Mouldings, trims, extensions

In this manual: Mouldings, trims, extensions
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
10steps
~60min
3/5difficulty
0102030405021N·mlb·ft
Tightening torque found on this page
Done 0 of 10
  • Assembly overview - covers
  • Assembly overview - side member trim
  • Assembly overview - C-pillar trim
  • Removing and installing step moulding
  • Removing and installing side member trim
  • Removing and installing retaining strip
  • Removing and installing A-pillar cover
  • Removing and installing B-pillar trim on door
  • Removing and installing trim panel for C-pillar
  • Removing and installing front wheel arch cover
  • Removing and installing wing cover
  • Removing and installing rear wheel arch cover
  • Removing and installing trim cover for front door
  • Removing and installing trim cover for rear door
  • Removing and installing trim cover for rear door, GTX

Assembly overview - covers

Overview is shown for left side of vehicle as an example

  1. Front door moulding
  • Renew after removing
  • ⇒ "3.18 Removing and installing trim cover for front door"
  1. Bonding surface
  2. Adhesive tape
  3. Clip
  • Qty. 3
  1. Centring pin
  • Qty. 2
  1. Trim cover for rear door
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing trim cover for rear door
  1. Clip
  • Qty. 5
  1. Centring pin
  • Qty. 3
Volkswagen ID.4. Assembly overview - covers

Assembly overview - step moulding

Overview is shown for left side of vehicle as an example

  1. Step moulding
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing step moulding
  1. Outer side member
  2. Double-sided adhesive tape
  3. Bonding surface
    Volkswagen ID.4. Assembly overview - step moulding

Assembly overview - side member trim

The assembly overview here applies to the left side of the vehicle.

  1. Side member trim
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing side member trim
  1. Adhesive tape
  2. Bolt
  • 7x
  • 2 N·m
  1. Clip
  • 5x
  1. Grommet
  • Depending on equipment/ vehicle version
  • 5x
  1. Expanding nut
  • At front and rear.
  • 2x
  1. Expanding nut
  • 4x
Volkswagen ID.4. Assembly overview - side member trim

Assembly overview - water deflector strip

Overview is shown for right side of vehicle as an example

  1. Water deflector
  • ⇒ Rep. gr. 66 ; Removing and installing water deflector strip
  1. A-pillar
  2. Pop rivet
  • Quantity and position depending on model
  • Qty. 5 or 6
  1. Retaining strip
  • ⇒ Rep. gr. 66 ; Removing and installing retaining strip
Volkswagen ID.4. Assembly overview - water deflector strip

Assembly overview - C-pillar trim

The overview is shown for the left side of the vehicle as an example.

  1. C-pillar trim
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing trim panel for C-pillar
  1. Adhesive tape
  • Can only be renewed along with C-pillar trim
  1. Clip
  • Can only be renewed along with C-pillar trim
  • Qty. 8
  1. Seal
  • Can only be renewed along with C-pillar trim
  1. C-pillar
Volkswagen ID.4. Assembly overview - C-pillar trim

Assembly overview - wheel arch covers

The overview is shown for the left side of the vehicle as an example.

  1. Front wheel arch cover
  • Depending on equipment/ version
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing front wheel arch cover
  1. Clip
  • Qty. 10
  1. Foam tape
  • Renew only with front wheel arch cover
  1. Adhesive tape
  • Renew only with front wheel arch cover
  1. Wing cover
  • Depending on equipment/ version
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Mouldings, trims, extensions; Removing and installing wing cover
  1. Adhesive tape
  • Renew only with wing cover
  1. Front wheel arch cover
  • Depending on equipment/ version
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing front wheel arch cover
  1. Bolt
  • 2 N·m
  1. Locking lug
  • Renew only with front wheel arch cover
  • Qty. 4
  1. Foam tape
  • Renew only with rear wheel arch cover
  1. Clip
  • Qty. 9
  1. Rear wheel arch cover
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing rear wheel arch cover
  1. Locking lug
  • Renew only with rear wheel arch cover
  • Qty. 4
  1. Bolt
  • 2 N·m
Volkswagen ID.4. Assembly overview - wheel arch covers

Removing and installing step moulding

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-
  • roller - T40400-

Removal and installation are described for left side of vehicle as an example.

