Cooling system/coolant

In this manual: Cooling system/coolant
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
144steps
~864min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 144
  • Connection diagram - coolant hoses, refrigerant R744
  • Connection diagram - coolant hoses, refrigerant R1234yf
  • Overview of fitting locations - cooling system, rear-wheel drive
  • Overview of fitting locations - cooling system, all-wheel drive
  • Assembly overview - cooling system, rear-wheel drive
  • Assembly overview - cooling system, all-wheel drive
  • Checking cooling system for leaks
  • Removing and installing coolant expansion tank
  • Checking filling quality
  • Draining coolant
  • Filling cooling system

Connection diagram - coolant hoses, refrigerant R744

Connection diagram - coolant hoses, rear-wheel drive

Volkswagen ID.4. Connection diagram - coolant hoses, rear-wheel drive
  1. Charging unit 1 for highvoltage battery - AX4-
  • With control unit for high-voltage battery charging unit - J1050-
  1. Three-phase current drive - VX54-
  • With power and control electronics for electric drive - JX1-
  1. High-voltage battery 1 - AX2-
  2. Coolant pump for low-temperature circuit - V468-
  3. Mixing valve for highvoltage battery pre-heating - V683-
  4. Mixing valve 2 for highvoltage battery pre-heating - V696-
  5. Coolant pump for highvoltage battery - V590-
  6. Voltage converter - A19-
  7. PTC heater element 3 - Z132-
  8. Radiator
  9. Heat exchanger for highvoltage battery
  10. Thermostat
  11. Coolant expansion tank

Connection diagram - coolant hoses, four-wheel drive

Volkswagen ID.4. Connection diagram - coolant hoses, four-wheel drive
  1. Voltage converter - A19-
  2. Charging unit 1 for highvoltage battery - AX4-
  • With control unit for high-voltage battery charging unit - J1050-
  1. Three-phase current drive - VX54-
  • With power and control electronics for electric drive - JX1-
  1. Coolant hose
  • Equipment version depending on vehicle version
  1. High-voltage battery 1 - AX2-
  2. Mixing valve 2 for highvoltage battery pre-heating - V696-
  3. Mixing valve for highvoltage battery pre-heating - V683-
  4. Coolant pump for low-temperature circuit - V468-
  5. Power and control electronics 2 for electric drive - JX4-
  6. PTC heater element 3 - Z132-
  7. Radiator
  8. Heat exchanger for highvoltage battery
  9. Thermostat
  10. Coolant expansion tank
  11. Coolant pump for high-voltage battery - V590-

Connection diagram - coolant hoses, refrigerant R1234yf

Connection diagram - coolant hoses, rear-wheel drive

Volkswagen ID.4. Connection diagram - coolant hoses, rear-wheel drive
  1. Charging unit 1 for highvoltage battery - AX4-
  • With control unit for high-voltage battery charging unit - J1050-
  1. Three-phase current drive - VX54-
  • With power and control electronics for electric drive - JX1-
  1. High-voltage battery 1 - AX2-
  2. Coolant pump for low-temperature circuit - V468-
  3. Mixing valve for highvoltage battery pre-heating - V683-
  4. Coolant pump for highvoltage battery - V590-
  5. PTC heater element 3 - Z132-
  6. Voltage converter - A19-
  7. Radiator
  8. Heat exchanger for highvoltage battery
  9. Thermostat
  10. Coolant expansion tank

Connection diagram - coolant hoses, four-wheel drive

Volkswagen ID.4. Connection diagram - coolant hoses, four-wheel drive
  1. Voltage converter - A19-
  2. Charging unit 1 for highvoltage battery - AX4-
  • With control unit for high-voltage battery charging unit - J1050-
  1. Three-phase current drive - VX54-
  • With power and control electronics for electric drive - JX1-
  1. Coolant hose
  2. Equipment version depending on vehicle version
  • High-voltage battery 1 - AX2-
  1. Coolant pump for highvoltage battery - V590-
  2. Coolant pump for low-temperature circuit - V468-
  3. Mixing valve for highvoltage battery pre-heating - V683-
  4. Power and control electronics 2 for electric drive - JX4-
  5. PTC heater element 3 - Z132-
  6. Radiator
  7. Heat exchanger for highvoltage battery
  8. Thermostat
  9. Coolant expansion tank

