Underbody cladding

In this manual: Underbody cladding
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~11min read
0102030405021N·mlb·ft
Tightening torque found on this page
  • Assembly overview - underbody cladding, 55, 62 kWh
  • Assembly overview - underbody cladding, 82 kWh
  • Assembly overview - underbody cladding, 82 kWh, GTX
  • Removing and installing high-voltage battery skid plate, 55, 62 kWh
  • Removing and installing high-voltage battery skid plate, 82 kWh
  • Removing and installing side underbody cladding, 82 kWh
  • Removing and installing rear underbody cladding
  • Removing and installing underbody towing eye
  • Removing and installing power unit skid plate

Assembly overview - underbody cladding, 55, 62 kWh

Assembly overview - underbody cladding

Volkswagen ID.4. Assembly overview - underbody cladding
  1. Front underbody cladding
  • ⇒ Rep. gr. 66 ; Removing and installing front underbody cladding
  1. Bolt
  • Qty. 9
  • 2 N·m
  1. Clip
  • Qty. 4
  1. Skid plate, high-voltage battery
  • ⇒ Rep. gr. 66 ; Removing and installing skid plate for high-voltage battery
  1. Bolt
  • Repair stages ⇒ Electronic parts catalogue (ETKA)
  • Qty. 35
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing high-voltage battery skid plate, 55, 62 kWh
  1. Nut
  • Qty. 22
  • 8 N·m +30º
  1. Expanding nut
  • Qty. 5
  • Renew after removing
  1. Bolt
  • Qty. 5
  • 2 N·m
  1. Side underbody cladding/side skid plate
  • Depending on equipment/version
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Cover
  • Left and right
  • ⇒ Rep. gr. 66 ; Removing and installing underbody cladding, centre
  1. Underbody protection
  • Shape varies depending on model
  • ⇒ Rep. gr. 66 ; Removing and installing skid plate
  1. Bolt
  • Quantity varies depending on model
  • Qty. 3 or 4
  • M8 or M10
  • M8 = 20 N·m
  • M10 = 55 N·m
  1. Rear underbody cladding
  • Shape varies depending on model
  • ⇒ Rep. gr. 66 ; Removing and installing rear underbody cladding
  1. Bolt
  • Quantity varies depending on model
  • Qty. 5 or 9
  • 2 N·m
  1. Centre underbody cladding
  • ⇒ Rep. gr. 66 ; Removing and installing underbody cladding, centre
  1. Nut
  • Qty. 9
  • 2 N·m
  1. Expanding nut
  • Qty. 2
  1. Rear centre underbody cladding
  • ⇒ Rep. gr. 66 ; Removing and installing underbody cladding, rear centre
  1. Clip
  • Qty. 3
  1. Bolt
  • Qty. 2
  • 8 N·m
  1. Bolt
  • Qty. 5
  • 2 N·m
  1. Side underbody cladding/side skid plate
  • Depending on equipment/version
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Bolt
  • Qty. 5
  • 2 N·m
  1. Expanding nut
  • Qty. 5
  • Renew after removing
  1. Bolt
  • Qty. 4
  • ⇒ Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220; Rep. gr. 93 ; High-voltage battery unit; Assembly overview - installed high-voltage battery, 82 kWh; Assembly overview - installed high-voltage battery

Assembly overview - underbody cladding, 82 kWh

Assembly overview - underbody cladding

Volkswagen ID.4. Assembly overview - underbody cladding
  1. Front underbody cladding
  • ⇒ Rep. gr. 66 ; Removing and installing front underbody cladding
  1. Bolt
  • Qty. 9
  • 2 N·m
  1. Clip
  • Qty. 4
  1. Skid plate, high-voltage battery
  • ⇒ Rep. gr. 66 ; Removing and installing high-voltage battery skid plate, 82 kWh
  1. Nut
  • Qty. 34
  • Renew after removing
  • 8 N·m +30º
  1. Bolt
  • Repair stages ⇒ Electronic parts catalogue (ETKA)
  • Qty. 39
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing high-voltage battery skid plate, 82 kWh
  1. Expanding nut
  • Qty. 5
  • Renew after removing
  1. Bolt
  • Qty. 5
  • 2 N·m
  1. Side underbody cladding/side skid plate
  • Depending on equipment/version
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Cover
  • Left and right
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Rear side member trim/skid plate support
  • Depending on equipment/version
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Bolt
  • Qty. 2
  • 2 N·m
  1. Underbody protection
  • Shape varies depending on model
  • ⇒ Rep. gr. 66 ; Removing and installing skid plate
  1. Bolt
  • Quantity varies depending on model
  • Qty. 3 or 4
  • M8 or M10
  • M8 = 20 N·m
  • M10 = 55 N·m
  1. Rear underbody cladding
  • Shape varies depending on model
  • ⇒ Rep. gr. 66 ; Removing and installing rear underbody cladding
  1. Bolt
  • Qty. 5
  • 2 N·m
  1. Rear centre underbody cladding
  • ⇒ Rep. gr. 66 ; Removing and installing underbody cladding, rear centre
  1. Clip
  • Qty. 5
  1. Clip
  • Qty. 3
  1. Bolt
  • Qty. 2
  • 8 N·m
  1. Bolt
  • Qty. 2
  • 2 N·m
  1. Bolt
  • Qty. 4
  • ⇒ Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220; Rep. gr. 93 ; High-voltage battery unit; Assembly overview - installed high-voltage battery, 82 kWh; Assembly overview - installed high-voltage battery
  1. Side underbody cladding/side skid plate
  • Depending on equipment/version
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Bolt
  • Qty. 5
  • 2 N·m 25 - Expanding nut
  • Qty. 5
  • Renew after removing

