Components/control units

In this manual: Components/control units
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~16min read
  • Removing and installing control unit for front display and information control panel [J685]
  • Control unit 1 for information electronics [J794]
  • Removing and installing front bass loudspeakers
  • Removing and installing rear bass loudspeakers
  • Removing and installing digital sound package control unit [J525]
  • Removing and installing frequency modulation (FM) frequency filters [R178]/[R179]
  • Removing and installing LTE aerial
  • Removing and installing aerial amplifier for mobile telephone [R86]
  • Removing and installing multifunction buttons [E440]/[E441]
  • Removing and installing control unit for steering wheel contact detection [J1158]
  • Removing and installing emergency call module control unit and communication unit [J949], rear bench seat
  • Removing and installing loudspeaker for emergency call module [R335]
  • Removing and installing emergency battery, telematics [A16]

Removing and installing control unit for front display and information control panel [J685]

Removing

The control unit 1 for information electronics - J794- will henceforth be referred to as "information electronics control unit".

Removal and installation are described for a left-hand drive vehicle as an example.

If the control unit for information electronics is renewed, perform the test plan for the renewal of the control unit:

  • Carry out function "Renew control unit for information electronics" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Remove glove compartment cover ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment cover .
  • Release locking devices -arrows-, and pull out information electronics control unit -1- while at the same time swivelling it downwards.
  • Disconnect electrical connectors.
Volkswagen ID.4. Removing and installing control unit for front display and information control panel [J685]

Installing

Install in the reverse order of removal, observing the following:

Important

  • The information electronics control unit must engage audibly.

If the control unit for information electronics has been renewed, conclude the test plan for the renewal of the control unit:

  • Conclude function "Renew control unit for information electronics" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Control unit 1 for information electronics [J794]

Removing

The bracket for the control unit 1 for information electronics - J794- will henceforth be referred to as "bracket".

Removal and installation are described for a left-hand drive vehicle as an example.

  • Remove footwell vent on front passenger side ⇒ Heating, air conditioning; Rep. gr. 87 ; Air duct; Removing and installing footwell vent on front passenger side .
  • Remove dash panel trim on front passenger side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing dash panel trim on front passenger side .
  • Unscrew bolts -2- and -3-.
  • Detach strut -1-.
Volkswagen ID.4. Control unit 1 for information electronics [J794]
  • Remove control unit 1 for information electronics - J794- ⇒ Rep. gr. 91 ; Removing and installing control unit 1 for information electronics [J794] .
  • Remove heater and air conditioning system control unit - J979- ⇒ Heating, air conditioning system; Rep. gr. 87 ; Other control components; Removing and installing heater and air conditioning system control unit [J979] .
  • Remove data bus diagnostic interface - J533- ⇒ Electrical system; Rep. gr. 97 ; Control units; Removing and installing data bus diagnostic interface [J533] .
  • Loosen fan for control unit - V274- , and lay it aside with electrical wiring still connected ⇒ Electrical system; Rep.

    gr. 97 ; Control units; Removing and installing fan for control unit [V274] .

  • Pull out bracket -1- in direction of -arrow-, and detach it.
Volkswagen ID.4. Control unit 1 for information electronics [J794]

Installing

Install in the reverse order of removal, observing the following:

Tightening torques

  • ⇒ General body repairs, interior; Rep. gr. 70 ; Central tube for dash panel; Assembly overview - central tube for dash panel

Removing and installing front treble loudspeakers [R20]/[R22]

Front left treble loudspeaker - R20- / front right treble loudspeaker - R22- are removed and installed together with upper A-pillar trim.

  • Removing and installing upper A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing upper A-pillar trim .

Removing and installing front bass loudspeakers

Special tools and workshop equipment required

  • Drill, commercially available
  • pop rivet pliers, commercially available
  • suitable drill bit approx. 4 mm, commercially available

Removing

  • Remove front door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Front door trims; Removing and installing front door trim .
  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing and installing front bass loudspeakers

CAUTION

Risk of eye injuries due to metal swarf.

Eye irritation and injury possible.

  • Put on safety goggles.

NOTICE

Corrosion damage due to swarf and damaged paintwork

  • Completely remove swarf from the door, and immediately rectify any paintwork damage caused.
  • Drill out pop rivets -3-, and remove loudspeaker -1-.

Installing

Install in the reverse order of removal, observing the following:

Important

  • Only secure the loudspeaker using the specified pop rivets ⇒ Electronic parts catalogue (ETKA) .