Important

  • Observe specifications with regard to temperature, minimum curing period, removal of adhesive residue and cleaning ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .

Removing

  • Apply heat from hot air blower - V.A.G 1416- to step moulding -1- in area of adhesive strip.
  • Pull step moulding -1- off outer side member -2-.
Volkswagen ID.4. Removing and installing step moulding

Installing

Install in reverse order of removal, observing the following:

  • Remove adhesive residue and clean bonding surface.
  • Align step moulding -1-:
  • Dimension -a- = 175 mm
  • Dimension -b- = 7 mm
  • Pull off protective film of step moulding -1-.
  • Press step moulding -1- onto outer side member -2- from front to rear with a force of 45 N.
  • Use roller - T40400- in area of adhesive strip to press on step moulding -1- with a force of 45 N.

Important

  • Roll on outer area of step moulding -1- first and then inner area.
  • The minimum drying time must be adhered to.
Volkswagen ID.4. Removing and installing step moulding

Removing and installing side member trim

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-
  • roller - T40400-

Removal and installation are described for left side of vehicle as an example.

Important

  • Observe specifications with regard to temperature, minimum curing period, removal of adhesive residue and cleaning ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components

Removing

  • Remove front wheel arc cover ⇒ Rep. gr. 66 ; Removing and installing front wheel arch cover .
  • Remove rear wheel arch cover ⇒ Rep. gr. 66 ; Removing and installing rear wheel arch cover .
  • Unscrew bolts -3- from side member trim -1-.
  • Use hot air blower - V.A.G 1416- to heat up side member trim -1- in area of bonding surface -2- prior to removal.
  • Insert commercially available plastic wedge between outer side member and side member trim -1-.
  • As soon as bonded joint is detached, pull side member trim -1- with clips -4- and their respective grommets -5- out of outer side member.
Volkswagen ID.4. Removing and installing side member trim

Installing

Install in reverse order of removal, observing the following:

  • Remove adhesive residue and clean bonding surfaces ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .
  • Position side member trim -1- on outer side member.
  • Screw in bolt -6-.
  • Press side member trim -1- with clips -4- and their corresponding grommets -5- into outer side member.
  • Align side member trim -1- longitudinally.
  • Use removal aid to pull protective film off double-sided adhesive tape -2- upwards and towards rear.
  • Press on side member trim -1- evenly in area of adhesive tape.
  • Use roller - T40400- in area of adhesive tape to press on side member trim -1- with a force of 50 N to 70 N.

Important

  • The minimum drying time must be adhered to.
  • Tighten bolt -6-.
  • Tighten bolts -3-.
Volkswagen ID.4. Removing and installing side member trim

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - side member trim

Removing and installing water deflector strip

Removal and installation are described for the right vehicle side as an example.

Removing

  • Starting at bottom, pull water deflector strip -1- out of retaining strip -2-.
Volkswagen ID.4. Removing and installing water deflector strip

Installing

Install in reverse order of removal, observing the following:

  • Position upper inner edge of water deflector -1- on upper edge of windscreen.
  • Press water deflector strip -1- from above into retaining strip -2-.

Important

  • Water deflector strip -1- must engage in clips.
Volkswagen ID.4. Removing and installing water deflector strip

Removing and installing retaining strip

Special tools and workshop equipment required

  • Drill, commercially available
  • drill bit, 4 mm in dia., commercially available
  • pop rivet pliers, commercially available

Removal and installation are described for the right side of vehicle as an example.

The retaining strip may be split in two parts, depending on the equipment/version.

