Steering column

In this manual: Steering column
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
14steps
~84min
3/5difficulty
010203040502015N·mlb·ft
Tightening torque found on this page
Done 0 of 14
  • Assembly overview - steering column
  • Removing and installing steering column
  • Removing and installing intermediate steering shaft
  • Removing and installing control unit for electronic steering column lock J764

Assembly overview - steering column

Assembly overview - steering column, left-hand drive vehicles

Volkswagen ID.4. Assembly overview - steering column, left-hand drive vehicles
  1. Central tube for dash panel
  • ⇒ General body repairs, interior; Rep.

    gr. 70 ; Central tube for dash panel; Assembly overview - central tube for dash panel

  • ⇒ General body repairs, interior; Rep.

    gr. 70 ; Central tube for dash panel; Removing and installing central tube for dash panel

  1. Shear bolt
  • Qty. 2
  1. Bracket for dash panel insert
  2. Steering column
  • ⇒ Rep. gr. 48 ; Removing and installing steering column
  1. Control unit for electronic steering column lock - J764-
  • ⇒ Rep. gr. 48 ; Removing and installing control unit for electronic steering column lock - J764-
  1. Bolt
  • Qty. 2
  • M 8 x 28
  • 20 N·m
  1. Bolt
  • Qty. 2
  • M 8 x 32
  • 20 N·m
  1. Crash bar
  • ⇒ General body repairs, interior; Rep. gr. 70 ; Central tube for dash panel; Removing and installing crash bar
  1. Intermediate steering shaft
  • ⇒ Rep. gr. 48 ; Removing and installing intermediate steering shaft
  1. Bolt
  • Renew after removing
  • M8 x 35
  • 20 N·m +90º
  1. Universal joint
  2. Bolt
  • Renew after removing
  • M8 x 35
  • 20 N·m +90º
  1. Gasket
  2. Bolt
  • Renew after removing
  • M8 x 35
  • 20 N·m +90º

Assembly overview - steering column, right-hand drive

Volkswagen ID.4. Assembly overview - steering column, right-hand drive
  1. Central tube for dash panel
  • ⇒ General body repairs, interior; Rep.

    gr. 70 ; Central tube for dash panel; Assembly overview - central tube for dash panel

  • ⇒ General body repairs, interior; Rep.

    gr. 70 ; Central tube for dash panel; Removing and installing central tube for dash panel

  1. Shear bolt
  • Qty. 2
  1. Bracket for dash panel insert
  2. Control unit for electronic steering column lock - J764-
  • ⇒ Rep. gr. 48 ; Removing and installing control unit for electronic steering column lock - J764-
  1. Line retainer
  2. Bolt
  • Qty. 2
  • M 8 x 28
  • 20 N·m
  1. Crash bar
  • ⇒ General body repairs, interior; Rep.

    gr. 70 ; Central tube for dash panel; Removing and installing crash bar

  1. Bolt
  • Renew after removing
  • M8 x 35
  • 20 N·m +90º
  1. Intermediate steering shaft
  • ⇒ Rep. gr. 48 ; Removing and installing intermediate steering shaft
  1. Bolt
  • Renew after removing
  • M8 x 35
  • 20 N·m +90º
  1. Universal joint
  2. Bolt
  • Renew after removing
  • M8 x 35
  • 20 N·m +90º
  1. Gasket
  2. Bolt
  • Qty. 2
  • M 8 x 28
  • 20 N·m
  1. Steering column
  • ⇒ Rep. gr. 48 ; Removing and installing steering column

Checking steering column for damage

  • Check steering column and components of steering column for damage.
  • Check if steering column moves smoothly and easily.
  • Check steering column for ease of movement in horizontal and longitudinal directions.

Removing and installing steering column

Removing

The control unit for electronic steering column lock - J764- will henceforth be referred to as "control unit for electronic steering column lock".

NOTICE

Risk of damage to the control unit for electronic steering column lock from failing to adhere to the specified procedure.