Removing and installing rear bass loudspeakers

Special tools and workshop equipment required

  • Drill, commercially available
  • pop rivet pliers, commercially available
  • suitable drill bit approx. 4 mm, commercially available

Removing

4-door models

  • Remove rear door trim ⇒ General body repairs, interior; Rep. gr. 70 ; Rear door trims; Removing and installing rear door trim .

All vehicles (continued)

2-door models

  • Remove side trim ⇒ General body repairs, interior; Rep.

    gr. 70 ; Trims, interior; Removing and installing side trim

All vehicles (continued)

  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing and installing rear bass loudspeakers

CAUTION

Risk of eye injuries due to metal swarf.

Eye irritation and injury possible.

  • Put on safety goggles.

NOTICE

Corrosion damage due to swarf and damaged paintwork

  • Completely remove swarf from the door, and immediately rectify any paintwork damage caused.
  • Drill out pop rivets -3-, and remove loudspeaker -1-.

Installing

Install in the reverse order of removal, observing the following:

Important

  • Only secure the loudspeaker using the specified pop rivets ⇒ Electronic parts catalogue (ETKA) .

Removing and installing subwoofer [R211]

The subwoofer - R211- will henceforth be referred to as "subwoofer".

Removing

  • Remove luggage compartment floor.
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-.
  • Lift out subwoofer -1-.
Volkswagen ID.4. Removing and installing subwoofer [R211]

Removing and installing digital sound package control unit [J525]

Removing

The digital sound package control unit - J525- will henceforth be referred to as "digital sound package control unit".

If the digital sound package control unit is renewed, perform the test plan for the renewal of the control unit:

  • Carry out function "Renew digital sound package control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Remove left luggage compartment side trim ⇒ General body repairs, interior; Rep. gr. 70 ; Luggage compartment trims; Removing and installing luggage compartment side trim .
  • Disconnect electrical connector -4-.
  • Unscrew bolts -2-.
  • Unscrew nuts -3-.
  • Detach digital sound package control unit -1-.
Volkswagen ID.4. Removing and installing digital sound package control unit [J525]

Installing

Install in the reverse order of removal, observing the following:

If the digital sound package control unit has been renewed, conclude the test plan for the renewal of the control unit:

  • Conclude function "Renew digital sound package control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

Removing and installing aerial module

Removing

The radio aerial 2 - R93- , aerial - R11- and digital radio aerial - R183- will henceforth be referred to as "aerial module".

Removal and installation are described for the left vehicle side as an example.

  • Remove upper rear lid trim ⇒ General body repairs, interior; Rep. gr. 70 ; Luggage compartment trims; Removing and installing upper rear lid trim .
  • Disconnect electrical connectors -arrows-.
Volkswagen ID.4. Removing and installing aerial module
  • Unscrew bolt -2-.
  • Pull off aerial module -1- in direction of -arrow
Volkswagen ID.4. Removing and installing aerial module

Installing

Install in reverse order of removal, observing the following:

Tightening torques

Removing and installing frequency modulation (FM) frequency filters [R178]/[R179]

The frequency modulation (FM) frequency filter in negative wire - R178- and frequency modulation (FM) frequency filter in positive wire - R179- will henceforth be referred to as "frequency filter".

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove rear lid side trim ⇒ General body repairs, interior; Rep. gr. 70 ; Luggage compartment trims; Removing and installing rear lid side trim
  • Disconnect electrical connectors -2-.
  • Using commercially available plastic wedge, carefully lever out frequency filter -1-, and remove it.
Volkswagen ID.4. Removing and installing frequency modulation (FM) frequency filters [R178]/[R179]

Installing

Install in reverse order of removal.

Removing and installing roof aerial [RX5]

The roof aerial - RX5- will henceforth be referred to as "roof aerial".

Removing

  • Remove internet access control unit - J666- ⇒ Rep. gr. 91 ; Removing and installing internet access control unit [J666] .
  • Release retaining hooks -2-.
  • Remove roof aerial -1- in direction of -arrow-.
Volkswagen ID.4. Removing and installing roof aerial [RX5]

Installing

Install in reverse order of removal.

Removing and installing LTE aerial

The LTE aerial 1 - R297- and LTE aerial 2 - R306- will henceforth be referred to as "LTE aerial".

Removing

  • Remove bumper cover ⇒ General body repairs, exterior; Rep. gr. 63 ; Rear bumper; Removing and installing bumper cover .
  • Disconnect electrical connector -2-.
  • Unscrew nut -arrow-, and detach LTE aerial -1-.
Volkswagen ID.4. Removing and installing LTE aerial

Installing

Install in the reverse order of removal, observing the following:

Tightening torques

Removing and installing internet access control unit [J666]

The internet access control unit - J666- will henceforth be referred to as "internet access control unit".

