Exterior mirror

In this manual: Exterior mirror
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~8min read
010203040500.81N·mlb·ft
Tightening torque found on this page
  • Assembly overview - exterior mirror
  • Removing and installing exterior mirror [VX4]/[VX5]
  • Removing and installing mirror glass
  • Removing and installing mirror adjustment unit
  • Removing and installing lower mirror cover
  • Removing and installing mirror trim

Assembly overview - exterior mirror

Overview shown for left side of vehicle as an example

Volkswagen ID.4. Assembly overview - exterior mirror
  1. Upper mirror cover
  • ⇒ Rep. gr. 66 ; Removing and installing upper mirror cover
  1. Lane change assist warning lamp in left exterior mirror - K312- / lane change assist warning lamp in right exterior mirror - K311-
  • Depending on equipment/ version
  • ⇒ Driver assist systems; Rep.

    gr. 98 ; Senders/sensors/ control units; Removing and installing lane change assist warning lamp in exterior mirror [K311]/[K312]

  1. Bolt
  • Fitted on selected models
  • 0,8 N·m
  1. Mirror mounting
  • One-piece design with mirror cover at bottom
  • With driver side exterior mirror - VX4- / passenger side exterior mirror - VX5-
  • ⇒ Rep. gr. 66 ; Removing and installing exterior mirror [VX4]/ [VX5] 5 - Bolt
  • Quantity varies depending on model
  • Qty. 1, 2 or 3
  • M6 or M8
  • M6 9 N·m
  • M8 20 N·m
  1. Cover
  • Fitted on selected models
  • Quantity and shape vary depending on model
  • Qty. 1 or 3
  1. Mirror trim
  • ⇒ Rep. gr. 66 ; Removing and installing mirror trim
  1. Bolt
  • Qty. 2
  • 0,8 N·m
  1. Mirror glass
  • With heated exterior mirror on driver side - Z4- and heated exterior mirror on passenger side - Z5- , depending on equipment/version
  • ⇒ Rep. gr. 66 ; Removing and installing mirror glass
  1. Lower mirror cover
  • One-piece design with mirror mounting, depending on model
  • ⇒ Rep. gr. 66 ; Exterior mirror; Removing and installing lower mirror cover
  1. Entry light in exterior mirror, driver side - W52- / entry light in exterior mirror, passenger side - W53-
  • Depending on equipment/version
  • ⇒ Electrical system; Rep. gr. 94 ; Lights in exterior mirror; Removing and installing entry light in exterior mirror [W52]/[W53]
  1. Bolt
  • Depending on equipment/version
  • Quantity varies depending on model
  • Qty. 1 or 2
  • 0,8 N·m
  1. Left overhead view camera - R244- / right overhead view camera - R245-
  • Depending on equipment/version
  • ⇒ Driver assist systems; Rep. gr. 98 ; Senders/sensors/control units; Removing and installing left/ right overhead view camera [R244]/[R245]
  1. Overhead view camera bracket
  • Depending on equipment/version
  1. Bolt
  • Depending on equipment/version
  • Qty. 2
  • 0,8 N·m
  1. Mirror adjustment unit
  • Driver side: with driver side mirror adjustment motor 2 - V17- , driver side mirror adjustment motor - V149- , driver side fold-in mirror motor - V121- and optionally with potentiometer for horizontal adjustment of driver side mirror - G514- and potentiometer for vertical adjustment of driver side mirror - G515-
  • Front passenger side: with front passenger side mirror adjustment motor 2 - V25- , front passenger side mirror adjustment motor - V150- , front passenger side fold-in mirror motor - V122- and optionally with potentiometer for horizontal adjustment of front passenger side mirror - G516- and potentiometer for vertical adjustment of front passenger side mirror - G517-
  • ⇒ Rep. gr. 66 ; Removing and installing mirror adjustment unit
  1. Bolt
  • 1,4 N·m
  1. Driver side turn signal repeater bulb in exterior mirror - L131- / passenger side turn signal repeater bulb in exterior mirror - L132-
  • ⇒ Electrical system; Rep. gr. 94 ; Lights in exterior mirror; Removing and installing turn signal repeater bulb [L131]/[L132]
  1. Bolt
  • Fitted on selected models
  • Qty. 2
  • 0,8 N·m

Removing and installing exterior mirror [VX4]/[VX5]

Driver side exterior mirror - VX4- and passenger side exterior mirror - VX5- are referred to hereafter as exterior mirror.

