Electric drive motor

In this manual: Electric drive motor
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
13steps
~78min
3/5difficulty
010203040501612N·mlb·ft
Tightening torque found on this page
Done 0 of 13

Calibrating three-phase current drive VX54

Calibration of the three-phase current drive - VX54- becomes necessary if:

  • the event memory of systems relevant to OBD has been cleared;
  • the software for the electric drive control unit - J841- was updated;
  • the electric drive control unit - J841- has been renewed;
  • the power and control electronics for electric drive - JX1- has been renewed;
  • the three-phase current drive - VX54- has been renewed.

Calibration is preformed automatically the first time the vehicle is driven. The power output of the drive motor is restricted until the motor has been successfully calibrated.

If the calibration is to be carried out manually:

  • Carry out function "Calibrate electric drive motor" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • Leakage test of electric drive motor, rear
  • Assembly overview - electric drive motor, rear
  • Assembly overview - electric drive motor, front
  • Removing and installing drive motor rotor position sender 1 [G713]
  • Removing and installing drive motor rotor position sender, front

Leakage test of electric drive motor, rear

Special tools and workshop equipment required

  • Leakage test kit - VAS 691 005/15-
  • distributing mechanism - VAS 691 005/1-
  • plug - T10607/4-
  • plug - T10633-
  • pressure and vacuum pump - VAS 671 005-
  • pressure sensor - V.A.G 1397B-
  • seal - T10634-
  • stopper - VAS 691 005/11-2-
  • test adapter - VAS 691 005/4-

The power and control electronics for electric drive - JX1- will henceforth be referred to as "power electronics".

Important

  • Three-phase current drive - VX54- with power and control electronics for electric drive - JX1- must be secured to motor and gearbox support.
  • Sealant must be allowed to dry for at least 15 minutes before carrying out the leakage test.

Carry out the steps below one after the other.

Step 1: Leak testing of tools

  • Connect pressure and vacuum pump - VAS 671 005- -D- on pressure side to distributing mechanism - VAS 691 005/1- -B-.
  • Connect pressure sensor - V.A.G 1397B- -C- to distributing mechanism -B-.
  • Open all shut-off taps -arrows- on distributing mechanism -B-.
  • Connect distributing mechanism -B- to adapter - VAS 691 005/15-3- -E-.
  • Switch on pressure sensor -C-. Select "mbar" and relative pressure measurement "rEL".
  • Close shut-off tap -arrow- on adapter -E-.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Generate a pressure of 1000 mbar using pressure and vacuum pump -D-.
  • When pressure is reached, close shut-off tap -arrow- on distributing mechanism -B-.
  • Observe pressure sensor -C- for approx. 1 minute.

Important

  • The pressure must not drop.

Note

Due to the pressure sensor's high accuracy, the displayed pressure may fluctuate.

Volkswagen ID.4. Leakage test of electric drive motor, rear

Step 2: Leak testing of motor and gearbox

  • Seal electrical connections of power electronics -1- with plug - T10607/4- -J- and plug - T10633- -K-.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Fit seal - T10634- -L- onto power and control electronics -1- as shown in illustration.
  • Position sealing disc centrally in front of bleeder valve -arrow-.
  • Screw in spindle -2- by hand.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Insert stopper - VAS 691 005/15-1- -F- in left input shaft flange.
  • Screw in clamping nut -1- by hand.
  • Hook safety cable -2- onto motor.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Insert stopper - VAS 691 005/15-1- -G- in right input shaft flange.
  • Screw in clamping nut -1- by hand.
  • Hook safety cable -2- onto motor.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Press in locking element -arrow- and fit adapter - VAS 691 005/15-3- -E- onto gearbox breather.
  • Release locking element -arrow- and pull to check it has locked.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Using a small screwdriver, carefully lever out bleeder valve -1- -arrow-.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Mount test adapter - VAS 691 005/15-2- -A- on motor.

Important

  • Compressed air connection -1- must align with hole for bleeder valve -arrow-.
  • Screw in knurled screws -2- by hand.
  • Turn compressed air connection -1- centrally against hole for bleeder valve until it is finger-tight.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Connect distributing mechanism -B- with pressure sensor -C- and pressure and vacuum pump -D- to adapter -E-.
  • Open all shut-off taps -arrows-.
  • Switch on pressure sensor -C-. Select "mbar" and relative pressure measurement "rEL".
  • Generate a pressure of 200 mbar using pressure and vacuum pump -D-.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • When pressure is reached, close shut-off tap -arrow- on distributing mechanism -B-.
  • Observe pressure sensor for 5 minutes.
Volkswagen ID.4. Leakage test of electric drive motor, rear

Important

  • The pressure must not drop by more than 2 mbar.
  • If the pressure drops by more than 2 mbar locate the leak using a commercially available leak detection spray.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • If gearbox side is leak-tight, close shut-off tap -arrow- on adapter -E-.