Assembly overview - underbody cladding, 82 kWh, GTX

Assembly overview - underbody cladding

Volkswagen ID.4. Assembly overview - underbody cladding
  1. Front underbody cladding
  • ⇒ Rep. gr. 66 ; Removing and installing front underbody cladding
  1. Skid plate, high-voltage battery
  • ⇒ Rep. gr. 66 ; Removing and installing skid plate for high-voltage battery
  1. Side underbody cladding/ side skid plate
  • Depending on equipment/ version
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Rear side member trim/ skid plate support
  • Depending on equipment/ version
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Cover
  • Left and right
  • ⇒ Rep. gr. 66 ; Removing and installing side underbody cladding
  1. Underbody protection
  • ⇒ Rep. gr. 66 ; Removing and installing skid plate
  1. Bolt
  • Qty. 3
  • M8 or M10
  • M8 = 20 N·m
  • M10 = 55 N·m
  1. Rear underbody cladding
  • ⇒ Rep. gr. 66 ; Removing and installing rear underbody cladding
  1. Bolt
  • Qty. 9
  • 2 N·m
  1. Rear power unit skid plate
  • ⇒ Rep. gr. 66 ; Removing and installing power unit skid plate
  1. Bolt
  • Qty. 2
  • 8 N·m
  1. Clip
  • Qty. 3
  • Bolt
  • Qty. 2
  • 20 N·m
  1. Speed nut
  • Qty. 4
  1. Bolt
  • Depending on equipment/version
  • Qty. 4
  • 2 N·m
  1. Power unit skid plate
  • Depending on equipment/version
  • ⇒ Rep. gr. 66 ; Removing and installing power unit skid plate
  1. Nut
  • Qty. 34
  • Renew after removing
  • 8 N·m +30º
  1. Bolt
  • Repair stages ⇒ Electronic parts catalogue (ETKA)
  • Qty. 39
  • Renew after removing
  • ⇒ Rep. gr. 66 ; Removing and installing high-voltage battery skid plate, 82 kWh
  1. Bolt
  • Qty. 4
  • 2 N·m
  1. Bolt
  • Qty. 10
  • 2 N·m
  1. Expanding nut
  • Qty. 10
  • Renew after removing
  1. Clip
  • Qty. 4
  1. Bolt
  • Qty. 9
  • 2 N·m

Removing and installing high-voltage battery skid plate, 55, 62 kWh

Removing and installing skid plate for high-voltage battery

Special tools and workshop equipment required

  • 16 mm hexagon socket bit - VAS 262 017-

Removing

NOTICE

Damage to the thread is possible when unscrewing the bolts.

  • Unscrew the bolts with slowly increasing speed
  • Unscrew bolts -1-.
  • Unscrew bolts -4- using 16 mm hexagon socket bit - VAS 262 017- .
  • Unscrew nuts -3-.

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Pull skid plate for high-voltage battery -2- out in direction of -arrow- and detach.
Volkswagen ID.4. Removing and installing high-voltage battery skid plate, 55, 62 kWh

Installing

Install in reverse order of removal, observing the following:

Tightening torques

Specified torque for flow-drill screws

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding, 55, 62 kWh
  • ⇒ Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220; Rep. gr. 93 ; High-voltage battery unit; Assembly overview - installed high-voltage battery, 82 kWh; Assembly overview - installed high-voltage battery

Removing and installing high-voltage battery skid plate, 82 kWh

Removing and installing skid plate for high-voltage battery

Special tools and workshop equipment required

  • 16 mm hexagon socket bit - VAS 262 017-

Removing

NOTICE

Damage to the thread is possible when unscrewing the bolts.

  • Unscrew the bolts with slowly increasing speed
  • Unscrew bolts -4- using 16 mm hexagon socket bit - VAS 262 017- .
  • Unscrew bolts -1-.
  • Unscrew nuts -3-.