The number of blind rivets differs, depending on the equipment/ version.

Removing

  • Remove water deflector strip ⇒ Rep. gr. 66 ; Removing and installing water deflector strip .
  • Remove windscreen ⇒ Rep. gr. 64 ; Removing and installing windscreen .

CAUTION

Risk of injury caused by flying metal shavings.

Eyes and skin can suffer irritation or injuries.

  • Put on safety goggles.
  • Put on protective gloves.

NOTICE

Risk of corrosion damage due to swarf and paint damage

  • Remove any swarf.
  • Immediately repair any damage to paintwork.
  • Drill out pop rivets -arrows- and remove retaining strip -1-.
Volkswagen ID.4. Removing and installing retaining strip

Installing

Install in reverse order of removal, observing the following:

Note

The left and right retaining strips are not identical.

  • Rivet retaining strip starting at top.

Removing and installing A-pillar cover

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-

Removal and installation are described for the left side of vehicle as an example.

Important

  • Instructions and specifications regarding temperature, minimum drying time, removal of adhesive residue and cleaning must be adhered to ⇒ General information - body; Rep.

    gr. 52 ; Self-adhesive components; Specifications for selfadhesive components .

Removing

  • Remove water deflector strip ⇒ Rep. gr. 66 ; Removing and installing water deflector strip .
  • Apply heat from hot air blower - V.A.G 1416- to A-pillar cover -1- in area of adhesive tape -2-.
  • Apply commercially available plastic wedge in direction of -arrow A- between A-pillar -3- and A-pillar cover -1-.
  • When bonded joint becomes detach, remove A-pillar cover -1- in direction of -arrow B- from A-pillar -3-.
Volkswagen ID.4. Removing and installing A-pillar cover

Installing

Install in reverse order of removal, observing the following:

  • Remove adhesive residue, and clean bonding surface -2- ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .
Volkswagen ID.4. Removing and installing A-pillar cover
  • Align A-pillar cover -1- with roof frame strip and embossing in A-pillar in direction of -arrow A-.
  • Pull protective film off A-pillar cover -1-.
  • Align A-pillar cover -1- with A-pillar -3-, and press it on.
  • Press on A-pillar cover -1- in area of adhesive tape applying a force of 50 N.

Important

  • The minimum drying time must be adhered to.
Volkswagen ID.4. Removing and installing A-pillar cover

Removing and installing trim panel for A-pillar

Removal and installation are described for left side of vehicle as an example.

Removing

  • Use commercially available plastic wedge to lever A-pillar trim -1- off grommets -2-.
Volkswagen ID.4. Removing and installing trim panel for A-pillar

Installing

Install in reverse order of removal, observing the following:

  • Push A-pillar trim -1- with securing pins -2- onto spreader rivets -3-.
Volkswagen ID.4. Removing and installing trim panel for A-pillar

Removing and installing B-pillar trim on door

Removing and installing B-pillar trim onf ront door

Removal and installation are described for left side of vehicle as an example.

Removing

  • Lower front door window completely.
  • Remove outer window slot seal ⇒ Rep. gr. 57 ; Removing and installing outer window slot seal .
  • Pull window channel -1- in area of B-pillar trim on front door -2- in direction of -arrow A- out of front door -4-.
  • Unscrew bolts -3- from spreader rivets, and unclip spreader rivets.
  • Push B-pillar trim on front door -2- in direction of -arrow B-, and pull it off at top in direction of -arrow C- until guide hooks -5- are released from front door -4-.
  • Pull B-pillar trim on front door -2- in direction of -arrow D- out of front door -4-
Volkswagen ID.4. Removing and installing B-pillar trim on door

Installing

Install in reverse order of removal, observing the following:

  • Guide B-pillar trim on front door -2- in direction of -arrow Ainto window slot of front door -4-.
  • Push B-pillar trim on front door -2- in direction of -arrow Bagainst front door -4- and in direction of -arrow C- until guide hooks -5- engage in front door -4-.
  • Press in bolts with spreader rivets -3-.
  • Insert window channel -1- in direction of -arrow D- in B-pillar trim on front door -2-.
Volkswagen ID.4. Removing and installing B-pillar trim on door

Removing and installing B-pillar trim on rear door

Removal and installation are described for left side of vehicle as an example.