Note

Pressure in gearbox must not be released. It is needed to leaktest the motor side.

Checking motor side for leaks

  • Connect distributing mechanism -B- with pressure sensor -C- and pressure and vacuum pump -D- to test adapter - VAS 691 005/15-2- -A-.
  • Open all shut-off taps -arrows- on distributing mechanism -B-.
  • Switch on pressure sensor -C-. Select "mbar" and relative pressure measurement "rEL".
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Generate a pressure of 200 mbar using pressure and vacuum pump -D-.
  • When pressure is reached, close shut-off tap -arrow- on distributing mechanism -B-.
  • Observe pressure sensor -C- for 5 minutes.

Important

  • The pressure must not drop by more than 2 mbar.
  • If the pressure drops by more than 2 mbar locate the leak using a commercially available leak detection spray.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Following leakage test, remove pressure and vacuum pump -D-.
  • First release pressure on motor side by opening shut-off tap -arrow 1-. Then open shut-off tap -arrow 2-.
  • Remove all tools.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Apply thin coat of special lubricant to sealing seat for bleeder valve on bearing plate -arrow-, and install new bleeder valve -1-.

Special lubricant ⇒ Electronic parts catalogue (ETKA)

Volkswagen ID.4. Leakage test of electric drive motor, rear

Step 3: Leak testing motor on coolant side

  • Seal coolant connection -1- at bottom on power electronics using stopper - VAS 691 005/11-2- -H-.
  • Secure stopper with hose clip -arrow-.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Connect test adapter - VAS 691 005/4- -I- to coolant connection -2-.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Connect distributing mechanism -B- with pressure sensor -C- and pressure and vacuum pump -D- to test adapter -I-.
  • Open all shut-off taps -arrows- on distributing mechanism -B-.
Volkswagen ID.4. Leakage test of electric drive motor, rear
  • Generate a pressure of 1000 mbar using pressure and vacuum pump -D-.
  • When this pressure has been reached, close shut-off tap -arrow-.
  • Observe pressure sensor -C- for 5 minutes.

Important

  • The pressure must not drop by more than 1 mbar.
  • If the pressure drops by more than 1 mbar locate the leak using a commercially available leak detection spray.
Volkswagen ID.4. Leakage test of electric drive motor, rear

Important

  • If leaks have been located and sealed, repeat leakage test.
  • If no leakage was detected, remove all tools.

Assembly overview - electric drive motor, rear

Volkswagen ID.4. Assembly overview - electric drive motor, rear
  1. Power and control electronics for electric drive - JX1-
  • With electric drive control unit - J841-
  • With intermediate circuit capacitor 1 - C25-
  • With DC/AC converter for drive motor - A37-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive at rear
  1. Bolt
  • Qty. 4
  • Renew after removing
  • 16 N·m +135º
  1. Connecting piece
  • Renew after removing
  1. Dowel sleeve
  • Qty. 2
  1. Three-phase current drive - VX54- with gearbox
  • With electric drive motor - V141-
  • ⇒ Rep. gr. 10 ; Removing rear motor
  1. Drive motor rotor position sender 1 - G713-
  • With drive motor temperature sender - G712-
  • ⇒ Rep. gr. 93 ; Removing and installing drive motor rotor position sender 1 [G713]
  1. Bolt
  • Qty. 6
  • Renew after removing
  • 4 N·m +90º
  1. Cover
  • Renew after removing
  1. Bolt
  • Qty. 7
  • Renew after removing
  • Specified torque and tightening sequence
  1. Centre hex stud
  • Qty. 2
  • Renew after removing
  • Specified torque and tightening sequence
  1. Clamping washer
  • Qty. 2
  1. Noise insulation
  2. Bolt
  • Qty. 3
  • Renew after removing
  • 8 N·m +90º