Overview of fitting locations - cooling system, rear-wheel drive

Volkswagen ID.4. Overview of fitting locations - cooling system, rear-wheel drive
  1. Three-phase current drive - VX54-
  • ⇒ Rep. gr. 10 ; Assembly overview - rear motor
  • ⇒ Rep. gr. 10 ; Removing rear motor
  • ⇒ Rep. gr. 10 ; Installing rear motor
  1. Temperature sensor - G18-
  • At top of charging unit 1 for high-voltage battery - AX4- in hose connection
  • ⇒ Rep. gr. 19 ; Removing and installing temperature sensor [G18]
  1. Charging unit 1 for highvoltage battery - AX4-
  • With control unit for high-voltage battery charger - J1050-
  • ⇒ Rep. gr. 93 ; Removing and installing charging unit 1 for highvoltage battery AX4
  1. Power and control electronics for electric drive - JX1-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive at rear
  1. Mixing valve for high-voltage battery pre-heating - V683-
  • ⇒ Rep. gr. 19 ; Removing and installing mixing valve for high-voltage battery pre-heating [V683]
  1. Mixing valve 2 for high-voltage battery pre-heating - V696-
  • Depending on equipment/version
  • ⇒ Rep. gr. 19 ; Removing and installing mixing valve 2 for high-voltage battery pre-heating [V696]
  1. Coolant temperature sender 2 for high-voltage battery - G899-
  • Battery outlet (return)
  • ⇒ Rep. gr. 19 ; Removing and installing coolant temperature sender 2 for high-voltage battery [G899]
  1. Coolant temperature sender 1 for high-voltage battery - G898-
  • Battery inlet (supply)
  • ⇒ Rep. gr. 19 ; Removing and installing coolant temperature sender 1 for high-voltage battery [G898]
  1. Coolant pump for low-temperature circuit - V468-
  • ⇒ Rep. gr. 19 ; Removing and installing coolant pump for low-temperature circuit [V468]
  1. Voltage converter - A19-
  • ⇒ Rep. gr. 93 ; Removing and installing voltage converter [A19]
  1. PTC heater element 3 - Z132-
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Coolant circuit; Removing and installing PTC heater element 3 [Z132]
  1. Radiator module
  • ⇒ Rep. gr. 19 ; Removing and installing radiator module
  1. Heat exchanger for high-voltage battery
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Refrigerant circuit; Removing and installing heat exchanger for high-voltage battery
  1. Coolant expansion tank
  • With coolant temperature display sender - G32-
  • ⇒ Rep. gr. 19 ; Removing and installing coolant expansion tank
  1. Thermostat
  • ⇒ Rep. gr. 19 ; Assembly overview - cooling system, rear-wheel drive
  1. Coolant pump for high-voltage battery - V590-
  • ⇒ Rep. gr. 19 ; Removing and installing coolant pump for high-voltage battery [V590]