Before removing the steering column, make sure that the following conditions are met:

  • Discharge any static electricity by briefly touching door striker pin.
  • Turn wheels to straight-ahead position.
  • Disconnect battery ⇒ Electrical system; Rep. gr. 27 ; Battery; Disconnecting and connecting battery .
  • Pull down lever on side of steering column.
  • Swing steering column down as far as possible and pull out.
  • Press lever on side of steering column back up.
  • Remove steering column electronics control unit - J527- ⇒ Electrical system; Rep. gr. 94 ; Steering column switch module; Removing and installing steering column electronics control unit [J527] .
  • Remove footwell vent on driver side ⇒ Heating, air conditioning; Rep. gr. 87 ; Air duct; Removing and installing footwell vent on driver side .
  • Remove dash panel cover on driver side ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel; Assembly overview - dash panel .
  • Release and pull off cable duct -1- for electrical wire -2- on steering column -3-.
Volkswagen ID.4. Removing and installing steering column
  • Unclip cable retainer -3- for electrical wire -2-.
  • Disconnect electrical connector -4- on control unit for electronic steering column lock - J764- -5-.
Volkswagen ID.4. Removing and installing steering column
  • Pull cable duct -2- in direction of -arrow- off retainer -3- on steering column -1-.
Volkswagen ID.4. Removing and installing steering column
  • Remove cable holder -1-.
Volkswagen ID.4. Removing and installing steering column
  • To do this, release cable holder -1- -arrows-, and remove it.
Volkswagen ID.4. Removing and installing steering column
  • Release cable holder -1- -arrows-, and remove it.
Volkswagen ID.4. Removing and installing steering column
  • Unscrew bolt -1- from universal joint -2-.
  • Pull intermediate steering shaft -3- in direction of -arrow- off universal joint -2-
Volkswagen ID.4. Removing and installing steering column
  • Unscrew bolts -2- and -3-.
  • Detach crash bar -1- from steering column -4-.
Volkswagen ID.4. Removing and installing steering column
  • Unscrew bolts -2- and -3-.
Volkswagen ID.4. Removing and installing steering column
  • Pull steering column -1- in direction of front seat out of guides on dash panel cross member -2-.
Volkswagen ID.4. Removing and installing steering column

Installing

Install in reverse order of removal, observing the following:

  • Carry out function Renewing/Removing and installing steering column electronics control unit - J527- , as required, using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • Perform basic setting for steering angle sender - G85- using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Tightening torques

  • ⇒ Rep. gr. 48 ; Assembly overview - steering column

Removing and installing intermediate steering shaft

Removing

  • Remove front underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing front underbody cladding .
  • Remove footwell vent on driver side ⇒ Heating, air conditioning system; Rep. gr. 87 ; Air duct; Removing and installing footwell vent on driver side .
  • Pull down lever on side of steering column.
  • Pull out steering wheel as far as possible, and move it to lowest position.
  • Press lever on side of steering column back up.
  • Disconnect battery ⇒ Electrical system; Rep. gr. 27 ; Battery; Disconnecting and connecting battery .
  • Unscrew bolt -1- from universal joint -2-.
  • Turn steering wheel to straight ahead position.
  • Pull intermediate steering shaft -3- in direction of -arrow- off universal joint.
Volkswagen ID.4. Removing and installing intermediate steering shaft

Vehicles with all-wheel drive

  • Remove drive shaft on driver side ⇒ Running gear, axles, steering; Rep. gr. 40 ; Drive shaft; Removing and installing drive shaft .

