Removing and installing rear motor

In this manual: Removing and installing rear motor
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
32steps
~192min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 32
  • Assembly overview - rear motor
  • Removing rear motor
  • Installing rear motor

Assembly overview - rear motor

Volkswagen ID.4. Removing and installing rear motor
  1. Potential equalisation line
  2. Bolt
  • 8 N·m
  1. Coolant hose
  2. Clamp
  3. Union
  4. Bolt
  • Renew after removing
  • 8 N·m +45º
  1. O-ring
  2. Bolt
  • Renew after removing
  • 130 N·m +180º
  1. Cable guide
  2. Bolt
  • Qty. 3
  • Renew after removing
  • 4 N·m +90º
  1. Electrical wire
  2. Cable guide
  3. O-ring
  4. Bolt
  • Qty. 2
  • Renew after removing
  • 8 N·m +45º
  1. Union
  2. Coolant hose
  3. Bolt
  • Qty. 3
  • Renew after removing
  • 70 N·m +180º
  1. Bolt
  • Renew after removing
  • 130 N·m +180º
  1. Motor support
  2. Electrical connector
  • High voltage
  1. Cable guide
  2. Bolt
  3. Qty. 2
  • 8 N·m
  1. Electrical connector
  • High voltage
  1. Bolt
  • Qty. 4
  • 8 N·m
  1. Three-phase current drive - VX54-
  • With power and control electronics for electric drive - JX1-
  • ⇒ Rep. gr. 10 ; Removing rear motor
  • ⇒ Rep. gr. 10 ; Installing rear motor
  1. Bolt
  • Renew after removing
  • 130 N·m +180º
  1. Breather line

Assembly overview - oil temperature sender

Volkswagen ID.4. Assembly overview - oil temperature sender
  1. Seal
  2. Oil temperature sender - G8-
  • ⇒ Rep. gr. 93 ; Removing and installing oil temperature sender -G8-
  1. Electrical connector
  2. Bolt
  • Qty. 2
  • Renew after removing
  • 8 N·m +45º
  1. Guard plate
  2. Bolt
  • Renew after removing
  • 8 N·m +45º

Removing rear motor

Special tools and workshop equipment required

  • Pin - 3282/29-
  • Pin - 3282/34-
  • Pin - 3282/50-
  • bit XZN 16 - T10198-
  • engine and gearbox jack - VAS 6931-
  • engine bung set - VAS 6122-
  • gearbox support - 3282-
  • lifting tackle - VAS 501 019-
  • workshop hoist - VAS 6100-

Three-phase current drive - VX54- with power and control electronics for electric drive - JX1- is referred to hereafter as "motor".

Removing

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; De-energise high-voltage system .
  • Remove rear centre underbody cladding -1- ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear centre underbody cladding .
  • Remove rear underbody cladding -2- ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear underbody cladding .
  • Remove stone deflector for spring control arm -3- ⇒ Running gear, axles, steering; Rep. gr. 42 ; Suspension link, track rod; Removing and installing stone deflector for spring control arm .
Volkswagen ID.4. Removing rear motor
  • Remove left and right drive shaft ⇒ Running gear, axles, steering; Rep. gr. 42 ; Drive shaft; Removing and installing drive shaft .
  • Remove rear left and right wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing and installing rear wheel housing liner .
  • ⇒ Rep. gr. 19 ; Drain coolant .

Note

For the bolt of the gearbox mounting to be renewed it is necessary to remove the charger.

  • Remove charging unit 1 for high-voltage battery - AX4- ⇒ Rep. gr. 93 ; Removing and installing charging unit 1 for high-voltage battery [AX4] .
  • Unclip coolant hose -1- as shown -arrow-.
  • Open clip -2- and pull coolant hose off -1-.
Volkswagen ID.4. Removing rear motor
  • Open clamp -arrow-, and pull off coolant hose -1-.
  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing rear motor
  • Fit gearbox support - 3282- -E- onto engine and gearbox jack - VAS 6931- -F-.
  • Screw in adapters into supports as follows:
Volkswagen ID.4. Removing rear motor
  1. Pin - 3282/34-
  2. Pin - 3282/50-
  3. Pin - 3282/50-
  4. Pin - 3282/29-
  • Position engine and gearbox jack -F- centrally under motor and gearbox -1-.
  • Align mountings -arrows- with mounting points in motor and gearbox.
  • Raise motor with gearbox to relieve load on motor mountings.
  • Use bit XZN 16 - T10198- to unscrew bolts -1- for left and right motor mountings through opening -arrow- in longitudinal member.
Volkswagen ID.4. Removing rear motor
  • Unscrew gearbox mounting bolt -arrow-.
Volkswagen ID.4. Removing rear motor
  • Lower motor with gearbox approx. 150 mm.
Volkswagen ID.4. Removing rear motor
  • Pull breather line for gearbox -1-.
  • Open clips -3-.
  • Unscrew bolts -arrows-.
  • Release and pull off high-voltage connector -2- ⇒ Rep.

