Door components

In this manual: Door components
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
4steps
~24min
2/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 4
  • Assembly overview - door components
  • Assembly overview - assembly carrier
  • Assembly overview - door handle and door lock
  • Removing and installing rear window regulator motor [V471]/[V472]
  • Removing and installing rear exterior door handle [EX8]/[EX9]
  • Dismantling and assembling rear exterior door handle [EX8]/[EX9]
  • Removing and installing mounting bracket
  • Removing and installing rear door lock unit [VX83]/[VX84]
  • Removing and installing assembly carrier
  • Removing and installing window channel
  • Removing and installing outer window slot seal
  • Removing and installing window slot inner seal
  • Removing and installing operating cable for exterior door handle
  • Removing and installing operating cable for interior door handle

Assembly overview - door components

Overview shown for left side of vehicle as an example

  1. Door
  • ⇒ Rep. gr. 58 ; Removing and installing door
  • ⇒ Rep. gr. 58 ; Adjusting door
  1. Outer window slot seal
  • ⇒ Rep. gr. 58 ; Removing and installing outer window slot seal
  1. Window channel
  • ⇒ Rep. gr. 58 ; Removing and installing window channel
  1. Door joint seal
  • Renew after removing
  • ⇒ Rep. gr. 58 ; Removing and installing outer door seal
  1. Inner window slot seal
  • ⇒ Rep. gr. 58 ; Removing and installing window slot inner seal
  1. Plug
  2. Damping for outer door panel on inside
  • Self-adhesive
  • Dimensions ⇒ Electronic parts catalogue (ETKA)
  • Qty. 2
  • ⇒ General information - body; Rep. gr. 52 ; General procedures; Removing and installing insulation for inner side of door outer panel
  1. Plug
  2. Plug
    Volkswagen ID.4. Assembly overview - door components

Assembly overview - assembly carrier

Overview shown for left side of vehicle as an example

  1. Door subframe
  • ⇒ Rep. gr. 58 ; Removing and installing assembly carrier
  1. Plug
  • Depending on equipment/ version
  1. Bolt
  • 8 N·m
  1. Clip
  • Qty. 8
  1. Rear driver side window regulator motor - V471- / rear passenger side window regulator motor - V472-
  • ⇒ Rep. gr. 58 ; Removing and installing rear window regulator motor [V471]/[V472]
  1. Bolt
  • Qty. 3
  • 3 N·m
  1. Plug
Volkswagen ID.4. Assembly overview - assembly carrier

Assembly overview - door handle and door lock

Overview is shown for left side of vehicle as an example

  1. Bowden cable
  • From rear door lock unit to interior door handle
  • ⇒ Rep. gr. 58 ; Removing and installing Bowden cable for interior door handle
  1. Rear door lock unit, driver side - VX83- / rear door lock unit, passenger side - VX84-
  • ⇒ Rep. gr. 58 ; Removing and installing rear door lock unit [VX83]/[VX84]
  1. Bolt
  • Qty. 2
  • 18 N·m
  1. Bowden cable
  • From rear door lock unit to mounting bracket
  • ⇒ Rep. gr. 58 ; Removing and installing Bowden cable for exterior door handle
  1. Mounting bracket
  • ⇒ Rep. gr. 58 ; Removing and installing mounting bracket
  1. Carrier
  • Renew after removing
  1. Trim
  • Can only be renewed with exterior door handle
  1. Rear left exterior door handle - EX8- / rear right exterior door handle - EX9-
  • Depending on equipment/version
  • With light for rear exterior door handle illumination, driver side - L285- / light for rear exterior door handle illumination, passenger side - L286-
  • ⇒ Rep. gr. 58 ; Removing and installing rear exterior door handle [EX8]/[EX9]
  • ⇒ Rep. gr. 58 ; Dismantling and assembling rear exterior door handle [EX8]/[EX9]
Volkswagen ID.4. Assembly overview - door handle and door lock

Removing and installing rear window regulator motor [V471]/[V472]

Rear driver side window regulator motor - V471- and rear passenger side window regulator motor - V472- are referred to hereafter as window regulator motor.

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove rear door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Rear door trim; Removing and installing rear door trim .