Removing

  • Lower rear door window completely.
  • Remove outer window slot seal ⇒ Rep. gr. 58 ; Removing and installing outer window slot seal .
  • Pull out window channel -2- in area of B-pillar trim on rear door -1- in direction of -arrow A- and -arrow B-.
  • Unscrew bolts -3- from spreader rivets, and unclip spreader rivets.
  • Push B-pillar trim on rear door -1- in direction of -arrow C-, and pull it off in direction of -arrow D - until guide hooks -4- are released from window frame.
  • Pull out B-pillar trim on rear door -1- in direction of -arrow E-.
Volkswagen ID.4. Removing and installing B-pillar trim on rear door

Installing

Install in reverse order of removal, observing the following:

  • Fit B-pillar trim on rear door -1- in direction of -arrow A- to window frame.
  • Guide B-pillar trim on rear door -1- in direction of -arrow Binto window slot.
  • Push B-pillar trim on rear door -1- in direction of -arrow Cuntil guide hooks -4- engage in window frame.
  • Press in bolts with spreader rivets -3-.
  • Insert window channel -2- in direction of -arrow D- and -arrow E- in B-pillar trim on rear door -1-.
Volkswagen ID.4. Removing and installing B-pillar trim on rear door

Removing and installing trim panel for C-pillar

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-
  • roller - T40400-
  • wedge - T10383-

Removal and installation are described for the left side of vehicle as an example.

Important

  • Instructions and specifications regarding temperature, minimum drying time, removal of adhesive residue and cleaning must be adhered to ⇒ General information - body; Rep.

    gr. 52 ; Self-adhesive components; Specifications for selfadhesive components .

Removing

  • Apply heat from hot air blower - V.A.G 1416- to C-pillar trim -1- in area of adhesive tape -3-.
  • Detach clips -4- using wedge - T10383- -2-.
Volkswagen ID.4. Removing and installing trim panel for C-pillar

Installing

Install in reverse order of removal, observing the following

  • Remove adhesive residue, and clean bonding surface ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .
  • Guide C-pillar trim -1- in direction of -arrow A- in roof trim strip -3-.
  • Align clips of C-pillar trim -1- on C-pillar -2-.
Volkswagen ID.4. Removing and installing trim panel for C-pillar
  • Push on C-pillar trim -1- until clips can be heard to engage.
  • Roll on C-pillar trim -1- in area of adhesive tape -3- at a force of between 50 N and 70 N using roller - T40400- -2- in direction of -arrow-.

Important

  • The minimum drying time must be adhered to.
Volkswagen ID.4. Removing and installing trim panel for C-pillar

Removing and installing front wheel arch cover

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-
  • removal wedge set - VAS 895 015-
  • roller - T40400-

Removal and installation are described for left side of vehicle as an example.

Important

  • Observe specifications with regard to temperature, minimum curing period, removal of adhesive residue and cleaning ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .

Removing

  • Detach front wheel housing liner in area of wing ⇒ Rep.

    gr. 66 ; Removing and installing front wheel housing liner .

Vehicles with wing cover:

  • Remove wing cover ⇒ "3.16.1 Removing and installing wing cover"

All vehicles (continued)

Vehicles without wing cover:

  • Apply heat from hot air blower - V.A.G 1416- to front wheel arch cover in area of adhesive strip -5-.
Volkswagen ID.4. Removing and installing front wheel arch cover

All vehicles (continued)

  • Unscrew bolt -2-.
  • Release locking devices -3-, and pull out of bumper cover in direction of -arrow A-.