Overview of fitting locations - cooling system, all-wheel drive

Volkswagen ID.4. Overview of fitting locations - cooling system, all-wheel drive
  1. Power and control electronics for electric drive - JX1-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive at rear
  1. Temperature sensor - G18-
  • At top of charging unit 1 for high-voltage battery - AX4- in hose connection
  • ⇒ Rep. gr. 19 ; Removing and installing temperature sensor [G18]
  1. Voltage converter - A19-
  • ⇒ Rep. gr. 93 ; Removing and installing voltage converter [A19]
  1. Charging unit 1 for highvoltage battery - AX4-
  • With control unit for high-voltage battery charger - J1050-
  • ⇒ Rep. gr. 93 ; Removing and installing charging unit 1 for highvoltage battery AX4
  1. Three-phase current drive - VX54-
  • ⇒ Rep. gr. 10 ; Assembly overview - rear motor
  • ⇒ Rep. gr. 10 ; Removing rear motor
  • ⇒ Rep. gr. 10 ; Installing rear motor
  1. Power and control electronics 2 for electric drive - JX4-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive, front
  1. Coolant pump for high-voltage battery - V590-
  • ⇒ Rep. gr. 19 ; Removing and installing coolant pump for high-voltage battery [V590]
  1. Mixing valve for high-voltage battery pre-heating - V683-
  • ⇒ Rep. gr. 19 ; Removing and installing mixing valve for high-voltage battery pre-heating [V683]
  1. Mixing valve 2 for high-voltage battery pre-heating - V696-
  • Depending on equipment/version
  • ⇒ Rep. gr. 19 ; Removing and installing mixing valve 2 for high-voltage battery pre-heating [V696]
  1. Coolant temperature sender 2 for high-voltage battery - G899-
  • Battery outlet (return)
  • ⇒ Rep. gr. 19 ; Removing and installing coolant temperature sender 2 for high-voltage battery [G899]
  1. Coolant temperature sender 1 for high-voltage battery - G898-
  • Battery inlet (supply)
  • ⇒ Rep. gr. 19 ; Removing and installing coolant temperature sender 1 for high-voltage battery [G898]
  1. Coolant pump for low-temperature circuit - V468-
  • ⇒ Rep. gr. 19 ; Removing and installing coolant pump for low-temperature circuit [V468]
  1. Three-phase current drive 2 - VX97-
  • ⇒ Rep. gr. 10 ; Assembly overview - front motor
  • ⇒ Rep. gr. 10 ; Removing front motor
  • ⇒ Rep. gr. 10 ; Installing front motor
  1. PTC heater element 3 - Z132-
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Coolant circuit; Removing and installing PTC heater element 3 [Z132]
  1. Radiator module
  • ⇒ Rep. gr. 19 ; Removing and installing radiator module
  1. Heat exchanger for high-voltage battery
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Refrigerant circuit; Removing and installing heat exchanger for high-voltage battery
  1. Coolant expansion tank
  • With coolant temperature display sender - G32-
  • ⇒ Rep. gr. 19 ; Removing and installing coolant expansion tank
  1. Thermostat
  • ⇒ Rep. gr. 19 ; Assembly overview - cooling system, all-wheel drive
  1. Heat pump valve unit
  • Depending on equipment/version
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Heat pump valve unit; Removing and installing heat pump valve unit