CAUTION

Risk of injury to hands and eyes due to glass splinters.

Danger of cutting yourself.

  • Put on safety goggles.
  • Put on protective gloves.

NOTICE

Risk of damage to the door window from sliding down.

The door window could become scratched or chipped.

  • Fix the door window in position using adhesive tape.
  • Fix rear door window in position using commercially available adhesive tape.
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-.
  • Remove window regulator motor -1-.
Volkswagen ID.4. Removing and installing rear window regulator motor [V471]/[V472]

Installing

Install in reverse order of removal, observing the following:

  • Insert window regulator motor -1- on assembly carrier -2-.

    When doing this, move door window up and down until teeth align.

Volkswagen ID.4. Removing and installing rear window regulator motor [V471]/[V472]
  • Adapt window regulator motor ⇒ Maintenance ; Booklet ; Window regulator: Checking position .

Tightening torques

  • ⇒ Rep. gr. 58 ; Assembly overview - assembly carrier

Removing and installing striker pin

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Unscrew bolts -2-.
  • Remove striker pin -1-.
Volkswagen ID.4. Removing and installing striker pin

Removing

  • Unscrew bolts -2-.
  • Remove striker pin -1-.

Installing

Install in reverse order of removal, observing the following:

Striker pin with curvature

  • Fit striker pin on C-pillar with curvature facing inwards.

All vehicles (continued)

  • ⇒ Rep. gr. 58 ; Adjust striker pin .

Tightening torques

  • ⇒ Rep. gr. 58 ; Assembly overview - door

Removing and installing rear exterior door handle [EX8]/[EX9]

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.

Removing

Rear left exterior door handle - EX8- and rear right exterior door handle - EX9- are referred to hereafter as door handle.

Removal and installation are described for left side of vehicle as an example.

  • Remove assembly carrier ⇒ Rep. gr. 58 ; Removing and installing assembly carrier .
  • Disconnect electrical connector -1-.
  • Unscrew bolts -2-, and lower the rear door lock unit, driver side - VX83- / rear door lock unit, passenger side - VX84- -3-.
Volkswagen ID.4. Removing and installing rear exterior door handle [EX8]/[EX9]
  • Lever off plug -1-.

Left side of vehicle:

  • Turn eccentric -2- 180º in direction of -arrow- .

Right side of vehicle:

  • Turn eccentric -2- 180º in opposite direction of -arrow-.
Volkswagen ID.4. Removing and installing rear exterior door handle [EX8]/[EX9]
  • Press and hold rocker switch -2- through opening.
  • Slide sliding plate -1- to stop in direction of -arrow-.
  • Disconnect electrical connector of door handle.
Volkswagen ID.4. Removing and installing rear exterior door handle [EX8]/[EX9]
  • Swing out door handle -1- in direction of -arrow-, and remove it.
Volkswagen ID.4. Removing and installing rear exterior door handle [EX8]/[EX9]

Installing

Install in reverse order of removal, observing the following:

  • Swivel in door handle, and let it engage in mounting bracket
  • Using commercially available Torx "T30" driver, turn eccentric on mounting bracket until it engages audibly in eccentric end position.
  • Perform functional check with the door open.

Tightening torques

  • ⇒ Rep. gr. 58 ; Assembly overview - door handle and door lock

Dismantling and assembling rear exterior door handle [EX8]/[EX9]

Special tools and workshop equipment required

  • assembly tool - T10118-
  • commercially available drift
  • commercially available flat-bladed screwdriver
  • commercially available pliers

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.

Rear left exterior door handle - EX8- and rear right exterior door handle - EX9- are referred to hereafter as door handle.

light for rear exterior door handle illumination, driver side - L285- and light for rear exterior door handle illumination, passenger side - L286- will henceforth be referred to as "light for exterior door handle illumination".

The dismantling and assembling procedures are described for the left door handle as an example.

