Removing and installing front camera for driver assist systems [R242]

Removing

The front overhead view camera -R243- will henceforth be referred to as "camera".

  • Remove badge at front ⇒ General body repairs, exterior; Rep. gr. 66; Lettering and badges; Removing and installing badges at front.
  • Disconnect electrical connector.
  • Push locking devices in direction of -arrow-, and remove bracket -2-.
Volkswagen ID.4. Removing and installing front camera for driver assist systems [R242]
  • Pull camera -1- out of front badge.
Volkswagen ID.4. Removing and installing front camera for driver assist systems [R242]

Installing

Install in reverse order of removal, observing the following:

Important

  • Make sure that camera is correctly seated.
  • The bracket must be heard to engage.
  • ⇒ Rep. gr. 98; Calibrate overhead view camera.

Removing and installing reversing camera [R189]

Reversing camera -R189- will henceforth be referred to as "camera".

Removing

  • Remove rear lid handle ⇒ General body repairs, exterior; Rep. gr. 55; Rear lid; Removing and installing rear lid handle.
  • Release locking device -2-, and remove camera -1- in direction of -arrow-.
Volkswagen ID.4. Removing and installing reversing camera [R189]

Installing

Install in the reverse order of removal, observing the following:

  • ⇒ Rep. gr. 98; Calibrate reversing camera [R189].

Removing and installing rear overhead view camera [R246]

The rear overhead view camera -R246- will henceforth be referred to as "camera".

Removing

  • Remove rear lid handle ⇒ General body repairs, exterior; Rep. gr. 55; Rear lid; Removing and installing rear lid handle.
  • Release locking device -2-, and remove camera -1- in direction of -arrow-.
Volkswagen ID.4. Removing and installing rear overhead view camera [R246]

Installing

Install in the reverse order of removal, observing the following:

  • ⇒ Rep. gr. 98; Calibrate overhead view camera system.