Assembly overview - cooling system, rear-wheel drive

Volkswagen ID.4. Assembly overview - cooling system, rear-wheel drive
  1. Assembly overview - cooling system, front right
  2. Assembly overview - cooling system, rear
  3. Assembly overview - cooling system, front left
  4. Assembly overview - cooling system, front right
    Volkswagen ID.4. Assembly overview - cooling system, rear-wheel drive
  5. Voltage converter - A19-
  • ⇒ Rep. gr. 93 ; Removing and installing voltage converter [A19]
  1. Hose clamp
  2. Bolt
  • Specified torque ⇒ Rep. gr. 93 ; Assembly overview - voltage converter
  1. Coolant hose
  2. Coolant hose
  3. O-ring
  4. Retaining clip
  5. Hose clamp
  6. Coolant hose
  7. Retaining clip
  • Qty. 2
  1. Hose clamp
  2. Coolant expansion tank
  • With coolant temperature display sender - G32-
  • ⇒ Rep. gr. 19 ; Removing and installing coolant expansion tank
  1. Thermostat
  • Starts to open at 15 ºC
  1. Bracket for coolant manifold
  2. Spreader rivet
  3. Coolant manifold
  • Coolant hose and coolant pipe are marked with numbers
  • Note allocation
  1. Assembly overview - cooling system, rear
    Volkswagen ID.4. Assembly overview - cooling system, rear-wheel drive
  2. Rear right coolant pipe
  3. Coolant hose
  4. Hose clamp
  5. Temperature sensor - G18-
  • ⇒ Rep. gr. 19 ; Removing and installing temperature sensor [G18]
  1. O-ring
  • Renew after removing
  1. Retaining clip
  2. O-ring
  3. Retaining clip
  4. Charging unit 1 for highvoltage battery - AX4-
  • With control unit for high-voltage battery charger - J1050-
  • ⇒ Rep. gr. 93 ; Removing and installing charging unit 1 for highvoltage battery AX4
  1. Power and control electronics for electric drive - JX1-
  • With three-phase current drive - VX54-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive at rear
  1. Coolant hose
  2. Retaining clip
  3. Hose clamp
  4. Coolant pipe
  • Return line
  1. Coolant pipe
  • Supply line
  1. Assembly overview - cooling system, front left
    Volkswagen ID.4. Assembly overview - cooling system, rear-wheel drive
  2. Hose clamp
  3. Coolant hose
  • Coolant hose and coolant pipe are marked with numbers
  • Note allocation
  1. Retaining clip
  2. Coolant pipe
  • Return line
  1. Coolant pipe
  • Supply line
  1. Coolant hose
  • Marking -V- = supply
  1. Coolant pump for low-temperature circuit - V468-
  • ⇒ Rep. gr. 19 ; Assembly overview - electric coolant pump
  • ⇒ Rep. gr. 19 ; Removing and installing coolant pump for low-temperature circuit [V468]
  1. Bolt
  • Qty. 4
  • 8 N·m
  1. Coolant hose
  • Marking -R- = return
  1. Coolant temperature sender 2 for high-voltage battery - G899-
  • ⇒ Rep. gr. 19 ; Assembly overview - coolant temperature sender
  • ⇒ Rep. gr. 19 ; Removing and installing coolant temperature sender 2 for high-voltage battery [G899]
  1. O-ring
  2. Retaining clip
  3. Coolant temperature sender 1 for high-voltage battery - G898-
  • ⇒ Rep. gr. 19 ; Assembly overview - coolant temperature sender
  • ⇒ Rep. gr. 19 ; Removing and installing coolant temperature sender 1 for high-voltage battery [G898]
  1. Coolant hose
  2. Coolant hose
  3. Hose clamp
  4. Retaining clip
  5. Bolt
  • 8 N·m
  1. Mixing valve for high-voltage battery pre-heating - V683-
  • ⇒ Rep. gr. 19 ; Assembly overview - coolant valves
  • ⇒ Rep. gr. 19 ; Removing and installing mixing valve for high-voltage battery pre-heating [V683]
  1. Mixing valve 2 for high-voltage battery pre-heating - V696- ❑ Depending on equipment/version
  • Rep. gr. 19 ; Assembly overview - coolant valves
  • ⇒ Rep. gr. 19 ; Removing and installing mixing valve 2 for high-voltage battery [V696] pre-heating, heat pump
  1. Bracket for mixing valve
  2. Bolt
  • Specified torque ⇒ Rep. gr. 93 ; Assembly overview - voltage converter
  1. Voltage converter - A19-
  • ⇒ Rep. gr. 93 ; Assembly overview - voltage converter
  • ⇒ Rep. gr. 93 ; Removing and installing voltage converter [A19]
  1. Retaining clip
  2. Coolant pump for high-voltage battery - V590-
  • ⇒ Rep. gr. 19 ; Assembly overview - electric coolant pump
  • ⇒ Rep. gr. 19 ; Removing and installing coolant pump for high-voltage battery [V590]
  1. Spreader rivet