Dismantling

  • Remove door handle ⇒ Rep. gr. 58 ; Removing and installing rear exterior door handle [EX8]/[EX9] .
  • Push spring -1- in direction of -arrow A-.
  • Using commercially available flat-bladed screwdriver -2-, turn spring -1- 90º in direction of -arrow B- and detach from mounting.
Volkswagen ID.4. Dismantling and assembling rear exterior door handle [EX8]/[EX9]
  • Detach electrical connector of light for exterior door handle illumination -2- in direction of -arrow A-.
  • Using commercially available drift , drive out pin -3- in direction of -arrow B-, and pull it out.
  • Detach spring -1- from door handle -4-.
Volkswagen ID.4. Dismantling and assembling rear exterior door handle [EX8]/[EX9]

Important

  • Trim -1- must not be removed.
  • Remove liner -3- from door handle -2-, and remove adhesive residue, if there is any ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for selfadhesive components .
Volkswagen ID.4. Dismantling and assembling rear exterior door handle [EX8]/[EX9]

Assembling

Assemble in the reverse order of disassembly, observing the following:

  • Insert spring -1- into door handle -2-.
  • Insert pin -3- in direction of -arrow A-, and press it on firmly using commercially available pliers .
Volkswagen ID.4. Dismantling and assembling rear exterior door handle [EX8]/[EX9]
  • Using assembly tool - T10118- -2-, turn spring -1- 90º in direction of -arrow A- until hook is engaged in mounting.
  • Push spring -1- apart in central area -3-.
Volkswagen ID.4. Dismantling and assembling rear exterior door handle [EX8]/[EX9]

Removing and installing mounting bracket

Removing

Removal and installation are described for left side of vehicle as an example.

  • Remove rear door lock unit, driver side - VX83- / rear door lock unit, passenger side - VX84- ⇒ Rep. gr. 58 ; Removing and installing rear door lock unit [VX83]/[VX84] .
  • Remove rear left exterior door handle - EX8- / rear right exterior door handle - EX9- ⇒ Rep. gr. 58 ; Removing and installing rear exterior door handle [EX8]/[EX9] .
  • Guide electrical wire out of guides -2-.
  • Push mounting bracket -3- to stop in direction of -arrow A-, and remove it in direction of -arrow B-.
Volkswagen ID.4. Removing and installing mounting bracket
  • Swivel out Bowden cable -4- in direction of -arrow A-.
  • Detach Bowden cable -4- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing mounting bracket

Installing

Install in reverse order of removal, observing the following:

Important

  • Guides and retaining hooks of mounting bracket must engage behind metal tabs of door outer panel
  • Perform functional check with the door open.

Removing and installing rear door lock unit [VX83]/[VX84]

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.

The rear door lock unit, driver side - VX83- and rear door lock unit, passenger side - VX84- will henceforth be referred to as "door lock".

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove assembly carrier ⇒ Rep. gr. 58 ; Removing and installing assembly carrier .
  • Disconnect electrical connector -1-.
  • Unscrew bolts -2-.
  • Remove door lock -3- in direction of -arrow-.
Volkswagen ID.4. Removing and installing rear door lock unit [VX83]/[VX84]

New door lock

  • Remove Bowden cable for exterior door handle ⇒ Rep. gr. 58 ; Removing and installing Bowden cable for exterior door handle .
  • Remove Bowden cable for interior door handle ⇒ Rep. gr. 58 ; Removing and installing Bowden cable for interior door handle .

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

  • Perform functional check with the door open.

Tightening torques

  • ⇒ Rep. gr. 58 ; Assembly overview - door handle and door lock

Removing and installing assembly carrier

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove rear door trim ⇒ General body repairs; interior; Rep. gr. 70 ; Rear door trims; Removing and installing rear door trim .
  • Detach rear door window from window regulator ⇒ Rep. gr. 64 ; Removing and installing rear door window .
  • Push rear door window upwards, and secure it with adhesive tape to prevent it from falling down.
  • Lever off plug -1-.
  • Unscrew bolt -2-.
  • Disconnect electrical connectors -3-.
  • Loosen clips -4-, and lay electrical wires aside.
Volkswagen ID.4. Removing and installing assembly carrier
  • Turn clips -1- 90º in direction of -arrow A-, and pull them out slightly.
  • Pull assembly carrier -2- in direction of -arrow B- out of door.
Volkswagen ID.4. Removing and installing assembly carrier

Installing

Install in reverse order of removal, observing the following:

  • Insert spreader plug and spreader rivet ⇒ Rep. gr. 64 ;

Removing and installing rear door window .

