Luggage compartment trims

In this manual: Luggage compartment trims
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
4steps
~24min
2/5difficulty
0102030405021N·mlb·ft
Tightening torque found on this page
Done 0 of 4
  • Overview of fitting locations - luggage compartment trims
  • Assembly overview - luggage compartment side trim
  • Assembly overview - lower rear lid trim
  • Removing and installing lower rear lid trim
  • Removing and installing luggage compartment side trim
  • Removing and installing side rear lid trim

Overview of fitting locations - luggage compartment trims

Volkswagen ID.4. Overview of fitting locations - luggage compartment trims
  1. Lower rear lid trim
  • ⇒ Rep. gr. 70 ; Assembly overview - lower rear lid trim
  • ⇒ Rep. gr. 70 ; Removing and installing lower rear lid trim
  1. Side rear lid trim
  • ⇒ Rep. gr. 70 ; Assembly overview - upper rear lid trim
  • ⇒ Rep. gr. 70 ; Removing and installing side rear lid trim
  1. Upper rear lid trim
  • ⇒ Rep. gr. 70 ; Assembly overview - upper rear lid trim
  • ⇒ Rep. gr. 70 ; Removing and installing upper rear lid trim
  1. Rear shelf
  2. Luggage compartment floor covering
  • ⇒ Rep. gr. 70 ; Assembly overview - luggage compartment floor
  1. Luggage compartment side trim
  • ⇒ Rep. gr. 70 ; Assembly overview - luggage compartment side trim
  • ⇒ Rep. gr. 70 ; Removing and installing luggage compartment side trim
  1. Lock carrier trim
  • ⇒ Rep. gr. 70 ; Removing and installing lock carrier trim
  1. Luggage compartment floor
  • Depending on equipment/version
  • ⇒ Rep. gr. 70 ; Assembly overview - luggage compartment floor
  1. Luggage compartment floor bracket
  • Depending on equipment/version
  • ⇒ Rep. gr. 70 ; Assembly overview - luggage compartment floor
  • ⇒ Rep. gr. 70 ; Removing and installing support for luggage compartment floor

Assembly overview - luggage compartment side trim

The overview is shown for the left side of vehicle as an example.

  1. Luggage compartment side trim
  • ⇒ Rep. gr. 70 ; Removing and installing luggage compartment side trim
  1. Bolt
  • 2 N·m
Volkswagen ID.4. Assembly overview - luggage compartment side trim

Assembly overview - luggage compartment floor

  1. Luggage compartment floor
  • Depending on equipment/ version
  1. Luggage compartment floor covering
  2. Bolt
  • Depending on equipment/ version
  • Qty. 6
  • 8 N·m
  1. Luggage compartment floor bracket
  • Depending on equipment/ version
  • ⇒ Rep. gr. 70 ; Removing and installing support for luggage compartment floor
Volkswagen ID.4. Assembly overview - luggage compartment floor

Assembly overview - lower rear lid trim

  1. Lower rear lid trim
  • ⇒ Rep. gr. 70 ; Removing and installing lower rear lid trim
  1. Bolt
  • Depending on equipment/ version
  • Depending on model
  • Qty. 2
  • 1,5 N·m
  1. Cap
  • Qty. 2
  1. Bolt
  • Qty. 2
  • 1,5 N·m
Volkswagen ID.4. Assembly overview - lower rear lid trim

Assembly overview upper rear lid trim

  1. Upper rear lid trim
  • ⇒ Rep. gr. 70 ; Removing and installing upper rear lid trim
  1. Rear lid side trim
  • ⇒ Rep. gr. 70 ; Removing and installing side rear lid trim
Volkswagen ID.4. Assembly overview   upper rear lid trim

Removing and installing lower rear lid trim

Special tools and workshop equipment required

  • removal tool - T40280-
  • removal wedge - 80-200-

Removing

  • Remove warning triangle.
  • Remove side rear lid trim ⇒ "7.11 Removing and installing side rear lid trim".
  • Unclip caps -1- using commercially available plastic wedge.
Volkswagen ID.4. Removing and installing lower rear lid trim
  • Unscrew bolts -1-.
Volkswagen ID.4. Removing and installing lower rear lid trim
  • Use removal wedge - 80-200- to unclip lower rear lid trim -2- from rear lid -1-.
Volkswagen ID.4. Removing and installing lower rear lid trim

Vehicles with electrically operated rear lid

  • Disconnect electrical connector for rear lid closure button - E574- .