Assembly overview - cooling system, all-wheel drive

  1. Assembly overview - cooling system, front right
  2. Assembly overview - cooling system, rear
  3. Assembly overview - cooling system, front left
    Volkswagen ID.4. Assembly overview - cooling system, all-wheel drive
  4. Assembly overview - cooling system, front right
    Volkswagen ID.4. Assembly overview - cooling system, all-wheel drive
  5. Coolant hose
  6. Retaining clip
  7. O-ring
  8. Retaining clip
  9. Hose clamp
  10. Thermostat
  • Starts to open at 15 ºC
  1. Coolant hose
  2. Hose clamp
  3. Coolant expansion tank
  • With coolant temperature display sender - G32-
  • ⇒ Rep. gr. 19 ; Removing and installing coolant expansion tank
  1. Coolant manifold
  • Coolant hose and coolant pipe are marked with numbers
  • Note allocation
  1. Spreader rivet
  2. Three-phase current drive 2 - VX97-
  • With power and control electronics 2 for electric drive - JX4-
  • ⇒ Rep. gr. 10 ; Assembly overview - front motor
  • ⇒ Rep. gr. 10 ; Removing front motor
  • ⇒ Rep. gr. 10 ; Installing front motor
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive, front
  1. Assembly overview - cooling system, rear
    Volkswagen ID.4. Assembly overview - cooling system, all-wheel drive
  2. Voltage converter - A19-
  • ⇒ Rep. gr. 93 ; Removing and installing voltage converter [A19]
  1. Charging unit 1 for highvoltage battery - AX4-
  • With control unit for high-voltage battery charger - J1050-
  • ⇒ Rep. gr. 93 ; Removing and installing charging unit 1 for highvoltage battery AX4
  1. Power and control electronics for electric drive - JX1-
  • With three-phase current drive - VX54-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive at rear
  1. O-ring
  2. Retaining clip
  3. Coolant hose
  4. Retaining clip
  5. Hose clamp
  6. Coolant pipe
  • Return line
  1. Coolant connection
  • ⇒ Rep. gr. 10 ; Assembly overview - motor
  1. Retaining clip
  2. Temperature sensor - G18-
  • ⇒ Rep. gr. 19 ; Removing and installing temperature sensor [G18]
  1. O-ring
  • Renew after removing
  1. Coolant hose
  2. Coolant pipe
  • Supply line
  1. Coolant hose
  2. Assembly overview - cooling system, front left
    Volkswagen ID.4. Assembly overview - cooling system, all-wheel drive
  3. Hose clamp
  4. Coolant pump for highvoltage battery - V590-
  • ⇒ Rep. gr. 19 ; Assembly overview - electric coolant pump
  • ⇒ Rep. gr. 19 ; Removing and installing coolant pump for highvoltage battery [V590]
  1. Coolant temperature sender 2 for high-voltage battery - G899-
  • ⇒ Rep. gr. 19 ; Assembly overview - coolant temperature sender
  • ⇒ Rep. gr. 19 ; Removing and installing coolant temperature sender 2 for highvoltage battery [G899]
  1. Retaining clip
  2. O-ring
  3. Bolt
  • Qty. 2
  • 8 N·m
  1. Retaining clip
  2. Coolant hose
  • Marking -R- = return
  1. Mixing valve for highvoltage battery pre-heating - V683-
  • ⇒ Rep. gr. 19 ; Assembly overview - coolant valves
  • ⇒ Rep. gr. 19 ; Removing and installing mixing valve for high-voltage battery pre-heating [V683]
  1. Bolt
  • Qty. 3
  • 8 N·m
  1. Coolant pipe
  • Return line
  1. Coolant temperature sender 1 for high-voltage battery - G898-
  • ⇒ Rep. gr. 19 ; Assembly overview - coolant temperature sender
  • ⇒ Rep. gr. 19 ; Removing and installing coolant temperature sender 1 for high-voltage battery [G898]
  1. Coolant pipe
  • Supply line
  1. Coolant hose
  2. Coolant hose
  • Marking -V- = supply
  1. Bolt
  • Qty. 2
  • 8 N·m
  1. Coolant pump for low-temperature circuit - V468-
  • ⇒ Rep. gr. 19 ; Assembly overview - electric coolant pump
  • ⇒ Rep. gr. 19 ; Removing and installing coolant pump for low-temperature circuit [V468]
  1. Coolant pipe
  2. PTC heater element 3 - Z132-
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Coolant circuit; Removing and installing PTC heater element 3 [Z132]
  1. Coolant hose
  2. Coolant hose
  3. Coolant hose
  4. Mixing valve holder
  5. Mixing valve 2 for high-voltage battery pre-heating - V696-
  • Depending on equipment/version
  • ⇒ Rep. gr. 19 ; Assembly overview - coolant valves
  • ⇒ Rep. gr. 19 ; Removing and installing mixing valve 2 for high-voltage battery pre-heating [V696]
  1. Retaining clip
  2. Coolant hose
  3. Three-phase current drive 2 - VX97-
  • With power and control electronics 2 for electric drive - JX4-
  • ⇒ Rep. gr. 10 ; Assembly overview - front motor
  • ⇒ Rep. gr. 10 ; Removing front motor
  • ⇒ Rep. gr. 10 ; Installing front motor
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive, front