    gr. 93 ; Disconnecting high-voltage connectors .

Volkswagen ID.4. Removing rear motor
  • Unscrew bolt -1- for potential equalisation line.
  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing rear motor

NOTICE

Risk of damage to lines and hoses when lowering the motor/ gearbox assembly.

  • Make sure that all connections between the motor/gearbox and the vehicle body have been disconnected.
  • When lowering, carefully guide motor/gearbox assembly out of motor compartment.
  • Lower motor with gearbox.
  • Seal any open connections on motor and gearbox with plugs from engine bung set - VAS 6122- .

Detaching motor from engine and gearbox jack

  • Fit bow - VAS 501 019/5-1- -1- and bow - VAS 501 019/5-2- -2- to lifting tackle. Screw in bolts -5-.
  • Secure shackle -4- in hole shown in illustration.
Volkswagen ID.4. Removing rear motor
  • Align bows -1- and -2- with markings -arrows-.
  • Tighten bolts -5-.
Volkswagen ID.4. Removing rear motor
  • Insert bows -1- and -2- of lifting tackle -A- into holes -arrows B-.
  • Screw bolt -3- by hand to stop into hole -arrow C-.
  • Attach workshop hoist - VAS 6100- to shackle -4-, and raise motor.
Volkswagen ID.4. Removing rear motor

Installing rear motor

Special tools and workshop equipment required

  • bit XZN 16 - T10198-
  • engine and gearbox jack - VAS 6931-
  • gearbox support - 3282-

Three-phase current drive - VX54- with power and control electronics for electric drive - JX1- is referred to hereafter as "motor".

Installing

Important

  • Motor and gearbox are secured to gearbox support - 3282- and engine and gearbox jack - VAS 6931- ⇒ Rep. gr. 10 ; Removing rear motor .
  • Raise motor with gearbox -1- up to 150 mm before installation position.
Volkswagen ID.4. Installing rear motor
  • Fit potential equalisation line -arrow-, and tighten bolt -1-.
  • Connect electrical connector -2-.
Volkswagen ID.4. Installing rear motor
  • Connect electrical connector -2-, and lock it.
  • Tighten bolts -arrows-.
  • Connect gearbox breather line -1-.
  • Engage clips -3-.
Volkswagen ID.4. Installing rear motor
  • Raise motor with gearbox -1- until bolts for motor and gearbox mountings can be started.
  • Tighten bolts for engine and gearbox mounting using bit XZN 16 - T10198- .
Volkswagen ID.4. Installing rear motor
  • Fit coolant hose -1-, and secure it with clip -2- .
  • Clip in coolant hose -1- -arrow-.
Volkswagen ID.4. Installing rear motor
  • Connect coolant hose -1-, and secure it with clamp -arrow-.
  • Connect electrical connector -2-.
Volkswagen ID.4. Installing rear motor
  • Install left and right drive shafts ⇒ Running gear, axles, steering; Rep. gr. 42 ; Drive shaft; Removing and installing drive shaft .

If three-phase current drive - VX54- with power and control electronics for electric drive - JX1- has been renewed:

Carry out function "power and control electronics for electric drive [JX1], commissioning" ⇒ Rep. gr. 00 ; Access to diagnoses .

Note

At the end of the diagnosis, the function "Calibrate electric drive motor" is carried out automatically.

Continued

Further installation is carried out in reverse order of removal, observing the following:

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; Re-energise high-voltage system .

Tightening torques

  • ⇒ Rep. gr. 10 ; Assembly overview - motor
  • ⇒ Rep. gr. 93 ; Assembly overview - charging unit for high-voltage battery
  • ⇒ Running gear, axles, steering; Rep. gr. 42 ; Drive shaft; Assembly overview - drive shaft
  • ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Assembly overview - underbody cladding