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

  • Remove any retaining clips left in rear lid using removal tool - T40280- , and insert them into lower rear lid trim for installation.

Tightening torques

  • ⇒ Rep. gr. 70 ; Assembly overview - lower rear lid trim

Removing and installing upper rear lid trim

Special tools and workshop equipment required

  • removal tool - T40280-
  • removal wedge - 80-200-

Removing

  • Use removal wedge - 80-200- to unclip upper rear lid trim -2- from rear lid -1-.
Volkswagen ID.4. Removing and installing upper rear lid trim

Installing

Install in reverse order of removal, observing the following:

  • Remove any retaining clips left in rear lid using removal tool - T40280- , and insert them into upper rear lid trim for installation.

Removing and installing luggage compartment side trim

Removing

Removal and installation are described for the left side of vehicle as an example.

  • Remove rear shelf.
  • Remove first aid kit.
  • Fold rear seat backrest towards front.
  • Remove lock carrier trim ⇒ Rep. gr. 70 ; Removing and installing lock carrier trim .
  • Remove C-pillar trim ⇒ Rep. gr. 70 ; Removing and installing C-pillar trim .
  • Release rear sill panel moulding ⇒ "6.8 Removing and installing rear sill panel moulding"

Vehicles with luggage compartment floor

  • Remove luggage compartment floor.
  • Remove support for luggage compartment floor ⇒ Rep.

    gr. 70 ; Removing and installing support for luggage compartment floor .

All vehicles (continued)

  • Remove luggage compartment floor covering.
  • Free off luggage compartment side trim -2- in area of rear lid seal.
  • Unscrew bolt -1-
  • Unclip luggage compartment side trim -2- in direction of -arrow-.
Volkswagen ID.4. Removing and installing luggage compartment side trim
  • Disconnect electrical connectors.
  • Guide out the outer rear three-point seat belt.

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 70 ; Assembly overview - luggage compartment side trim

Removing and installing lock carrier trim

Special tools and workshop equipment required

  • removal tool - T40280-

Removing

Vehicles with luggage compartment floor

  • Remove luggage compartment floor.

All vehicles (continued)

  • Remove luggage compartment floor covering.
  • Free off lock carrier trim -1- in area of rear lid seal.
  • Remove lock carrier trim -1- upwards.
Volkswagen ID.4. Removing and installing lock carrier trim

Installing

Install in reverse order of removal, observing the following:

  • Remove any retaining clips left in body using removal tool - T40280- , and insert them into lock carrier trim for installation.

Removing and installing support for luggage compartment floor

Removing

Removal and installation are described for left side of vehicle as an example.

  • Remove luggage compartment floor.
  • Unscrew bolts -1- and -3-.
  • Swivel support for luggage compartment floor -4- in direction of -arrow a-.
  • Pull support for luggage compartment floor -4- towards front and out of luggage compartment side trim -2- -arrow b-, and remove it.
Volkswagen ID.4. Removing and installing support for luggage compartment floor

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 70 ; Assembly overview - luggage compartment floor

Removing and installing side rear lid trim

Special tools and workshop equipment required

  • removal tool - T40280-

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove upper rear lid trim ⇒ Rep. gr. 70 ; Removing and installing upper rear lid trim .
  • Release side rear lid trim -1- in direction of -arrow B-.
  • Remove side rear lid trim -1- from rear lid -2- in direction of -arrow A-.
Volkswagen ID.4. Removing and installing side rear lid trim

Installing

Install in reverse order of removal, observing the following:

  • Remove any retaining clips left in rear lid using removal tool - T40280- , and insert them into side rear lid trim for installation.