Checking cooling system for leaks

Special tools and workshop equipment required

  • Cooling system tester - V.A.G 1274B-
  • adapter - VAS 691 005/5-
  • adapter for cooling system tester - V.A.G 1274/9-
  • cooling system tester - V.A.G 1274B-
  • Check cooling system tester - V.A.G 1274B- for leaks
  • Check cooling system for leaks
  • Check pressure relief valve in filler cap

Checking cooling system tester - V.A.G 1274B- for leaks

  • Operate hand pump several times to build up pressure of 3.0 bar.
  • Observe pressure on pressure gauge of cooling system tester for 30 seconds.

If pressure is not built up or pressure drops again, cooling system tester must not be used.

Checking cooling system for leaks

Important

  • Cooling system tester - V.A.G 1274B- checked for leaks.

CAUTION

The cooling system may be under pressure. Risk of scalding due to hot steam and hot coolant Danger of scalding skin and other parts of the body

  • Put on protective gloves.
  • Put on safety goggles.
  • Cover filler cap on expansion tank with a suitable cloth and open carefully to release pressure.
  • Open cap -arrow-.
Volkswagen ID.4. Checking cooling system for leaks
  • Screw adapter - VAS 691 005/5- -1- onto coolant expansion tank -2-.
  • Connect cooling system tester - V.A.G 1274B- -3- to adapter -1-.
  • Operate hand pump several times to build up pressure of 1.5 bar.
Volkswagen ID.4. Checking cooling system for leaks

Important

  • The pressure cannot drop by more than 0.2 bar within 10 minutes.
  • If pressure drops by more than 0.2 bar, locate leaks and rectify faults.

Note

A pressure drop of 0.2 bar within 10 minutes is caused by the coolant cooling down. Once the coolant temperature is the same as the ambient temperature there should be no pressure loss.

Important

  • If leaks were found and rectified, leak test must be repeated.
  • Release pressure on cooling system tester and remove from coolant expansion tank.
  • Screw on cap.

Checking pressure relief valve in cap

Important

  • Cooling system tester - V.A.G 1274B- checked for leaks.

CAUTION

The cooling system may be under pressure. Risk of scalding due to hot steam and hot coolant Danger of scalding skin and other parts of the body

  • Put on protective gloves.
  • Put on safety goggles.
  • Cover filler cap on expansion tank with a suitable cloth and open carefully to release pressure.
  • Open cap -arrow-.
Volkswagen ID.4. Checking pressure relief valve in cap
  • Connect cooling system tester - V.A.G 1274B- -1- and adapter for cooling system tester - V.A.G 1274/9- -2- to cap -3-.
  • Actuate hand pump -1- several times to generate pressure.