All vehicles (continued)

Left-hand drive vehicles

  • Unscrew bolt -3-.
  • Pull universal joint -1- in direction of -arrow- off steering rack -4-.
Volkswagen ID.4. Removing and installing intermediate steering shaft
  • Unclip seal -1- from bulkhead -3-.
  • To do this, press catches in direction of -arrow-, and release.
  • Pull out steering column -2- working from vehicle interior.
Volkswagen ID.4. Removing and installing intermediate steering shaft

All vehicles (continued)

Right-hand drive vehicles

  • Unscrew bolt -3-.
  • Pull universal joint -1- in direction of -arrow- off steering rack -4-.
Volkswagen ID.4. Removing and installing intermediate steering shaft
  • Unclip seal -1- from bulkhead -3-.
  • To do this, press catches in direction of -arrow- and release.
  • Pull out steering column -2- working from vehicle interior.
Volkswagen ID.4. Removing and installing intermediate steering shaft

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

  • Make sure that all four catches of seal are properly seated on bulkhead.
  • Pull on strut members of seal to ensure proper engagement.
  • Carry out visual inspection, and ensure proper seating.

Tightening torques

  • ⇒ Rep. gr. 48 ; Assembly overview - steering rack
  • ⇒ Rep. gr. 48 ; Assembly overview - steering column

Removing and installing control unit for electronic steering column lock J764

Tools and auxiliary equipment required:

  • Metal saw, commercially available
  • Flat-bladed screwdriver, commercially available

The control unit for electronic steering column lock - J764- will henceforth be referred to as "control unit for electronic steering column lock".

Removing

  • If the control unit for electronic steering column lock is renewed, perform the test plan for the renewal of the control unit for electronic steering column lock ⇒ Vehicle diagnostic tester.

NOTICE

Risk of damage to the control unit for electronic steering column lock from failing to adhere to the specified procedure.

Before removing the steering column, make sure that the following conditions are met:

  • Discharge any static electricity by briefly touching door striker pin.
  • The wheels must be in straight-ahead position.
  • Disconnect battery ⇒ . Electrical system; Rep. gr. 27 ; Battery; Disconnecting and connecting battery .
  • Turn wheels to straight-ahead position.
  • Pull down lever on side of steering column.
  • Swing steering column down as far as possible and pull out.
  • Press lever on side of steering column back up.
  • Remove steering column electronics control unit - J527- ⇒ Electrical system; Rep. gr. 94 ; Steering column switch module; Removing and installing steering column electronics control unit [J527] .
  • Release and pull off cable duct -1- for electrical wire -2- on steering column -3-.
Volkswagen ID.4. Removing and installing control unit for electronic steering column lock J764
  • Unclip cable retainer -3- for electrical wire -2-.
  • Disconnect electrical connector -4- on control unit for electronic steering column lock -5-.
Volkswagen ID.4. Removing and installing control unit for electronic steering column lock J764
  • Saw open bracket -1- in area of bolts -2- using suitable workshop equipment.
  • For this, saw through bracket -1- vertically -arrows A- and horizontally -arrows B-.
  • Lever off bracket -1- using a suitable flat-bladed screwdriver.
  • Detach bracket -1- from steering column -3-.
Volkswagen ID.4. Removing and installing control unit for electronic steering column lock J764
  • Using a suitable metal saw, make a notch -arrows- in centre of bolts along entire bolt head -2-.
  • Insert suitable flat-bladed screwdriver into notch, and unscrew bolts -2-.
Volkswagen ID.4. Removing and installing control unit for electronic steering column lock J764

Important

  • It is essential to make sure that no other components become damaged when using tools.
  • It is essential to make sure that no swarf makes its way into components.
  • Thoroughly, remove any swarf.
  • Remove control unit for electronic steering column lock -1- from steering column -4-

Installing

Install in reverse order of removal, observing the following:

  • Renew bracket for control unit for electronic steering column lock -1-.
  • Fit bracket for control unit for electronic steering column lock -1-, and screw new bolts -3- for control unit for electronic steering column lock into steering column -2-.
  • Tighten bolts -3- until shear heads break off.
Volkswagen ID.4. Removing and installing control unit for electronic steering column lock J764
  • After the control unit for electronic steering column lock has been renewed, conclude the test plan for the renewal of the control unit for electronic steering column lock ⇒ Vehicle diagnostic tester.

Tightening torques

  • ⇒ Rep. gr. 48 ; Assembly overview - steering column
  • ⇒ Rep. gr. 48 ; Assembly overview - steering wheel