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove front door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Front door trims; Removing and installing front door trim .
  • Disconnect electrical connectors -3-.
  • Lever off cap -4-.
  • Unscrew bolt -5-.
  • Detach exterior mirror -1- in direction of -arrow A- while guiding grommet -6- with electrical wire in direction of -arrow Bout of door -2-.
Volkswagen ID.4. Removing and installing exterior mirror [VX4]/[VX5]

Installing

Install in reverse order of removal, observing the following:

  • Use an insertion aid to guide grommet with electrical wire into door.
  • Guide pin and clip of exterior mirror into corresponding holes in frame.

Vehicles with overhead view camera

If exterior mirror is renewed:

  • Calibrate overhead view camera ⇒ Driver assist systems; Rep. gr. 98 ; Overhead view camera; Calibrating overhead view camera system .

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - exterior mirror

Removing and installing mirror glass

Special tools and workshop equipment required

  • removal lever - 80-200-

Heated exterior mirror on driver side - Z4- and heated exterior mirror on passenger side - Z5- are referred to hereafter as mirror glass.

Removal and installation are described for left side of vehicle as an example.

Removing

CAUTION

Risk of injury to hands and eyes due to glass splinters.

Danger of cutting yourself.

  • Put on safety goggles.
  • Put on protective gloves.

NOTICE

Risk of damage to surfaces of components.

  • Before using a lever, always mask off the components installed in visible areas using commercially available adhesive tape.
  • Press bottom of mirror glass -1- into exterior mirror.
  • Use removal lever - 80-200- -4- to lever mirror glass -1- off mirror adjustment unit -2-.
  • Swing mirror glass -1- in direction of -arrow A-, and disconnect electrical connectors -3-.
Volkswagen ID.4. Removing and installing mirror glass

Installing

Install in reverse order of removal, observing the following:

CAUTION

Risk of injury to hands and eyes due to glass splinters.

Danger of cutting yourself.

  • Put on safety goggles.
  • Put on protective gloves.

NOTICE

Improper handling may cause damage to the mirror glass.

  • Only fit and press on the mirror glass centrally.
  • Push mirror glass centrally onto mirror adjustment unit until it can be heard to engage.

Removing and installing mirror adjustment unit

The removal and installation procedures are described for the left side of the vehicle as an example.

Removing

  • Remove mirror glass ⇒ Rep. gr. 66 ; Removing and installing mirror glass .
  • Unscrew bolt -3-, and remove mirror adjustment unit -1-.
  • Unplug electrical connector -2-
Volkswagen ID.4. Removing and installing mirror adjustment unit

Installing

Installation is carried out in reverse order; note the following:

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - exterior mirror

Removing and installing upper mirror cover

Removal and installation are described for left side of vehicle as an example.

The upper mirror cover will henceforth be referred to as "mirror cover".

Removing

  • Push mirror cover -1- in direction of -arrow A-, and pull it off mirror mounting in direction of -arrow B-.
Volkswagen ID.4. Removing and installing upper mirror cover

Vehicles with electrical connector on mirror cover

  • Disconnect electrical connector.

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

  • Push on mirror cover until locking devices can be heard to engage.

Removing and installing lower mirror cover

Removal and installation are described for the left vehicle side as an example.

Removing

  • Remove upper mirror cover ⇒ Rep. gr. 66 ; Removing and installing upper mirror cover .
  • Release locking devices -arrows-.
  • Remove lower mirror cover -1- in direction of -arrow A- from mirror mounting.
Volkswagen ID.4. Removing and installing lower mirror cover

Vehicles with left overhead view camera - R244-

  • Disconnect electrical connector for left overhead view camera - R244- .

All vehicles (continued)

Vehicles with entry light in exterior mirror, driver side - W52-

  • Disconnect electrical connector for entry light in exterior mirror, driver side - W52- .

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

  • Push on lower mirror cover until locking devices can be heard to engage.

Removing and installing mirror trim

Push on lower mirror cover until locking devices can be heard to engage.

Removing

  • Remove mirror glass ⇒ Rep. gr. 66 ; Removing and installing mirror glass .
  • Remove upper mirror cover ⇒ Rep. gr. 66 ; Removing and installing upper mirror cover .

Vehicles with 1 fastener in mirror trim:

  • Unscrew bolts -2-.
  • Press together fasteners -3- in direction of -arrow A-, and release them.
  • Pull off mirror trim -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing mirror trim

All vehicles (continued)

Vehicles with 2 fasteners in mirror trim:

  • Unscrew bolts -2-.
  • Press together fasteners -3- in direction of -arrow A-, and release them.
  • Pull off mirror trim -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing mirror trim

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

  • Fit mirror trim so that locking devices can be heard to engage.

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - exterior mirror