NOTICE

Risk of damage to component surfaces.

  • When using a lever, mask visible areas of the component with commercially available adhesive tape.
  • Use wedge no. 24 from removal wedge set - VAS 895 015- to press together clips -4- -arrows B-.
  • Pull front wheel arch cover -1- in direction of -arrow C- off wing.
Volkswagen ID.4. Removing and installing front wheel arch cover

Installing

Install in reverse order of removal, observing the following:

  • Remove adhesive residue and clean bonding surfaces ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components
  • Use removal aids to pull protective foil -5- off adhesive tape -6-.
  • Guide in front wheel arch cover -1- -arrow C-.
  • Engage clips -4- of front wheel arch cover -1- in wing -arrow B-.
  • Engage locking devices -3- of front wheel arch cover -1- in bumper cover -arrow A-.
  • Press on front wheel arch cover in direction of -arrow A-.
  • Use roller - T40400- to press on front wheel arch cover in area of adhesive strip at a force of between 50 N and 70 N.

Important

  • The minimum drying time must be adhered to.
  • Tighten bolts securing front wheel arch cover on bumper.
Volkswagen ID.4. Removing and installing front wheel arch cover

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - wheel arch covers

Removing and installing wing cover

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-
  • roller - T40400-

Removal and installation are described for the left side of vehicle as an example.

Wing cover is referred to hereafter as cover.

Important

  • Instructions and specifications regarding temperature, minimum drying time, removal of adhesive residue and cleaning must be adhered to ⇒ General information - body; Rep.

    gr. 52 ; Self-adhesive components; Specifications for selfadhesive components .

Removing

  • Apply heat from hot air blower - V.A.G 1416- to cover -3- in area of adhesive strips -2-.
  • Lever off cover -3- using commercially available plastic wedge and pull off.
Volkswagen ID.4. Removing and installing wing cover

Installing

  • Remove adhesive residue, and clean bonding surface ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .
  • Use removal aids to pull protective foil off adhesive tape -2-.
  • Align cover -3- with aid of pins -arrows-.
  • Press cover -3- onto wing and wheel arch trim -1-.
  • Using roller - T40400- , press on cover in area of adhesive strips at a force of between 50 N and 70 N.

Important

  • The minimum drying time must be adhered to
Volkswagen ID.4. Removing and installing wing cover

Removing and installing rear wheel arch cover

Special tools and workshop equipment required

  • removal wedge set - VAS 895 015-

Removal and installation are described for left side of vehicle as an example.

Removing

  • Detach rear wheel housing liner in area of side panel ⇒ Rep. gr. 66 ; Removing and installing rear wheel housing liner .

Vehicles with bolt in wheel arch cover in area of side member:

  • Unscrew bolt -5-.
Volkswagen ID.4. Removing and installing rear wheel arch cover

All vehicles (continued)

  • Unscrew bolt -4-.
  • Press together locking devices -6- in direction of -arrow A-. While doing this, pull rear wheel arch cover in -direction of arrow B- out of bumper cover.

NOTICE

Risk of damage to component surfaces.

  • When using a lever, mask visible areas of the component with commercially available adhesive tape.
  • Use wedge no. 24 from removal wedge set - VAS 895 015- to press together clips -2- in direction of -arrow C-. While doing this, pull off rear wheel arch cover in direction of -arrow B-.
  • Pull off rear wheel arch cover -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing rear wheel arch cover

Installing

Install in reverse order of removal, observing the following:

Important

  • Make sure that clips -4- are in correct position.
  • Engage clips -4- of rear wheel arch cover -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing rear wheel arch cover

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - wheel arch covers

Removing and installing trim cover for front door

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-
  • roller - T40400-

Removal and installation are described for left side of vehicle as an example.

The trim cover for front door will henceforth be referred to as "cover".

Important

  • Observe specifications with regard to temperature, minimum curing period, removal of adhesive residue and cleaning ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .

Removing

  • Apply heat from hot air blower - V.A.G 1416- to cover -3- in area of bonding surfaces.
  • Use commercially available plastic wedge -1- to lever cover -3- in direction of -arrow- off door -2-.
Volkswagen ID.4. Removing and installing trim cover for front door

Installing

Install in reverse order of removal, observing the following:

  • Remove adhesive residue, and clean bonding surfaces.
  • Use removal aid to pull protective backing off adhesive tape -2- and -3-.
Volkswagen ID.4. Removing and installing trim cover for front door

Important

  • Following sequence must be observed: first hook cover into bottom of door, then align it with central centring pin and then with outer centring pins.
  • Hook cover -1- into bottom of door -5-, and align it with centring pins -4-.

Important

  • Following sequence must be observed: first press on cover at central centring pin and then at outer centring pins.
  • Press on cover -1- until it can be heard to enga
  • Use roller - T40400- to press on cover -1- with a force of between 50 N and 70 N in area of bonding surfaces.

Important

  • The minimum drying time must be adhered to.

Removing and installing trim cover for rear door

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-
  • roller - T40400-

Removal and installation are described for left side of vehicle as an example.

The trim cover for rear door will henceforth be referred to as "cover".

Important

  • Observe specifications with regard to temperature, minimum curing period, removal of adhesive residue and cleaning ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .

Removing

  • Apply heat from hot air blower - V.A.G 1416- to cover -3- in area of adhesive strips.
  • Use commercially available plastic wedge -2- to lever cover -3- in direction of -arrow- off door -1-.
Volkswagen ID.4. Removing and installing trim cover for rear door

Installing

Install in reverse order of removal, observing the following:

  • Remove adhesive residue, and clean bonding surfaces.
  • Use removal aid to pull protective backing off adhesive tape -2- and -4-.

Important

  • Following sequence must be observed: first hook cover into bottom of door, then align it with central centring pin and then with outer centring pins.
  • Hook cover -1- into bottom of door -5-, and align it with centring pins -3-.

Important

  • Following sequence must be observed: first hook cover into bottom of door, then press on at central centring pin and then at outer centring pins.
  • Press on cover -1- until it can be heard to engage.
  • Use roller - T40400- to press on cover -1- in area of adhesive strips at a force of between 50 N and 70 N.

Important

  • The minimum drying time must be adhered to.
Volkswagen ID.4. Removing and installing trim cover for rear door

Removing and installing trim cover for rear door, GTX

Removing and installing trim cover for rear door

Special tools and workshop equipment required

  • hot air blower - V.A.G 1416-
  • roller - T40400-

Removal and installation are described for left side of vehicle as an example.

The trim cover for rear door will henceforth be referred to as "cover".

Important

  • Observe specifications with regard to temperature, minimum curing period, removal of adhesive residue and cleaning ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .

Removing

  • Apply heat from hot air blower - V.A.G 1416- to cover -3- in area of adhesive strip.
  • Use commercially available plastic wedge -2- to lever cover -3- in direction of -arrow A- off door -1-.
  • Remove cover -3- from door -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing trim cover for rear door, GTX

Installing

  • Remove adhesive residue, and clean bonding surfaces.
  • Use removal aid to pull protective backing off adhesive tape -2- and -3-.

Important

  • Following sequence must be observed: first hook cover into bottom of door, then align it with central centring pin and then with outer centring pins.
  • Hook cover -1- into bottom of door -4- in direction of -arrow A-, and align it with centring pins -arrows-.

Important

  • Following sequence must be observed: first hook cover into bottom of door, then press on at central centring pin and then at outer centring pins.
  • Press on cover -1- until it can be heard to engage.
  • Use roller - T40400- to press on cover -1- in area of adhesive strips at a force of between 50 N and 70 N.

Important

  • The minimum drying time must be adhered to.
Volkswagen ID.4. Removing and installing trim cover for rear door, GTX