Important

  • Installation sequence of clips must be adhered to.
  • Clips must engage audibly.
  • 3 Install clips on upper left and upper right.
  • Install remaining clips.

Tightening torques

  • ⇒ Rep. gr. 58 ; Assembly overview - assembly carrier

Removing and installing window channel

NOTICE

Risk of damage to window channel from applying excessive force.

The metal insert of the window channel may be bent.

  • Handle window channel with care.

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove inner window slot seal ⇒ Rep. gr. 58 ; Removing and installing inner window slot seal .
  • Remove outer window slot seal ⇒ Rep. gr. 58 ; Removing and installing outer window slot seal .
  • Remove B-pillar trim on rear door ⇒ "3.13.2 Removing and installing B-pillar trim on rear door" .
  • Loosen upper clips of fixed rear door window ⇒ Rep. gr. 64 ; Removing and installing fixed rear door window .
  • Pull off window channel -1- in area -6- in direction of -arrow B-.
  • Guide out window channel -1- in area -3-.
  • Pull off window channel -1- evenly in direction of -arrow A- in areas -3-, -2- and -7-, starting at fixed rear door window.
  • Pull off window channel -1- in area -5- in direction of -arrow C-.
  • Pull off window channel -1- in area -4- in direction of -arrow B-.
  • Pull window channel -1- in areas -4- and -5- out of door mountings.
  • Pull off window channel -1- in area -2- in direction of -arrow C-, and remove it.
Volkswagen ID.4. Removing and installing window channel

Installing

Install in reverse order of removal, observing the following:

NOTICE

Uneven seating and fit of the window channel after installation.

Wind noise is possible.

  • Ensure that item is seated and comes into contact correctly when aligning and installing.
  • Moisten window channel with soapy solution to facilitate installation.
  • Push window channel -1- in areas -4- and -5- into door mountings.
  • Fit window channel -1- in area -2- in opposite direction of -arrow C-.
  • Fit window channel -1- in area -7- in opposite direction of -arrow A-, and align it with B-pillar trim on rear door.
  • Starting at top, push on window channel -1- in area -6-.
  • Starting at B-pillar, evenly push on window channel -1- in areas -2- and -7-.
  • Push on window channel -1- in area -3- at fixed rear door window.
  • Secure fixed rear door window ⇒ Rep. gr. 64 ; Removing and installing fixed rear door window .
  • Push on window channel -1- in areas -4- and -5-.
Volkswagen ID.4. Removing and installing window channel

Removing and installing outer window slot seal

Special tools and workshop equipment required

  • removal wedge set - VAS 895 015-
  • wedge - T10039/1-

Removing

Removal and installation are described for left side of vehicle as an example.

Outer window slot seal is referred to hereafter as window slot seal.

Design of window slot seal varies depending on equipment/version.

  • Insert wedge no. 3 -5- from removal wedge set - VAS 895 015- between window slot seal -1- and B-pillar trim on rear door -4-.

NOTICE

Risk of damage to outer window slot seal due to incorrect removal

If the metal insert in the window slot seal is bent, the window slot seal can no longer be straightened out.

  • Pull off the window slot seal evenly without bending it.
  • Using wedge - T10039/1- -3-, lever window slot seal -1- evenly off door flange -2- in direction of -arrow- starting from outside.
Volkswagen ID.4. Removing and installing outer window slot seal

Installing

Install in reverse order of removal, observing the following:

Vehicles with end cap on window slot seal:

  • Fit end cap of window slot seal before "B-pillar trim", and push it under trim contour.

All vehicles (continued)

  • Align window slot seal flush relative to joint with outer part of door.

NOTICE

Risk of damage to the outer window slot seal due to incorrect installation If the metal insert in the window slot seal is bent, the window slot seal can no longer be straightened out.

  • Install the window slot seal evenly without bending it.

Important

  • Impact tools must not be used for installing window slot seal
  • Fit window slot seal evenly onto door flange by hand, starting at B-pillar.