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Pull skid plate for high-voltage battery -2- out in direction of -arrow- and detach.
Volkswagen ID.4. Removing and installing high-voltage battery skid plate, 82 kWh

Installing

Install in reverse order of removal, observing the following:

Tightening torques

Specified torque for flow-drill screws

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding, 82 kWh
  • ⇒ Electric rear-wheel drive EIP220 and all-wheel drive EIA200, EIP220; Rep. gr. 93 ; High-voltage battery unit; Assembly overview - installed high-voltage battery, 82 kWh; Assembly overview - installed high-voltage battery

Removing and installing front underbody cladding

Removing

  • Unscrew bolts -2- and -3-.
  • Unclip clips -4-.
  • Pull front underbody cladding -1- in direction of -arrow A- out of bumper cover, and remove it.
Volkswagen ID.4. Removing and installing front underbody cladding

Installing

  • Install in reverse order of removal, observing the following:

Important

  • Middle bolt must be started first.

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding
  • ⇒ Rep. gr. 66 ; Assembly overview - front wheel housing liner
  • ⇒ Rep. gr. 63 ; Assembly overview - bumper cover

Removing and installing side underbody cladding, 55 kWh, 62 kWh

Removing and installing side underbody cladding

Removal and installation are described for the right vehicle side as an example.

Removing

Removing side underbody cladding

  • Unclip cover -1-.
  • Unscrew bolts -2-.
  • Remove expanding nuts -2-.
  • Remove side underbody cladding -3-.
Volkswagen ID.4. Removing and installing side underbody cladding

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding

Removing and installing side underbody cladding, 82 kWh

Removing and installing side underbody cladding

Removal and installation are described for the right vehicle side as an example.

Removing

Remove side underbody cladding

  • Unclip cover -1-.
  • Unscrew bolts -3-.
  • Remove expanding nuts -3-.
  • Remove side underbody cladding -5-.
Volkswagen ID.4. Removing and installing side underbody cladding, 82 kWh

Remove rear side member trim/skid plate support

  • Unscrew bolts -2-.
  • Detach rear side member trim -4-.
Volkswagen ID.4. Removing and installing side underbody cladding, 82 kWh

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding, 82 kWh

Removing and installing centre underbody cladding

Removing

  • Unclip covers -3-.
  • Unscrew nuts -4-.
  • Unscrew bolts -5- and -6-.
  • Unclip expanding nuts -2-.
  • Pull out centre underbody cladding -1- in direction of -arrow A-.
Volkswagen ID.4. Removing and installing centre underbody cladding

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding

Removing and installing rear underbody cladding

Removing

  • Remove rear centre underbody cladding ⇒ Rep. gr. 66 ; Removing and installing rear centre underbody cladding .
  • Unscrew bolts -2-.
  • Pull rear underbody cladding -1- in direction of -arrow A- out of bumper cover, and remove it.
Volkswagen ID.4. Removing and installing rear underbody cladding

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding
  • ⇒ Rep. gr. 66 ; Assembly overview - rear wheel housing liner

Removing and installing skid plate

Removing

  • Remove rear underbody cladding ⇒ Rep. gr. 66 ; Removing and installing rear underbody cladding .
  • Unscrew bolts -2-.
  • Remove skid plate -1-.
Volkswagen ID.4. Removing and installing skid plate

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding

Removing and installing underbody towing eye

Removing

  • Remove rear underbody cladding ⇒ Rep. gr. 66 ; Removing and installing rear underbody cladding .

Underbody towing eye with four M8 bolts

  • Remove bolts -2-.
  • Detach underbody towing eye -1- in direction of -arrow-.
  • Remove underbody towing eye -1-.
Volkswagen ID.4. Removing and installing underbody towing eye

All vehicles (continued)

Underbody towing eye with two M10 bolts

  • Remove bolts -2-.
  • Detach underbody towing eye -1- in direction of -arrow-.
  • Remove underbody towing eye -1-.
Volkswagen ID.4. Removing and installing underbody towing eye

All vehicles (continued)

Installing

Further installation is carried out in reverse order of removal.

Observe the following when doing this:

Tightening torques

Removing and installing power unit skid plate

Skid plate for power unit protection is referred to hereafter as skid plate.

Removing

  • Unscrew bolts -2-.
Volkswagen ID.4. Removing and installing power unit skid plate
  • Turn skid plate in direction of -arrow A- and remove from guides in direction of -arrow B-.
Volkswagen ID.4. Removing and installing power unit skid plate

Installing

Further installation is carried out in reverse order of removal.

Observe the following when doing this:

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding, 82 kWh, GTX

Removing and installing power unit skid plate

Removing and installing underbody cladding, rear centre

Removing and installing power unit skid plate

Removing

  • Unscrew bolts -3- and -4-.
  • Unclip clips -2-.
  • Remove rear power unit skid plate -1-.
Volkswagen ID.4. Removing and installing power unit skid plate

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding, 82 kWh, GTX

Removing and installing underbody cladding, rear centre

Removing and installing rear centre underbody cladding

Removing

  • Unscrew bolts -3- and -4-.
  • Unclip clips -2-.
  • Remove rear centre underbody cladding -1-.
Volkswagen ID.4. Removing and installing rear centre underbody cladding

Installing

Install in reverse order of removal, observing the following

Tightening torques

  • ⇒ Rep. gr. 66 ; Assembly overview - underbody cladding