Removing

Vehicles without sun blind

  • Detach moulded headliner and place it on head restraints ⇒ General body repairs, interior; Rep. gr. 70 ; Roof trims; Removing and installing moulded headliner

All vehicles (continued)

Vehicles with sun blind

  • Remove frame with sun blind ⇒ General body repairs, exterior; Rep. gr. 60 ; Sliding sunroof; Removing and installing frame with sun blind .

All vehicles (continued)

  • Disconnect electrical connectors -3-, -4- and -6-.
  • Loosen bolt -5-.
  • Release locking device -2-, and detach internet access control unit -1-.
Volkswagen ID.4. Removing and installing internet access control unit [J666]

Installing

Install in the reverse order of removal, observing the following:

Tightening torques

Removing and installing data transmission aerial

External vehicle communication aerial 2 - R394- and data transmission aerial - R180- will be referred to hereafter as "aerial".

Removing

  • Remove bottom cover ⇒ General body repairs, interior; Rep. gr. 68 ; Interior mirror; Removing and installing interior mirror .
  • Release locking devices -3-, and remove aerial -1- in direction of -arrow-.
  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing and installing data transmission aerial

Installing

Install in reverse order of removal.

Removing and installing aerial amplifier for mobile telephone [R86]

Removing

  • Remove right luggage compartment side trim ⇒ General body repairs, interior; Rep. gr. 70 ; Luggage compartment trims; Removing and installing luggage compartment side trim .
  • Unscrew bolts -2-, and remove seat trim bracket aerial amplifier for mobile telephone - R86- -1-.
  • Disconnect electrical connectors -3-.
Volkswagen ID.4. Removing and installing aerial amplifier for mobile telephone [R86]

Installing

Install in the reverse order of removal, observing the following:

Removing and installing charging unit 1 for mobile devices [J1146]

Charging unit 1 for mobile devices - J1146- is referred to hereafter as charging unit.

Removing

  • Remove lining mat from centre console storage compartment.

NOTICE

Risk of damage to component surfaces when sharp-edged levers are used

  • Mask off component in visible area using commercially available adhesive tape before using a levering tool.
  • Release locking devices -2- and remove charging unit -1-.
  • Disconnect electrical connector.
Volkswagen ID.4. Removing and installing charging unit 1 for mobile devices [J1146]

Installing

Install in reverse order of removal.

Removing and installing multifunction buttons [E440]/[E441]

The left multifunction buttons in steering wheel - E440- with multifunction steering wheel control unit - J453- and right multifunction buttons in steering wheel - E441- will henceforth be referred to as "multifunction buttons".

Removing

If the multifunction buttons control unit is renewed, perform the test plan for the renewal of the control unit:

  • Carry out function "Renew multifunction buttons" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Remove airbag unit with airbag igniter on driver side [N95] ⇒ General body repairs, interior; Rep. gr. 69 ; Driver-side airbag; Removing and installing airbag unit with airbag igniter on driver side [N95] .

NOTICE

Risk of damage to the steering wheel.

  • Mask off the steering wheel at the relevant locations to protect it from damage.
  • Mask off steering wheel -1- with adhesive tape in areas indicated by -arrows-.
Volkswagen ID.4. Removing and installing multifunction buttons [E440]/[E441]
  • Using commercially available plastic wedge -2-, unclip trim panel -1- in lower area -arrows-.
Volkswagen ID.4. Removing and installing multifunction buttons [E440]/[E441]
  • Using commercially available plastic wedge -2-, unclip trim panel -1- successively in indicated areas (-arrows A- through -arrows C-).
  • Detach trim -1- together with multifunction buttons -3-, -4- and lower trim -5-.
Volkswagen ID.4. Removing and installing multifunction buttons [E440]/[E441]

Vehicles with control unit for steering wheel contact detection - J1158-

  • Disconnect electrical connector -1-.
Volkswagen ID.4. Removing and installing multifunction buttons [E440]/[E441]

Installing

Install in the reverse order of removal, observing the following:

  • Clip in trim panel from below.

If the multifunction buttons control unit has been renewed, conclude the test plan for the renewal of the control unit:

  • Conclude function "Renew multifunction unit control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 91 ; Assembly overview - multifunction steering wheel

Removing and installing control unit for steering wheel contact detection [J1158]

The control unit for steering wheel contact detection - J1158- will henceforth be referred to as "control unit".