Cover - specified torque and tightening sequence

Volkswagen ID.4. Assembly overview - electric drive motor, rear

Assembly overview - electric drive motor, front

Volkswagen ID.4. Assembly overview - electric drive motor, front
  1. Bleeder valve
  2. Power and control electronics 2 for electric drive - JX4-
  • With electric drive control unit 2 - J944-
  • With intermediate circuit capacitor 2 - C26-
  • With DC/AC converter for drive motor 2 - A55-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive, front
  1. Bolt
  • Qty. 2
  • Renew after removing
  • 30 N·m +45º
  1. Connecting piece
  • Renew after removing
  1. Gasket/sealant
  • Gasket or sealant, depending on equipment
  • Renew after removing
  1. Dowel pins
  • Qty. 2
  • Renew after removing
  1. Three-phase current drive 2 - VX97- with gearbox
  • With electric drive motor 2 - V717-
  1. Seal
  2. O-ring
  • Renew after removing
  1. Coolant connection
  2. Bolt
  • Qty. 2
  • Renew after removing
  • 5 N·m
  1. Rotor position sender 1 for drive motor 2 - G1147-
  • With drive motor 2 temperature sender - G1146-
  • ⇒ Rep. gr. 93 ; Removing and installing drive motor rotor position sender, front
  1. Bolt
  • Qty. 2
  • 3,5 N·m
  1. Oil drain plug
  • Renew after removing
  • 15 N·m
  1. Seal
  • Renew after removing
  1. Bearing plate with shaft
  2. Seal
  3. Bolt
  • Qty. 7
  • Renew after removing
  • Specified torque and tightening sequence
  1. Seal
  2. Plug
  • Renew after removing
  • 15 N·m
  1. Gasket
  • Renew after removing
  1. Bolt
  • Qty. 2
  • Renew after removing
  • 30 N·m +45º
  1. Bolt
  • Tighten diagonally and alternately
  • Qty. 4
  • Renew after removing
  • 6 N·m
  1. Cover
  • Renew after removing
  1. Bolt for bus bar
  • Qty. 3
  • Renew after removing
  • 9 N·m
  1. O-ring
  • Renew after removing
  1. Bolt
  • Qty. 2
  • Renew after removing
  • 5 N·m
  1. Coolant connection

Bearing plate - specified torque and tightening sequence

Volkswagen ID.4. Assembly overview - electric drive motor, front

Removing and installing drive motor rotor position sender 1 [G713]

Drive motor rotor position sender 1 - G713- will be referred to hereafter as "sender".

Note

Bolts could fall into the motor. Turn the motor to horizontal position.

Removing

  • Remove power and control electronics for electric drive - JX1- ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive .
  • Unscrew bolts -arrows- for sender -A-.
Volkswagen ID.4. Removing and installing drive motor rotor position sender 1 [G713]
  • Pull sender -A- off connection -2- -arrow-.
Volkswagen ID.4. Removing and installing drive motor rotor position sender 1 [G713]

Installing

  • Fit sender -A- onto connection -2- -arrow-.
Volkswagen ID.4. Removing and installing drive motor rotor position sender 1 [G713]
  • Make sure that sender -A- is properly seated on dowel pin -arrow-.
  • Insert bolts -1- and -2-.
  • First tighten bolts -1- and then bolts -2-.
Volkswagen ID.4. Removing and installing drive motor rotor position sender 1 [G713]
  • Install power and control electronics for electric drive - JX1- ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive, rear .

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - power and control electronics for electric drive, rear

Removing and installing drive motor rotor position sender, front

Rotor position sender 1 of drive motor 2 - G1147- will be referred to hereafter as "sender".

Removing

  • ⇒ Rep. gr. 10 ; Remove front motor .
  • ⇒ Rep. gr. 10 ; Secure motor to engine and gearbox support .
  • Unscrew bolts -arrows- for bearing plate -1-.
  • Pull bearing plate together with shaft out of motor.
Volkswagen ID.4. Removing and installing drive motor rotor position sender, front
  • Pull electrical connectors -2- off sender -1-.
Volkswagen ID.4. Removing and installing drive motor rotor position sender, front
  • Unscrew bolts -arrows-, and detach sender -1-.
Volkswagen ID.4. Removing and installing drive motor rotor position sender, front

Installing

  • Insert sender -1-, and tighten bolts -arrows-.
Volkswagen ID.4. Removing and installing drive motor rotor position sender, front
  • Make sure that gasket -arrow- has been properly inserted at electrical connector.
Volkswagen ID.4. Removing and installing drive motor rotor position sender, front
  • Connect electrical connectors -2-. Check for proper engagement by pulling.
Volkswagen ID.4. Removing and installing drive motor rotor position sender, front
  • Thoroughly clean sealing surfaces on bearing plate and motor.
  • Insert bearing plate with shaft and new seal into motor.
  • Tighten bolts -arrows- for bearing plate.
Volkswagen ID.4. Removing and installing drive motor rotor position sender, front

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - electric drive motor, front