Important

  • Blue cap: pressure relief valve must open at pressure of 1.4 to 1.6 bar.
  • Black cap: pressure relief valve must open at pressure of 1.6 to 1.8 bar.
  • Renew filler cap -3-, if pressure relief valve does not open as described.
Volkswagen ID.4. Checking pressure relief valve in cap

Removing and installing coolant expansion tank

Special tools and workshop equipment required

  • hose clamps for hoses up to 25 mm - 3094-

Removing

CAUTION

The cooling system may be under pressure. Risk of scalding due to hot steam and hot coolant Danger of scalding skin and other parts of the body

  • Put on protective gloves.
  • Put on safety goggles.
  • Cover filler cap on expansion tank with a suitable cloth and open carefully to release pressure.
  • In order to release pressure from the cooling system, open filler cap of the coolant expansion tank -arrow- briefly, then close it again.
Volkswagen ID.4. Removing and installing coolant expansion tank
  • Disconnect electrical connector -1- of coolant shortage indicator sender - G32- .
  • Pull electrical wire -3- off coolant expansion tank -2-.
  • Push locking element -arrow- forwards and swing coolant expansion tank -2- out of mounting.
Volkswagen ID.4. Removing and installing coolant expansion tank
  • Clamp off coolant hoses -1- and -2- using hose clamps for hoses up to 25 mm - 3094- .
  • Open hose clip and pull off coolant hose -1-.
  • Seal connection on coolant expansion tank using a plug.
  • Turn coolant expansion tank over.
  • Open hose clip and pull off coolant hose -2-.
  • Drain coolant expansion tank.
Volkswagen ID.4. Removing and installing coolant expansion tank

Installing

Install in reverse order of removal, observing the following:

  • Fit coolant hoses, and secure them with hose clips. Observe installation markings when doing this.
  • Remove hose clamps.
  • Insert coolant expansion tank in receiver and engage.
  • Replenish coolant and check filling quality ⇒ Rep. gr. 19 ; Checking filling quality .

Checking filling quality

Special tools and workshop equipment required

  • adapter - VAS 691 005/5-
  • cooling system tester - V.A.G 1274B

Note

It is necessary to make sure that there is no air in the cooling system. If there is any air in the cooling system, the coolant level will drop far below the permissible level in the course of time. Overheating of the motor is also possible.

CAUTION

The cooling system may be under pressure. Risk of scalding due to hot steam and hot coolant Danger of scalding skin and other parts of the body

  • Put on protective gloves.
  • Put on safety goggles.
  • Cover filler cap on expansion tank with a suitable cloth and open carefully to release pressure.
  • Open sealing cap of coolant expansion tank -arrow-.
Volkswagen ID.4. Checking filling quality
  • Check coolant level. It must be approx. 10 mm above the max. marking or be at the max. marking -1-. If necessary, top up with coolant.
Volkswagen ID.4. Checking filling quality
  • Fit cooling system tester - V.A.G 1274B- -3- with adapter - VAS 691 005/5- -1- onto coolant expansion tank -2-.
  • Build up pressure of 1.5 bar using hand pump of cooling system tester.
  • Observe coolant level in expansion tank.
Volkswagen ID.4. Checking filling quality

If the coolant level in the coolant expansion tank has dropped more than 20 mm, this is an indication of an air bubble in the cooling system.

  • Carry out function "Bleed cooling system" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • Repeat filling quality check.

If the coolant level in the coolant expansion tank has dropped less than 20 mm, the cooling system has been filled correctly.

Continued

  • Release pressure at hand pump of cooling system tester -3-.
  • Detach adapter -1- from coolant expansion tank.
Volkswagen ID.4. Checking filling quality

Draining coolant

Special tools and workshop equipment required

  • cooling system service unit - VAS 531 011-
  • hose clamp up to 40 mm - 3093-

NOTICE

Risk of damage to high-voltage components due to overheating.

  • Do not perform high-voltage charging if coolant has been drained.
  • Indicate this on the vehicle accordingly.

Procedure

Important

  • Observe operating manual of cooling system service unit - VAS 531 011- .
  • Make sure that the "DRAIN" container of the cooling system service unit is sufficiently empty to accept 12 litres of coolant.

Note

12 litres of coolant correspond to the total capacity of the cooling system. Due to the complexity of the cooling system, its total capacity cannot be discharged.