Removing

  • Remove airbag unit with airbag igniter on driver side [N95] ⇒ General body repairs, interior; Rep. gr. 69 ; Driver side airbag; Removing and installing airbag unit with airbag igniter on driver side [N95] .
  • Remove lower trim panel ⇒ Rep. gr. 91 ; Removing and installing multifunction buttons [E440]/[E441] .
  • Disconnect electrical connectors -1- and -3-.
  • Pull out control unit -2- in direction of -arrow-.
Volkswagen ID.4. Removing and installing control unit for steering wheel contact detection [J1158]

Installing

Install in reverse order of removal.

Removing and installing USB connection 1 [U41]

Removing

  • Remove centre console ⇒ General body repairs, interior; Rep. gr. 68 ; Centre console; Removing and installing centre console .
  • Release locking devices -1- and -2-, and pull out USB connection 1 - U41- .
Volkswagen ID.4. Removing and installing USB connection 1 [U41]

Installing

Install in the reverse order of removal, observing the following:

Important

  • The USB connection 1 - U41- must be heard to engage.

Removing and installing USB charging socket 1 [U37]

Removing

  • Remove rear centre console vent ⇒ General body repairs, interior; Rep. gr. 68 ; Centre console; Removing and installing rear centre console vent .
  • Release locking devices -2-, and pull out USB charging socket 1 - U37- -1-.
Volkswagen ID.4. Removing and installing USB charging socket 1 [U37]

Installing

Install in the reverse order of removal, observing the following:

Important

  • The USB charging socket 1 - U37- must be heard to engage.

Removing and installing emergency call module control unit and communication unit [J949], rear bench seat

Removing

Emergency call module control unit and communication unit - J949- is referred to hereafter as control unit.

If the control unit is renewed, perform the test plan for renewal of the control unit:

  • Carry out function "Renew emergency call module control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Remove bench seat/individual seats ⇒ General body repairs, interior; Rep. gr. 72 ; Rear seat; Removing and installing bench seat / individual seats .
  • Detach rear sill panel moulding ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing rear sill panel moulding .
  • Lift up floor covering until control unit is accessible ⇒ General body repairs, interior; Rep. gr. 70 ; Interior trim; Removing and installing floor covering .
  • Swivel out bracket -2- in direction of -arrow-.
Volkswagen ID.4. Removing and installing emergency call module control unit and communication unit [J949], rear bench seat
  • Disconnect electrical connectors -1-.
Volkswagen ID.4. Removing and installing emergency call module control unit and communication unit [J949], rear bench seat
  • Release locking devices -2-, and remove control unit -1-.
Volkswagen ID.4. Removing and installing emergency call module control unit and communication unit [J949], rear bench seat

Installing

Install in the reverse order of removal, observing the following:

Important

  • Control unit must audibly engage in holder.

If the control unit has been renewed, conclude the test plan for the renewal of control unit:

Conclude function "Renew emergency call module control unit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Removing and installing loudspeaker for emergency call module [R335]

Emergency call loudspeaker - R335- is referred to hereafter as loudspeaker.

Removing

Vehicles without control unit for head-up display - J898-

  • Remove loudspeaker trim ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel; Removing and installing loudspeaker trim .

All vehicles (continued)

Vehicles with control unit for head-up display - J898-

  • Remove cover for dash panel/head-up display ⇒ General body repairs, interior; Rep. gr. 70 ; Removing and installing cover for dash panel/head-up display .

All vehicles (continued)

  • Unscrew bolts -2-.
  • Pull out loudspeaker -1-.
  • Disconnect electrical connector.
Volkswagen ID.4. Vehicles with control unit for head-up display - J898-

Installing

Install in reverse order of removal, observing the following:

Tightening torques

Removing and installing emergency battery, telematics [A16]

The emergency battery, telematics - A16- will henceforth be referred to as "emergency battery".

Emergency call module control unit and communication unit - J949- is referred to hereafter as control unit.

Removing

If the emergency battery is renewed, perform the test plan for the renewal of the emergency battery.

  • Carry out function "Renew emergency battery, telematics" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

  • Remove control unit ⇒ Rep. gr. 91 ; Removing and installing emergency call module control unit and communication unit [J949] .
  • Unscrew bolt -2-.
  • Remove cover -1-.
Volkswagen ID.4. Removing and installing emergency battery, telematics [A16]
  • Disconnect connector -2-.
  • Remove emergency battery -1-.
Volkswagen ID.4. Removing and installing emergency battery, telematics [A16]

Installing

Install in the reverse order of removal, observing the following:

If the emergency battery was renewed, conclude the test plan for renewal of the emergency battery.

  • Conclude function "Renew emergency battery, telematics" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques