Rear seat covers and padding

In this manual: Rear seat covers and padding
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
2steps
~12min
1/5difficulty
Done 0 of 2
  • Assembly overview - rear bench seat cover and padding
  • Assembly overview - rear seat backrest cover and padding
  • Removing and installing cover and padding of rear bench seat
  • Removing and installing cover and padding of rear seat backrest
  • Separating rear bench seat cover from padding
  • Separating rear seat backrest cover from padding

Assembly overview - rear bench seat cover and padding

Volkswagen ID.4. Assembly overview - rear bench seat cover and padding
  1. Seat cover
  • Depending on equipment/ version
  • ⇒ Rep. gr. 74 ; Removing and installing cover and padding of rear bench seat
  • ⇒ Rep. gr. 74 ; Separating rear bench seat cover from padding
  1. Piping strip
  • Sewn to seat cover
  1. Seat occupied sensor
  • Rear seat occupied sensor on driver side - G177-
  • Rear seat occupied sensor, centre - G1010-
  • Rear seat occupied sensor on passenger side - G178-
  • ⇒ Rep. gr. 69 ; Removing and installing rear seat occupied sensor [G177/ G178/G1010]
  1. Seat padding
  • Depending on equipment/ version
  • ⇒ Rep. gr. 74 ; Removing and installing cover and padding of rear bench seat
  • ⇒ Rep. gr. 74 ; Separating rear bench seat cover from padding
  1. Upholstery clip
  • Renew after removing

Assembly overview - rear seat backrest cover and padding

The overview is shown for the rear seat backrest (2/3) as an example.

  1. Backrest cover
  • Depending on equipment/ version
  • ⇒ Rep. gr. 74 ; Removing and installing cover and padding of rear seat backrest
  • ⇒ Rep. gr. 74 ; Separating rear seat backrest cover from padding
  1. Upholstery clip
  • Renew after removing
  1. Backrest padding
  • Depending on equipment/ version
  • ⇒ Rep. gr. 74 ; Removing and installing cover and padding of rear seat backrest
  • ⇒ Rep. gr. 74 ; Separating rear seat backrest cover from padding
  1. Backrest frame
  2. Beading strip
  • Sewn to backrest cover
Volkswagen ID.4. Assembly overview - rear seat backrest cover and padding

Removing and installing cover and padding of rear bench seat

Special tools and workshop equipment required

  • hook - 3370-

Removing

  • Remove bench seat ⇒ Rep. gr. 72 ; Removing and installing bench seat/individual seats .
  • Unclip child seat anchor guide of rear bench seat -1- upwards from rear bench seat -2-.
Volkswagen ID.4. Removing and installing cover and padding of rear bench seat
  • Open securing channel and Velcro fastener -3-.
  • Using hook - 3370- , open beading strips -1-.
  • Remove cover -2- together with padding.
Volkswagen ID.4. Removing and installing cover and padding of rear bench seat

Installing

Install in reverse sequence of removal.

Removing and installing cover and padding of rear seat backrest

Removing

  • Remove rear seat backrest ⇒ Rep. gr. 72 ; Removing and installing rear seat backrest .
  • Remove head restraint ⇒ Rep. gr. 72 ; Removing and installing head restraint .
  • Remove head restraint guides ⇒ Rep. gr. 72 ; Removing and installing head restraint guide .
  • Remove locking mechanism trim ⇒ Rep. gr. 72 ; Removing and installing locking mechanism trim .
  • Using commercially available plastic wedge, release clip -2- from cover -1- in area of inner pivot pin.
Volkswagen ID.4. Removing and installing cover and padding of rear seat backrest

Rear left seat backrest (1/3)

  • Starting at locking mechanism, lever beading strip -1- in direction of -arrow- all around off backrest frame -3-.
  • Remove cover -2- together with padding.
Volkswagen ID.4. Removing and installing cover and padding of rear seat backrest

All vehicles (continued)

Rear seat backrest (2/3) without load-through hatch

  • Remove rear belt guide ⇒ Rep. gr. 69 ; Removing and installing rear belt guide .
  • Starting at locking mechanism, lever beading strip -1- in direction of -arrow- all around off backrest frame -3-.
  • Remove cover -2- together with padding.
Volkswagen ID.4. Removing and installing cover and padding of rear seat backrest

All vehicles (continued)

Rear seat backrest (2/3) with load-through hatch

  • Remove rear belt guide ⇒ Rep. gr. 69 ; Removing and installing rear belt guide .
  • Remove flap for load-through hatch ⇒ Rep. gr. 72 ; Removing and installing flap for load-through hatch .
  • Remove trim frame for load-through hatch ⇒ Rep. gr. 72 ; Removing and installing trim frame for load-through hatch .
  • Starting at locking mechanism, lever beading strip -1- in direction of -arrow- all around off backrest frame -4-.
  • Lever beading strip -2- all around off load-through hatch.
  • Remove cover -3- together with padding.
Volkswagen ID.4. Removing and installing cover and padding of rear seat backrest

All vehicles (continued)

Installing

Install in reverse sequence of removal.

Removing and installing intermediate padding, backrest with load-through hatch

Removing

  • Fold down flap for load-through hatch.
  • Release fasteners -1- using a commercially available screwdriver while at the same time pushing intermediate padding -2- as far as stop in direction of -arrow A-.
  • Slightly raise intermediate padding in direction of -arrow B-, and detach it in direction of -arrow C-.
Volkswagen ID.4. Removing and installing intermediate padding, backrest with load-through hatch

Installing

Install in reverse sequence of removal.

Separating rear bench seat cover from padding

Special tools and workshop equipment required

  • upholstery clip pliers - V.A.G 1634B

Removing

  • Remove cover and padding of rear bench seat ⇒ Rep. gr. 74 ; Removing and installing cover and padding of rear bench seat .
  • Pull cover -3- as far as possible off padding -2-.
  • Using commercially available pliers, open upholstery clips -1-.
  • Separate cover -3- from padding -2-.
Volkswagen ID.4. Separating rear bench seat cover from padding

Installing

Install in reverse order of removal, observing the following:

  • Secure upholstery clips in sequence -1- through -27- using upholstery clip pliers - V.A.G 1634B- .
  • Make sure that the cover is fitted without creases.
Volkswagen ID.4. Separating rear bench seat cover from padding

Separating rear seat backrest cover from padding

Special tools and workshop equipment required

  • upholstery clip pliers - V.A.G 1634BID

Removing

  • Remove cover and padding of rear seat backrest ⇒ Rep. gr. 74 ; Removing and installing cover and padding of rear seat backrest .
  • Pull cover -1- off padding -3-.
  • Using commercially available pliers, open upholstery clips -2-.
  • Remove cover -1- from padding -3-.
Volkswagen ID.4. Separating rear seat backrest cover from padding

Installing

Install in reverse order of removal, observing the following:

  • Secure upholstery clips in sequence -1- through -11- using upholstery clip pliers - V.A.G 1634B- .
  • Rear seat backrest without load-through hatch: secure upholstery clips -12- through -15-.
  • Make sure that the cover is fitted without creases.
Volkswagen ID.4. Separating rear seat backrest cover from padding