Door windows

In this manual: Door windows
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
6steps
~36min
2/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 6
  • Assembly overview - rear door window
  • Removing and installing rear door window
  • Removing and installing front door window
  • Removing and installing rear door window
  • Removing and installing fixed rear door window

Assembly overview - rear door window

Overview shown for left side of vehicle as an example

  1. Front door window
  • ⇒ Rep. gr. 64 ; Removing and installing front door window
  1. Door subframe
  • ⇒ Rep. gr. 57 ; Assembly overview - assembly carrier
  • ⇒ Rep. gr. 57 ; Removing and installing assembly carrier
  1. Cover
  • Qty. 2
  1. Clamping bracket
  • Qty. 2
Volkswagen ID.4. Assembly overview - rear door window

Assembly overview - fixed rear door window

The overview is shown for the left side of vehicle as an example.

  1. Fixed front door window
  • ⇒ Rep. gr. 64 ; Removing and installing fixed front door window
  1. Bolt
  • 8 N·m
  1. Cap
  2. Clip
  • Qty. 2
Volkswagen ID.4. Assembly overview - fixed rear door window

Removing and installing rear door window

Overview shown for left side of vehicle as an example

  1. Rear door window
  • ⇒ Rep. gr. 64 ; Removing and installing rear door window
  1. Door subframe
  • ⇒ Rep. gr. 58 ; Assembly overview - assembly carrier
  • ⇒ Rep. gr. 58 ; Removing and installing assembly carrier
  1. Spreader rivet
  • Depending on equipment/ version
  1. Spreader plug
  • Depending on equipment/ version
  1. Cover
  2. Window regulator guide
  • Depending on equipment/ version
Volkswagen ID.4. Removing and installing rear door window

Assembly overview - fixed rear door window

Overview shown for left side of vehicle as an example

  1. Fixed rear door window
  • ⇒ Rep. gr. 64 ; Removing and installing fixed rear door window
  1. Clip
  • Qty. 3
  1. Rear door
  2. Bolt
  • 8 N·m
  1. Cap
Volkswagen ID.4. Assembly overview - fixed rear door window

Removing and installing front door window

Removal and installation are described for left side of vehicle as an example.

The assembly carrier will henceforth be referred to as "carrier".

Carrier design Front door window is referred to hereafter as door window.

Driver side window regulator motor - V147- / front passenger side window regulator motor - V148- is referred to hereafter as window regulator motor.

Removing

  • Remove front door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Front door trims; Removing and installing front door trim .

If window regulator cannot be operated:

  • Remove window regulator motor ⇒ Rep. gr. 57 ; Removing and installing window regulator motor [V147]/[V148] .
  • Push door window -1- to required position.

All vehicles (continued)

Important

  • Make sure to adhere to the following sequence: Release locking devices in area of B-pillar first, then proceed with locking devices in area of A-pillar.
  • Lever out caps -3- from carrier -2- using commercially available plastic wedge.
  • Lower door window -1- until clamping jaws of carrier -5- become accessible through opening in carrier -2-.

Note

The plastic shaft of the electrician's screwdriver protects the door window from damage.

  • Guide commercially available electrician's screwdriver -4- through openings in carrier -2- and door window -1- towards clamping jaw of carrier -5-.
  • Push commercially available electrician's screwdriver in direction of -arrow A- into locking devices of clamping jaws to release locking devices.
  • To ensure that door window -1- does not fall back into locking devices, raise door window -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing front door window
  • Pull door window -1- upwards out of clamping jaws of carrier -3-.
  • Lift door window -1- at rear, and swing it out of window guide -2- in direction of -arrow-.
Volkswagen ID.4. Removing and installing front door window

Installing

Install in reverse order of removal, observing the following:

  • Swing door window -1- in direction of -arrow- into window guide -2-.

Important

  • Make sure that door window -1- is properly inserted into window guide -2-
  • Guide door window -1- without force into clamping jaws of carrier.
  • Align door window -1- with rear window frame.
Volkswagen ID.4. Removing and installing front door window

Important

  • Make sure to adhere to the following sequence: Engage locking devices in area of B-pillar first, then proceed with locking devices in area of A-pillar.
  • Push door window -1- into clamping jaws of carrier -2- until door window -1- can be heard to engage.
Volkswagen ID.4. Removing and installing front door window
  • Test function before installing the front door trim.

Removing and installing rear door window

Special tools and workshop equipment required

  • release tool - T10615-

Removal and installation are described for left side of vehicle as an example.

The assembly carrier will henceforth be referred to as "carrier".

Rear door window is referred to hereafter as door window.

Rear driver side window regulator motor - V471- / rear passenger side window regulator motor - V472- is referred to hereafter as window regulator motor.

Removing

  • Remove rear door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Rear door trim; Removing and installing rear door trim .
  • Remove B-pillar trim on rear door ⇒ "3.13.2 Removing and installing B-pillar trim on rear door"

If power window cannot be operated

  • Remove window regulator motor ⇒ Rep. gr. 58 ; Removing and installing rear window regulator motor [V471]/[V472]
  • Push door window -1- to required position.

All vehicles (continued)

  • Lever out cap -5- from carrier -2- using commercially available plastic wedge.
  • Lower door window -1- until spreader rivet -3- and spreader plug -4- are accessible through opening in carrier -2-.
  • Pull out spreader rivet -3- from spreader plug -4- using release tool - T10615- .
  • Pull out spreader plug -4- from window channel -6- using release tool - T10615- , making sure that spreader plug -4- does not drop into door.
Volkswagen ID.4. Removing and installing rear door window
  • Pull front section of window channel -2- out of mounting.
  • Pull door window -1- in direction of -arrow- towards vehicle exterior and out of window slot.
Volkswagen ID.4. Removing and installing rear door window

Installing

Install in reverse order of removal, observing the following:

  • With door window -1- removed, insert spreader plug -4- making sure it is centred properly.
  • Press spreader rivet -3- into spreader plug -4- so it is flush.
  • Insert door window -1- in direction of -arrow- into door, and push it into slot of window regulator guide.
  • Press door window -1- into window regulator guide -2- until door window -1- engages audibly.
Volkswagen ID.4. Removing and installing rear door window
  • Test function before installing the rear door trim.

Removing and installing fixed rear door window

Special tools and workshop equipment required

  • release tool - T10236-

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove rear door trim ⇒ General body repairs; interior; Rep. gr. 70 ; Rear door trims; Removing and installing rear door trim .
  • Remove window channel ⇒ Rep. gr. 58 ; Removing and installing window channel .
  • Lever off cap -7-.
  • Unscrew bolt -6-.
  • Pull seal -2- of fixed rear door window -1- off door flange.
  • Push fixed rear door window -1- slightly in direction of -arrow A-, and use release tool - T10236- -3- to unclip clips -5- one after the other.
  • Pull fixed rear door window -1- in direction of -arrow B- out of door -4-.
Volkswagen ID.4. Removing and installing fixed rear door window

Installing

Install in reverse order of removal, observing the following:

  • Guide fixed rear door window -1- with web in direction of -arrow A- into door -4-.
  • Push fixed rear door window -1- in direction of -arrow Bagainst door -4- until clips -2- can be heard to engage.
  • Tighten bolt -5-.
  • Press seal -3- onto door flange all around.
  • Fit cap -6-.
Volkswagen ID.4. Removing and installing fixed rear door window

Tightening torques

  • ⇒ Rep. gr. 64 ; Assembly overview - fixed rear door window