CAUTION

The cooling system may be under pressure. Risk of scalding due to hot steam and hot coolant Danger of scalding skin and other parts of the body

  • Put on protective gloves.
  • Put on safety goggles.
  • Cover filler cap on expansion tank with a suitable cloth and open carefully to release pressure.
  • Open filler cap -arrow- for coolant expansion tank.
  • Screw adapter from cooling system service unit onto coolant expansion tank.
  • Connect service hose.

Important

  • Do not disconnect service hose from cooling system service unit.
Volkswagen ID.4. Draining coolant
  • Remove rear centre underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear centre underbody cladding .
  • Position cooling system service unit under coupling point to collect coolant.
  • In main menu select "Vehicle maintenance" and "Drain system".
  • Start "Draining procedure".
  • Open clip -arrow- on power and control electronics for electric drive - JX1- , and pull off coolant hose -1-.
  • Drain coolant into drip tray of cooling system service unit.
Volkswagen ID.4. Draining coolant
  • Clamp off coolant hose -1- using hose clamp up to 40 mm - 3093- .
  • Attach commercially available coolant hose to connection -1- on motor.
  • Hold commercially available coolant hose into funnel of cooling system service unit while draining coolant.
  • Select "Drain system" procedure.
  • Follow instructions on display, and blow out coolant until only small amounts are dripping out or until only air flows out.
  • If necessary, start "Drain system" procedure again.
  • Disconnect commercially available coolant hose from coolant hose connection -1- on motor.
  • Remove hose clamp on coolant hose -1-.
  • Hold coolant hose -1- in funnel of cooling system service unit while draining coolant.
  • Start "Drain system" procedure again.
  • Follow instructions on display, and blow out coolant until only small amounts are dripping out or until only air flows out.
  • If necessary, start "Drain system" procedure again.
  • Assemble cooling system.
Volkswagen ID.4. Draining coolant

Filling cooling system

Special tools and workshop equipment required

  • cooling system service unit - VAS 531 011-

Filling cooling system

Important

  • Observe operating manual of cooling system service unit - VAS 531 011- .
  • Fill "NEW" container of cooling system service unit - VAS 531 011- with sufficient coolant mixed in proper ratio ⇒ Safety information and repair notes; Rep. gr. 00 ; Repair notes; Replacement parts, servicing materials and consumables .
  • Make sure that all coolant hoses are connected.
  • Connect cooling system service unit.
  • From the main menu, select "Vehicle maintenance".
  • In the menu, select "Pressure test", and carry out hydraulic leak test.
  • Test duration => 120 s
  • Max. delta P => 40 mbar
  • Test pressure => 2000 mbar
  • Observe messages on display.
  • The result will be displayed, after the test is completed.
  • In the menu, select "Vacuum phase", and carry out hydraulic leak test.
  • Time => 240 s
  • Specified pressure => 40 mbar
  • Max. delta P => 30 mbar
  • Test duration => 120 s
  • Observe messages on display.
  • The result will be displayed, after the test is completed.
  • Repeat procedure if necessary.
  • In the menu, select "Charge system", and start filling.
  • Filling quantity => Enter mass of 12000 g which corresponds to 12 litres.
  • When the charging procedure is completed, the display shows the amount of filled coolant.
  • When the charging procedure is completed, the service unit automatically starts cleaning the hoses.
  • Follow the instructions on the display, and do not interrupt the process.
  • The result will be displayed, after the test is completed.
  • Repeat procedure if necessary.
  • From the main menu, select "Vehicle maintenance".
  • In the menu, select "Bleed system", and carry out bleeding procedure.
  • Test pressure => 1800 mbar
  • Carry out function "Bleed cooling system" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Important

  • Carry out this function 2 times in succession.
  • Remove adapter with service hose from coolant expansion tank.
  • Fill or extract coolant as necessary.

Important

  • Coolant level must be 10 mm above max. marking -1-.

Note

This excess amount of coolant is necessary since the coolant level may decrease automatically as the vehicle is operated.

  • ⇒ Rep. gr. 19 ; Check filling quality .
Volkswagen ID.4. Filling cooling system