Removing and installing window slot inner seal

Removal and installation are described for left side of vehicle as an example.

Inner window slot seal will henceforth be referred to as "window slot seal".

Design of window slot seal varies depending on equipment/version.

Removing

  • Remove rear door trim ⇒ General body repairs; interior; Rep. gr. 70 ; Rear door trims; Removing and installing rear door trim .

NOTICE

Risk of damage to the window slot seal due to incorrect removal.

The window slot seal may become bent.

  • Proceed with caution when levering off the window slot seal.
  • Lever window slot seal -1- in direction of -arrow A- evenly off door flange -2-.
Volkswagen ID.4. Removing and installing window slot inner seal

Installing

Install in reverse order of removal, observing the following:

  • Position window slot seal -1- in direction of -arrow A- centrally between front section of window guide -4- and rear section of fixed rear door window -3-.
  • Press window slot seal -1- in direction of "arrow B" evenly by hand onto door flange -2- starting at centre strut of -fixed door window-.
Volkswagen ID.4. Removing and installing window slot inner seal

Vehicles with foam strip on centre strut moulding:

  • Position centre strut moulding with foam strip so that it is flush with "fixed door window".

Important

  • Make sure that foam is pressed on excessively.

Removing and installing operating cable for exterior door handle

The rear door lock unit, driver side - VX83- and rear door lock unit, passenger side - VX84- will henceforth be referred to as "door lock".

The removal and installation procedures are described for the left side of the vehicle as an example.

Removing

  • Remove door lock ⇒ Rep. gr. 58 ; Removing and installing rear door lock unit [VX83]/[VX84]

Door lock with cover

  • Open cover -2- in direction of -arrow A-.
  • Turn Bowden cable -3- 90º in direction of -arrow A-, and unclip it in direction of -arrow C-.
  • Detach Bowden cable -3- in direction of -arrow D- from door lock -1-, and remove Bowden cable.
Volkswagen ID.4. Removing and installing operating cable for exterior door handle

All vehicles (continued)

Door lock with SAFELOCK

  • Turn Bowden cable -2- 90º in direction of -arrow A-, and remove it from retainer.
  • Swing Bowden cable -2- in direction of -arrow B- until Bowden cable -2- can be guided out of eyelet in door lock -1- in direction of -arrow C-.
Volkswagen ID.4. Removing and installing operating cable for exterior door handle

All vehicles (continued)

Door lock without SAFELOCK

  • Turn Bowden cable -2- 90º in direction of -arrow A-, and remove it from retainer.
  • Swing Bowden cable -2- in direction of -arrow B- until Bowden cable -2- can be guided out of eyelet in door lock -1- in direction of -arrow C-.
Volkswagen ID.4. Removing and installing operating cable for exterior door handle

All vehicles (continued)

Installing

Installation is carried out in reverse sequence.

Removing and installing operating cable for interior door handle

The rear door lock unit, driver side - VX83- and rear door lock unit, passenger side - VX84- will henceforth be referred to as "door lock".

The removal and installation procedures are described for the left side of the vehicle as an example.

Removing

  • Remove door lock ⇒ Rep. gr. 58 ; Removing and installing rear door lock unit [VX83]/[VX84] .

Door lock with flap for Bowden cable

  • Open flap -2- in direction of -arrow D-.
  • Turn Bowden cable -3- 90º in direction of -arrow A- and swivel out in direction of -arrow B-.
  • Swing Bowden cable -2- until Bowden cable -3- can be guided out of eyelet in door lock -1- in direction of -arrow C-.
  • Guide out Bowden cable -2-.
Volkswagen ID.4. Removing and installing operating cable for interior door handle

All vehicles (continued)

Door lock without flap for Bowden cable

  • Turn Bowden cable -2- 90º in direction of -arrow A- and swivel out in direction of -arrow B-.
  • Swing Bowden cable -2- until Bowden cable -2- can be guided out of eyelet in door lock -1- in direction of -arrow C-.
  • Guide out Bowden cable -2-.
Volkswagen ID.4. Removing and installing operating cable for interior door handle

All vehicles (continued)

Installing

Installation is carried out in reverse sequence.